| Message ID | tencent_AB776DFEB1B993E8B3F0BD5A4BF420600407@qq.com (mailing list archive) |
|---|---|
| State | Queued |
| Headers | show |
| Series | [v4,1/3] dt-bindings: vendor-prefixes: add thwc | expand |
On 14.01.2023 07:38, Yang Xiwen wrote: > This commit adds support for the ufi-001C and uf896 WiFi/LTE dongle made by > Tong Heng Wei Chuang based on MSM8916. > uf896 is another variant for the usb stick. The board design > differs by using different gpios for the keys and leds. > > Note: The original firmware does not support 64-bit OS. It is necessary > to flash 64-bit TZ firmware to boot arm64. > > Currently supported: > - All CPU cores > - Buttons > - LEDs > - Modem > - SDHC > - USB Device Mode > - UART > > Co-developed-by: Jaime Breva <jbreva@nayarsystems.com> > Signed-off-by: Jaime Breva <jbreva@nayarsystems.com> > Co-developed-by: Nikita Travkin <nikita@trvn.ru> > Signed-off-by: Nikita Travkin <nikita@trvn.ru> > Signed-off-by: Yang Xiwen <forbidden405@foxmail.com> > --- Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Konrad > arch/arm64/boot/dts/qcom/Makefile | 2 + > .../boot/dts/qcom/msm8916-thwc-uf896.dts | 39 +++ > .../boot/dts/qcom/msm8916-thwc-ufi001c.dts | 39 +++ > arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi | 250 ++++++++++++++++++ > 4 files changed, 330 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts > create mode 100644 arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts > create mode 100644 arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index e442a81895d04..d83e02c84d42c 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -22,6 +22,8 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-e7.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-grandmax.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-j5.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-serranove.dtb > +dtb-$(CONFIG_ARCH_QCOM) += msm8916-thwc-uf896.dtb > +dtb-$(CONFIG_ARCH_QCOM) += msm8916-thwc-ufi001c.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt88047.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8953-motorola-potter.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-daisy.dtb > diff --git a/arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts b/arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts > new file mode 100644 > index 0000000000000..c492db8561904 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts > @@ -0,0 +1,39 @@ > +// SPDX-License-Identifier: GPL-2.0-only > + > +/dts-v1/; > + > +#include "msm8916-ufi.dtsi" > + > +/ { > + model = "uf896 4G Modem Stick"; > + compatible = "thwc,uf896", "qcom,msm8916"; > +}; > + > +&button_restart { > + gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>; > +}; > + > +&led_r { > + gpios = <&msmgpio 82 GPIO_ACTIVE_HIGH>; > +}; > + > +&led_g { > + gpios = <&msmgpio 83 GPIO_ACTIVE_HIGH>; > +}; > + > +&led_b { > + gpios = <&msmgpio 81 GPIO_ACTIVE_HIGH>; > +}; > + > +&button_default { > + pins = "gpio35"; > + bias-pull-up; > +}; > + > +&gpio_leds_default { > + pins = "gpio81", "gpio82", "gpio83"; > +}; > + > +&sim_ctrl_default { > + pins = "gpio1", "gpio2"; > +}; > diff --git a/arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts b/arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts > new file mode 100644 > index 0000000000000..700cf81cbf8c0 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts > @@ -0,0 +1,39 @@ > +// SPDX-License-Identifier: GPL-2.0-only > + > +/dts-v1/; > + > +#include "msm8916-ufi.dtsi" > + > +/ { > + model = "ufi-001c/ufi-001b 4G Modem Stick"; > + compatible = "thwc,ufi001c", "qcom,msm8916"; > +}; > + > +&button_restart { > + gpios = <&msmgpio 37 GPIO_ACTIVE_HIGH>; > +}; > + > +&led_r { > + gpios = <&msmgpio 22 GPIO_ACTIVE_HIGH>; > +}; > + > +&led_g { > + gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>; > +}; > + > +&led_b { > + gpios = <&msmgpio 20 GPIO_ACTIVE_HIGH>; > +}; > + > +&button_default { > + pins = "gpio37"; > + bias-pull-down; > +}; > + > +&gpio_leds_default { > + pins = "gpio20", "gpio21", "gpio22"; > +}; > + > +&sim_ctrl_default { > + pins = "gpio1", "gpio2"; > +}; > diff --git a/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi b/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi > new file mode 100644 > index 0000000000000..790a9696da9de > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi > @@ -0,0 +1,250 @@ > +// SPDX-License-Identifier: GPL-2.0-only > + > +#include "msm8916-pm8916.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/leds/common.h> > + > +/ { > + chassis-type = "embedded"; > + > + aliases { > + serial0 = &blsp1_uart2; > + }; > + > + chosen { > + stdout-path = "serial0"; > + }; > + > + reserved-memory { > + mpss_mem: mpss@86800000 { > + reg = <0x0 0x86800000 0x0 0x5500000>; > + no-map; > + }; > + > + gps_mem: gps@8bd00000 { > + reg = <0x0 0x8bd00000 0x0 0x200000>; > + no-map; > + }; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + pinctrl-0 = <&button_default>; > + pinctrl-names = "default"; > + > + label = "GPIO Buttons"; > + > + /* GPIO is board-specific */ > + button_restart: button-restart { > + label = "Restart"; > + linux,code = <KEY_RESTART>; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + pinctrl-0 = <&gpio_leds_default>; > + pinctrl-names = "default"; > + > + /* > + * GPIOs are board-specific. > + * Functions and default-states defined here are fallbacks. > + * Feel free to override them if your board is different. > + */ > + led_r: led-r { > + color = <LED_COLOR_ID_RED>; > + default-state = "on"; > + function = LED_FUNCTION_POWER; > + }; > + > + led_g: led-g { > + color = <LED_COLOR_ID_GREEN>; > + default-state = "off"; > + function = LED_FUNCTION_WLAN; > + }; > + > + led_b: led-b { > + color = <LED_COLOR_ID_BLUE>; > + default-state = "off"; > + function = LED_FUNCTION_WAN; > + }; > + }; > +}; > + > +&bam_dmux { > + status = "okay"; > +}; > + > +&bam_dmux_dma { > + status = "okay"; > +}; > + > +&blsp1_uart2 { > + status = "okay"; > +}; > + > +/* Remove &dsi_phy0 from clocks to make sure that gcc probes with display disabled */ > +&gcc { > + clocks = <&xo_board>, <&sleep_clk>, <0>, <0>, <0>, <0>, <0>; > +}; > + > +&mpss { > + pinctrl-0 = <&sim_ctrl_default>; > + pinctrl-names = "default"; > + > + status = "okay"; > +}; > + > +&pm8916_usbin { > + status = "okay"; > +}; > + > +&pronto { > + status = "okay"; > +}; > + > +&sdhc_1 { > + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; > + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; > + pinctrl-names = "default", "sleep"; > + > + status = "okay"; > +}; > + > +&usb { > + extcon = <&pm8916_usbin>; > + dr_mode = "peripheral"; > + > + status = "okay"; > +}; > + > +&usb_hs_phy { > + extcon = <&pm8916_usbin>; > +}; > + > +&smd_rpm_regulators { > + vdd_l1_l2_l3-supply = <&pm8916_s3>; > + vdd_l4_l5_l6-supply = <&pm8916_s4>; > + vdd_l7-supply = <&pm8916_s4>; > + > + s3 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1300000>; > + }; > + > + s4 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2100000>; > + }; > + > + l1 { > + regulator-min-microvolt = <1225000>; > + regulator-max-microvolt = <1225000>; > + }; > + > + l2 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + }; > + > + l4 { > + regulator-min-microvolt = <2050000>; > + regulator-max-microvolt = <2050000>; > + }; > + > + l5 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l7 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + l8 { > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2900000>; > + }; > + > + l9 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l10 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <2800000>; > + }; > + > + l11 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2950000>; > + regulator-system-load = <200000>; > + regulator-allow-set-load; > + }; > + > + l12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2950000>; > + }; > + > + l13 { > + regulator-min-microvolt = <3075000>; > + regulator-max-microvolt = <3075000>; > + }; > + > + l14 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l15 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l16 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + l17 { > + regulator-min-microvolt = <2850000>; > + regulator-max-microvolt = <2850000>; > + }; > + > + l18 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <2700000>; > + }; > +}; > + > +&msmgpio { > + /* pins are board-specific */ > + button_default: button-default-state { > + function = "gpio"; > + drive-strength = <2>; > + }; > + > + gpio_leds_default: gpio-leds-default-state { > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + sim_ctrl_default: sim-ctrl-default-state { > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + output-low; > + }; > +};
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index e442a81895d04..d83e02c84d42c 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -22,6 +22,8 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-e7.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-grandmax.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-j5.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-serranove.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8916-thwc-uf896.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8916-thwc-ufi001c.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt88047.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8953-motorola-potter.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-daisy.dtb diff --git a/arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts b/arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts new file mode 100644 index 0000000000000..c492db8561904 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts @@ -0,0 +1,39 @@ +// SPDX-License-Identifier: GPL-2.0-only + +/dts-v1/; + +#include "msm8916-ufi.dtsi" + +/ { + model = "uf896 4G Modem Stick"; + compatible = "thwc,uf896", "qcom,msm8916"; +}; + +&button_restart { + gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>; +}; + +&led_r { + gpios = <&msmgpio 82 GPIO_ACTIVE_HIGH>; +}; + +&led_g { + gpios = <&msmgpio 83 GPIO_ACTIVE_HIGH>; +}; + +&led_b { + gpios = <&msmgpio 81 GPIO_ACTIVE_HIGH>; +}; + +&button_default { + pins = "gpio35"; + bias-pull-up; +}; + +&gpio_leds_default { + pins = "gpio81", "gpio82", "gpio83"; +}; + +&sim_ctrl_default { + pins = "gpio1", "gpio2"; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts b/arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts new file mode 100644 index 0000000000000..700cf81cbf8c0 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts @@ -0,0 +1,39 @@ +// SPDX-License-Identifier: GPL-2.0-only + +/dts-v1/; + +#include "msm8916-ufi.dtsi" + +/ { + model = "ufi-001c/ufi-001b 4G Modem Stick"; + compatible = "thwc,ufi001c", "qcom,msm8916"; +}; + +&button_restart { + gpios = <&msmgpio 37 GPIO_ACTIVE_HIGH>; +}; + +&led_r { + gpios = <&msmgpio 22 GPIO_ACTIVE_HIGH>; +}; + +&led_g { + gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>; +}; + +&led_b { + gpios = <&msmgpio 20 GPIO_ACTIVE_HIGH>; +}; + +&button_default { + pins = "gpio37"; + bias-pull-down; +}; + +&gpio_leds_default { + pins = "gpio20", "gpio21", "gpio22"; +}; + +&sim_ctrl_default { + pins = "gpio1", "gpio2"; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi b/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi new file mode 100644 index 0000000000000..790a9696da9de --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi @@ -0,0 +1,250 @@ +// SPDX-License-Identifier: GPL-2.0-only + +#include "msm8916-pm8916.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> + +/ { + chassis-type = "embedded"; + + aliases { + serial0 = &blsp1_uart2; + }; + + chosen { + stdout-path = "serial0"; + }; + + reserved-memory { + mpss_mem: mpss@86800000 { + reg = <0x0 0x86800000 0x0 0x5500000>; + no-map; + }; + + gps_mem: gps@8bd00000 { + reg = <0x0 0x8bd00000 0x0 0x200000>; + no-map; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&button_default>; + pinctrl-names = "default"; + + label = "GPIO Buttons"; + + /* GPIO is board-specific */ + button_restart: button-restart { + label = "Restart"; + linux,code = <KEY_RESTART>; + }; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-0 = <&gpio_leds_default>; + pinctrl-names = "default"; + + /* + * GPIOs are board-specific. + * Functions and default-states defined here are fallbacks. + * Feel free to override them if your board is different. + */ + led_r: led-r { + color = <LED_COLOR_ID_RED>; + default-state = "on"; + function = LED_FUNCTION_POWER; + }; + + led_g: led-g { + color = <LED_COLOR_ID_GREEN>; + default-state = "off"; + function = LED_FUNCTION_WLAN; + }; + + led_b: led-b { + color = <LED_COLOR_ID_BLUE>; + default-state = "off"; + function = LED_FUNCTION_WAN; + }; + }; +}; + +&bam_dmux { + status = "okay"; +}; + +&bam_dmux_dma { + status = "okay"; +}; + +&blsp1_uart2 { + status = "okay"; +}; + +/* Remove &dsi_phy0 from clocks to make sure that gcc probes with display disabled */ +&gcc { + clocks = <&xo_board>, <&sleep_clk>, <0>, <0>, <0>, <0>, <0>; +}; + +&mpss { + pinctrl-0 = <&sim_ctrl_default>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pm8916_usbin { + status = "okay"; +}; + +&pronto { + status = "okay"; +}; + +&sdhc_1 { + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; + pinctrl-names = "default", "sleep"; + + status = "okay"; +}; + +&usb { + extcon = <&pm8916_usbin>; + dr_mode = "peripheral"; + + status = "okay"; +}; + +&usb_hs_phy { + extcon = <&pm8916_usbin>; +}; + +&smd_rpm_regulators { + vdd_l1_l2_l3-supply = <&pm8916_s3>; + vdd_l4_l5_l6-supply = <&pm8916_s4>; + vdd_l7-supply = <&pm8916_s4>; + + s3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1300000>; + }; + + s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2100000>; + }; + + l1 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + l4 { + regulator-min-microvolt = <2050000>; + regulator-max-microvolt = <2050000>; + }; + + l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l8 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2900000>; + }; + + l9 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + l10 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2800000>; + }; + + l11 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-system-load = <200000>; + regulator-allow-set-load; + }; + + l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + l13 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + }; + + l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l16 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + l18 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; +}; + +&msmgpio { + /* pins are board-specific */ + button_default: button-default-state { + function = "gpio"; + drive-strength = <2>; + }; + + gpio_leds_default: gpio-leds-default-state { + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + sim_ctrl_default: sim-ctrl-default-state { + function = "gpio"; + drive-strength = <2>; + bias-disable; + output-low; + }; +};