@@ -1273,7 +1273,7 @@ static int fdc_configure(int fdc)
*
* These values are rounded up to the next highest available delay time.
*/
-static void fdc_specify(void)
+static void fdc_specify(int fdc, int drive)
{
unsigned char spec1;
unsigned char spec2;
@@ -1285,10 +1285,10 @@ static void fdc_specify(void)
int hlt_max_code = 0x7f;
int hut_max_code = 0xf;
- if (fdc_state[current_fdc].need_configure &&
- fdc_state[current_fdc].version >= FDC_82072A) {
- fdc_configure(current_fdc);
- fdc_state[current_fdc].need_configure = 0;
+ if (fdc_state[fdc].need_configure &&
+ fdc_state[fdc].version >= FDC_82072A) {
+ fdc_configure(fdc);
+ fdc_state[fdc].need_configure = 0;
}
switch (raw_cmd->rate & 0x03) {
@@ -1297,13 +1297,13 @@ static void fdc_specify(void)
break;
case 1:
dtr = 300;
- if (fdc_state[current_fdc].version >= FDC_82078) {
+ if (fdc_state[fdc].version >= FDC_82078) {
/* chose the default rate table, not the one
* where 1 = 2 Mbps */
- output_byte(current_fdc, FD_DRIVESPEC);
- if (need_more_output(current_fdc) == MORE_OUTPUT) {
- output_byte(current_fdc, UNIT(current_drive));
- output_byte(current_fdc, 0xc0);
+ output_byte(fdc, FD_DRIVESPEC);
+ if (need_more_output(fdc) == MORE_OUTPUT) {
+ output_byte(fdc, UNIT(drive));
+ output_byte(fdc, 0xc0);
}
}
break;
@@ -1312,14 +1312,14 @@ static void fdc_specify(void)
break;
}
- if (fdc_state[current_fdc].version >= FDC_82072) {
+ if (fdc_state[fdc].version >= FDC_82072) {
scale_dtr = dtr;
hlt_max_code = 0x00; /* 0==256msec*dtr0/dtr (not linear!) */
hut_max_code = 0x0; /* 0==256msec*dtr0/dtr (not linear!) */
}
/* Convert step rate from microseconds to milliseconds and 4 bits */
- srt = 16 - DIV_ROUND_UP(drive_params[current_drive].srt * scale_dtr / 1000,
+ srt = 16 - DIV_ROUND_UP(drive_params[drive].srt * scale_dtr / 1000,
NOMINAL_DTR);
if (slow_floppy)
srt = srt / 4;
@@ -1327,14 +1327,14 @@ static void fdc_specify(void)
SUPBOUND(srt, 0xf);
INFBOUND(srt, 0);
- hlt = DIV_ROUND_UP(drive_params[current_drive].hlt * scale_dtr / 2,
+ hlt = DIV_ROUND_UP(drive_params[drive].hlt * scale_dtr / 2,
NOMINAL_DTR);
if (hlt < 0x01)
hlt = 0x01;
else if (hlt > 0x7f)
hlt = hlt_max_code;
- hut = DIV_ROUND_UP(drive_params[current_drive].hut * scale_dtr / 16,
+ hut = DIV_ROUND_UP(drive_params[drive].hut * scale_dtr / 16,
NOMINAL_DTR);
if (hut < 0x1)
hut = 0x1;
@@ -1345,12 +1345,12 @@ static void fdc_specify(void)
spec2 = (hlt << 1) | (use_virtual_dma & 1);
/* If these parameters did not change, just return with success */
- if (fdc_state[current_fdc].spec1 != spec1 ||
- fdc_state[current_fdc].spec2 != spec2) {
+ if (fdc_state[fdc].spec1 != spec1 ||
+ fdc_state[fdc].spec2 != spec2) {
/* Go ahead and set spec1 and spec2 */
- output_byte(current_fdc, FD_SPECIFY);
- output_byte(current_fdc, fdc_state[current_fdc].spec1 = spec1);
- output_byte(current_fdc, fdc_state[current_fdc].spec2 = spec2);
+ output_byte(fdc, FD_SPECIFY);
+ output_byte(fdc, fdc_state[fdc].spec1 = spec1);
+ output_byte(fdc, fdc_state[fdc].spec2 = spec2);
}
} /* fdc_specify */
@@ -1946,12 +1946,12 @@ static void floppy_ready(void)
if (raw_cmd->flags & (FD_RAW_NEED_SEEK | FD_RAW_NEED_DISK)) {
perpendicular_mode(current_fdc);
- fdc_specify(); /* must be done here because of hut, hlt ... */
+ fdc_specify(current_fdc, current_drive); /* must be done here because of hut, hlt ... */
seek_floppy();
} else {
if ((raw_cmd->flags & FD_RAW_READ) ||
(raw_cmd->flags & FD_RAW_WRITE))
- fdc_specify();
+ fdc_specify(current_fdc, current_drive);
setup_rw_floppy();
}
}
Now the fdc and drive are passed in argument so that the function does not use current_fdc nor current_drive anymore. Signed-off-by: Willy Tarreau <w@1wt.eu> --- drivers/block/floppy.c | 42 +++++++++++++++++++++--------------------- 1 file changed, 21 insertions(+), 21 deletions(-)