@@ -245,9 +245,8 @@ mmc_send_cxd_native(struct mmc_host *host, u32 arg, u32 *cxd, int opcode)
* NOTE: void *buf, caller for the buf is required to use DMA-capable
* buffer or on-stack buffer (with some overhead in callee).
*/
-static int
-mmc_send_cxd_data(struct mmc_card *card, struct mmc_host *host,
- u32 opcode, void *buf, unsigned len)
+int mmc_send_adtc_data(struct mmc_card *card, struct mmc_host *host, u32 opcode,
+ u32 args, void *buf, unsigned len)
{
struct mmc_request mrq = {};
struct mmc_command cmd = {};
@@ -258,7 +257,7 @@ mmc_send_cxd_data(struct mmc_card *card, struct mmc_host *host,
mrq.data = &data;
cmd.opcode = opcode;
- cmd.arg = 0;
+ cmd.arg = args;
/* NOTE HACK: the MMC_RSP_SPI_R1 is always correct here, but we
* rely on callers to never use this with "native" calls for reading
@@ -304,7 +303,7 @@ static int mmc_spi_send_cxd(struct mmc_host *host, u32 *cxd, u32 opcode)
if (!cxd_tmp)
return -ENOMEM;
- ret = mmc_send_cxd_data(NULL, host, opcode, cxd_tmp, 16);
+ ret = mmc_send_adtc_data(NULL, host, opcode, 0, cxd_tmp, 16);
if (ret)
goto err;
@@ -352,7 +351,7 @@ int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd)
if (!ext_csd)
return -ENOMEM;
- err = mmc_send_cxd_data(card, card->host, MMC_SEND_EXT_CSD, ext_csd,
+ err = mmc_send_adtc_data(card, card->host, MMC_SEND_EXT_CSD, 0, ext_csd,
512);
if (err)
kfree(ext_csd);
@@ -25,6 +25,8 @@ int mmc_set_dsr(struct mmc_host *host);
int mmc_go_idle(struct mmc_host *host);
int mmc_send_op_cond(struct mmc_host *host, u32 ocr, u32 *rocr);
int mmc_set_relative_addr(struct mmc_card *card);
+int mmc_send_adtc_data(struct mmc_card *card, struct mmc_host *host, u32 opcode,
+ u32 args, void *buf, unsigned len);
int mmc_send_csd(struct mmc_card *card, u32 *csd);
int __mmc_send_status(struct mmc_card *card, u32 *status, unsigned int retries);
int mmc_send_status(struct mmc_card *card, u32 *status);
The CMD48 is used to read the SD function extension registers, which is an ADTC type of command with an R1 response. It's very similar to the commands that are currently being managed via mmc_send_cxd_data(). Therefore, let's adapt mmc_send_cxd_data() so it can manage CMD48 as well. While at it, let's also rename the function to mmc_send_adtc_data() as it better describes its purpose. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> --- drivers/mmc/core/mmc_ops.c | 11 +++++------ drivers/mmc/core/mmc_ops.h | 2 ++ 2 files changed, 7 insertions(+), 6 deletions(-)