| Message ID | 1591687933-19495-3-git-send-email-Anson.Huang@nxp.com (mailing list archive) |
|---|---|
| State | Awaiting Upstream, archived |
| Headers | show |
| Series | Support building i.MX8 SoCs clock driver as module | expand |
> From: Anson Huang <Anson.Huang@nxp.com> > Sent: Tuesday, June 9, 2020 3:32 PM > > i.MX common clock drivers may support module build, so it is NOT selected by > default, for ARCH_MXC ARMv7 platforms, need to select it manually to make > build pass. > > Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Can't the original def_xxx work? config MXC_CLK tristate def_tristate ARCH_MXC Regards Aisheng > --- > No change. > --- > arch/arm/mach-imx/Kconfig | 1 + > 1 file changed, 1 insertion(+) > > diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig index > e7d7b90..47b10d2 100644 > --- a/arch/arm/mach-imx/Kconfig > +++ b/arch/arm/mach-imx/Kconfig > @@ -4,6 +4,7 @@ menuconfig ARCH_MXC > depends on ARCH_MULTI_V4_V5 || ARCH_MULTI_V6_V7 || > ARM_SINGLE_ARMV7M > select ARCH_SUPPORTS_BIG_ENDIAN > select CLKSRC_IMX_GPT > + select MXC_CLK > select GENERIC_IRQ_CHIP > select GPIOLIB > select PINCTRL > -- > 2.7.4
> Subject: RE: [PATCH V2 2/9] ARM: imx: Select MXC_CLK for ARCH_MXC > > > From: Anson Huang <Anson.Huang@nxp.com> > > Sent: Tuesday, June 9, 2020 3:32 PM > > > > i.MX common clock drivers may support module build, so it is NOT > > selected by default, for ARCH_MXC ARMv7 platforms, need to select it > > manually to make build pass. > > > > Signed-off-by: Anson Huang <Anson.Huang@nxp.com> > > Can't the original def_xxx work? > > config MXC_CLK > tristate > def_tristate ARCH_MXC Such change will make MXC_CLK=y even all i.MX8 SoCs clock drivers are selected as module, so it does NOT meet the requirement of module support. Below is from .config when all i.MX8 SoCs clock drivers are configured to module. CONFIG_MXC_CLK=y CONFIG_MXC_CLK_SCU=m CONFIG_CLK_IMX8MM=m CONFIG_CLK_IMX8MN=m CONFIG_CLK_IMX8MP=m CONFIG_CLK_IMX8MQ=m CONFIG_CLK_IMX8QXP=m Anson
> From: Anson Huang <anson.huang@nxp.com> > Sent: Wednesday, June 17, 2020 8:36 PM > > > Subject: RE: [PATCH V2 2/9] ARM: imx: Select MXC_CLK for ARCH_MXC > > > > > From: Anson Huang <Anson.Huang@nxp.com> > > > Sent: Tuesday, June 9, 2020 3:32 PM > > > > > > i.MX common clock drivers may support module build, so it is NOT > > > selected by default, for ARCH_MXC ARMv7 platforms, need to select it > > > manually to make build pass. > > > > > > Signed-off-by: Anson Huang <Anson.Huang@nxp.com> > > > > Can't the original def_xxx work? > > > > config MXC_CLK > > tristate > > def_tristate ARCH_MXC > > Such change will make MXC_CLK=y even all i.MX8 SoCs clock drivers are selected > as module, so it does NOT meet the requirement of module support. Below is > from .config when all > i.MX8 SoCs clock drivers are configured to module. > > CONFIG_MXC_CLK=y > CONFIG_MXC_CLK_SCU=m > CONFIG_CLK_IMX8MM=m > CONFIG_CLK_IMX8MN=m > CONFIG_CLK_IMX8MP=m > CONFIG_CLK_IMX8MQ=m > CONFIG_CLK_IMX8QXP=m > It works at my side. Below is my changes based on your patchset: $ git diff diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig index 47b10d20f411..e7d7b90e2cf8 100644 --- a/arch/arm/mach-imx/Kconfig +++ b/arch/arm/mach-imx/Kconfig @@ -4,7 +4,6 @@ menuconfig ARCH_MXC depends on ARCH_MULTI_V4_V5 || ARCH_MULTI_V6_V7 || ARM_SINGLE_ARMV7M select ARCH_SUPPORTS_BIG_ENDIAN select CLKSRC_IMX_GPT - select MXC_CLK select GENERIC_IRQ_CHIP select GPIOLIB select PINCTRL diff --git a/drivers/clk/imx/Kconfig b/drivers/clk/imx/Kconfig index 26cedbfe386c..f7b3e3a2cb9f 100644 --- a/drivers/clk/imx/Kconfig +++ b/drivers/clk/imx/Kconfig @@ -3,6 +3,7 @@ config MXC_CLK tristate "IMX clock" depends on ARCH_MXC + def_tristate ARCH_MXC config MXC_CLK_SCU tristate "IMX SCU clock" Regards Aisheng > Anson
> -----Original Message----- > From: Aisheng Dong <aisheng.dong@nxp.com> > Sent: 2020年6月18日 11:09 > To: Anson Huang <anson.huang@nxp.com>; linux@armlinux.org.uk; > shawnguo@kernel.org; s.hauer@pengutronix.de; kernel@pengutronix.de; > festevam@gmail.com; mturquette@baylibre.com; sboyd@kernel.org; > oleksandr.suvorov@toradex.com; Stefan Agner <stefan.agner@toradex.com>; > arnd@arndb.de; Abel Vesa <abel.vesa@nxp.com>; Peng Fan > <peng.fan@nxp.com>; tglx@linutronix.de; allison@lohutok.net; > gregkh@linuxfoundation.org; info@metux.net; Leonard Crestez > <leonard.crestez@nxp.com>; Andy Duan <fugang.duan@nxp.com>; Daniel > Baluta <daniel.baluta@nxp.com>; yuehaibing@huawei.com; > sfr@canb.auug.org.au; linux-arm-kernel@lists.infradead.org; > linux-kernel@vger.kernel.org; linux-clk@vger.kernel.org > Cc: dl-linux-imx <linux-imx@nxp.com> > Subject: RE: [PATCH V2 2/9] ARM: imx: Select MXC_CLK for ARCH_MXC > > > From: Anson Huang <anson.huang@nxp.com> > > Sent: Wednesday, June 17, 2020 8:36 PM > > > > > Subject: RE: [PATCH V2 2/9] ARM: imx: Select MXC_CLK for ARCH_MXC > > > > > > > From: Anson Huang <Anson.Huang@nxp.com> > > > > Sent: Tuesday, June 9, 2020 3:32 PM > > > > > > > > i.MX common clock drivers may support module build, so it is NOT > > > > selected by default, for ARCH_MXC ARMv7 platforms, need to select > > > > it manually to make build pass. > > > > > > > > Signed-off-by: Anson Huang <Anson.Huang@nxp.com> > > > > > > Can't the original def_xxx work? > > > > > > config MXC_CLK > > > tristate > > > def_tristate ARCH_MXC > > > > Such change will make MXC_CLK=y even all i.MX8 SoCs clock drivers are > > selected as module, so it does NOT meet the requirement of module > > support. Below is from .config when all > > i.MX8 SoCs clock drivers are configured to module. > > > > CONFIG_MXC_CLK=y > > CONFIG_MXC_CLK_SCU=m > > CONFIG_CLK_IMX8MM=m > > CONFIG_CLK_IMX8MN=m > > CONFIG_CLK_IMX8MP=m > > CONFIG_CLK_IMX8MQ=m > > CONFIG_CLK_IMX8QXP=m > > > > It works at my side. > Below is my changes based on your patchset: > $ git diff > diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig index > 47b10d20f411..e7d7b90e2cf8 100644 > --- a/arch/arm/mach-imx/Kconfig > +++ b/arch/arm/mach-imx/Kconfig > @@ -4,7 +4,6 @@ menuconfig ARCH_MXC > depends on ARCH_MULTI_V4_V5 || ARCH_MULTI_V6_V7 || > ARM_SINGLE_ARMV7M > select ARCH_SUPPORTS_BIG_ENDIAN > select CLKSRC_IMX_GPT > - select MXC_CLK > select GENERIC_IRQ_CHIP > select GPIOLIB > select PINCTRL > diff --git a/drivers/clk/imx/Kconfig b/drivers/clk/imx/Kconfig index > 26cedbfe386c..f7b3e3a2cb9f 100644 > --- a/drivers/clk/imx/Kconfig > +++ b/drivers/clk/imx/Kconfig > @@ -3,6 +3,7 @@ > config MXC_CLK > tristate "IMX clock" > depends on ARCH_MXC > + def_tristate ARCH_MXC > > config MXC_CLK_SCU > tristate "IMX SCU clock" > I guess you tried imx_v6_v7_defconfig? It does NOT work for ARM64 defconfig when we try to make CONFIG_MXC_CLK=m, Below are my change, you can see in .config, even all i.MX8 SoCs clock drivers are configured to module, the CONFIG_MXC_CLK is still =y, but the expected result is =m. BTW, all i.MX8 SoCs select MXC_CLK in their kconfig, this patch just does the same thing for i.MX6/7 in common place. diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig index 47b10d2..e7d7b90 100644 --- a/arch/arm/mach-imx/Kconfig +++ b/arch/arm/mach-imx/Kconfig @@ -4,7 +4,6 @@ menuconfig ARCH_MXC depends on ARCH_MULTI_V4_V5 || ARCH_MULTI_V6_V7 || ARM_SINGLE_ARMV7M select ARCH_SUPPORTS_BIG_ENDIAN select CLKSRC_IMX_GPT - select MXC_CLK select GENERIC_IRQ_CHIP select GPIOLIB select PINCTRL diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index 8222e4b..21e2dbb 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -799,11 +799,11 @@ CONFIG_COMMON_CLK_S2MPS11=y CONFIG_COMMON_CLK_PWM=y CONFIG_COMMON_CLK_VC5=y CONFIG_CLK_RASPBERRYPI=m -CONFIG_CLK_IMX8MM=y -CONFIG_CLK_IMX8MN=y -CONFIG_CLK_IMX8MP=y -CONFIG_CLK_IMX8MQ=y -CONFIG_CLK_IMX8QXP=y +CONFIG_CLK_IMX8MM=m +CONFIG_CLK_IMX8MN=m +CONFIG_CLK_IMX8MP=m +CONFIG_CLK_IMX8MQ=m +CONFIG_CLK_IMX8QXP=m CONFIG_TI_SCI_CLK=y CONFIG_COMMON_CLK_QCOM=y CONFIG_QCOM_A53PLL=y diff --git a/drivers/clk/imx/Kconfig b/drivers/clk/imx/Kconfig index 26cedbf..f7b3e3a 100644 --- a/drivers/clk/imx/Kconfig +++ b/drivers/clk/imx/Kconfig @@ -3,6 +3,7 @@ config MXC_CLK tristate "IMX clock" depends on ARCH_MXC + def_tristate ARCH_MXC config MXC_CLK_SCU tristate "IMX SCU clock" .config: CONFIG_MXC_CLK=y CONFIG_MXC_CLK_SCU=m CONFIG_CLK_IMX8MM=m CONFIG_CLK_IMX8MN=m CONFIG_CLK_IMX8MP=m CONFIG_CLK_IMX8MQ=m CONFIG_CLK_IMX8QXP=m Anson
> From: Anson Huang <anson.huang@nxp.com> > Sent: Thursday, June 18, 2020 11:18 AM > > > From: Aisheng Dong <aisheng.dong@nxp.com> > > Sent: 2020年6月18日 11:09 > > > > > From: Anson Huang <anson.huang@nxp.com> > > > Sent: Wednesday, June 17, 2020 8:36 PM > > > > > > > Subject: RE: [PATCH V2 2/9] ARM: imx: Select MXC_CLK for ARCH_MXC > > > > > > > > > From: Anson Huang <Anson.Huang@nxp.com> > > > > > Sent: Tuesday, June 9, 2020 3:32 PM > > > > > > > > > > i.MX common clock drivers may support module build, so it is NOT > > > > > selected by default, for ARCH_MXC ARMv7 platforms, need to > > > > > select it manually to make build pass. > > > > > > > > > > Signed-off-by: Anson Huang <Anson.Huang@nxp.com> > > > > > > > > Can't the original def_xxx work? > > > > > > > > config MXC_CLK > > > > tristate > > > > def_tristate ARCH_MXC > > > > > > Such change will make MXC_CLK=y even all i.MX8 SoCs clock drivers > > > are selected as module, so it does NOT meet the requirement of > > > module support. Below is from .config when all > > > i.MX8 SoCs clock drivers are configured to module. > > > > > > CONFIG_MXC_CLK=y > > > CONFIG_MXC_CLK_SCU=m > > > CONFIG_CLK_IMX8MM=m > > > CONFIG_CLK_IMX8MN=m > > > CONFIG_CLK_IMX8MP=m > > > CONFIG_CLK_IMX8MQ=m > > > CONFIG_CLK_IMX8QXP=m > > > > > > > It works at my side. > > Below is my changes based on your patchset: > > $ git diff > > diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig > > index > > 47b10d20f411..e7d7b90e2cf8 100644 > > --- a/arch/arm/mach-imx/Kconfig > > +++ b/arch/arm/mach-imx/Kconfig > > @@ -4,7 +4,6 @@ menuconfig ARCH_MXC > > depends on ARCH_MULTI_V4_V5 || ARCH_MULTI_V6_V7 || > > ARM_SINGLE_ARMV7M > > select ARCH_SUPPORTS_BIG_ENDIAN > > select CLKSRC_IMX_GPT > > - select MXC_CLK > > select GENERIC_IRQ_CHIP > > select GPIOLIB > > select PINCTRL > > diff --git a/drivers/clk/imx/Kconfig b/drivers/clk/imx/Kconfig index > > 26cedbfe386c..f7b3e3a2cb9f 100644 > > --- a/drivers/clk/imx/Kconfig > > +++ b/drivers/clk/imx/Kconfig > > @@ -3,6 +3,7 @@ > > config MXC_CLK > > tristate "IMX clock" > > depends on ARCH_MXC > > + def_tristate ARCH_MXC > > > > config MXC_CLK_SCU > > tristate "IMX SCU clock" > > > > I guess you tried imx_v6_v7_defconfig? It does NOT work for ARM64 defconfig > when we try to make CONFIG_MXC_CLK=m, Below are my change, you can see > in .config, even all i.MX8 SoCs clock drivers are configured to module, the > CONFIG_MXC_CLK is still =y, but the expected result is =m. > It works at my side because it can manually selected as m or add CONFIG_MXC_CLK=m In defconfig. But now I got your point you want CONFIG_MXC_CLK default to m once define CONFIG_CLK_IMX8X=m in defconfig. > BTW, all i.MX8 SoCs select MXC_CLK in their kconfig, this patch just does the > same thing for i.MX6/7 in common place. > I just noticed for MX6&7, actually CONFIG_MXC_CLK can't be m otherwise we will meet build break. That means CONFIG_MXC_CLK cannot be configurable by users for non-ARM64 platforms. Thus can't use def_tristate and we still need select it under ARCH_MXC. This lightly lose a bit meaning to make this core library as module. IMHO I'd still prefer to builtin those core libraries rather than convert to module. Regards Aisheng > diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig index > 47b10d2..e7d7b90 100644 > --- a/arch/arm/mach-imx/Kconfig > +++ b/arch/arm/mach-imx/Kconfig > @@ -4,7 +4,6 @@ menuconfig ARCH_MXC > depends on ARCH_MULTI_V4_V5 || ARCH_MULTI_V6_V7 || > ARM_SINGLE_ARMV7M > select ARCH_SUPPORTS_BIG_ENDIAN > select CLKSRC_IMX_GPT > - select MXC_CLK > select GENERIC_IRQ_CHIP > select GPIOLIB > select PINCTRL > diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index > 8222e4b..21e2dbb 100644 > --- a/arch/arm64/configs/defconfig > +++ b/arch/arm64/configs/defconfig > @@ -799,11 +799,11 @@ CONFIG_COMMON_CLK_S2MPS11=y > CONFIG_COMMON_CLK_PWM=y CONFIG_COMMON_CLK_VC5=y > CONFIG_CLK_RASPBERRYPI=m -CONFIG_CLK_IMX8MM=y > -CONFIG_CLK_IMX8MN=y -CONFIG_CLK_IMX8MP=y -CONFIG_CLK_IMX8MQ=y > -CONFIG_CLK_IMX8QXP=y > +CONFIG_CLK_IMX8MM=m > +CONFIG_CLK_IMX8MN=m > +CONFIG_CLK_IMX8MP=m > +CONFIG_CLK_IMX8MQ=m > +CONFIG_CLK_IMX8QXP=m > CONFIG_TI_SCI_CLK=y > CONFIG_COMMON_CLK_QCOM=y > CONFIG_QCOM_A53PLL=y > diff --git a/drivers/clk/imx/Kconfig b/drivers/clk/imx/Kconfig index > 26cedbf..f7b3e3a 100644 > --- a/drivers/clk/imx/Kconfig > +++ b/drivers/clk/imx/Kconfig > @@ -3,6 +3,7 @@ > config MXC_CLK > tristate "IMX clock" > depends on ARCH_MXC > + def_tristate ARCH_MXC > > config MXC_CLK_SCU > tristate "IMX SCU clock" > > .config: > CONFIG_MXC_CLK=y > CONFIG_MXC_CLK_SCU=m > CONFIG_CLK_IMX8MM=m > CONFIG_CLK_IMX8MN=m > CONFIG_CLK_IMX8MP=m > CONFIG_CLK_IMX8MQ=m > CONFIG_CLK_IMX8QXP=m > > Anson
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig index e7d7b90..47b10d2 100644 --- a/arch/arm/mach-imx/Kconfig +++ b/arch/arm/mach-imx/Kconfig @@ -4,6 +4,7 @@ menuconfig ARCH_MXC depends on ARCH_MULTI_V4_V5 || ARCH_MULTI_V6_V7 || ARM_SINGLE_ARMV7M select ARCH_SUPPORTS_BIG_ENDIAN select CLKSRC_IMX_GPT + select MXC_CLK select GENERIC_IRQ_CHIP select GPIOLIB select PINCTRL
i.MX common clock drivers may support module build, so it is NOT selected by default, for ARCH_MXC ARMv7 platforms, need to select it manually to make build pass. Signed-off-by: Anson Huang <Anson.Huang@nxp.com> --- No change. --- arch/arm/mach-imx/Kconfig | 1 + 1 file changed, 1 insertion(+)