diff mbox

[08/11] ARM: dts: sun8i: a83t: Add MMC controller device nodes

Message ID 20170714064302.20383-9-wens@csie.org (mailing list archive)
State Superseded
Headers show

Commit Message

Chen-Yu Tsai July 14, 2017, 6:42 a.m. UTC 
The A83T has 3 MMC controllers. The third one is a bit special, as it
supports a wider 8-bit bus, and a "new timing mode".

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
 arch/arm/boot/dts/sun8i-a83t.dtsi | 57 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 57 insertions(+)

Comments

Maxime Ripard July 17, 2017, 9:22 a.m. UTC | #1 
Hi,

On Fri, Jul 14, 2017 at 02:42:59PM +0800, Chen-Yu Tsai wrote:
> The A83T has 3 MMC controllers. The third one is a bit special, as it
> supports a wider 8-bit bus, and a "new timing mode".
> 
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> ---
>  arch/arm/boot/dts/sun8i-a83t.dtsi | 57 +++++++++++++++++++++++++++++++++++++++
>  1 file changed, 57 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
> index beed05e10a3b..085312d0c521 100644
> --- a/arch/arm/boot/dts/sun8i-a83t.dtsi
> +++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
> @@ -182,6 +182,63 @@
>  			#dma-cells = <1>;
>  		};
>  
> +		mmc0: mmc@1c0f000 {
> +			compatible = "allwinner,sun7i-a20-mmc";

Ideally, we should have an A83T compatible here too, just in case.

Thanks!
Maxime
diff mbox

Patch

diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi
index beed05e10a3b..085312d0c521 100644
--- a/arch/arm/boot/dts/sun8i-a83t.dtsi
+++ b/arch/arm/boot/dts/sun8i-a83t.dtsi
@@ -182,6 +182,63 @@ 
 			#dma-cells = <1>;
 		};
 
+		mmc0: mmc@1c0f000 {
+			compatible = "allwinner,sun7i-a20-mmc";
+			reg = <0x01c0f000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC0>,
+				 <&ccu CLK_MMC0>,
+				 <&ccu CLK_MMC0_OUTPUT>,
+				 <&ccu CLK_MMC0_SAMPLE>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ccu RST_BUS_MMC0>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc@1c10000 {
+			compatible = "allwinner,sun7i-a20-mmc";
+			reg = <0x01c10000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC1>,
+				 <&ccu CLK_MMC1>,
+				 <&ccu CLK_MMC1_OUTPUT>,
+				 <&ccu CLK_MMC1_SAMPLE>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ccu RST_BUS_MMC1>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc2: mmc@1c11000 {
+			compatible = "allwinner,sun8i-a83t-emmc";
+			reg = <0x01c11000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC2>,
+				 <&ccu CLK_MMC2>,
+				 <&ccu CLK_MMC2_OUTPUT>,
+				 <&ccu CLK_MMC2_SAMPLE>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ccu RST_BUS_MMC2>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
 		ccu: clock@1c20000 {
 			compatible = "allwinner,sun8i-a83t-ccu";
 			reg = <0x01c20000 0x400>;