From patchwork Fri Mar 6 13:00:45 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Serge Semin X-Patchwork-Id: 11423859 Return-Path: Received: from mail.kernel.org (pdx-korg-mail-1.web.codeaurora.org [172.30.200.123]) by pdx-korg-patchwork-2.web.codeaurora.org (Postfix) with ESMTP id 5C5EB921 for ; Fri, 6 Mar 2020 13:08:03 +0000 (UTC) Received: from vger.kernel.org (vger.kernel.org [209.132.180.67]) by mail.kernel.org (Postfix) with ESMTP id 3E92C222C3 for ; Fri, 6 Mar 2020 13:08:03 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1726702AbgCFNIC (ORCPT ); Fri, 6 Mar 2020 08:08:02 -0500 Received: from mail.baikalelectronics.com ([87.245.175.226]:36436 "EHLO mail.baikalelectronics.ru" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1726314AbgCFNIC (ORCPT ); Fri, 6 Mar 2020 08:08:02 -0500 Received: from localhost (unknown [127.0.0.1]) by mail.baikalelectronics.ru (Postfix) with ESMTP id 7F70E8030793; Fri, 6 Mar 2020 13:00:55 +0000 (UTC) X-Virus-Scanned: amavisd-new at baikalelectronics.ru Received: from mail.baikalelectronics.ru ([127.0.0.1]) by localhost (mail.baikalelectronics.ru [127.0.0.1]) (amavisd-new, port 10024) with ESMTP id AM2kRPbb_J9F; Fri, 6 Mar 2020 16:00:54 +0300 (MSK) From: To: Michael Turquette , Stephen Boyd , Rob Herring , Mark Rutland , Philipp Zabel CC: Serge Semin , Serge Semin , Alexey Malahov , Thomas Bogendoerfer , Paul Burton , Ralf Baechle , , , Subject: [PATCH 2/5] dt-bindings: clk: Add Baikal-T1 AXI-bus CCU bindings Date: Fri, 6 Mar 2020 16:00:45 +0300 In-Reply-To: <20200306130048.8868-1-Sergey.Semin@baikalelectronics.ru> References: <20200306130048.8868-1-Sergey.Semin@baikalelectronics.ru> MIME-Version: 1.0 X-ClientProxiedBy: MAIL.baikal.int (192.168.51.25) To mail (192.168.51.25) Message-Id: <20200306130055.7F70E8030793@mail.baikalelectronics.ru> Sender: linux-clk-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-clk@vger.kernel.org From: Serge Semin After being gained by the CCU PLLs the signals must be transformed to be suitable for the clock-consumers. This is done by a set of dividers embedded into the CCU. A first block of dividers is used to create reference clocks for AXI-bus of high-speed peripheral IP-cores of the chip. So the AXI-bus CCU dts-node is an ordinary clock-provider with standard set of properties supported. But in addition to that each AXI-bus clock divider provide a way to reset the corresponding clock domain. This makes the AXI-bus CCU dts-node to be also a reset-provider. Signed-off-by: Serge Semin Signed-off-by: Alexey Malahov Cc: Thomas Bogendoerfer Cc: Paul Burton Cc: Ralf Baechle --- .../bindings/clock/be,bt1-ccu-axi.yaml | 151 ++++++++++++++++++ include/dt-bindings/clock/bt1-ccu.h | 13 ++ include/dt-bindings/reset/bt1-ccu.h | 23 +++ 3 files changed, 187 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/be,bt1-ccu-axi.yaml create mode 100644 include/dt-bindings/reset/bt1-ccu.h diff --git a/Documentation/devicetree/bindings/clock/be,bt1-ccu-axi.yaml b/Documentation/devicetree/bindings/clock/be,bt1-ccu-axi.yaml new file mode 100644 index 000000000000..6b1eefdead27 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/be,bt1-ccu-axi.yaml @@ -0,0 +1,151 @@ +# SPDX-License-Identifier: GPL-2.0 +# +# Copyright (C) 2019 - 2020 BAIKAL ELECTRONICS, JSC +# +# Baikal-T1 AXI-bus Clocks Control Unit Device Tree Bindings. +# +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/be,bt1-ccu-axi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Baikal-T1 AXI-bus Clock Control Unit + +maintainers: + - Serge Semin + +description: | + Clocks Control Unit is the core of Baikal-T1 SoC responsible for the chip + subsystems clocking and resetting. The CCU is connected with an external + fixed rate oscillator, which signal is transformed into clocks of various + frequencies and then propagated to either individual IP-blocks or to groups + of blocks (clock domains). The transformation is done by means of an embedded + into CCU PLLs and gateable/non-gateable dividers. Each clock domain can be + also individually reset by using the domain clocks divider configuration + registers. Baikal-T1 CCU is logically divided into the next components: + 1) External oscillator (normally XTAL's 25 MHz crystal oscillator, but + in general can provide any frequency supported by the CCU PLLs). + 2) PLLs clocks generators (PLLs). + 3) AXI-bus clock dividers (AXI) - described in this bindings file. + 4) System devices reference clock dividers (SYS). + which are connected with each other as shown on the next figure: + +---------------+ + | Baikal-T1 CCU | + | +----+------|- MIPS P5600 cores + | +-|PLLs|------|- DDR controller + | | +----+ | + +----+ | | | | | + |XTAL|--|-+ | | +---+-| + +----+ | | | +-|AXI|-|- AXI-bus + | | | +---+-| + | | | | + | | +----+---+-|- APB-bus + | +-------|SYS|-|- Low-speed Devices + | +---+-|- High-speed Devices + +---------------+ + Each sub-block is represented as a separate dts-node and has an individual + driver to be bound with. + + In order to create signals of wide range frequencies the external oscillator + output is primarily connected to a set of CCU PLLs. Some of PLLs CLKOUT are + then passed over CCU dividers to create signals required for the target clock + domain (like AXI-bus consumers). The dividers have the following structure: + +--------------+ + CLKIN --|->+----+ 1|\ | + SETCLK--|--|/DIV|->| | | + CLKDIV--|--| | | |-|->CLKLOUT + LOCK----|--+----+ | | | + | |/ | + | | | + EN------|-----------+ | + RST-----|--------------|->RSTOUT + +--------------+ + where CLKIN is the reference clock coming either from a CCU PLL, SETCLK - a + command to update the output clock in accordance with a set divider, + CLKDIV - clocks divider, LOCK - a signal of the output clock stabilization, + EN - enable/disable the divider block, RST/RSTOUT - reset clocks domain + signal. Depending on the consumer IP-core peculiarities the dividers may lack + of some functionality depicted on the figure above (like EN, + CLKDIV/LOCK/SETCLK). In this case the corresponding clock provider just + doesn't expose either switching functions, or the rate configuration, or + both of them. + + The CCU AXI dts-node uses the common clock bindings [1] with no custom + properties. The list of exported clocks and reset signals can be found in + the files: 'dt-bindings/clock/bt1-ccu.h' and 'dt-bindings/reset/bt1-ccu.h'. + + [1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +allOf: + - $ref: /schemas/clock/clock.yaml# + +properties: + compatible: + const: be,bt1-ccu-axi + + reg: + description: AXI-bus CCU dividers sub-block base address. + maxItems: 1 + + "#clock-cells": + description: | + Clocks are referenced by the node phandle and an unique identifier + from 'dt-bindings/clock/bt1-ccu.h'. + const: 1 + + "#reset-cells": + description: | + AXI-bus CCU sub-block provides a reset signal for each clock domain, + which unique identifiers are in 'dt-bindings/reset/bt1-ccu.h'. + const: 1 + + clocks: + items: + - description: CCU SATA PLL output clock. + - description: CCU PCIe PLL output clock. + - description: CCU Ethernet PLL output clock. + + clock-names: + items: + - const: sata_clk + - const: pcie_clk + - const: eth_clk + + clock-output-names: true + + assigned-clocks: true + + assigned-clock-rates: true + +additionalProperties: false + +required: + - compatible + - reg + - "#clock-cells" + - clocks + - clock-names + +examples: + - | + #include + + ccu_axi: ccu_axi@1F04D030 { + compatible = "be,bt1-ccu-axi"; + reg = <0x1F04D030 0x030>; + #clock-cells = <1>; + #reset-cells = <1>; + + clocks = <&ccu_pll CCU_SATA_PLL>, + <&ccu_pll CCU_PCIE_PLL>, + <&ccu_pll CCU_ETH_PLL>; + clock-names = "sata_clk", "pcie_clk", "eth_clk"; + + clock-output-names = "axi_main_clk", "axi_ddr_clk", + "axi_sata_clk", "axi_gmac0_clk", + "axi_gmac1_clk", "axi_xgmac_clk", + "axi_pcie_m_clk", "axi_pcie_s_clk", + "axi_usb_clk", "axi_hwa_clk", + "axi_sram_clk"; + }; +... diff --git a/include/dt-bindings/clock/bt1-ccu.h b/include/dt-bindings/clock/bt1-ccu.h index 86e63162ade0..ebe723c6e0a8 100644 --- a/include/dt-bindings/clock/bt1-ccu.h +++ b/include/dt-bindings/clock/bt1-ccu.h @@ -14,4 +14,17 @@ #define CCU_PCIE_PLL 3 #define CCU_ETH_PLL 4 +/* Baikal-T1 AXI-bus CCU Clocks indeces. */ +#define CCU_AXI_MAIN_CLK 0 +#define CCU_AXI_DDR_CLK 1 +#define CCU_AXI_SATA_CLK 2 +#define CCU_AXI_GMAC0_CLK 3 +#define CCU_AXI_GMAC1_CLK 4 +#define CCU_AXI_XGMAC_CLK 5 +#define CCU_AXI_PCIE_M_CLK 6 +#define CCU_AXI_PCIE_S_CLK 7 +#define CCU_AXI_USB_CLK 8 +#define CCU_AXI_HWA_CLK 9 +#define CCU_AXI_SRAM_CLK 10 + #endif /* __DT_BINDINGS_CLOCK_BT1_CCU_H */ diff --git a/include/dt-bindings/reset/bt1-ccu.h b/include/dt-bindings/reset/bt1-ccu.h new file mode 100644 index 000000000000..4de5b6bcd433 --- /dev/null +++ b/include/dt-bindings/reset/bt1-ccu.h @@ -0,0 +1,23 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * Copyright (C) 2019 BAIKAL ELECTRONICS, JSC + * + * Baikal-T1 CCU reset indeces. + */ +#ifndef __DT_BINDINGS_RESET_BT1_CCU_H +#define __DT_BINDINGS_RESET_BT1_CCU_H + +/* Baikal-T1 AXI-bus CCU Reset indeces. */ +#define CCU_AXI_MAIN_RST 0 +#define CCU_AXI_DDR_RST 1 +#define CCU_AXI_SATA_RST 2 +#define CCU_AXI_GMAC0_RST 3 +#define CCU_AXI_GMAC1_RST 4 +#define CCU_AXI_XGMAC_RST 5 +#define CCU_AXI_PCIE_M_RST 6 +#define CCU_AXI_PCIE_S_RST 7 +#define CCU_AXI_USB_RST 8 +#define CCU_AXI_HWA_RST 9 +#define CCU_AXI_SRAM_RST 10 + +#endif /* __DT_BINDINGS_RESET_BT1_CCU_H */