diff mbox

[16/24] davinci: dm365: add MMC/SD support

Message ID 1247868758-10423-17-git-send-email-khilman@deeprootsystems.com (mailing list archive)
State Awaiting Upstream
Headers show

Commit Message

Kevin Hilman July 17, 2009, 10:12 p.m. UTC 
From: Sandeep Paulraj <s-paulraj@ti.com>

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
---
 arch/arm/mach-davinci/devices.c |   45 ++++++++++++++++++++++++++------------
 1 files changed, 31 insertions(+), 14 deletions(-)
diff mbox

Patch

diff --git a/arch/arm/mach-davinci/devices.c b/arch/arm/mach-davinci/devices.c
index 385e833..a55b650 100644
--- a/arch/arm/mach-davinci/devices.c
+++ b/arch/arm/mach-davinci/devices.c
@@ -31,6 +31,8 @@ 
 #define DAVINCI_MMCSD0_BASE	     0x01E10000
 #define DM355_MMCSD0_BASE	     0x01E11000
 #define DM355_MMCSD1_BASE	     0x01E00000
+#define DM365_MMCSD0_BASE	     0x01D11000
+#define DM365_MMCSD1_BASE	     0x01D00000
 
 static struct resource i2c_resources[] = {
 	{
@@ -154,19 +156,31 @@  void __init davinci_setup_mmc(int module, struct davinci_mmc_config *config)
 	 */
 	switch (module) {
 	case 1:
-		if (!cpu_is_davinci_dm355())
+		if (cpu_is_davinci_dm355()) {
+			/* REVISIT we may not need all these pins if e.g. this
+			 * is a hard-wired SDIO device...
+			 */
+			davinci_cfg_reg(DM355_SD1_CMD);
+			davinci_cfg_reg(DM355_SD1_CLK);
+			davinci_cfg_reg(DM355_SD1_DATA0);
+			davinci_cfg_reg(DM355_SD1_DATA1);
+			davinci_cfg_reg(DM355_SD1_DATA2);
+			davinci_cfg_reg(DM355_SD1_DATA3);
+		} else if (cpu_is_davinci_dm365()) {
+			void __iomem *pupdctl1 =
+				IO_ADDRESS(DAVINCI_SYSTEM_MODULE_BASE + 0x7c);
+
+			/* Configure pull down control */
+			__raw_writel((__raw_readl(pupdctl1) & ~0x400),
+					pupdctl1);
+
+			mmcsd1_resources[0].start = DM365_MMCSD1_BASE;
+			mmcsd1_resources[0].end = DM365_MMCSD1_BASE +
+							SZ_4K - 1;
+			mmcsd0_resources[2].start = IRQ_DM365_SDIOINT1;
+		} else
 			break;
 
-		/* REVISIT we may not need all these pins if e.g. this
-		 * is a hard-wired SDIO device...
-		 */
-		davinci_cfg_reg(DM355_SD1_CMD);
-		davinci_cfg_reg(DM355_SD1_CLK);
-		davinci_cfg_reg(DM355_SD1_DATA0);
-		davinci_cfg_reg(DM355_SD1_DATA1);
-		davinci_cfg_reg(DM355_SD1_DATA2);
-		davinci_cfg_reg(DM355_SD1_DATA3);
-
 		pdev = &davinci_mmcsd1_device;
 		break;
 	case 0:
@@ -180,9 +194,12 @@  void __init davinci_setup_mmc(int module, struct davinci_mmc_config *config)
 
 			/* enable RX EDMA */
 			davinci_cfg_reg(DM355_EVT26_MMC0_RX);
-		}
-
-		else if (cpu_is_davinci_dm644x()) {
+		} else if (cpu_is_davinci_dm365()) {
+			mmcsd0_resources[0].start = DM365_MMCSD0_BASE;
+			mmcsd0_resources[0].end = DM365_MMCSD0_BASE +
+							SZ_4K - 1;
+			mmcsd0_resources[2].start = IRQ_DM365_SDIOINT0;
+		} else if (cpu_is_davinci_dm644x()) {
 			/* REVISIT: should this be in board-init code? */
 			void __iomem *base =
 				IO_ADDRESS(DAVINCI_SYSTEM_MODULE_BASE);