new file mode 100644
@@ -0,0 +1,82 @@
+* STMicroelectronics STM32 DMA controller
+
+The STM32 DMA is a general-purpose direct memory access controller capable of
+supporting 8 independent DMA channels. Each channel can have up to 8 requests.
+
+Required properties:
+- compatible: Should be "st,stm32-dma"
+- reg: Should contain DMA registers location and length. This should include
+ all of the per-channel registers.
+- interrupts: Should contain all of the per-channel DMA interrupts ordering by
+ channel index.
+- clocks: Should contain the input clock of the DMA instance.
+- #dma-cells : Must be <4>. See DMA client paragraph for more details.
+
+Optional properties:
+- resets: Reference to a reset controller asserting the DMA controller
+- st,mem2mem: boolean; if defined, it indicates that the controller supports
+ memory-to-memory transfer
+
+Example:
+
+ dma2: dma-controller@40026400 {
+ compatible = "st,stm32-dma";
+ reg = <0x40026400 0x400>;
+ interrupts = <56>,
+ <57>,
+ <58>,
+ <59>,
+ <60>,
+ <68>,
+ <69>,
+ <70>;
+ clocks = <&clk_hclk>;
+ #dma-cells = <4>;
+ st,mem2mem;
+ resets = <&rcc 150>;
+ };
+
+* DMA client
+
+DMA clients connected to the STM32 DMA controller must use the format
+described in the dma.txt file, using a five-cell specifier for each
+channel: a phandle plus four integer cells.
+The four cells in order are:
+
+1. The channel id
+2. The request line number
+3. A 32bit mask specifying the DMA channel configuration which are device
+ dependent:
+ -bit 9: Peripheral Increment Address
+ 0x0: no address increment between transfers
+ 0x1: increment address between transfers
+ -bit 10: Memory Increment Address
+ 0x0: no address increment between transfers
+ 0x1: increment address between transfers
+ -bit 15: Peripheral Increment Offset Size
+ 0x0: offset size is linked to the peripheral bus width
+ 0x1: offset size is fixed to 4 (32-bit alignment)
+ -bit 16-17: Priority level
+ 0x0: low
+ 0x1: medium
+ 0x2: high
+ 0x3: very high
+5. A 32bit mask specifying the DMA FIFO threshold configuration which are device
+ dependent:
+ -bit 0-1: Fifo threshold
+ 0x0: 1/4 full FIFO
+ 0x1: 1/2 full FIFO
+ 0x2: 3/4 full FIFO
+ 0x3: full FIFO
+
+Example:
+
+ usart1: serial@40011000 {
+ compatible = "st,stm32-usart", "st,stm32-uart";
+ reg = <0x40011000 0x400>;
+ interrupts = <37>;
+ clocks = <&clk_pclk2>;
+ dmas = <&dma2 2 4 0x10400 0x3>,
+ <&dma2 7 5 0x10200 0x3>;
+ dma-names = "rx", "tx";
+ };
This patch adds documentation of device tree bindings for the STM32 dma controller. Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com> --- .../devicetree/bindings/dma/stm32-dma.txt | 82 ++++++++++++++++++++++ 1 file changed, 82 insertions(+) create mode 100644 Documentation/devicetree/bindings/dma/stm32-dma.txt