@@ -28,7 +28,7 @@ obj-$(CONFIG_BACKLIGHT_OMAP1) += omap1_bl.o
obj-$(CONFIG_BACKLIGHT_PANDORA) += pandora_bl.o
obj-$(CONFIG_BACKLIGHT_PROGEAR) += progear_bl.o
obj-$(CONFIG_BACKLIGHT_CARILLO_RANCH) += cr_bllcd.o
-obj-$(CONFIG_BACKLIGHT_PWM) += pwm_bl.o
+obj-$(CONFIG_BACKLIGHT_PWM) += pwm_bl.o power_seq.o
obj-$(CONFIG_BACKLIGHT_DA903X) += da903x_bl.o
obj-$(CONFIG_BACKLIGHT_DA9052) += da9052_bl.o
obj-$(CONFIG_BACKLIGHT_MAX8925) += max8925_bl.o
new file mode 100644
@@ -0,0 +1,298 @@
+#include <linux/err.h>
+#include <linux/of_gpio.h>
+#include <linux/device.h>
+#include <linux/slab.h>
+#include <linux/power_seq.h>
+#include <linux/delay.h>
+#include <linux/pwm.h>
+#include <linux/regulator/consumer.h>
+
+#define PWM_SEQ_TYPE(type) [POWER_SEQ_ ## type] = #type
+static const char *pwm_seq_types[] = {
+ PWM_SEQ_TYPE(STOP),
+ PWM_SEQ_TYPE(DELAY),
+ PWM_SEQ_TYPE(REGULATOR),
+ PWM_SEQ_TYPE(PWM),
+ PWM_SEQ_TYPE(GPIO),
+};
+#undef PWM_SEQ_TYPE
+
+static bool power_seq_step_run(struct power_seq_step *step)
+{
+ switch (step->type) {
+ case POWER_SEQ_DELAY:
+ msleep(step->parameter);
+ break;
+ case POWER_SEQ_REGULATOR:
+ if (step->parameter)
+ regulator_enable(step->resource->regulator);
+ else
+ regulator_disable(step->resource->regulator);
+ break;
+ case POWER_SEQ_PWM:
+ if (step->parameter)
+ pwm_enable(step->resource->pwm);
+ else
+ pwm_disable(step->resource->pwm);
+ break;
+ case POWER_SEQ_GPIO:
+ gpio_set_value_cansleep(step->resource->gpio, step->parameter);
+ break;
+ /* should never happen since we verify the data when building it */
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+int power_seq_run(power_seq *seq)
+{
+ int err;
+
+ if (!seq) return 0;
+
+ while (seq->type != POWER_SEQ_STOP) {
+ if ((err = power_seq_step_run(seq++))) {
+ return err;
+ }
+ }
+
+ return 0;
+}
+
+static int of_parse_power_seq_step(struct device *dev, struct property *prop,
+ struct platform_power_seq_step *seq,
+ int max_steps)
+{
+ void *value = prop->value;
+ void *end = prop->value + prop->length;
+ int slen, smax, cpt = 0, i, ret;
+ char tmp_buf[32];
+
+ while (value < end && cpt < max_steps) {
+ smax = value - end;
+ slen = strnlen(value, end - value);
+
+ /* Unterminated string / not a string? */
+ if (slen >= end - value)
+ goto invalid_seq;
+
+ /* Find a matching sequence step type */
+ for (i = 0; i < POWER_SEQ_MAX; i++)
+ if (!strcmp(value, pwm_seq_types[i]))
+ break;
+
+ if (i >= POWER_SEQ_MAX)
+ goto unknown_step;
+
+ value += slen + 1;
+
+ seq[cpt].type = i;
+ switch (seq[cpt].type) {
+ case POWER_SEQ_DELAY:
+ /* integer parameter */
+ seq[cpt].parameter = be32_to_cpup(value);
+ value += sizeof(__be32);
+ break;
+ case POWER_SEQ_REGULATOR:
+ case POWER_SEQ_PWM:
+ case POWER_SEQ_GPIO:
+ /* consumer string */
+ slen = strnlen(value, end - value);
+ if (slen >= end - value)
+ goto invalid_seq;
+ seq[cpt].id = value;
+ value += slen + 1;
+
+ /* parameter */
+ seq[cpt].parameter = be32_to_cpup(value);
+ be32_to_cpup(value);
+ value += sizeof(__be32);
+
+ /* For GPIO we still need to resolve the phandle */
+ if (seq[cpt].type != POWER_SEQ_GPIO)
+ break;
+
+ strncpy(tmp_buf, seq[cpt].id, sizeof(tmp_buf) - 6);
+ tmp_buf[sizeof(tmp_buf) - 6] = 0;
+ strcat(tmp_buf, "-gpios");
+ ret = of_get_named_gpio(dev->of_node, tmp_buf, 0);
+ if (ret >= 0)
+ seq[cpt].value = ret;
+ else {
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "cannot get gpio \"%s\"\n",
+ seq[cpt].id);
+ return ret;
+ }
+ default:
+ break;
+ }
+
+ cpt++;
+ }
+
+ if (cpt >= max_steps)
+ return -EOVERFLOW;
+
+ return 0;
+
+invalid_seq:
+ dev_err(dev, "invalid sequence \"%s\"\n", prop->name);
+ return -EINVAL;
+unknown_step:
+ dev_err(dev, "unknown step type \"%s\" in sequence \"%s\"\n",
+ (char *)value, prop->name);
+ return -EINVAL;
+}
+
+#define PWM_SEQ_MAX_LENGTH 16
+platform_power_seq *of_parse_power_seq(struct device *dev,
+ struct device_node *node, char *propname)
+{
+ platform_power_seq *seq = NULL;
+ struct property *prop;
+ int length;
+ int ret;
+
+ prop = of_find_property(node, propname, &length);
+ if (prop && length > 0) {
+ seq = devm_kzalloc(dev, sizeof(*seq) * PWM_SEQ_MAX_LENGTH,
+ GFP_KERNEL);
+ if (!seq)
+ return ERR_PTR(-ENOMEM);
+ /* keep one empty entry for the STOP step */
+ ret = of_parse_power_seq_step(dev, prop, seq,
+ PWM_SEQ_MAX_LENGTH - 1);
+ if (ret < 0)
+ return ERR_PTR(ret);
+ }
+
+ return seq;
+}
+
+static
+struct power_seq_resource * power_seq_find_resource(power_seq_resources *ress,
+ struct platform_power_seq_step *res)
+{
+ struct power_seq_resource *step;
+
+ list_for_each_entry(step, ress, list) {
+ if (step->plat.type != res->type) continue;
+ switch (res->type) {
+ case POWER_SEQ_DELAY:
+ case POWER_SEQ_GPIO:
+ if (step->plat.value == res->value)
+ return step;
+ break;
+ default:
+ if (!strcmp(step->plat.id, res->id))
+ return step;
+ break;
+ }
+ }
+
+ return NULL;
+}
+
+power_seq *power_seq_build(struct device *dev, power_seq_resources *ress,
+ platform_power_seq *pseq)
+{
+ struct power_seq_step *seq = NULL, *ret;
+ struct power_seq_resource *res;
+ int cpt;
+
+ /* first pass to count the number of elements */
+ for (cpt = 0; pseq[cpt].type != POWER_SEQ_STOP; cpt++);
+
+ if (!cpt)
+ return seq;
+
+ /* 1 more for the STOP step */
+ ret = seq = devm_kzalloc(dev, sizeof(*seq) * (cpt + 1), GFP_KERNEL);
+ if (!seq)
+ return ERR_PTR(-ENOMEM);
+
+ for (; pseq->type != POWER_SEQ_STOP; pseq++, seq++) {
+ seq->type = pseq->type;
+
+ switch (pseq->type) {
+ case POWER_SEQ_REGULATOR:
+ case POWER_SEQ_GPIO:
+ case POWER_SEQ_PWM:
+ if (!(res = power_seq_find_resource(ress, pseq))) {
+ /* create resource node */
+ res = devm_kzalloc(dev, sizeof(*res),
+ GFP_KERNEL);
+ if (!res)
+ return ERR_PTR(-ENOMEM);
+ memcpy(&res->plat, pseq, sizeof(*pseq));
+
+ list_add(&res->list, ress);
+ }
+ seq->resource = res;
+ case POWER_SEQ_DELAY:
+ seq->parameter = pseq->parameter;
+ break;
+ default:
+ dev_err(dev, "invalid sequence step type!\n");
+ return ERR_PTR(-EINVAL);
+ }
+ }
+
+ return ret;
+}
+
+int power_seq_allocate_resources(struct device *dev, power_seq_resources *ress)
+{
+ struct power_seq_resource *res;
+ int err;
+
+ list_for_each_entry(res, ress, list) {
+ switch (res->plat.type) {
+ case POWER_SEQ_REGULATOR:
+ res->regulator = devm_regulator_get(dev, res->plat.id);
+ if (IS_ERR(res->regulator)) {
+ dev_err(dev, "cannot get regulator \"%s\"\n",
+ res->plat.id);
+ return PTR_ERR(res->regulator);
+ }
+ dev_dbg(dev, "got regulator %s\n", res->plat.id);
+ break;
+ case POWER_SEQ_PWM:
+ res->pwm = pwm_get(dev, res->plat.id);
+ if (IS_ERR(res->pwm)) {
+ dev_err(dev, "cannot get pwm \"%s\"\n",
+ res->plat.id);
+ return PTR_ERR(res->pwm);
+ }
+ dev_dbg(dev, "got PWM %s\n", res->plat.id);
+ break;
+ case POWER_SEQ_GPIO:
+ err = devm_gpio_request_one(dev, res->plat.value,
+ GPIOF_OUT_INIT_HIGH, "backlight_gpio");
+ if (err) {
+ dev_err(dev, "cannot get gpio %d\n",
+ res->plat.value);
+ return err;
+ }
+ res->gpio = res->plat.value;
+ dev_dbg(dev, "got GPIO %d\n", res->plat.value);
+ break;
+ default:
+ break;
+ };
+ }
+
+ return 0;
+}
+
+void power_seq_free_resources(power_seq_resources *ress) {
+ struct power_seq_resource *res;
+
+ list_for_each_entry(res, ress, list) {
+ if (res->plat.type == POWER_SEQ_PWM)
+ pwm_put(res->pwm);
+ }
+}
@@ -203,8 +203,9 @@ static int pwm_backlight_probe(struct platform_device *pdev)
if (data->levels) {
max = data->levels[data->max_brightness];
pb->levels = data->levels;
- } else
+ } else {
max = data->max_brightness;
+ }
pb->notify = data->notify;
pb->notify_after = data->notify_after;
new file mode 100644
@@ -0,0 +1,96 @@
+/*
+ * Simple interpreter for defining power sequences as platform data or device
+ * tree properties. Mainly for use with backlight drivers.
+ */
+
+#ifndef __LINUX_POWER_SEQ_H
+#define __LINUX_POWER_SEQ_H
+
+#include <linux/of.h>
+#include <linux/types.h>
+
+/**
+ * The different kinds of resources that can be controlled during the sequences.
+ */
+typedef enum {
+ POWER_SEQ_STOP = 0,
+ POWER_SEQ_DELAY,
+ POWER_SEQ_REGULATOR,
+ POWER_SEQ_PWM,
+ POWER_SEQ_GPIO,
+ POWER_SEQ_MAX,
+} seq_type;
+
+/**
+ * Describe something to do during the power-up/down sequence.
+ */
+struct platform_power_seq_step {
+ seq_type type;
+ /**
+ * Identify the resource. Steps of type DELAY use value, others name the
+ * consumer to use in id.
+ */
+ union {
+ const char *id;
+ int value;
+ };
+ /**
+ * A value of 0 disables the resource, while a non-zero enables it.
+ * For DELAY steps this contains the delay to wait in milliseconds.
+ */
+ int parameter;
+};
+typedef struct platform_power_seq_step platform_power_seq;
+
+struct power_seq_resource {
+ /* copied from platform data */
+ struct platform_power_seq_step plat;
+ /* resolved resource */
+ union {
+ struct regulator *regulator;
+ struct pwm_device *pwm;
+ int gpio;
+ };
+ /* used to maintain a list of resources used by the driver */
+ struct list_head list;
+};
+typedef struct list_head power_seq_resources;
+
+struct power_seq_step {
+ seq_type type;
+ int parameter;
+ struct power_seq_resource *resource;
+};
+typedef struct power_seq_step power_seq;
+
+/**
+ * Build a platform data sequence from a device tree node. Memory for the
+ * sequence is allocated using devm_kzalloc on dev.
+ */
+platform_power_seq *of_parse_power_seq(struct device *dev,
+ struct device_node *node,
+ char *propname);
+/**
+ * Build a runnable power sequence from platform data, and add the resources
+ * it uses into ress. Memory for the sequence is allocated using devm_kzalloc
+ * on dev.
+ */
+power_seq *power_seq_build(struct device *dev, power_seq_resources *ress,
+ platform_power_seq *pseq);
+/**
+ * Allocate all resources (regulators, PWMs, GPIOs) found by calls to
+ * power_seq_build() for use by dev. Return 0 in case of success, error code
+ * otherwise.
+ */
+int power_seq_allocate_resources(struct device *dev, power_seq_resources *ress);
+/**
+ * Free all the resources previously allocated by power_seq_allocate_resources.
+ */
+void power_seq_free_resources(power_seq_resources *ress);
+/**
+ * Run the given power sequence. Returns 0 on success, error code in case of
+ * failure.
+ */
+int power_seq_run(power_seq *seq);
+
+#endif
Some device drivers (panel backlights especially) need to follow precise sequences for powering on and off, involving gpios, regulators, PWMs with a precise powering order and delays to respect between each steps. These sequences are board-specific, and do not belong to a particular driver - therefore they have been performed by board-specific hook functions to far. With the advent of the device tree, we cannot rely of board-specific hooks anymore, but still need a way to implement these sequences in a portable manner. This patch introduces a simple interpreter that can execute such power sequences encoded either as platform data or within the device tree. Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> --- drivers/video/backlight/Makefile | 2 +- drivers/video/backlight/power_seq.c | 298 ++++++++++++++++++++++++++++++++++++ drivers/video/backlight/pwm_bl.c | 3 +- include/linux/power_seq.h | 96 ++++++++++++ 4 files changed, 397 insertions(+), 2 deletions(-) create mode 100644 drivers/video/backlight/power_seq.c create mode 100644 include/linux/power_seq.h