| Message ID | 1343102984-6056-1-git-send-email-prakash.pm@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On Tue, Jul 24, 2012 at 9:39 AM, Manjunathappa, Prakash <prakash.pm@ti.com> wrote: > > Wait for active frame transfer to complete after disabling LCDC. > At the same this wait is not be required when there are sync and > underflow errors. > More information on disable and reset sequence can be found in > section 13.4.6 of AM335x TRM @www.ti.com/am335x. > > Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com> > --- > Patch applies on top of below patch under review: > http://marc.info/?l=linux-fbdev&m=134280060828708&w=2 > "video: da8xx-fb: do clock reset of revision 2 LCDC before enabling" > Since v1: > Changed the commit message, also added link to hardware specification. > > drivers/video/da8xx-fb.c | 48 > ++++++++++++++++++++++++++++++++++++--------- > 1 files changed, 38 insertions(+), 10 deletions(-) > > diff --git a/drivers/video/da8xx-fb.c b/drivers/video/da8xx-fb.c > index a908dfd..0fb4d7d 100644 > --- a/drivers/video/da8xx-fb.c > +++ b/drivers/video/da8xx-fb.c > @@ -31,6 +31,7 @@ > #include <linux/cpufreq.h> > #include <linux/console.h> > #include <linux/slab.h> > +#include <linux/delay.h> > #include <video/da8xx-fb.h> > #include <asm/div64.h> > > @@ -45,6 +46,7 @@ > #define LCD_PL_LOAD_DONE BIT(6) > #define LCD_FIFO_UNDERFLOW BIT(5) > #define LCD_SYNC_LOST BIT(2) > +#define LCD_FRAME_DONE BIT(0) > > /* LCD DMA Control Register */ > #define LCD_DMA_BURST_SIZE(x) ((x) << 4) > @@ -279,13 +281,39 @@ static inline void lcd_enable_raster(void) > } > > /* Disable the Raster Engine of the LCD Controller */ > -static inline void lcd_disable_raster(void) > +static inline void lcd_disable_raster(bool wait_for_frame_done) > { > u32 reg; > + u32 loop_cnt = 0; > + u32 stat; > + u32 i = 0; > + > + /* 50 milli seconds should be sufficient for a frame to complete > */ > + if (wait_for_frame_done) > + loop_cnt = 50; > > reg = lcdc_read(LCD_RASTER_CTRL_REG); > if (reg & LCD_RASTER_ENABLE) > lcdc_write(reg & ~LCD_RASTER_ENABLE, LCD_RASTER_CTRL_REG); > + > + /* Wait for the current frame to complete */ > + do { > + if (lcd_revision == LCD_VERSION_1) > + stat = lcdc_read(LCD_STAT_REG); > + else > + stat = lcdc_read(LCD_RAW_STAT_REG); > + mdelay(1); > + } while (!(stat & LCD_FRAME_DONE) && (i++ < loop_cnt)); Are you sure it should be do while? You call it from interrupt handler too (sync lost handling). In that case mdelay() from interrupt context..not a good idea I feel. > + > + if (lcd_revision == LCD_VERSION_1) > + lcdc_write(stat, LCD_STAT_REG); > + else > + lcdc_write(stat, LCD_MASKED_STAT_REG); > + > + if ((loop_cnt != 0) && (i >= loop_cnt)) { > + pr_err("LCD Controller timed out\n"); > + return; return may not be necessary? > + } > } > > static void lcd_blit(int load_mode, struct da8xx_fb_par *par) > @@ -626,7 +654,7 @@ static int fb_setcolreg(unsigned regno, unsigned red, > unsigned green, > static void lcd_reset(struct da8xx_fb_par *par) > { > /* Disable the Raster if previously Enabled */ > - lcd_disable_raster(); > + lcd_disable_raster(false); > > /* DMA has to be disabled */ > lcdc_write(0, LCD_DMA_CTRL_REG); > @@ -724,7 +752,7 @@ static irqreturn_t lcdc_irq_handler_rev02(int irq, > void *arg) > > if ((stat & LCD_SYNC_LOST) && (stat & LCD_FIFO_UNDERFLOW)) { > pr_err("LCDC sync lost or underflow error occurred\n"); > - lcd_disable_raster(); > + lcd_disable_raster(false); > lcdc_write(stat, LCD_MASKED_STAT_REG); > lcd_enable_raster(); > } else if (stat & LCD_PL_LOAD_DONE) { > @@ -734,7 +762,7 @@ static irqreturn_t lcdc_irq_handler_rev02(int irq, > void *arg) > * interrupt via the following write to the status > register. If > * this is done after then one gets multiple PL done > interrupts. > */ > - lcd_disable_raster(); > + lcd_disable_raster(false); > > lcdc_write(stat, LCD_MASKED_STAT_REG); > > @@ -780,7 +808,7 @@ static irqreturn_t lcdc_irq_handler_rev01(int irq, > void *arg) > > if ((stat & LCD_SYNC_LOST) && (stat & LCD_FIFO_UNDERFLOW)) { > pr_err("LCDC sync lost or underflow error occurred\n"); > - lcd_disable_raster(); > + lcd_disable_raster(false); > lcdc_write(stat, LCD_STAT_REG); > lcd_enable_raster(); > } else if (stat & LCD_PL_LOAD_DONE) { > @@ -790,7 +818,7 @@ static irqreturn_t lcdc_irq_handler_rev01(int irq, > void *arg) > * interrupt via the following write to the status > register. If > * this is done after then one gets multiple PL done > interrupts. > */ > - lcd_disable_raster(); > + lcd_disable_raster(false); > > lcdc_write(stat, LCD_STAT_REG); > > @@ -887,7 +915,7 @@ static int lcd_da8xx_cpufreq_transition(struct > notifier_block *nb, > if (val == CPUFREQ_POSTCHANGE) { > if (par->lcd_fck_rate != clk_get_rate(par->lcdc_clk)) { > par->lcd_fck_rate = clk_get_rate(par->lcdc_clk); > - lcd_disable_raster(); > + lcd_disable_raster(true); > lcd_calc_clk_divider(par); > lcd_enable_raster(); > } > @@ -924,7 +952,7 @@ static int __devexit fb_remove(struct platform_device > *dev) > if (par->panel_power_ctrl) > par->panel_power_ctrl(0); > > - lcd_disable_raster(); > + lcd_disable_raster(true); > lcdc_write(0, LCD_RASTER_CTRL_REG); > > /* disable DMA */ > @@ -1037,7 +1065,7 @@ static int cfb_blank(int blank, struct fb_info > *info) > if (par->panel_power_ctrl) > par->panel_power_ctrl(0); > > - lcd_disable_raster(); > + lcd_disable_raster(true); > break; > default: > ret = -EINVAL; > @@ -1377,7 +1405,7 @@ static int fb_suspend(struct platform_device *dev, > pm_message_t state) > par->panel_power_ctrl(0); > > fb_set_suspend(info, 1); > - lcd_disable_raster(); > + lcd_disable_raster(true); > clk_disable(par->lcdc_clk); > console_unlock(); > > -- > 1.7.1 > > _______________________________________________ > Davinci-linux-open-source mailing list > Davinci-linux-open-source@linux.davincidsp.com > http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source -- To unsubscribe from this list: send the line "unsubscribe linux-fbdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Sriram, On Tue, Jul 24, 2012 at 10:11:55, Madhvapathi Sriram wrote: > On Tue, Jul 24, 2012 at 9:39 AM, Manjunathappa, Prakash > <prakash.pm@ti.com> wrote: [...] > > /* Disable the Raster Engine of the LCD Controller */ > > -static inline void lcd_disable_raster(void) > > +static inline void lcd_disable_raster(bool wait_for_frame_done) > > { > > u32 reg; > > + u32 loop_cnt = 0; > > + u32 stat; > > + u32 i = 0; > > + > > + /* 50 milli seconds should be sufficient for a frame to complete > > */ > > + if (wait_for_frame_done) > > + loop_cnt = 50; > > > > reg = lcdc_read(LCD_RASTER_CTRL_REG); > > if (reg & LCD_RASTER_ENABLE) > > lcdc_write(reg & ~LCD_RASTER_ENABLE, LCD_RASTER_CTRL_REG); > > + > > + /* Wait for the current frame to complete */ > > + do { > > + if (lcd_revision == LCD_VERSION_1) > > + stat = lcdc_read(LCD_STAT_REG); > > + else > > + stat = lcdc_read(LCD_RAW_STAT_REG); > > + mdelay(1); > > + } while (!(stat & LCD_FRAME_DONE) && (i++ < loop_cnt)); > > Are you sure it should be do while? You call it from interrupt handler > too (sync lost handling). In that case mdelay() from interrupt > context..not a good idea I feel. > Ok. I will change it as below: while (1) { if (lcd_revision == LCD_VERSION_1) stat = lcdc_read(LCD_STAT_REG); else stat = lcdc_read(LCD_RAW_STAT_REG); if((stat & LCD_FRAME_DONE) || (i++ > loop_cnt)) break; mdelay(1); } > > + > > + if (lcd_revision == LCD_VERSION_1) > > + lcdc_write(stat, LCD_STAT_REG); > > + else > > + lcdc_write(stat, LCD_MASKED_STAT_REG); > > + > > + if ((loop_cnt != 0) && (i >= loop_cnt)) { > > + pr_err("LCD Controller timed out\n"); > > + return; > > return may not be necessary? > Agree, I will remove it. Thanks, Prakash > > + } > > } [...] -- To unsubscribe from this list: send the line "unsubscribe linux-fbdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Tue, Jul 24, 2012 at 12:47:02, Manjunathappa, Prakash wrote: > Hi Sriram, > > On Tue, Jul 24, 2012 at 10:11:55, Madhvapathi Sriram wrote: > > On Tue, Jul 24, 2012 at 9:39 AM, Manjunathappa, Prakash > > <prakash.pm@ti.com> wrote: > [...] > > > /* Disable the Raster Engine of the LCD Controller */ > > > -static inline void lcd_disable_raster(void) > > > +static inline void lcd_disable_raster(bool wait_for_frame_done) > > > { > > > u32 reg; > > > + u32 loop_cnt = 0; > > > + u32 stat; > > > + u32 i = 0; > > > + > > > + /* 50 milli seconds should be sufficient for a frame to complete > > > */ > > > + if (wait_for_frame_done) > > > + loop_cnt = 50; > > > > > > reg = lcdc_read(LCD_RASTER_CTRL_REG); > > > if (reg & LCD_RASTER_ENABLE) > > > lcdc_write(reg & ~LCD_RASTER_ENABLE, LCD_RASTER_CTRL_REG); > > > + > > > + /* Wait for the current frame to complete */ > > > + do { > > > + if (lcd_revision == LCD_VERSION_1) > > > + stat = lcdc_read(LCD_STAT_REG); > > > + else > > > + stat = lcdc_read(LCD_RAW_STAT_REG); > > > + mdelay(1); > > > + } while (!(stat & LCD_FRAME_DONE) && (i++ < loop_cnt)); > > > > Are you sure it should be do while? You call it from interrupt handler > > too (sync lost handling). In that case mdelay() from interrupt > > context..not a good idea I feel. > > > > Ok. I will change it as below: > > while (1) { > if (lcd_revision == LCD_VERSION_1) > stat = lcdc_read(LCD_STAT_REG); > else > stat = lcdc_read(LCD_RAW_STAT_REG); > if((stat & LCD_FRAME_DONE) || (i++ > loop_cnt)) s/i++/++i Thanks, Prakash > break; > mdelay(1); > } > > > > + > > > + if (lcd_revision == LCD_VERSION_1) > > > + lcdc_write(stat, LCD_STAT_REG); > > > + else > > > + lcdc_write(stat, LCD_MASKED_STAT_REG); > > > + > > > + if ((loop_cnt != 0) && (i >= loop_cnt)) { > > > + pr_err("LCD Controller timed out\n"); > > > + return; > > > > return may not be necessary? > > > > Agree, I will remove it. > > Thanks, > Prakash > > > > + } > > > } > > [...] > > -- To unsubscribe from this list: send the line "unsubscribe linux-fbdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Tue, Jul 24, 2012 at 12:47 PM, Manjunathappa, Prakash <prakash.pm@ti.com> wrote: > Hi Sriram, > > On Tue, Jul 24, 2012 at 10:11:55, Madhvapathi Sriram wrote: >> On Tue, Jul 24, 2012 at 9:39 AM, Manjunathappa, Prakash >> <prakash.pm@ti.com> wrote: > [...] >> > /* Disable the Raster Engine of the LCD Controller */ >> > -static inline void lcd_disable_raster(void) >> > +static inline void lcd_disable_raster(bool wait_for_frame_done) >> > { >> > u32 reg; >> > + u32 loop_cnt = 0; >> > + u32 stat; >> > + u32 i = 0; >> > + >> > + /* 50 milli seconds should be sufficient for a frame to complete >> > */ >> > + if (wait_for_frame_done) >> > + loop_cnt = 50; >> > >> > reg = lcdc_read(LCD_RASTER_CTRL_REG); >> > if (reg & LCD_RASTER_ENABLE) >> > lcdc_write(reg & ~LCD_RASTER_ENABLE, LCD_RASTER_CTRL_REG); >> > + >> > + /* Wait for the current frame to complete */ >> > + do { >> > + if (lcd_revision == LCD_VERSION_1) >> > + stat = lcdc_read(LCD_STAT_REG); >> > + else >> > + stat = lcdc_read(LCD_RAW_STAT_REG); >> > + mdelay(1); >> > + } while (!(stat & LCD_FRAME_DONE) && (i++ < loop_cnt)); >> >> Are you sure it should be do while? You call it from interrupt handler >> too (sync lost handling). In that case mdelay() from interrupt >> context..not a good idea I feel. >> > > Ok. I will change it as below: > > while (1) { > if (lcd_revision == LCD_VERSION_1) > stat = lcdc_read(LCD_STAT_REG); > else > stat = lcdc_read(LCD_RAW_STAT_REG); > if((stat & LCD_FRAME_DONE) || (i++ > loop_cnt)) > break; > mdelay(1); > } > Hmm.. while(1) could be avoided though. Club all frame-done-wait related at one place. I leave it open for your choice. Some where in the beginning of fxn.... u32 stat_reg = LCD_STAT_REG; Avoids conditions in loop.... if (lcd_revision == LCD_VERSION_2) stat_reg = LCD_RAW_STAT_REG; if (wait_for_frame_done) { u32 loop_count = 50; while (!(lcdc_read(stat_reg) & LCD_FRAME_DONE)) { /* Handle timeout */ if(unlikely(0 == --loop_count)) { pr_err("LCD Controller timed out\n"); break; } mdelay(1); } } >> > + >> > + if (lcd_revision == LCD_VERSION_1) >> > + lcdc_write(stat, LCD_STAT_REG); >> > + else >> > + lcdc_write(stat, LCD_MASKED_STAT_REG); >> > + >> > + if ((loop_cnt != 0) && (i >= loop_cnt)) { >> > + pr_err("LCD Controller timed out\n"); >> > + return; >> >> return may not be necessary? >> > > Agree, I will remove it. > > Thanks, > Prakash > >> > + } >> > } > > [...] > -- To unsubscribe from this list: send the line "unsubscribe linux-fbdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Tue, Jul 24, 2012 at 14:08:05, Madhvapathi Sriram wrote: > On Tue, Jul 24, 2012 at 12:47 PM, Manjunathappa, Prakash > <prakash.pm@ti.com> wrote: > > Hi Sriram, > > > > On Tue, Jul 24, 2012 at 10:11:55, Madhvapathi Sriram wrote: > >> On Tue, Jul 24, 2012 at 9:39 AM, Manjunathappa, Prakash > >> <prakash.pm@ti.com> wrote: > > [...] > >> > /* Disable the Raster Engine of the LCD Controller */ > >> > -static inline void lcd_disable_raster(void) > >> > +static inline void lcd_disable_raster(bool wait_for_frame_done) > >> > { > >> > u32 reg; > >> > + u32 loop_cnt = 0; > >> > + u32 stat; > >> > + u32 i = 0; > >> > + > >> > + /* 50 milli seconds should be sufficient for a frame to complete > >> > */ > >> > + if (wait_for_frame_done) > >> > + loop_cnt = 50; > >> > > >> > reg = lcdc_read(LCD_RASTER_CTRL_REG); > >> > if (reg & LCD_RASTER_ENABLE) > >> > lcdc_write(reg & ~LCD_RASTER_ENABLE, LCD_RASTER_CTRL_REG); > >> > + > >> > + /* Wait for the current frame to complete */ > >> > + do { > >> > + if (lcd_revision == LCD_VERSION_1) > >> > + stat = lcdc_read(LCD_STAT_REG); > >> > + else > >> > + stat = lcdc_read(LCD_RAW_STAT_REG); > >> > + mdelay(1); > >> > + } while (!(stat & LCD_FRAME_DONE) && (i++ < loop_cnt)); > >> > >> Are you sure it should be do while? You call it from interrupt handler > >> too (sync lost handling). In that case mdelay() from interrupt > >> context..not a good idea I feel. > >> > > > > Ok. I will change it as below: > > > > while (1) { > > if (lcd_revision == LCD_VERSION_1) > > stat = lcdc_read(LCD_STAT_REG); > > else > > stat = lcdc_read(LCD_RAW_STAT_REG); > > if((stat & LCD_FRAME_DONE) || (i++ > loop_cnt)) > > break; > > mdelay(1); > > } > > > Hmm.. while(1) could be avoided though. Club all frame-done-wait > related at one place. I leave it open for your choice. > > Some where in the beginning of fxn.... > u32 stat_reg = LCD_STAT_REG; > > Avoids conditions in loop.... > if (lcd_revision == LCD_VERSION_2) > stat_reg = LCD_RAW_STAT_REG; > > if (wait_for_frame_done) { > u32 loop_count = 50; > > while (!(lcdc_read(stat_reg) & LCD_FRAME_DONE)) { > /* Handle timeout */ > if(unlikely(0 == --loop_count)) { > pr_err("LCD Controller timed out\n"); > break; > } > mdelay(1); > } > } > > Thanks Sriram, I will consider this. > >> > + > >> > + if (lcd_revision == LCD_VERSION_1) > >> > + lcdc_write(stat, LCD_STAT_REG); > >> > + else > >> > + lcdc_write(stat, LCD_MASKED_STAT_REG); > >> > + > >> > + if ((loop_cnt != 0) && (i >= loop_cnt)) { > >> > + pr_err("LCD Controller timed out\n"); > >> > + return; > >> > >> return may not be necessary? > >> > > > > Agree, I will remove it. > > > > Thanks, > > Prakash > > > >> > + } > >> > } > > > > [...] > > > -- To unsubscribe from this list: send the line "unsubscribe linux-fbdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/video/da8xx-fb.c b/drivers/video/da8xx-fb.c index a908dfd..0fb4d7d 100644 --- a/drivers/video/da8xx-fb.c +++ b/drivers/video/da8xx-fb.c @@ -31,6 +31,7 @@ #include <linux/cpufreq.h> #include <linux/console.h> #include <linux/slab.h> +#include <linux/delay.h> #include <video/da8xx-fb.h> #include <asm/div64.h> @@ -45,6 +46,7 @@ #define LCD_PL_LOAD_DONE BIT(6) #define LCD_FIFO_UNDERFLOW BIT(5) #define LCD_SYNC_LOST BIT(2) +#define LCD_FRAME_DONE BIT(0) /* LCD DMA Control Register */ #define LCD_DMA_BURST_SIZE(x) ((x) << 4) @@ -279,13 +281,39 @@ static inline void lcd_enable_raster(void) } /* Disable the Raster Engine of the LCD Controller */ -static inline void lcd_disable_raster(void) +static inline void lcd_disable_raster(bool wait_for_frame_done) { u32 reg; + u32 loop_cnt = 0; + u32 stat; + u32 i = 0; + + /* 50 milli seconds should be sufficient for a frame to complete */ + if (wait_for_frame_done) + loop_cnt = 50; reg = lcdc_read(LCD_RASTER_CTRL_REG); if (reg & LCD_RASTER_ENABLE) lcdc_write(reg & ~LCD_RASTER_ENABLE, LCD_RASTER_CTRL_REG); + + /* Wait for the current frame to complete */ + do { + if (lcd_revision == LCD_VERSION_1) + stat = lcdc_read(LCD_STAT_REG); + else + stat = lcdc_read(LCD_RAW_STAT_REG); + mdelay(1); + } while (!(stat & LCD_FRAME_DONE) && (i++ < loop_cnt)); + + if (lcd_revision == LCD_VERSION_1) + lcdc_write(stat, LCD_STAT_REG); + else + lcdc_write(stat, LCD_MASKED_STAT_REG); + + if ((loop_cnt != 0) && (i >= loop_cnt)) { + pr_err("LCD Controller timed out\n"); + return; + } } static void lcd_blit(int load_mode, struct da8xx_fb_par *par) @@ -626,7 +654,7 @@ static int fb_setcolreg(unsigned regno, unsigned red, unsigned green, static void lcd_reset(struct da8xx_fb_par *par) { /* Disable the Raster if previously Enabled */ - lcd_disable_raster(); + lcd_disable_raster(false); /* DMA has to be disabled */ lcdc_write(0, LCD_DMA_CTRL_REG); @@ -724,7 +752,7 @@ static irqreturn_t lcdc_irq_handler_rev02(int irq, void *arg) if ((stat & LCD_SYNC_LOST) && (stat & LCD_FIFO_UNDERFLOW)) { pr_err("LCDC sync lost or underflow error occurred\n"); - lcd_disable_raster(); + lcd_disable_raster(false); lcdc_write(stat, LCD_MASKED_STAT_REG); lcd_enable_raster(); } else if (stat & LCD_PL_LOAD_DONE) { @@ -734,7 +762,7 @@ static irqreturn_t lcdc_irq_handler_rev02(int irq, void *arg) * interrupt via the following write to the status register. If * this is done after then one gets multiple PL done interrupts. */ - lcd_disable_raster(); + lcd_disable_raster(false); lcdc_write(stat, LCD_MASKED_STAT_REG); @@ -780,7 +808,7 @@ static irqreturn_t lcdc_irq_handler_rev01(int irq, void *arg) if ((stat & LCD_SYNC_LOST) && (stat & LCD_FIFO_UNDERFLOW)) { pr_err("LCDC sync lost or underflow error occurred\n"); - lcd_disable_raster(); + lcd_disable_raster(false); lcdc_write(stat, LCD_STAT_REG); lcd_enable_raster(); } else if (stat & LCD_PL_LOAD_DONE) { @@ -790,7 +818,7 @@ static irqreturn_t lcdc_irq_handler_rev01(int irq, void *arg) * interrupt via the following write to the status register. If * this is done after then one gets multiple PL done interrupts. */ - lcd_disable_raster(); + lcd_disable_raster(false); lcdc_write(stat, LCD_STAT_REG); @@ -887,7 +915,7 @@ static int lcd_da8xx_cpufreq_transition(struct notifier_block *nb, if (val == CPUFREQ_POSTCHANGE) { if (par->lcd_fck_rate != clk_get_rate(par->lcdc_clk)) { par->lcd_fck_rate = clk_get_rate(par->lcdc_clk); - lcd_disable_raster(); + lcd_disable_raster(true); lcd_calc_clk_divider(par); lcd_enable_raster(); } @@ -924,7 +952,7 @@ static int __devexit fb_remove(struct platform_device *dev) if (par->panel_power_ctrl) par->panel_power_ctrl(0); - lcd_disable_raster(); + lcd_disable_raster(true); lcdc_write(0, LCD_RASTER_CTRL_REG); /* disable DMA */ @@ -1037,7 +1065,7 @@ static int cfb_blank(int blank, struct fb_info *info) if (par->panel_power_ctrl) par->panel_power_ctrl(0); - lcd_disable_raster(); + lcd_disable_raster(true); break; default: ret = -EINVAL; @@ -1377,7 +1405,7 @@ static int fb_suspend(struct platform_device *dev, pm_message_t state) par->panel_power_ctrl(0); fb_set_suspend(info, 1); - lcd_disable_raster(); + lcd_disable_raster(true); clk_disable(par->lcdc_clk); console_unlock();
Wait for active frame transfer to complete after disabling LCDC. At the same this wait is not be required when there are sync and underflow errors. More information on disable and reset sequence can be found in section 13.4.6 of AM335x TRM @www.ti.com/am335x. Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com> --- Patch applies on top of below patch under review: http://marc.info/?l=linux-fbdev&m=134280060828708&w=2 "video: da8xx-fb: do clock reset of revision 2 LCDC before enabling" Since v1: Changed the commit message, also added link to hardware specification. drivers/video/da8xx-fb.c | 48 ++++++++++++++++++++++++++++++++++++--------- 1 files changed, 38 insertions(+), 10 deletions(-)