| Message ID | 1345582058-2291-8-git-send-email-linux@prisktech.co.nz (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
On 08/21/2012 02:47 PM, Tony Prisk wrote: > Bindings for gpio, interrupt controller, power management controller, > timer, realtime clock, serial uart, ehci and uhci controllers and > framebuffer controllers used on the arch-vt8500 platform. > > Framebuffer binding also specifies a 'display' node which is required > for determining the lcd panel data. > diff --git a/Documentation/devicetree/bindings/gpio/gpio_vt8500.txt b/Documentation/devicetree/bindings/gpio/gpio_vt8500.txt > +- #gpio-cells : should be <3>. > + 1) bank > + 2) pin number > + 3) flags Should this enumerate what legal values are for flags, or point at a standard document that does? > diff --git a/Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt b/Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt > + uart@d8210000 { > + compatible = "via,vt8500-uart"; > + reg = <0xd8210000 0x1040>; > + interrupts = <47>; > + }; How does the UART know what frequency its clock input is, in order to calculate dividers? Should there be a clocks property to link to the input clock, so the rate can be queried? If so, a reference to the common clock binding, plus a specification of which clocks must be listed in the clock property should be included here. > diff --git a/Documentation/devicetree/bindings/video/via,vt8500-fb.txt b/Documentation/devicetree/bindings/video/via,vt8500-fb.txt > +VIA VT8500 Display > +----------------------------------------------------- > +Required properties: > +- xres : lcd panel horizontal resolution > +- yres : lcd panel vertical resolution > +- left-margin, > +- right-margin, > +- hsync-len: lcd panel horizontal timings in pixels > +- upper-margin, > +- lower-margin, > +- vsync-len: lcd panel verticals timings in pixels > +- bpp: lcd panel bit-depth. > + <16> for RGB565, <32> for RGB888 Shouldn't this reference Sascha Hauer's binding document (although I suppose it isn't checked in yet), and just document the additions? I wonder if this binding should be written assuming Sascha's binding doc will be checked in? -- To unsubscribe from this list: send the line "unsubscribe linux-fbdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Wed, 2012-08-22 at 15:07 -0600, Stephen Warren wrote: > On 08/21/2012 02:47 PM, Tony Prisk wrote: > > Bindings for gpio, interrupt controller, power management controller, > > timer, realtime clock, serial uart, ehci and uhci controllers and > > framebuffer controllers used on the arch-vt8500 platform. > > > > Framebuffer binding also specifies a 'display' node which is required > > for determining the lcd panel data. > > > diff --git a/Documentation/devicetree/bindings/gpio/gpio_vt8500.txt b/Documentation/devicetree/bindings/gpio/gpio_vt8500.txt > > > +- #gpio-cells : should be <3>. > > + 1) bank > > + 2) pin number > > + 3) flags > > Should this enumerate what legal values are for flags, or point at a > standard document that does? There currently are no supported flags - guess this was an oversight. I'll take a look if there are any that we might require in the future and implement them otherwise I'll drop the flags reference. > > > diff --git a/Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt b/Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt > > > + uart@d8210000 { > > + compatible = "via,vt8500-uart"; > > + reg = <0xd8210000 0x1040>; > > + interrupts = <47>; > > + }; > > How does the UART know what frequency its clock input is, in order to > calculate dividers? Should there be a clocks property to link to the > input clock, so the rate can be queried? If so, a reference to the > common clock binding, plus a specification of which clocks must be > listed in the clock property should be included here. > I didn't revisit the code that had already been posted in v1/v2 when I added the common clock code and there was no clock handling code at that point. The uart's are all clocked via a clkgen that outputs 24Mhz and this was hardcoded in the driver. I will correct this and add the appropriate device tree entries and documentation. > > diff --git a/Documentation/devicetree/bindings/video/via,vt8500-fb.txt b/Documentation/devicetree/bindings/video/via,vt8500-fb.txt > > > +VIA VT8500 Display > > +----------------------------------------------------- > > +Required properties: > > +- xres : lcd panel horizontal resolution > > +- yres : lcd panel vertical resolution > > +- left-margin, > > +- right-margin, > > +- hsync-len: lcd panel horizontal timings in pixels > > +- upper-margin, > > +- lower-margin, > > +- vsync-len: lcd panel verticals timings in pixels > > +- bpp: lcd panel bit-depth. > > + <16> for RGB565, <32> for RGB888 > > Shouldn't this reference Sascha Hauer's binding document (although I > suppose it isn't checked in yet), and just document the additions? I > wonder if this binding should be written assuming Sascha's binding doc > will be checked in? I haven't seen Sascha's binding yet - I'm not even sure its been agreed upon but it does seem to be the most likely candidate so far. Hopefully it will get accepted in this window, and I will have time to do exactly as you commented, which was the plan from the start. This binding was based on the most current one I had seen suggested at the time. Given the additional comments for this patch set, and the required changes I'll hold off posting v4 until everything is tidied up. Regards Tony Prisk -- To unsubscribe from this list: send the line "unsubscribe linux-fbdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/arm/vt8500.txt b/Documentation/devicetree/bindings/arm/vt8500.txt new file mode 100644 index 0000000..1b3b187 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vt8500.txt @@ -0,0 +1,15 @@ +VIA/Wondermedia VT8500 Platforms Device Tree Bindings +--------------------------------------- + +Boards with the VIA VT8500 SoC shall have the following properties: +Required root node property: +compatible = "via,vt8500"; + +Boards with the Wondermedia WM8505 SoC shall have the following properties: +Required root node property: +compatible = "wm,wm8505"; + +Boards with the Wondermedia WM8650 SoC shall have the following properties: +Required root node property: +compatible = "wm,wm8650"; + diff --git a/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-intc.txt b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-intc.txt new file mode 100644 index 0000000..0a4ce10 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-intc.txt @@ -0,0 +1,16 @@ +VIA/Wondermedia VT8500 Interrupt Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-intc" +- reg : Should contain 1 register ranges(address and length) +- #interrupt-cells : should be <1> + +Example: + + intc: interrupt-controller@d8140000 { + compatible = "via,vt8500-intc"; + interrupt-controller; + reg = <0xd8140000 0x10000>; + #interrupt-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-pmc.txt b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-pmc.txt new file mode 100644 index 0000000..521b9c7 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-pmc.txt @@ -0,0 +1,13 @@ +VIA/Wondermedia VT8500 Power Management Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-pmc" +- reg : Should contain 1 register ranges(address and length) + +Example: + + pmc@d8130000 { + compatible = "via,vt8500-pmc"; + reg = <0xd8130000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-timer.txt b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-timer.txt new file mode 100644 index 0000000..901c73f --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-timer.txt @@ -0,0 +1,15 @@ +VIA/Wondermedia VT8500 Timer +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-timer" +- reg : Should contain 1 register ranges(address and length) +- interrupts : interrupt for the timer + +Example: + + timer@d8130100 { + compatible = "via,vt8500-timer"; + reg = <0xd8130100 0x28>; + interrupts = <36>; + }; diff --git a/Documentation/devicetree/bindings/clock/vt8500.txt b/Documentation/devicetree/bindings/clock/vt8500.txt new file mode 100644 index 0000000..a880c70 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/vt8500.txt @@ -0,0 +1,72 @@ +Device Tree Clock bindings for arch-vt8500 + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of the following: + "via,vt8500-pll-clock" - for a VT8500/WM8505 PLL clock + "wm,wm8650-pll-clock" - for a WM8650 PLL clock + "via,vt8500-device-clock" - for a VT/WM device clock + +Required properties for PLL clocks: +- reg : shall be the control register offset from PMC base for the pll clock. +- clocks : shall be the input parent clock phandle for the clock. This should + be the reference clock. +- #clock-cells : from common clock binding; shall be set to 0. + +Required properties for device clocks: +- clocks : shall be the input parent clock phandle for the clock. This should + be a pll output. +- #clock-cells : from common clock binding; shall be set to 0. + + +Device Clocks + +Device clocks are required to have one or both of the following sets of +properties: + + +Gated device clocks: + +Required properties: +- enable-reg : shall be the register offset from PMC base for the enable + register. +- enable-bit : shall be the bit within enable-reg to enable/disable the clock. + + +Divisor device clocks: + +Required property: +- divisor-reg : shall be the register offset from PMC base for the divisor + register. +Optional property: +- divisor-mask : shall be the mask for the divisor register. Defaults to 0x1f + if not specified. + + +For example: + +ref25: ref25M { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; +}; + +plla: plla { + #clock-cells = <0>; + compatible = "wm,wm8650-pll-clock"; + clocks = <&ref25>; + reg = <0x200>; +}; + +sdhc: sdhc { + #clock-cells = <0>; + compatible = "via,vt8500-device-clock"; + clocks = <&pllb>; + divisor-reg = <0x328>; + divisor-mask = <0x3f>; + enable-reg = <0x254>; + enable-bit = <18>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio_vt8500.txt b/Documentation/devicetree/bindings/gpio/gpio_vt8500.txt new file mode 100644 index 0000000..1a122bf --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio_vt8500.txt @@ -0,0 +1,24 @@ +VIA/Wondermedia VT8500 GPIO Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-gpio", "wm,wm8505-gpio" + or "wm,wm8650-gpio" depending on your SoC +- reg : Should contain 1 register range (address and length) +- #gpio-cells : should be <3>. + 1) bank + 2) pin number + 3) flags + +Example: + + gpio: gpio-controller@d8110000 { + compatible = "via,vt8500-gpio"; + gpio-controller; + reg = <0xd8110000 0x10000>; + #gpio-cells = <3>; + }; + + vibrate { + gpios = <&gpio 0 1 0>; /* Bank 0, Pin 1, No flags */ + }; diff --git a/Documentation/devicetree/bindings/rtc/via,vt8500-rtc.txt b/Documentation/devicetree/bindings/rtc/via,vt8500-rtc.txt new file mode 100644 index 0000000..3c0484c --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/via,vt8500-rtc.txt @@ -0,0 +1,15 @@ +VIA/Wondermedia VT8500 Realtime Clock Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-rtc" +- reg : Should contain 1 register ranges(address and length) +- interrupts : alarm interrupt + +Example: + + rtc@d8100000 { + compatible = "via,vt8500-rtc"; + reg = <0xd8100000 0x10000>; + interrupts = <48>; + }; diff --git a/Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt b/Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt new file mode 100644 index 0000000..3222502 --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt @@ -0,0 +1,15 @@ +VIA/Wondermedia VT8500 UART Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-uart" +- reg : Should contain 1 register ranges(address and length) +- interrupts : UART interrupt + +Example: + + uart@d8210000 { + compatible = "via,vt8500-uart"; + reg = <0xd8210000 0x1040>; + interrupts = <47>; + }; diff --git a/Documentation/devicetree/bindings/usb/platform-uhci.txt b/Documentation/devicetree/bindings/usb/platform-uhci.txt new file mode 100644 index 0000000..a4fb071 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/platform-uhci.txt @@ -0,0 +1,15 @@ +Generic Platform UHCI Controller +----------------------------------------------------- + +Required properties: +- compatible : "platform-uhci" +- reg : Should contain 1 register ranges(address and length) +- interrupts : UHCI controller interrupt + +Example: + + uhci@d8007b00 { + compatible = "platform-uhci"; + reg = <0xd8007b00 0x200>; + interrupts = <43>; + }; diff --git a/Documentation/devicetree/bindings/usb/via,vt8500-ehci.txt b/Documentation/devicetree/bindings/usb/via,vt8500-ehci.txt new file mode 100644 index 0000000..17b3ad1 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/via,vt8500-ehci.txt @@ -0,0 +1,15 @@ +VIA/Wondermedia VT8500 EHCI Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-ehci" +- reg : Should contain 1 register ranges(address and length) +- interrupts : ehci controller interrupt + +Example: + + ehci@d8007900 { + compatible = "via,vt8500-ehci"; + reg = <0xd8007900 0x200>; + interrupts = <43>; + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index db4d3af..5c63da2 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -47,5 +47,7 @@ sirf SiRF Technology, Inc. st STMicroelectronics stericsson ST-Ericsson ti Texas Instruments +via VIA Technologies, Inc. wlf Wolfson Microelectronics +wm Wondermedia Technologies, Inc. xlnx Xilinx diff --git a/Documentation/devicetree/bindings/video/via,vt8500-fb.txt b/Documentation/devicetree/bindings/video/via,vt8500-fb.txt new file mode 100644 index 0000000..98ad14c --- /dev/null +++ b/Documentation/devicetree/bindings/video/via,vt8500-fb.txt @@ -0,0 +1,48 @@ +VIA VT8500 Framebuffer +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-fb" +- reg : Should contain 1 register ranges(address and length) +- interrupts : framebuffer controller interrupt +- via,display: a phandle pointing to the display node + +Required nodes: +- display: a display node is required to initialize the lcd panel + This should be in the board dts. + +Example: + + fb@d800e400 { + compatible = "via,vt8500-fb"; + reg = <0xd800e400 0x400>; + interrupts = <12>; + via,display = <&display>; + }; + +VIA VT8500 Display +----------------------------------------------------- +Required properties: +- xres : lcd panel horizontal resolution +- yres : lcd panel vertical resolution +- left-margin, +- right-margin, +- hsync-len: lcd panel horizontal timings in pixels +- upper-margin, +- lower-margin, +- vsync-len: lcd panel verticals timings in pixels +- bpp: lcd panel bit-depth. + <16> for RGB565, <32> for RGB888 + +Example: + display { + xres = <800>; + yres = <480>; + left-margin = <88>; + right-margin = <40>; + hsync-len = <0>; + upper-margin = <32>; + lower-margin = <11>; + vsync-len = <1>; + bpp = <16>; + }; diff --git a/Documentation/devicetree/bindings/video/wm,prizm-ge-rops.txt b/Documentation/devicetree/bindings/video/wm,prizm-ge-rops.txt new file mode 100644 index 0000000..a850fa0 --- /dev/null +++ b/Documentation/devicetree/bindings/video/wm,prizm-ge-rops.txt @@ -0,0 +1,13 @@ +VIA/Wondermedia Graphics Engine Controller +----------------------------------------------------- + +Required properties: +- compatible : "wm,prizm-ge-rops" +- reg : Should contain 1 register ranges(address and length) + +Example: + + ge_rops@d8050400 { + compatible = "wm,prizm-ge-rops"; + reg = <0xd8050400 0x100>; + }; diff --git a/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt b/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt new file mode 100644 index 0000000..64f016a --- /dev/null +++ b/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt @@ -0,0 +1,22 @@ +Wondermedia WM8505 Framebuffer +----------------------------------------------------- + +Required properties: +- compatible : "wm,wm8505-fb" +- reg : Should contain 1 register ranges(address and length) +- via,display: a phandle pointing to the display node + +Required nodes: +- display: a display node is required to initialize the lcd panel + This should be in the board dts. See definition in + Documentation/devicetree/bindings/video/via,vt8500-fb.txt + + +Example: + + fb@d8050800 { + compatible = "wm,wm8505-fb"; + reg = <0xd8050800 0x200>; + via,display = <&display>; + }; +
Bindings for gpio, interrupt controller, power management controller, timer, realtime clock, serial uart, ehci and uhci controllers and framebuffer controllers used on the arch-vt8500 platform. Framebuffer binding also specifies a 'display' node which is required for determining the lcd panel data. Signed-off-by: Tony Prisk <linux@prisktech.co.nz> --- Documentation/devicetree/bindings/arm/vt8500.txt | 15 ++++ .../bindings/arm/vt8500/via,vt8500-intc.txt | 16 +++++ .../bindings/arm/vt8500/via,vt8500-pmc.txt | 13 ++++ .../bindings/arm/vt8500/via,vt8500-timer.txt | 15 ++++ Documentation/devicetree/bindings/clock/vt8500.txt | 72 ++++++++++++++++++++ .../devicetree/bindings/gpio/gpio_vt8500.txt | 24 +++++++ .../devicetree/bindings/rtc/via,vt8500-rtc.txt | 15 ++++ .../bindings/tty/serial/via,vt8500-uart.txt | 15 ++++ .../devicetree/bindings/usb/platform-uhci.txt | 15 ++++ .../devicetree/bindings/usb/via,vt8500-ehci.txt | 15 ++++ .../devicetree/bindings/vendor-prefixes.txt | 2 + .../devicetree/bindings/video/via,vt8500-fb.txt | 48 +++++++++++++ .../devicetree/bindings/video/wm,prizm-ge-rops.txt | 13 ++++ .../devicetree/bindings/video/wm,wm8505-fb.txt | 22 ++++++ 14 files changed, 300 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/vt8500.txt create mode 100644 Documentation/devicetree/bindings/arm/vt8500/via,vt8500-intc.txt create mode 100644 Documentation/devicetree/bindings/arm/vt8500/via,vt8500-pmc.txt create mode 100644 Documentation/devicetree/bindings/arm/vt8500/via,vt8500-timer.txt create mode 100644 Documentation/devicetree/bindings/clock/vt8500.txt create mode 100644 Documentation/devicetree/bindings/gpio/gpio_vt8500.txt create mode 100644 Documentation/devicetree/bindings/rtc/via,vt8500-rtc.txt create mode 100644 Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt create mode 100644 Documentation/devicetree/bindings/usb/platform-uhci.txt create mode 100644 Documentation/devicetree/bindings/usb/via,vt8500-ehci.txt create mode 100644 Documentation/devicetree/bindings/video/via,vt8500-fb.txt create mode 100644 Documentation/devicetree/bindings/video/wm,prizm-ge-rops.txt create mode 100644 Documentation/devicetree/bindings/video/wm,wm8505-fb.txt