@@ -28,6 +28,7 @@
#include <linux/omapfb.h>
#include <linux/io.h>
#include <linux/platform_data/gpio-omap.h>
+#include <linux/soc/ti/omap1-mux.h>
#include <asm/serial.h>
#include <asm/mach-types.h>
@@ -37,19 +37,10 @@
#define __ASM_ARCH_OMAP_HARDWARE_H
#include <linux/sizes.h>
+#include <linux/soc/ti/omap1-io.h>
#ifndef __ASSEMBLER__
#include <asm/types.h>
-#include <mach/soc.h>
-
-/*
- * NOTE: Please use ioremap + __raw_read/write where possible instead of these
- */
-extern u8 omap_readb(u32 pa);
-extern u16 omap_readw(u32 pa);
-extern u32 omap_readl(u32 pa);
-extern void omap_writeb(u8 v, u32 pa);
-extern void omap_writew(u16 v, u32 pa);
-extern void omap_writel(u32 v, u32 pa);
+#include <linux/soc/ti/omap1-soc.h>
#include <mach/tc.h>
@@ -98,66 +89,6 @@ static inline u32 omap_cs3_phys(void)
#define MPU_TIMER_AR (1 << 1)
#define MPU_TIMER_ST (1 << 0)
-/*
- * ----------------------------------------------------------------------------
- * Clocks
- * ----------------------------------------------------------------------------
- */
-#define CLKGEN_REG_BASE (0xfffece00)
-#define ARM_CKCTL (CLKGEN_REG_BASE + 0x0)
-#define ARM_IDLECT1 (CLKGEN_REG_BASE + 0x4)
-#define ARM_IDLECT2 (CLKGEN_REG_BASE + 0x8)
-#define ARM_EWUPCT (CLKGEN_REG_BASE + 0xC)
-#define ARM_RSTCT1 (CLKGEN_REG_BASE + 0x10)
-#define ARM_RSTCT2 (CLKGEN_REG_BASE + 0x14)
-#define ARM_SYSST (CLKGEN_REG_BASE + 0x18)
-#define ARM_IDLECT3 (CLKGEN_REG_BASE + 0x24)
-
-#define CK_RATEF 1
-#define CK_IDLEF 2
-#define CK_ENABLEF 4
-#define CK_SELECTF 8
-#define SETARM_IDLE_SHIFT
-
-/* DPLL control registers */
-#define DPLL_CTL (0xfffecf00)
-
-/* DSP clock control. Must use __raw_readw() and __raw_writew() with these */
-#define DSP_CONFIG_REG_BASE IOMEM(0xe1008000)
-#define DSP_CKCTL (DSP_CONFIG_REG_BASE + 0x0)
-#define DSP_IDLECT1 (DSP_CONFIG_REG_BASE + 0x4)
-#define DSP_IDLECT2 (DSP_CONFIG_REG_BASE + 0x8)
-#define DSP_RSTCT2 (DSP_CONFIG_REG_BASE + 0x14)
-
-/*
- * ---------------------------------------------------------------------------
- * UPLD
- * ---------------------------------------------------------------------------
- */
-#define ULPD_REG_BASE (0xfffe0800)
-#define ULPD_IT_STATUS (ULPD_REG_BASE + 0x14)
-#define ULPD_SETUP_ANALOG_CELL_3 (ULPD_REG_BASE + 0x24)
-#define ULPD_CLOCK_CTRL (ULPD_REG_BASE + 0x30)
-# define DIS_USB_PVCI_CLK (1 << 5) /* no USB/FAC synch */
-# define USB_MCLK_EN (1 << 4) /* enable W4_USB_CLKO */
-#define ULPD_SOFT_REQ (ULPD_REG_BASE + 0x34)
-# define SOFT_UDC_REQ (1 << 4)
-# define SOFT_USB_CLK_REQ (1 << 3)
-# define SOFT_DPLL_REQ (1 << 0)
-#define ULPD_DPLL_CTRL (ULPD_REG_BASE + 0x3c)
-#define ULPD_STATUS_REQ (ULPD_REG_BASE + 0x40)
-#define ULPD_APLL_CTRL (ULPD_REG_BASE + 0x4c)
-#define ULPD_POWER_CTRL (ULPD_REG_BASE + 0x50)
-#define ULPD_SOFT_DISABLE_REQ_REG (ULPD_REG_BASE + 0x68)
-# define DIS_MMC2_DPLL_REQ (1 << 11)
-# define DIS_MMC1_DPLL_REQ (1 << 10)
-# define DIS_UART3_DPLL_REQ (1 << 9)
-# define DIS_UART2_DPLL_REQ (1 << 8)
-# define DIS_UART1_DPLL_REQ (1 << 7)
-# define DIS_USB_HOST_DPLL_REQ (1 << 6)
-#define ULPD_SDW_CLK_DIV_CTRL_SEL (ULPD_REG_BASE + 0x74)
-#define ULPD_CAM_CLK_CTRL (ULPD_REG_BASE + 0x7c)
-
/*
* ---------------------------------------------------------------------------
* Watchdog timer
@@ -213,52 +144,6 @@ static inline u32 omap_cs3_phys(void)
#endif
-/*
- * ----------------------------------------------------------------------------
- * System control registers
- * ----------------------------------------------------------------------------
- */
-#define MOD_CONF_CTRL_0 0xfffe1080
-#define MOD_CONF_CTRL_1 0xfffe1110
-
-/*
- * ----------------------------------------------------------------------------
- * Pin multiplexing registers
- * ----------------------------------------------------------------------------
- */
-#define FUNC_MUX_CTRL_0 0xfffe1000
-#define FUNC_MUX_CTRL_1 0xfffe1004
-#define FUNC_MUX_CTRL_2 0xfffe1008
-#define COMP_MODE_CTRL_0 0xfffe100c
-#define FUNC_MUX_CTRL_3 0xfffe1010
-#define FUNC_MUX_CTRL_4 0xfffe1014
-#define FUNC_MUX_CTRL_5 0xfffe1018
-#define FUNC_MUX_CTRL_6 0xfffe101C
-#define FUNC_MUX_CTRL_7 0xfffe1020
-#define FUNC_MUX_CTRL_8 0xfffe1024
-#define FUNC_MUX_CTRL_9 0xfffe1028
-#define FUNC_MUX_CTRL_A 0xfffe102C
-#define FUNC_MUX_CTRL_B 0xfffe1030
-#define FUNC_MUX_CTRL_C 0xfffe1034
-#define FUNC_MUX_CTRL_D 0xfffe1038
-#define PULL_DWN_CTRL_0 0xfffe1040
-#define PULL_DWN_CTRL_1 0xfffe1044
-#define PULL_DWN_CTRL_2 0xfffe1048
-#define PULL_DWN_CTRL_3 0xfffe104c
-#define PULL_DWN_CTRL_4 0xfffe10ac
-
-/* OMAP-1610 specific multiplexing registers */
-#define FUNC_MUX_CTRL_E 0xfffe1090
-#define FUNC_MUX_CTRL_F 0xfffe1094
-#define FUNC_MUX_CTRL_10 0xfffe1098
-#define FUNC_MUX_CTRL_11 0xfffe109c
-#define FUNC_MUX_CTRL_12 0xfffe10a0
-#define PU_PD_SEL_0 0xfffe10b4
-#define PU_PD_SEL_1 0xfffe10b8
-#define PU_PD_SEL_2 0xfffe10bc
-#define PU_PD_SEL_3 0xfffe10c0
-#define PU_PD_SEL_4 0xfffe10c4
-
/* Timer32K for 1610 and 1710*/
#define OMAP_TIMER32K_BASE 0xFFFBC400
@@ -299,15 +184,6 @@ static inline u32 omap_cs3_phys(void)
#define OMAP_LPG2_LCR (OMAP_LPG2_BASE + 0x00)
#define OMAP_LPG2_PMR (OMAP_LPG2_BASE + 0x04)
-/*
- * ----------------------------------------------------------------------------
- * Pulse-Width Light
- * ----------------------------------------------------------------------------
- */
-#define OMAP_PWL_BASE 0xfffb5800
-#define OMAP_PWL_ENABLE (OMAP_PWL_BASE + 0x00)
-#define OMAP_PWL_CLK_ENABLE (OMAP_PWL_BASE + 0x04)
-
/*
* ---------------------------------------------------------------------------
* Processor specific defines
@@ -7,6 +7,6 @@
#define __ASM_ARCH_MEMORY_H
/* REVISIT: omap1 legacy drivers still rely on this */
-#include <mach/soc.h>
+#include <mach/hardware.h>
#endif
@@ -20,6 +20,8 @@
#ifndef __ASM_ARCH_MUX_H
#define __ASM_ARCH_MUX_H
+#include <linux/soc/ti/omap1-mux.h>
+
#define PU_PD_SEL_NA 0 /* No pu_pd reg available */
#define PULL_DWN_CTRL_NA 0 /* No pull-down control needed */
@@ -124,301 +126,6 @@ struct pin_config {
};
-enum omap7xx_index {
- /* OMAP 730 keyboard */
- E2_7XX_KBR0,
- J7_7XX_KBR1,
- E1_7XX_KBR2,
- F3_7XX_KBR3,
- D2_7XX_KBR4,
- C2_7XX_KBC0,
- D3_7XX_KBC1,
- E4_7XX_KBC2,
- F4_7XX_KBC3,
- E3_7XX_KBC4,
-
- /* USB */
- AA17_7XX_USB_DM,
- W16_7XX_USB_PU_EN,
- W17_7XX_USB_VBUSI,
- W18_7XX_USB_DMCK_OUT,
- W19_7XX_USB_DCRST,
-
- /* MMC */
- MMC_7XX_CMD,
- MMC_7XX_CLK,
- MMC_7XX_DAT0,
-
- /* I2C */
- I2C_7XX_SCL,
- I2C_7XX_SDA,
-
- /* SPI */
- SPI_7XX_1,
- SPI_7XX_2,
- SPI_7XX_3,
- SPI_7XX_4,
- SPI_7XX_5,
- SPI_7XX_6,
-
- /* UART */
- UART_7XX_1,
- UART_7XX_2,
-};
-
-enum omap1xxx_index {
- /* UART1 (BT_UART_GATING)*/
- UART1_TX = 0,
- UART1_RTS,
-
- /* UART2 (COM_UART_GATING)*/
- UART2_TX,
- UART2_RX,
- UART2_CTS,
- UART2_RTS,
-
- /* UART3 (GIGA_UART_GATING) */
- UART3_TX,
- UART3_RX,
- UART3_CTS,
- UART3_RTS,
- UART3_CLKREQ,
- UART3_BCLK, /* 12MHz clock out */
- Y15_1610_UART3_RTS,
-
- /* PWT & PWL */
- PWT,
- PWL,
-
- /* USB master generic */
- R18_USB_VBUS,
- R18_1510_USB_GPIO0,
- W4_USB_PUEN,
- W4_USB_CLKO,
- W4_USB_HIGHZ,
- W4_GPIO58,
-
- /* USB1 master */
- USB1_SUSP,
- USB1_SEO,
- W13_1610_USB1_SE0,
- USB1_TXEN,
- USB1_TXD,
- USB1_VP,
- USB1_VM,
- USB1_RCV,
- USB1_SPEED,
- R13_1610_USB1_SPEED,
- R13_1710_USB1_SE0,
-
- /* USB2 master */
- USB2_SUSP,
- USB2_VP,
- USB2_TXEN,
- USB2_VM,
- USB2_RCV,
- USB2_SEO,
- USB2_TXD,
-
- /* OMAP-1510 GPIO */
- R18_1510_GPIO0,
- R19_1510_GPIO1,
- M14_1510_GPIO2,
-
- /* OMAP1610 GPIO */
- P18_1610_GPIO3,
- Y15_1610_GPIO17,
-
- /* OMAP-1710 GPIO */
- R18_1710_GPIO0,
- V2_1710_GPIO10,
- N21_1710_GPIO14,
- W15_1710_GPIO40,
-
- /* MPUIO */
- MPUIO2,
- N15_1610_MPUIO2,
- MPUIO4,
- MPUIO5,
- T20_1610_MPUIO5,
- W11_1610_MPUIO6,
- V10_1610_MPUIO7,
- W11_1610_MPUIO9,
- V10_1610_MPUIO10,
- W10_1610_MPUIO11,
- E20_1610_MPUIO13,
- U20_1610_MPUIO14,
- E19_1610_MPUIO15,
-
- /* MCBSP2 */
- MCBSP2_CLKR,
- MCBSP2_CLKX,
- MCBSP2_DR,
- MCBSP2_DX,
- MCBSP2_FSR,
- MCBSP2_FSX,
-
- /* MCBSP3 */
- MCBSP3_CLKX,
-
- /* Misc ballouts */
- BALLOUT_V8_ARMIO3,
- N20_HDQ,
-
- /* OMAP-1610 MMC2 */
- W8_1610_MMC2_DAT0,
- V8_1610_MMC2_DAT1,
- W15_1610_MMC2_DAT2,
- R10_1610_MMC2_DAT3,
- Y10_1610_MMC2_CLK,
- Y8_1610_MMC2_CMD,
- V9_1610_MMC2_CMDDIR,
- V5_1610_MMC2_DATDIR0,
- W19_1610_MMC2_DATDIR1,
- R18_1610_MMC2_CLKIN,
-
- /* OMAP-1610 External Trace Interface */
- M19_1610_ETM_PSTAT0,
- L15_1610_ETM_PSTAT1,
- L18_1610_ETM_PSTAT2,
- L19_1610_ETM_D0,
- J19_1610_ETM_D6,
- J18_1610_ETM_D7,
-
- /* OMAP16XX GPIO */
- P20_1610_GPIO4,
- V9_1610_GPIO7,
- W8_1610_GPIO9,
- N20_1610_GPIO11,
- N19_1610_GPIO13,
- P10_1610_GPIO22,
- V5_1610_GPIO24,
- AA20_1610_GPIO_41,
- W19_1610_GPIO48,
- M7_1610_GPIO62,
- V14_16XX_GPIO37,
- R9_16XX_GPIO18,
- L14_16XX_GPIO49,
-
- /* OMAP-1610 uWire */
- V19_1610_UWIRE_SCLK,
- U18_1610_UWIRE_SDI,
- W21_1610_UWIRE_SDO,
- N14_1610_UWIRE_CS0,
- P15_1610_UWIRE_CS3,
- N15_1610_UWIRE_CS1,
-
- /* OMAP-1610 SPI */
- U19_1610_SPIF_SCK,
- U18_1610_SPIF_DIN,
- P20_1610_SPIF_DIN,
- W21_1610_SPIF_DOUT,
- R18_1610_SPIF_DOUT,
- N14_1610_SPIF_CS0,
- N15_1610_SPIF_CS1,
- T19_1610_SPIF_CS2,
- P15_1610_SPIF_CS3,
-
- /* OMAP-1610 Flash */
- L3_1610_FLASH_CS2B_OE,
- M8_1610_FLASH_CS2B_WE,
-
- /* First MMC */
- MMC_CMD,
- MMC_DAT1,
- MMC_DAT2,
- MMC_DAT0,
- MMC_CLK,
- MMC_DAT3,
-
- /* OMAP-1710 MMC CMDDIR and DATDIR0 */
- M15_1710_MMC_CLKI,
- P19_1710_MMC_CMDDIR,
- P20_1710_MMC_DATDIR0,
-
- /* OMAP-1610 USB0 alternate pin configuration */
- W9_USB0_TXEN,
- AA9_USB0_VP,
- Y5_USB0_RCV,
- R9_USB0_VM,
- V6_USB0_TXD,
- W5_USB0_SE0,
- V9_USB0_SPEED,
- V9_USB0_SUSP,
-
- /* USB2 */
- W9_USB2_TXEN,
- AA9_USB2_VP,
- Y5_USB2_RCV,
- R9_USB2_VM,
- V6_USB2_TXD,
- W5_USB2_SE0,
-
- /* 16XX UART */
- R13_1610_UART1_TX,
- V14_16XX_UART1_RX,
- R14_1610_UART1_CTS,
- AA15_1610_UART1_RTS,
- R9_16XX_UART2_RX,
- L14_16XX_UART3_RX,
-
- /* I2C OMAP-1610 */
- I2C_SCL,
- I2C_SDA,
-
- /* Keypad */
- F18_1610_KBC0,
- D20_1610_KBC1,
- D19_1610_KBC2,
- E18_1610_KBC3,
- C21_1610_KBC4,
- G18_1610_KBR0,
- F19_1610_KBR1,
- H14_1610_KBR2,
- E20_1610_KBR3,
- E19_1610_KBR4,
- N19_1610_KBR5,
-
- /* Power management */
- T20_1610_LOW_PWR,
-
- /* MCLK Settings */
- V5_1710_MCLK_ON,
- V5_1710_MCLK_OFF,
- R10_1610_MCLK_ON,
- R10_1610_MCLK_OFF,
-
- /* CompactFlash controller */
- P11_1610_CF_CD2,
- R11_1610_CF_IOIS16,
- V10_1610_CF_IREQ,
- W10_1610_CF_RESET,
- W11_1610_CF_CD1,
-
- /* parallel camera */
- J15_1610_CAM_LCLK,
- J18_1610_CAM_D7,
- J19_1610_CAM_D6,
- J14_1610_CAM_D5,
- K18_1610_CAM_D4,
- K19_1610_CAM_D3,
- K15_1610_CAM_D2,
- K14_1610_CAM_D1,
- L19_1610_CAM_D0,
- L18_1610_CAM_VS,
- L15_1610_CAM_HS,
- M19_1610_CAM_RSTZ,
- Y15_1610_CAM_OUTCLK,
-
- /* serial camera */
- H19_1610_CAM_EXCLK,
- Y12_1610_CCP_CLKP,
- W13_1610_CCP_CLKM,
- W14_1610_CCP_DATAP,
- Y14_1610_CCP_DATAM,
-
-};
-
struct omap_mux_cfg {
struct pin_config *pins;
unsigned long size;
@@ -429,11 +136,9 @@ struct omap_mux_cfg {
/* setup pin muxing in Linux */
extern int omap1_mux_init(void);
extern int omap_mux_register(struct omap_mux_cfg *);
-extern int omap_cfg_reg(unsigned long reg_cfg);
#else
/* boot loader does it all (no warnings from CONFIG_OMAP_MUX_WARNINGS) */
static inline int omap1_mux_init(void) { return 0; }
-static inline int omap_cfg_reg(unsigned long reg_cfg) { return 0; }
#endif
extern int omap2_mux_init(void);
@@ -1,4 +1,6 @@
/*
- * We can move mach/soc.h here once the drivers are fixed
+ * We can move linux/soc/ti/omap1-soc.h here once the drivers are fixed
*/
-#include <mach/soc.h>
+#include <mach/hardware.h>
+#include <mach/irqs.h>
+#include <asm/irq.h>
@@ -35,7 +35,9 @@
#include <linux/omap-dma.h>
#ifdef CONFIG_ARCH_OMAP1
-#include <mach/soc.h>
+#include <mach/hardware.h>
+#include <linux/soc/ti/omap1-io.h>
+#include <linux/soc/ti/omap1-soc.h>
#endif
/*
new file mode 100644
@@ -0,0 +1,143 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+#ifndef __ASM_ARCH_OMAP_IO_H
+#define __ASM_ARCH_OMAP_IO_H
+
+#ifndef __ASSEMBLER__
+#include <linux/types.h>
+
+#if defined(CONFIG_ARCH_OMAP) && defined(CONFIG_ARCH_OMAP1)
+/*
+ * NOTE: Please use ioremap + __raw_read/write where possible instead of these
+ */
+extern u8 omap_readb(u32 pa);
+extern u16 omap_readw(u32 pa);
+extern u32 omap_readl(u32 pa);
+extern void omap_writeb(u8 v, u32 pa);
+extern void omap_writew(u16 v, u32 pa);
+extern void omap_writel(u32 v, u32 pa);
+#elif defined(CONFIG_COMPILE_TEST)
+static inline u8 omap_readb(u32 pa) { return 0; }
+static inline u16 omap_readw(u32 pa) { return 0; }
+static inline u32 omap_readl(u32 pa) { return 0; }
+static inline void omap_writeb(u8 v, u32 pa) { }
+static inline void omap_writew(u16 v, u32 pa) { }
+static inline void omap_writel(u32 v, u32 pa) { }
+#endif
+#endif
+
+/*
+ * ----------------------------------------------------------------------------
+ * System control registers
+ * ----------------------------------------------------------------------------
+ */
+#define MOD_CONF_CTRL_0 0xfffe1080
+#define MOD_CONF_CTRL_1 0xfffe1110
+
+/*
+ * ---------------------------------------------------------------------------
+ * UPLD
+ * ---------------------------------------------------------------------------
+ */
+#define ULPD_REG_BASE (0xfffe0800)
+#define ULPD_IT_STATUS (ULPD_REG_BASE + 0x14)
+#define ULPD_SETUP_ANALOG_CELL_3 (ULPD_REG_BASE + 0x24)
+#define ULPD_CLOCK_CTRL (ULPD_REG_BASE + 0x30)
+# define DIS_USB_PVCI_CLK (1 << 5) /* no USB/FAC synch */
+# define USB_MCLK_EN (1 << 4) /* enable W4_USB_CLKO */
+#define ULPD_SOFT_REQ (ULPD_REG_BASE + 0x34)
+# define SOFT_UDC_REQ (1 << 4)
+# define SOFT_USB_CLK_REQ (1 << 3)
+# define SOFT_DPLL_REQ (1 << 0)
+#define ULPD_DPLL_CTRL (ULPD_REG_BASE + 0x3c)
+#define ULPD_STATUS_REQ (ULPD_REG_BASE + 0x40)
+#define ULPD_APLL_CTRL (ULPD_REG_BASE + 0x4c)
+#define ULPD_POWER_CTRL (ULPD_REG_BASE + 0x50)
+#define ULPD_SOFT_DISABLE_REQ_REG (ULPD_REG_BASE + 0x68)
+# define DIS_MMC2_DPLL_REQ (1 << 11)
+# define DIS_MMC1_DPLL_REQ (1 << 10)
+# define DIS_UART3_DPLL_REQ (1 << 9)
+# define DIS_UART2_DPLL_REQ (1 << 8)
+# define DIS_UART1_DPLL_REQ (1 << 7)
+# define DIS_USB_HOST_DPLL_REQ (1 << 6)
+#define ULPD_SDW_CLK_DIV_CTRL_SEL (ULPD_REG_BASE + 0x74)
+#define ULPD_CAM_CLK_CTRL (ULPD_REG_BASE + 0x7c)
+
+/*
+ * ----------------------------------------------------------------------------
+ * Clocks
+ * ----------------------------------------------------------------------------
+ */
+#define CLKGEN_REG_BASE (0xfffece00)
+#define ARM_CKCTL (CLKGEN_REG_BASE + 0x0)
+#define ARM_IDLECT1 (CLKGEN_REG_BASE + 0x4)
+#define ARM_IDLECT2 (CLKGEN_REG_BASE + 0x8)
+#define ARM_EWUPCT (CLKGEN_REG_BASE + 0xC)
+#define ARM_RSTCT1 (CLKGEN_REG_BASE + 0x10)
+#define ARM_RSTCT2 (CLKGEN_REG_BASE + 0x14)
+#define ARM_SYSST (CLKGEN_REG_BASE + 0x18)
+#define ARM_IDLECT3 (CLKGEN_REG_BASE + 0x24)
+
+#define CK_RATEF 1
+#define CK_IDLEF 2
+#define CK_ENABLEF 4
+#define CK_SELECTF 8
+#define SETARM_IDLE_SHIFT
+
+/* DPLL control registers */
+#define DPLL_CTL (0xfffecf00)
+
+/* DSP clock control. Must use __raw_readw() and __raw_writew() with these */
+#define DSP_CONFIG_REG_BASE IOMEM(0xe1008000)
+#define DSP_CKCTL (DSP_CONFIG_REG_BASE + 0x0)
+#define DSP_IDLECT1 (DSP_CONFIG_REG_BASE + 0x4)
+#define DSP_IDLECT2 (DSP_CONFIG_REG_BASE + 0x8)
+#define DSP_RSTCT2 (DSP_CONFIG_REG_BASE + 0x14)
+
+/*
+ * ----------------------------------------------------------------------------
+ * Pulse-Width Light
+ * ----------------------------------------------------------------------------
+ */
+#define OMAP_PWL_BASE 0xfffb5800
+#define OMAP_PWL_ENABLE (OMAP_PWL_BASE + 0x00)
+#define OMAP_PWL_CLK_ENABLE (OMAP_PWL_BASE + 0x04)
+
+/*
+ * ----------------------------------------------------------------------------
+ * Pin multiplexing registers
+ * ----------------------------------------------------------------------------
+ */
+#define FUNC_MUX_CTRL_0 0xfffe1000
+#define FUNC_MUX_CTRL_1 0xfffe1004
+#define FUNC_MUX_CTRL_2 0xfffe1008
+#define COMP_MODE_CTRL_0 0xfffe100c
+#define FUNC_MUX_CTRL_3 0xfffe1010
+#define FUNC_MUX_CTRL_4 0xfffe1014
+#define FUNC_MUX_CTRL_5 0xfffe1018
+#define FUNC_MUX_CTRL_6 0xfffe101C
+#define FUNC_MUX_CTRL_7 0xfffe1020
+#define FUNC_MUX_CTRL_8 0xfffe1024
+#define FUNC_MUX_CTRL_9 0xfffe1028
+#define FUNC_MUX_CTRL_A 0xfffe102C
+#define FUNC_MUX_CTRL_B 0xfffe1030
+#define FUNC_MUX_CTRL_C 0xfffe1034
+#define FUNC_MUX_CTRL_D 0xfffe1038
+#define PULL_DWN_CTRL_0 0xfffe1040
+#define PULL_DWN_CTRL_1 0xfffe1044
+#define PULL_DWN_CTRL_2 0xfffe1048
+#define PULL_DWN_CTRL_3 0xfffe104c
+#define PULL_DWN_CTRL_4 0xfffe10ac
+
+/* OMAP-1610 specific multiplexing registers */
+#define FUNC_MUX_CTRL_E 0xfffe1090
+#define FUNC_MUX_CTRL_F 0xfffe1094
+#define FUNC_MUX_CTRL_10 0xfffe1098
+#define FUNC_MUX_CTRL_11 0xfffe109c
+#define FUNC_MUX_CTRL_12 0xfffe10a0
+#define PU_PD_SEL_0 0xfffe10b4
+#define PU_PD_SEL_1 0xfffe10b8
+#define PU_PD_SEL_2 0xfffe10bc
+#define PU_PD_SEL_3 0xfffe10c0
+#define PU_PD_SEL_4 0xfffe10c4
+
+#endif
new file mode 100644
@@ -0,0 +1,311 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+#ifndef __SOC_TI_OMAP1_MUX_H
+#define __SOC_TI_OMAP1_MUX_H
+/*
+ * This should not really be a global header, it reflects the
+ * traditional way that omap1 does pin muxing without the
+ * pinctrl subsystem.
+ */
+
+enum omap7xx_index {
+ /* OMAP 730 keyboard */
+ E2_7XX_KBR0,
+ J7_7XX_KBR1,
+ E1_7XX_KBR2,
+ F3_7XX_KBR3,
+ D2_7XX_KBR4,
+ C2_7XX_KBC0,
+ D3_7XX_KBC1,
+ E4_7XX_KBC2,
+ F4_7XX_KBC3,
+ E3_7XX_KBC4,
+
+ /* USB */
+ AA17_7XX_USB_DM,
+ W16_7XX_USB_PU_EN,
+ W17_7XX_USB_VBUSI,
+ W18_7XX_USB_DMCK_OUT,
+ W19_7XX_USB_DCRST,
+
+ /* MMC */
+ MMC_7XX_CMD,
+ MMC_7XX_CLK,
+ MMC_7XX_DAT0,
+
+ /* I2C */
+ I2C_7XX_SCL,
+ I2C_7XX_SDA,
+
+ /* SPI */
+ SPI_7XX_1,
+ SPI_7XX_2,
+ SPI_7XX_3,
+ SPI_7XX_4,
+ SPI_7XX_5,
+ SPI_7XX_6,
+
+ /* UART */
+ UART_7XX_1,
+ UART_7XX_2,
+};
+
+enum omap1xxx_index {
+ /* UART1 (BT_UART_GATING)*/
+ UART1_TX = 0,
+ UART1_RTS,
+
+ /* UART2 (COM_UART_GATING)*/
+ UART2_TX,
+ UART2_RX,
+ UART2_CTS,
+ UART2_RTS,
+
+ /* UART3 (GIGA_UART_GATING) */
+ UART3_TX,
+ UART3_RX,
+ UART3_CTS,
+ UART3_RTS,
+ UART3_CLKREQ,
+ UART3_BCLK, /* 12MHz clock out */
+ Y15_1610_UART3_RTS,
+
+ /* PWT & PWL */
+ PWT,
+ PWL,
+
+ /* USB master generic */
+ R18_USB_VBUS,
+ R18_1510_USB_GPIO0,
+ W4_USB_PUEN,
+ W4_USB_CLKO,
+ W4_USB_HIGHZ,
+ W4_GPIO58,
+
+ /* USB1 master */
+ USB1_SUSP,
+ USB1_SEO,
+ W13_1610_USB1_SE0,
+ USB1_TXEN,
+ USB1_TXD,
+ USB1_VP,
+ USB1_VM,
+ USB1_RCV,
+ USB1_SPEED,
+ R13_1610_USB1_SPEED,
+ R13_1710_USB1_SE0,
+
+ /* USB2 master */
+ USB2_SUSP,
+ USB2_VP,
+ USB2_TXEN,
+ USB2_VM,
+ USB2_RCV,
+ USB2_SEO,
+ USB2_TXD,
+
+ /* OMAP-1510 GPIO */
+ R18_1510_GPIO0,
+ R19_1510_GPIO1,
+ M14_1510_GPIO2,
+
+ /* OMAP1610 GPIO */
+ P18_1610_GPIO3,
+ Y15_1610_GPIO17,
+
+ /* OMAP-1710 GPIO */
+ R18_1710_GPIO0,
+ V2_1710_GPIO10,
+ N21_1710_GPIO14,
+ W15_1710_GPIO40,
+
+ /* MPUIO */
+ MPUIO2,
+ N15_1610_MPUIO2,
+ MPUIO4,
+ MPUIO5,
+ T20_1610_MPUIO5,
+ W11_1610_MPUIO6,
+ V10_1610_MPUIO7,
+ W11_1610_MPUIO9,
+ V10_1610_MPUIO10,
+ W10_1610_MPUIO11,
+ E20_1610_MPUIO13,
+ U20_1610_MPUIO14,
+ E19_1610_MPUIO15,
+
+ /* MCBSP2 */
+ MCBSP2_CLKR,
+ MCBSP2_CLKX,
+ MCBSP2_DR,
+ MCBSP2_DX,
+ MCBSP2_FSR,
+ MCBSP2_FSX,
+
+ /* MCBSP3 */
+ MCBSP3_CLKX,
+
+ /* Misc ballouts */
+ BALLOUT_V8_ARMIO3,
+ N20_HDQ,
+
+ /* OMAP-1610 MMC2 */
+ W8_1610_MMC2_DAT0,
+ V8_1610_MMC2_DAT1,
+ W15_1610_MMC2_DAT2,
+ R10_1610_MMC2_DAT3,
+ Y10_1610_MMC2_CLK,
+ Y8_1610_MMC2_CMD,
+ V9_1610_MMC2_CMDDIR,
+ V5_1610_MMC2_DATDIR0,
+ W19_1610_MMC2_DATDIR1,
+ R18_1610_MMC2_CLKIN,
+
+ /* OMAP-1610 External Trace Interface */
+ M19_1610_ETM_PSTAT0,
+ L15_1610_ETM_PSTAT1,
+ L18_1610_ETM_PSTAT2,
+ L19_1610_ETM_D0,
+ J19_1610_ETM_D6,
+ J18_1610_ETM_D7,
+
+ /* OMAP16XX GPIO */
+ P20_1610_GPIO4,
+ V9_1610_GPIO7,
+ W8_1610_GPIO9,
+ N20_1610_GPIO11,
+ N19_1610_GPIO13,
+ P10_1610_GPIO22,
+ V5_1610_GPIO24,
+ AA20_1610_GPIO_41,
+ W19_1610_GPIO48,
+ M7_1610_GPIO62,
+ V14_16XX_GPIO37,
+ R9_16XX_GPIO18,
+ L14_16XX_GPIO49,
+
+ /* OMAP-1610 uWire */
+ V19_1610_UWIRE_SCLK,
+ U18_1610_UWIRE_SDI,
+ W21_1610_UWIRE_SDO,
+ N14_1610_UWIRE_CS0,
+ P15_1610_UWIRE_CS3,
+ N15_1610_UWIRE_CS1,
+
+ /* OMAP-1610 SPI */
+ U19_1610_SPIF_SCK,
+ U18_1610_SPIF_DIN,
+ P20_1610_SPIF_DIN,
+ W21_1610_SPIF_DOUT,
+ R18_1610_SPIF_DOUT,
+ N14_1610_SPIF_CS0,
+ N15_1610_SPIF_CS1,
+ T19_1610_SPIF_CS2,
+ P15_1610_SPIF_CS3,
+
+ /* OMAP-1610 Flash */
+ L3_1610_FLASH_CS2B_OE,
+ M8_1610_FLASH_CS2B_WE,
+
+ /* First MMC */
+ MMC_CMD,
+ MMC_DAT1,
+ MMC_DAT2,
+ MMC_DAT0,
+ MMC_CLK,
+ MMC_DAT3,
+
+ /* OMAP-1710 MMC CMDDIR and DATDIR0 */
+ M15_1710_MMC_CLKI,
+ P19_1710_MMC_CMDDIR,
+ P20_1710_MMC_DATDIR0,
+
+ /* OMAP-1610 USB0 alternate pin configuration */
+ W9_USB0_TXEN,
+ AA9_USB0_VP,
+ Y5_USB0_RCV,
+ R9_USB0_VM,
+ V6_USB0_TXD,
+ W5_USB0_SE0,
+ V9_USB0_SPEED,
+ V9_USB0_SUSP,
+
+ /* USB2 */
+ W9_USB2_TXEN,
+ AA9_USB2_VP,
+ Y5_USB2_RCV,
+ R9_USB2_VM,
+ V6_USB2_TXD,
+ W5_USB2_SE0,
+
+ /* 16XX UART */
+ R13_1610_UART1_TX,
+ V14_16XX_UART1_RX,
+ R14_1610_UART1_CTS,
+ AA15_1610_UART1_RTS,
+ R9_16XX_UART2_RX,
+ L14_16XX_UART3_RX,
+
+ /* I2C OMAP-1610 */
+ I2C_SCL,
+ I2C_SDA,
+
+ /* Keypad */
+ F18_1610_KBC0,
+ D20_1610_KBC1,
+ D19_1610_KBC2,
+ E18_1610_KBC3,
+ C21_1610_KBC4,
+ G18_1610_KBR0,
+ F19_1610_KBR1,
+ H14_1610_KBR2,
+ E20_1610_KBR3,
+ E19_1610_KBR4,
+ N19_1610_KBR5,
+
+ /* Power management */
+ T20_1610_LOW_PWR,
+
+ /* MCLK Settings */
+ V5_1710_MCLK_ON,
+ V5_1710_MCLK_OFF,
+ R10_1610_MCLK_ON,
+ R10_1610_MCLK_OFF,
+
+ /* CompactFlash controller */
+ P11_1610_CF_CD2,
+ R11_1610_CF_IOIS16,
+ V10_1610_CF_IREQ,
+ W10_1610_CF_RESET,
+ W11_1610_CF_CD1,
+
+ /* parallel camera */
+ J15_1610_CAM_LCLK,
+ J18_1610_CAM_D7,
+ J19_1610_CAM_D6,
+ J14_1610_CAM_D5,
+ K18_1610_CAM_D4,
+ K19_1610_CAM_D3,
+ K15_1610_CAM_D2,
+ K14_1610_CAM_D1,
+ L19_1610_CAM_D0,
+ L18_1610_CAM_VS,
+ L15_1610_CAM_HS,
+ M19_1610_CAM_RSTZ,
+ Y15_1610_CAM_OUTCLK,
+
+ /* serial camera */
+ H19_1610_CAM_EXCLK,
+ Y12_1610_CCP_CLKP,
+ W13_1610_CCP_CLKM,
+ W14_1610_CCP_DATAP,
+ Y14_1610_CCP_DATAM,
+
+};
+
+#ifdef CONFIG_OMAP_MUX
+extern int omap_cfg_reg(unsigned long reg_cfg);
+#else
+static inline int omap_cfg_reg(unsigned long reg_cfg) { return 0; }
+#endif
+
+#endif
similarity index 90%
rename from arch/arm/mach-omap1/include/mach/soc.h
rename to include/linux/soc/ti/omap1-soc.h
@@ -14,14 +14,6 @@
#ifndef __ASM_ARCH_OMAP_CPU_H
#define __ASM_ARCH_OMAP_CPU_H
-#include <asm/irq.h>
-#include <mach/hardware.h>
-#include <mach/irqs.h>
-
-#ifndef __ASSEMBLY__
-
-#include <linux/bitops.h>
-
/*
* Test if multicore OMAP support is needed
*/
@@ -176,20 +168,7 @@ IS_OMAP_TYPE(1710, 0x1710)
#define cpu_is_omap1621() 0
#define cpu_is_omap1710() 0
-/* These are needed to compile common code */
-#ifdef CONFIG_ARCH_OMAP1
-#define cpu_is_omap242x() 0
-#define cpu_is_omap2430() 0
-#define cpu_is_omap243x() 0
-#define cpu_is_omap24xx() 0
-#define cpu_is_omap34xx() 0
-#define cpu_is_omap44xx() 0
-#define soc_is_omap54xx() 0
-#define soc_is_dra7xx() 0
-#define soc_is_am33xx() 0
#define cpu_class_is_omap1() 1
-#define cpu_class_is_omap2() 0
-#endif
/*
* Whether we have MULTI_OMAP1 or not, we still need to distinguish
@@ -216,5 +195,4 @@ IS_OMAP_TYPE(1710, 0x1710)
# define cpu_is_omap1710() is_omap1710()
#endif
-#endif /* __ASSEMBLY__ */
#endif