@@ -6,7 +6,7 @@
*/
#include <linux/clkdev.h>
#include <linux/irq.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/gpio/machine.h>
#include <linux/gpio/property.h>
#include <linux/kernel.h>
@@ -250,19 +250,25 @@ static struct i2c_board_info nokia770_i2c_board_info_2[] __initdata = {
static void __init nokia770_cbus_init(void)
{
- const int retu_irq_gpio = 62;
- const int tahvo_irq_gpio = 40;
-
- if (gpio_request_one(retu_irq_gpio, GPIOF_IN, "Retu IRQ"))
- return;
- if (gpio_request_one(tahvo_irq_gpio, GPIOF_IN, "Tahvo IRQ")) {
- gpio_free(retu_irq_gpio);
- return;
+ struct gpio_desc *d;
+ int irq;
+
+ d = gpiod_get(NULL, "retu_irq", GPIOD_IN);
+ if (IS_ERR(d)) {
+ pr_err("Unable to get CBUS Retu IRQ GPIO descriptor\n");
+ } else {
+ irq = gpiod_to_irq(d);
+ irq_set_irq_type(irq, IRQ_TYPE_EDGE_RISING);
+ nokia770_i2c_board_info_2[0].irq = irq;
+ }
+ d = gpiod_get(NULL, "tahvo_irq", GPIOD_IN);
+ if (IS_ERR(d)) {
+ pr_err("Unable to get CBUS Tahvo IRQ GPIO descriptor\n");
+ } else {
+ irq = gpiod_to_irq(d);
+ irq_set_irq_type(irq, IRQ_TYPE_EDGE_RISING);
+ nokia770_i2c_board_info_2[1].irq = irq;
}
- irq_set_irq_type(gpio_to_irq(retu_irq_gpio), IRQ_TYPE_EDGE_RISING);
- irq_set_irq_type(gpio_to_irq(tahvo_irq_gpio), IRQ_TYPE_EDGE_RISING);
- nokia770_i2c_board_info_2[0].irq = gpio_to_irq(retu_irq_gpio);
- nokia770_i2c_board_info_2[1].irq = gpio_to_irq(tahvo_irq_gpio);
i2c_register_board_info(2, nokia770_i2c_board_info_2,
ARRAY_SIZE(nokia770_i2c_board_info_2));
device_create_managed_software_node(&nokia770_cbus_device.dev,
@@ -275,8 +281,25 @@ static void __init nokia770_cbus_init(void)
}
#endif /* CONFIG_I2C_CBUS_GPIO */
+static struct gpiod_lookup_table nokia770_irq_gpio_table = {
+ .dev_id = NULL,
+ .table = {
+ /* GPIO used by SPI device 1 */
+ GPIO_LOOKUP("gpio-0-15", 15, "ads7846_irq",
+ GPIO_ACTIVE_HIGH),
+ /* GPIO used for retu IRQ */
+ GPIO_LOOKUP("gpio-48-63", 15, "retu_irq",
+ GPIO_ACTIVE_HIGH),
+ /* GPIO used for tahvo IRQ */
+ GPIO_LOOKUP("gpio-32-47", 8, "tahvo_irq",
+ GPIO_ACTIVE_HIGH),
+ },
+};
+
static void __init omap_nokia770_init(void)
{
+ struct gpio_desc *d;
+
/* On Nokia 770, the SleepX signal is masked with an
* MPUIO line by default. It has to be unmasked for it
* to become functional */
@@ -288,6 +311,14 @@ static void __init omap_nokia770_init(void)
software_node_register_node_group(nokia770_gpiochip_nodes);
platform_add_devices(nokia770_devices, ARRAY_SIZE(nokia770_devices));
+
+ gpiod_add_lookup_table(&nokia770_irq_gpio_table);
+ d = gpiod_get(NULL, "ads7846_irq", GPIOD_IN);
+ if (IS_ERR(d))
+ pr_err("Unable to get ADS7846 IRQ GPIO descriptor\n");
+ else
+ nokia770_spi_board_info[1].irq = gpiod_to_irq(d);
+
spi_register_board_info(nokia770_spi_board_info,
ARRAY_SIZE(nokia770_spi_board_info));
omap_serial_init();
The platform devices on the Nokia 770 is using some board-specific IRQs that get statically assigned to platform devices in the boardfile. This does not work with dynamic IRQ chip bases. Utilize the NULL device to define some board-specific GPIO lookups and use these to immediately look up the same GPIOs, convert to IRQ numbers and pass as resources to the devices. This is ugly but should work. Fixes: 92bf78b33b0b ("gpio: omap: use dynamic allocation of base") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- arch/arm/mach-omap1/board-nokia770.c | 57 ++++++++++++++++++++++++++++-------- 1 file changed, 44 insertions(+), 13 deletions(-)