@@ -22,10 +22,10 @@
#define TIMEOUT_US 2000 /* CVP STATUS timeout for USERMODE polling */
/* Vendor Specific Extended Capability Registers */
-#define VSE_PCIE_EXT_CAP_ID 0x200
+#define VSE_PCIE_EXT_CAP_ID 0x0
#define VSE_PCIE_EXT_CAP_ID_VAL 0x000b /* 16bit */
-#define VSE_CVP_STATUS 0x21c /* 32bit */
+#define VSE_CVP_STATUS 0x1c /* 32bit */
#define VSE_CVP_STATUS_CFG_RDY BIT(18) /* CVP_CONFIG_READY */
#define VSE_CVP_STATUS_CFG_ERR BIT(19) /* CVP_CONFIG_ERROR */
#define VSE_CVP_STATUS_CVP_EN BIT(20) /* ctrl block is enabling CVP */
@@ -33,18 +33,18 @@
#define VSE_CVP_STATUS_CFG_DONE BIT(23) /* CVP_CONFIG_DONE */
#define VSE_CVP_STATUS_PLD_CLK_IN_USE BIT(24) /* PLD_CLK_IN_USE */
-#define VSE_CVP_MODE_CTRL 0x220 /* 32bit */
+#define VSE_CVP_MODE_CTRL 0x20 /* 32bit */
#define VSE_CVP_MODE_CTRL_CVP_MODE BIT(0) /* CVP (1) or normal mode (0) */
#define VSE_CVP_MODE_CTRL_HIP_CLK_SEL BIT(1) /* PMA (1) or fabric clock (0) */
#define VSE_CVP_MODE_CTRL_NUMCLKS_OFF 8 /* NUMCLKS bits offset */
#define VSE_CVP_MODE_CTRL_NUMCLKS_MASK GENMASK(15, 8)
-#define VSE_CVP_DATA 0x228 /* 32bit */
-#define VSE_CVP_PROG_CTRL 0x22c /* 32bit */
+#define VSE_CVP_DATA 0x28 /* 32bit */
+#define VSE_CVP_PROG_CTRL 0x2c /* 32bit */
#define VSE_CVP_PROG_CTRL_CONFIG BIT(0)
#define VSE_CVP_PROG_CTRL_START_XFER BIT(1)
-#define VSE_UNCOR_ERR_STATUS 0x234 /* 32bit */
+#define VSE_UNCOR_ERR_STATUS 0x34 /* 32bit */
#define VSE_UNCOR_ERR_CVP_CFG_ERR BIT(5) /* CVP_CONFIG_ERROR_LATCHED */
#define DRV_NAME "altera-cvp"
@@ -60,14 +60,27 @@ struct altera_cvp_conf {
void (*write_data)(struct altera_cvp_conf *, u32);
char mgr_name[64];
u8 numclks;
+ u32 vsec_offset;
};
+static void altera_read_config_dword(struct altera_cvp_conf *conf,
+ int where, u32 *val)
+{
+ pci_read_config_dword(conf->pci_dev, conf->vsec_offset + where, val);
+}
+
+static void altera_write_config_dword(struct altera_cvp_conf *conf,
+ int where, u32 val)
+{
+ pci_write_config_dword(conf->pci_dev, conf->vsec_offset + where, val);
+}
+
static enum fpga_mgr_states altera_cvp_state(struct fpga_manager *mgr)
{
struct altera_cvp_conf *conf = mgr->priv;
u32 status;
- pci_read_config_dword(conf->pci_dev, VSE_CVP_STATUS, &status);
+ altera_read_config_dword(conf, VSE_CVP_STATUS, &status);
if (status & VSE_CVP_STATUS_CFG_DONE)
return FPGA_MGR_STATE_OPERATING;
@@ -85,7 +98,8 @@ static void altera_cvp_write_data_iomem(struct altera_cvp_conf *conf, u32 val)
static void altera_cvp_write_data_config(struct altera_cvp_conf *conf, u32 val)
{
- pci_write_config_dword(conf->pci_dev, VSE_CVP_DATA, val);
+ pci_write_config_dword(conf->pci_dev, conf->vsec_offset + VSE_CVP_DATA,
+ val);
}
/* switches between CvP clock and internal clock */
@@ -95,10 +109,10 @@ static void altera_cvp_dummy_write(struct altera_cvp_conf *conf)
u32 val;
/* set 1 CVP clock cycle for every CVP Data Register Write */
- pci_read_config_dword(conf->pci_dev, VSE_CVP_MODE_CTRL, &val);
+ altera_read_config_dword(conf, VSE_CVP_MODE_CTRL, &val);
val &= ~VSE_CVP_MODE_CTRL_NUMCLKS_MASK;
val |= 1 << VSE_CVP_MODE_CTRL_NUMCLKS_OFF;
- pci_write_config_dword(conf->pci_dev, VSE_CVP_MODE_CTRL, val);
+ altera_write_config_dword(conf, VSE_CVP_MODE_CTRL, val);
for (i = 0; i < CVP_DUMMY_WR; i++)
conf->write_data(conf, 0); /* dummy data, could be any value */
@@ -115,7 +129,7 @@ static int altera_cvp_wait_status(struct altera_cvp_conf *conf, u32 status_mask,
retries++;
do {
- pci_read_config_dword(conf->pci_dev, VSE_CVP_STATUS, &val);
+ altera_read_config_dword(conf, VSE_CVP_STATUS, &val);
if ((val & status_mask) == status_val)
return 0;
@@ -130,18 +144,17 @@ static int altera_cvp_teardown(struct fpga_manager *mgr,
struct fpga_image_info *info)
{
struct altera_cvp_conf *conf = mgr->priv;
- struct pci_dev *pdev = conf->pci_dev;
int ret;
u32 val;
/* STEP 12 - reset START_XFER bit */
- pci_read_config_dword(pdev, VSE_CVP_PROG_CTRL, &val);
+ altera_read_config_dword(conf, VSE_CVP_PROG_CTRL, &val);
val &= ~VSE_CVP_PROG_CTRL_START_XFER;
- pci_write_config_dword(pdev, VSE_CVP_PROG_CTRL, val);
+ altera_write_config_dword(conf, VSE_CVP_PROG_CTRL, val);
/* STEP 13 - reset CVP_CONFIG bit */
val &= ~VSE_CVP_PROG_CTRL_CONFIG;
- pci_write_config_dword(pdev, VSE_CVP_PROG_CTRL, val);
+ altera_write_config_dword(conf, VSE_CVP_PROG_CTRL, val);
/*
* STEP 14
@@ -163,7 +176,6 @@ static int altera_cvp_write_init(struct fpga_manager *mgr,
const char *buf, size_t count)
{
struct altera_cvp_conf *conf = mgr->priv;
- struct pci_dev *pdev = conf->pci_dev;
u32 iflags, val;
int ret;
@@ -183,7 +195,7 @@ static int altera_cvp_write_init(struct fpga_manager *mgr,
conf->numclks = 1; /* for uncompressed and unencrypted images */
/* STEP 1 - read CVP status and check CVP_EN flag */
- pci_read_config_dword(pdev, VSE_CVP_STATUS, &val);
+ altera_read_config_dword(conf, VSE_CVP_STATUS, &val);
if (!(val & VSE_CVP_STATUS_CVP_EN)) {
dev_err(&mgr->dev, "CVP mode off: 0x%04x\n", val);
return -ENODEV;
@@ -201,14 +213,14 @@ static int altera_cvp_write_init(struct fpga_manager *mgr,
* - set HIP_CLK_SEL and CVP_MODE (must be set in the order mentioned)
*/
/* switch from fabric to PMA clock */
- pci_read_config_dword(pdev, VSE_CVP_MODE_CTRL, &val);
+ altera_read_config_dword(conf, VSE_CVP_MODE_CTRL, &val);
val |= VSE_CVP_MODE_CTRL_HIP_CLK_SEL;
- pci_write_config_dword(pdev, VSE_CVP_MODE_CTRL, val);
+ altera_write_config_dword(conf, VSE_CVP_MODE_CTRL, val);
/* set CVP mode */
- pci_read_config_dword(pdev, VSE_CVP_MODE_CTRL, &val);
+ altera_read_config_dword(conf, VSE_CVP_MODE_CTRL, &val);
val |= VSE_CVP_MODE_CTRL_CVP_MODE;
- pci_write_config_dword(pdev, VSE_CVP_MODE_CTRL, val);
+ altera_write_config_dword(conf, VSE_CVP_MODE_CTRL, val);
/*
* STEP 3
@@ -217,10 +229,10 @@ static int altera_cvp_write_init(struct fpga_manager *mgr,
altera_cvp_dummy_write(conf);
/* STEP 4 - set CVP_CONFIG bit */
- pci_read_config_dword(pdev, VSE_CVP_PROG_CTRL, &val);
+ altera_read_config_dword(conf, VSE_CVP_PROG_CTRL, &val);
/* request control block to begin transfer using CVP */
val |= VSE_CVP_PROG_CTRL_CONFIG;
- pci_write_config_dword(pdev, VSE_CVP_PROG_CTRL, val);
+ altera_write_config_dword(conf, VSE_CVP_PROG_CTRL, val);
/* STEP 5 - poll CVP_CONFIG READY for 1 with 10us timeout */
ret = altera_cvp_wait_status(conf, VSE_CVP_STATUS_CFG_RDY,
@@ -237,15 +249,15 @@ static int altera_cvp_write_init(struct fpga_manager *mgr,
altera_cvp_dummy_write(conf);
/* STEP 7 - set START_XFER */
- pci_read_config_dword(pdev, VSE_CVP_PROG_CTRL, &val);
+ altera_read_config_dword(conf, VSE_CVP_PROG_CTRL, &val);
val |= VSE_CVP_PROG_CTRL_START_XFER;
- pci_write_config_dword(pdev, VSE_CVP_PROG_CTRL, val);
+ altera_write_config_dword(conf, VSE_CVP_PROG_CTRL, val);
/* STEP 8 - start transfer (set CVP_NUMCLKS for bitstream) */
- pci_read_config_dword(pdev, VSE_CVP_MODE_CTRL, &val);
+ altera_read_config_dword(conf, VSE_CVP_MODE_CTRL, &val);
val &= ~VSE_CVP_MODE_CTRL_NUMCLKS_MASK;
val |= conf->numclks << VSE_CVP_MODE_CTRL_NUMCLKS_OFF;
- pci_write_config_dword(pdev, VSE_CVP_MODE_CTRL, val);
+ altera_write_config_dword(conf, VSE_CVP_MODE_CTRL, val);
return 0;
}
@@ -256,7 +268,7 @@ static inline int altera_cvp_chk_error(struct fpga_manager *mgr, size_t bytes)
u32 val;
/* STEP 10 (optional) - check CVP_CONFIG_ERROR flag */
- pci_read_config_dword(conf->pci_dev, VSE_CVP_STATUS, &val);
+ altera_read_config_dword(conf, VSE_CVP_STATUS, &val);
if (val & VSE_CVP_STATUS_CFG_ERR) {
dev_err(&mgr->dev, "CVP_CONFIG_ERROR after %zu bytes!\n",
bytes);
@@ -315,27 +327,25 @@ static int altera_cvp_write_complete(struct fpga_manager *mgr,
struct fpga_image_info *info)
{
struct altera_cvp_conf *conf = mgr->priv;
- struct pci_dev *pdev = conf->pci_dev;
+ u32 mask, val;
int ret;
- u32 mask;
- u32 val;
ret = altera_cvp_teardown(mgr, info);
if (ret)
return ret;
/* STEP 16 - check CVP_CONFIG_ERROR_LATCHED bit */
- pci_read_config_dword(pdev, VSE_UNCOR_ERR_STATUS, &val);
+ altera_read_config_dword(conf, VSE_UNCOR_ERR_STATUS, &val);
if (val & VSE_UNCOR_ERR_CVP_CFG_ERR) {
dev_err(&mgr->dev, "detected CVP_CONFIG_ERROR_LATCHED!\n");
return -EPROTO;
}
/* STEP 17 - reset CVP_MODE and HIP_CLK_SEL bit */
- pci_read_config_dword(pdev, VSE_CVP_MODE_CTRL, &val);
+ altera_read_config_dword(conf, VSE_CVP_MODE_CTRL, &val);
val &= ~VSE_CVP_MODE_CTRL_HIP_CLK_SEL;
val &= ~VSE_CVP_MODE_CTRL_CVP_MODE;
- pci_write_config_dword(pdev, VSE_CVP_MODE_CTRL, val);
+ altera_write_config_dword(conf, VSE_CVP_MODE_CTRL, val);
/* STEP 18 - poll PLD_CLK_IN_USE and USER_MODE bits */
mask = VSE_CVP_STATUS_PLD_CLK_IN_USE | VSE_CVP_STATUS_USERMODE;
@@ -394,22 +404,29 @@ static int altera_cvp_probe(struct pci_dev *pdev,
{
struct altera_cvp_conf *conf;
struct fpga_manager *mgr;
+ int ret, offset;
u16 cmd, val;
u32 regval;
- int ret;
+
+ /* Discover the Vendor Specific Offset for this device */
+ offset = pci_find_next_ext_capability(pdev, 0, PCI_EXT_CAP_ID_VNDR);
+ if (!offset) {
+ dev_err(&pdev->dev, "No Vendor Specific Offset.\n");
+ return -ENODEV;
+ }
/*
* First check if this is the expected FPGA device. PCI config
* space access works without enabling the PCI device, memory
* space access is enabled further down.
*/
- pci_read_config_word(pdev, VSE_PCIE_EXT_CAP_ID, &val);
+ pci_read_config_word(pdev, offset + VSE_PCIE_EXT_CAP_ID, &val);
if (val != VSE_PCIE_EXT_CAP_ID_VAL) {
dev_err(&pdev->dev, "Wrong EXT_CAP_ID value 0x%x\n", val);
return -ENODEV;
}
- pci_read_config_dword(pdev, VSE_CVP_STATUS, ®val);
+ pci_read_config_dword(pdev, offset + VSE_CVP_STATUS, ®val);
if (!(regval & VSE_CVP_STATUS_CVP_EN)) {
dev_err(&pdev->dev,
"CVP is disabled for this device: CVP_STATUS Reg 0x%x\n",
@@ -421,6 +438,9 @@ static int altera_cvp_probe(struct pci_dev *pdev,
if (!conf)
return -ENOMEM;
+ conf->vsec_offset = offset;
+ dev_dbg(&pdev->dev, "Vendor Specific Data Offset at 0x%x\n", offset);
+
/*
* Enable memory BAR access. We cannot use pci_enable_device() here
* because it will make the driver unusable with FPGA devices that