@@ -181,7 +181,315 @@ static const struct attribute_group *m10bmc_sec_attr_groups[] = {
NULL,
};
-static const struct fpga_sec_mgr_ops m10bmc_sops = { };
+static void log_error_regs(struct m10bmc_sec *sec, u32 doorbell)
+{
+ u32 auth_result;
+
+ dev_err(sec->dev, "RSU error status: 0x%08x\n", doorbell);
+
+ if (!m10bmc_sys_read(sec->m10bmc, M10BMC_AUTH_RESULT, &auth_result))
+ dev_err(sec->dev, "RSU auth result: 0x%08x\n", auth_result);
+}
+
+static enum fpga_sec_err rsu_check_idle(struct m10bmc_sec *sec)
+{
+ u32 doorbell;
+ int ret;
+
+ ret = m10bmc_sys_read(sec->m10bmc, M10BMC_DOORBELL, &doorbell);
+ if (ret)
+ return FPGA_SEC_ERR_RW_ERROR;
+
+ if (rsu_prog(doorbell) != RSU_PROG_IDLE &&
+ rsu_prog(doorbell) != RSU_PROG_RSU_DONE) {
+ log_error_regs(sec, doorbell);
+ return FPGA_SEC_ERR_BUSY;
+ }
+
+ return FPGA_SEC_ERR_NONE;
+}
+
+static inline bool rsu_start_done(u32 doorbell)
+{
+ u32 status, progress;
+
+ if (doorbell & DRBL_RSU_REQUEST)
+ return false;
+
+ status = rsu_stat(doorbell);
+ if (status == RSU_STAT_ERASE_FAIL || status == RSU_STAT_WEAROUT)
+ return true;
+
+ progress = rsu_prog(doorbell);
+ if (progress != RSU_PROG_IDLE && progress != RSU_PROG_RSU_DONE)
+ return true;
+
+ return false;
+}
+
+static enum fpga_sec_err rsu_update_init(struct m10bmc_sec *sec)
+{
+ u32 doorbell, status;
+ int ret;
+
+ ret = regmap_update_bits(sec->m10bmc->regmap,
+ M10BMC_SYS_BASE + M10BMC_DOORBELL,
+ DRBL_RSU_REQUEST | DRBL_HOST_STATUS,
+ DRBL_RSU_REQUEST |
+ FIELD_PREP(DRBL_HOST_STATUS,
+ HOST_STATUS_IDLE));
+ if (ret)
+ return FPGA_SEC_ERR_RW_ERROR;
+
+ ret = regmap_read_poll_timeout(sec->m10bmc->regmap,
+ M10BMC_SYS_BASE + M10BMC_DOORBELL,
+ doorbell,
+ rsu_start_done(doorbell),
+ NIOS_HANDSHAKE_INTERVAL_US,
+ NIOS_HANDSHAKE_TIMEOUT_US);
+
+ if (ret == -ETIMEDOUT) {
+ log_error_regs(sec, doorbell);
+ return FPGA_SEC_ERR_TIMEOUT;
+ } else if (ret) {
+ return FPGA_SEC_ERR_RW_ERROR;
+ }
+
+ status = rsu_stat(doorbell);
+ if (status == RSU_STAT_WEAROUT) {
+ dev_warn(sec->dev, "Excessive flash update count detected\n");
+ return FPGA_SEC_ERR_WEAROUT;
+ } else if (status == RSU_STAT_ERASE_FAIL) {
+ log_error_regs(sec, doorbell);
+ return FPGA_SEC_ERR_HW_ERROR;
+ }
+
+ return FPGA_SEC_ERR_NONE;
+}
+
+static enum fpga_sec_err rsu_prog_ready(struct m10bmc_sec *sec)
+{
+ unsigned long poll_timeout;
+ u32 doorbell, progress;
+ int ret;
+
+ ret = m10bmc_sys_read(sec->m10bmc, M10BMC_DOORBELL, &doorbell);
+ if (ret)
+ return FPGA_SEC_ERR_RW_ERROR;
+
+ poll_timeout = jiffies + msecs_to_jiffies(RSU_PREP_TIMEOUT_MS);
+ while (rsu_prog(doorbell) == RSU_PROG_PREPARE) {
+ msleep(RSU_PREP_INTERVAL_MS);
+ if (time_after(jiffies, poll_timeout))
+ break;
+
+ ret = m10bmc_sys_read(sec->m10bmc, M10BMC_DOORBELL, &doorbell);
+ if (ret)
+ return FPGA_SEC_ERR_RW_ERROR;
+ }
+
+ progress = rsu_prog(doorbell);
+ if (progress == RSU_PROG_PREPARE) {
+ log_error_regs(sec, doorbell);
+ return FPGA_SEC_ERR_TIMEOUT;
+ } else if (progress != RSU_PROG_READY) {
+ log_error_regs(sec, doorbell);
+ return FPGA_SEC_ERR_HW_ERROR;
+ }
+
+ return FPGA_SEC_ERR_NONE;
+}
+
+static enum fpga_sec_err rsu_send_data(struct m10bmc_sec *sec)
+{
+ u32 doorbell;
+ int ret;
+
+ ret = regmap_update_bits(sec->m10bmc->regmap,
+ M10BMC_SYS_BASE + M10BMC_DOORBELL,
+ DRBL_HOST_STATUS,
+ FIELD_PREP(DRBL_HOST_STATUS,
+ HOST_STATUS_WRITE_DONE));
+ if (ret)
+ return FPGA_SEC_ERR_RW_ERROR;
+
+ ret = regmap_read_poll_timeout(sec->m10bmc->regmap,
+ M10BMC_SYS_BASE + M10BMC_DOORBELL,
+ doorbell,
+ rsu_prog(doorbell) != RSU_PROG_READY,
+ NIOS_HANDSHAKE_INTERVAL_US,
+ NIOS_HANDSHAKE_TIMEOUT_US);
+
+ if (ret == -ETIMEDOUT) {
+ log_error_regs(sec, doorbell);
+ return FPGA_SEC_ERR_TIMEOUT;
+ } else if (ret) {
+ return FPGA_SEC_ERR_RW_ERROR;
+ }
+
+ switch (rsu_stat(doorbell)) {
+ case RSU_STAT_NORMAL:
+ case RSU_STAT_NIOS_OK:
+ case RSU_STAT_USER_OK:
+ case RSU_STAT_FACTORY_OK:
+ break;
+ default:
+ log_error_regs(sec, doorbell);
+ return FPGA_SEC_ERR_HW_ERROR;
+ }
+
+ return FPGA_SEC_ERR_NONE;
+}
+
+static int rsu_check_complete(struct m10bmc_sec *sec, u32 *doorbell)
+{
+ if (m10bmc_sys_read(sec->m10bmc, M10BMC_DOORBELL, doorbell))
+ return -EIO;
+
+ switch (rsu_stat(*doorbell)) {
+ case RSU_STAT_NORMAL:
+ case RSU_STAT_NIOS_OK:
+ case RSU_STAT_USER_OK:
+ case RSU_STAT_FACTORY_OK:
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ switch (rsu_prog(*doorbell)) {
+ case RSU_PROG_IDLE:
+ case RSU_PROG_RSU_DONE:
+ return 0;
+ case RSU_PROG_AUTHENTICATING:
+ case RSU_PROG_COPYING:
+ case RSU_PROG_UPDATE_CANCEL:
+ case RSU_PROG_PROGRAM_KEY_HASH:
+ return -EAGAIN;
+ default:
+ return -EINVAL;
+ }
+}
+
+static enum fpga_sec_err m10bmc_sec_prepare(struct fpga_sec_mgr *smgr)
+{
+ struct m10bmc_sec *sec = smgr->priv;
+ enum fpga_sec_err ret;
+
+ if (smgr->remaining_size > M10BMC_STAGING_SIZE)
+ return FPGA_SEC_ERR_INVALID_SIZE;
+
+ ret = rsu_check_idle(sec);
+ if (ret != FPGA_SEC_ERR_NONE)
+ return ret;
+
+ ret = rsu_update_init(sec);
+ if (ret != FPGA_SEC_ERR_NONE)
+ return ret;
+
+ return rsu_prog_ready(sec);
+}
+
+#define WRITE_BLOCK_SIZE 0x4000 /* Update remaining_size every 0x4000 bytes */
+
+static enum fpga_sec_err
+m10bmc_sec_write_blk(struct fpga_sec_mgr *smgr, u32 offset)
+{
+ struct m10bmc_sec *sec = smgr->priv;
+ unsigned int stride = regmap_get_reg_stride(sec->m10bmc->regmap);
+ u32 doorbell, blk_size;
+ int ret;
+
+ ret = m10bmc_sys_read(sec->m10bmc, M10BMC_DOORBELL, &doorbell);
+ if (ret) {
+ return FPGA_SEC_ERR_RW_ERROR;
+ } else if (rsu_prog(doorbell) != RSU_PROG_READY) {
+ log_error_regs(sec, doorbell);
+ return FPGA_SEC_ERR_HW_ERROR;
+ }
+
+ blk_size = min_t(u32, smgr->remaining_size, WRITE_BLOCK_SIZE);
+ ret = regmap_bulk_write(sec->m10bmc->regmap,
+ M10BMC_STAGING_BASE + offset,
+ (void *)smgr->data + offset,
+ (blk_size + stride - 1) / stride);
+
+ if (ret)
+ return FPGA_SEC_ERR_RW_ERROR;
+
+ smgr->remaining_size -= blk_size;
+ return FPGA_SEC_ERR_NONE;
+}
+
+/*
+ * m10bmc_sec_poll_complete() is called after handing things off to
+ * the BMC firmware. Depending on the type of update, it could be
+ * 30+ minutes before the BMC firmware completes the update. The
+ * smgr->driver_unload check allows the driver to be unloaded,
+ * but the BMC firmware will continue the update and no further
+ * secure updates can be started for this device until the update
+ * is complete.
+ */
+static enum fpga_sec_err m10bmc_sec_poll_complete(struct fpga_sec_mgr *smgr)
+{
+ struct m10bmc_sec *sec = smgr->priv;
+ unsigned long poll_timeout;
+ enum fpga_sec_err result;
+ u32 doorbell;
+ int ret;
+
+ result = rsu_send_data(sec);
+ if (result != FPGA_SEC_ERR_NONE)
+ return result;
+
+ poll_timeout = jiffies + msecs_to_jiffies(RSU_COMPLETE_TIMEOUT_MS);
+ do {
+ msleep(RSU_COMPLETE_INTERVAL_MS);
+ ret = rsu_check_complete(sec, &doorbell);
+ if (smgr->driver_unload)
+ return FPGA_SEC_ERR_CANCELED;
+ } while (ret == -EAGAIN && !time_after(jiffies, poll_timeout));
+
+ if (ret == -EAGAIN) {
+ log_error_regs(sec, doorbell);
+ return FPGA_SEC_ERR_TIMEOUT;
+ } else if (ret == -EIO) {
+ return FPGA_SEC_ERR_RW_ERROR;
+ } else if (ret) {
+ log_error_regs(sec, doorbell);
+ return FPGA_SEC_ERR_HW_ERROR;
+ }
+
+ return FPGA_SEC_ERR_NONE;
+}
+
+static enum fpga_sec_err m10bmc_sec_cancel(struct fpga_sec_mgr *smgr)
+{
+ struct m10bmc_sec *sec = smgr->priv;
+ u32 doorbell;
+ int ret;
+
+ ret = m10bmc_sys_read(sec->m10bmc, M10BMC_DOORBELL, &doorbell);
+ if (ret)
+ return FPGA_SEC_ERR_RW_ERROR;
+
+ if (rsu_prog(doorbell) != RSU_PROG_READY)
+ return FPGA_SEC_ERR_BUSY;
+
+ ret = regmap_update_bits(sec->m10bmc->regmap,
+ M10BMC_SYS_BASE + M10BMC_DOORBELL,
+ DRBL_HOST_STATUS,
+ FIELD_PREP(DRBL_HOST_STATUS,
+ HOST_STATUS_ABORT_RSU));
+
+ return ret ? FPGA_SEC_ERR_RW_ERROR : FPGA_SEC_ERR_NONE;
+}
+
+static const struct fpga_sec_mgr_ops m10bmc_sops = {
+ .prepare = m10bmc_sec_prepare,
+ .write_blk = m10bmc_sec_write_blk,
+ .poll_complete = m10bmc_sec_poll_complete,
+ .cancel = m10bmc_sec_cancel,
+};
static int m10bmc_secure_probe(struct platform_device *pdev)
{
Extend the MAX10 BMC Secure Update driver to include the functions that enable secure updates of BMC images, FPGA images, etc. Signed-off-by: Russ Weight <russell.h.weight@intel.com> --- v13: - No change v12: - Updated Date and KernelVersion fields in ABI documentation - Removed size parameter from the write_blk() op. m10bmc_sec_write_blk() no longer has a size parameter, and the block size is determined in this (the lower-level) driver. v11: - No change v10: - No change v9: - No change v8: - Previously patch 5/6, otherwise no change v7: - No change v6: - Changed (size / stride) calculation to ((size + stride - 1) / stride) to ensure that the proper count is passed to regmap_bulk_write(). - Removed unnecessary call to rsu_check_complete() in m10bmc_sec_poll_complete() and changed while loop to do/while loop. v5: - No change v4: - No change v3: - Changed: iops -> sops, imgr -> smgr, IFPGA_ -> FPGA_, ifpga_ to fpga_ - Changed "MAX10 BMC Secure Engine driver" to "MAX10 BMC Secure Update driver" - Removed wrapper functions (m10bmc_raw_*, m10bmc_sys_*). The underlying functions are now called directly. - Changed calling functions of functions that return "enum fpga_sec_err" to check for (ret != FPGA_SEC_ERR_NONE) instead of (ret) v2: - Reworked the rsu_start_done() function to make it more readable - Reworked while-loop condition/content in rsu_prog_ready() - Minor code cleanup per review comments - Added a comment to the m10bmc_sec_poll_complete() function to explain the context (could take 30+ minutes to complete). - Added m10bmc_ prefix to functions in m10bmc_iops structure - Moved MAX10 BMC address and function definitions to a separate patch. --- drivers/fpga/intel-m10-bmc-secure.c | 310 +++++++++++++++++++++++++++- 1 file changed, 309 insertions(+), 1 deletion(-)