@@ -199,6 +199,27 @@ &syscontroller {
status = "okay";
};
+&syscontroller_qspi {
+ /*
+ * The flash *is* there, but Icicle kits that have engineering sample
+ * silicon (write?) access to this flash to non-functional. The system
+ * controller itself can actually access it, but the MSS cannot write
+ * an image there. Instantiating a coreQSPI in the fabric & connecting
+ * it to the flash instead should work though. Pre-production or later
+ * silicon does not have this issue.
+ */
+ status = "disabled";
+
+ sys_ctrl_flash: flash@0 { // MT25QL01GBBB8ESF-0SIT
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <20000000>;
+ spi-rx-bus-width = <1>;
+ reg = <0>;
+ };
+};
+
&usb {
status = "okay";
dr_mode = "host";
@@ -173,11 +173,6 @@ refclk: mssrefclk {
#clock-cells = <0>;
};
- syscontroller: syscontroller {
- compatible = "microchip,mpfs-sys-controller";
- mboxes = <&mbox 0>;
- };
-
soc {
#address-cells = <2>;
#size-cells = <2>;
@@ -498,11 +493,28 @@ usb: usb@20201000 {
mbox: mailbox@37020000 {
compatible = "microchip,mpfs-mailbox";
- reg = <0x0 0x37020000 0x0 0x1000>, <0x0 0x2000318C 0x0 0x40>;
+ reg = <0x0 0x37020000 0x0 0x58>, <0x0 0x2000318C 0x0 0x40>,
+ <0x0 0x37020800 0x0 0x100>;
interrupt-parent = <&plic>;
interrupts = <96>;
#mbox-cells = <1>;
status = "disabled";
};
+
+ syscontroller_qspi: spi@37020100 {
+ compatible = "microchip,mpfs-qspi", "microchip,coreqspi-rtl-v2";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x37020100 0x0 0x100>;
+ interrupt-parent = <&plic>;
+ interrupts = <110>;
+ clocks = <&clkcfg CLK_QSPI>; /* this is probably wrong, consult the docs! */
+ status = "disabled";
+ };
+ };
+
+ syscontroller: syscontroller {
+ compatible = "microchip,mpfs-sys-controller";
+ mboxes = <&mbox 0>;
};
};
The system controller's flash can be accessed via an MSS-exposed QSPI controller sitting, which sits between the mailbox's control & data registers. On Icicle, it has an MT25QL01GBBB8ESF connected to it. The system controller and MSS both have separate QSPI controllers, both of which can access the flash, although the system controller takes priority. Unfortunately, on engineering sample silicon, such as that on Icicle kits, the MSS' QSPI controller cannot write to the flash due to a bug. As a workaround, a QSPI controller can be implemented in the FPGA fabric and the IO routing modified to connect it to the flash in place of the "hard" controller in the MSS. Signed-off-by: Conor Dooley <conor.dooley@microchip.com> --- .../boot/dts/microchip/mpfs-icicle-kit.dts | 21 ++++++++++++++++ arch/riscv/boot/dts/microchip/mpfs.dtsi | 24 ++++++++++++++----- 2 files changed, 39 insertions(+), 6 deletions(-)