@@ -1607,6 +1607,17 @@ config SENSORS_NZXT_SMART2
source "drivers/hwmon/occ/Kconfig"
+config SENSORS_OXP
+ tristate "OneXPlayer EC fan control"
+ depends on ACPI
+ depends on X86
+ help
+ If you say yes here you get support for fan readings and control over
+ OneXPlayer handheld devices. Only OneXPlayer mini AMD handheld variant
+ boards are supported.
+
+ Can also be built as a module. In that case it will be called oxp_sensors.
+
config SENSORS_PCF8591
tristate "Philips PCF8591 ADC/DAC"
depends on I2C
@@ -1957,7 +1968,7 @@ config SENSORS_ADS7871
config SENSORS_AMC6821
tristate "Texas Instruments AMC6821"
- depends on I2C
+ depends on I2C
help
If you say yes here you get support for the Texas Instruments
AMC6821 hardware monitoring chips.
@@ -167,6 +167,7 @@ obj-$(CONFIG_SENSORS_NSA320) += nsa320-hwmon.o
obj-$(CONFIG_SENSORS_NTC_THERMISTOR) += ntc_thermistor.o
obj-$(CONFIG_SENSORS_NZXT_KRAKEN2) += nzxt-kraken2.o
obj-$(CONFIG_SENSORS_NZXT_SMART2) += nzxt-smart2.o
+obj-$(CONFIG_SENSORS_OXP) += oxp-sensors.o
obj-$(CONFIG_SENSORS_PC87360) += pc87360.o
obj-$(CONFIG_SENSORS_PC87427) += pc87427.o
obj-$(CONFIG_SENSORS_PCF8591) += pcf8591.o
new file mode 100644
@@ -0,0 +1,278 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Platform driver for OXP Handhelds that expose fan reading and control
+ * via hwmon sysfs.
+ *
+ * All boards have the same DMI strings and they are told appart by the
+ * boot cpu vendor (Intel/AMD). Currently only AMD boards are supported
+ * but the code is made to be simple to add other handheld boards in the
+ * future.
+ * Fan control is provided via pwm interface in the range [0-255]. AMD
+ * boards use [0-100] as range in the EC, the written value is scaled to
+ * accommodate for that.
+ *
+ * PWM control is disabled by default, can be enabled via module parameter.
+ *
+ * Copyright (C) 2022 Joaquín I. Aramendía <samsagax@gmail.com>
+ */
+
+#include <linux/acpi.h>
+#include <linux/dev_printk.h>
+#include <linux/dmi.h>
+#include <linux/hwmon.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/processor.h>
+
+#define ACPI_LOCK_DELAY_MS 500
+
+/* Handle ACPI lock mechanism */
+struct lock_data {
+ u32 mutex;
+ bool (*lock)(struct lock_data *data);
+ bool (*unlock)(struct lock_data *data);
+};
+
+static bool lock_global_acpi_lock(struct lock_data *data)
+{
+ return ACPI_SUCCESS(acpi_acquire_global_lock(ACPI_LOCK_DELAY_MS,
+ &data->mutex));
+}
+
+static bool unlock_global_acpi_lock(struct lock_data *data)
+{
+ return ACPI_SUCCESS(acpi_release_global_lock(data->mutex));
+}
+
+#define OXP_SENSOR_FAN_REG 0x76 /* Fan reading is 2 registers long */
+#define OXP_SENSOR_PWM_REG 0x4B /* PWM reading is 1 register long */
+
+static const struct dmi_system_id dmi_table[] = {
+ {
+ .matches = {
+ DMI_EXACT_MATCH(DMI_BOARD_VENDOR,
+ "ONE-NETBOOK TECHNOLOGY CO., LTD."),
+ },
+ },
+ {
+ .matches = {
+ DMI_EXACT_MATCH(DMI_BOARD_VENDOR,
+ "ONE-NETBOOK"),
+ },
+ },
+ {},
+};
+
+struct oxp_status {
+ struct lock_data lock_data;
+};
+
+/* Helper functions to handle EC read/write */
+static int read_from_ec(u8 reg, int size, long *val)
+{
+ int i;
+ int ret;
+ u8 buffer;
+
+ *val = 0;
+ for (i = 0; i < size; i++) {
+ ret = ec_read(reg + i, &buffer);
+ if (ret)
+ return ret;
+ (*val) <<= i * 8;
+ *val += buffer;
+ }
+ return ret;
+}
+
+static int write_to_ec(const struct device *dev, u8 reg, u8 value)
+{
+ struct oxp_status *state = dev_get_drvdata(dev);
+ int ret;
+
+ if (!state->lock_data.lock(&state->lock_data)) {
+ dev_warn(dev, "Failed to acquire mutex");
+ return -EBUSY;
+ }
+
+ ret = ec_write(reg, value);
+
+ if (!state->lock_data.unlock(&state->lock_data))
+ dev_err(dev, "Failed to release mutex");
+
+ return ret;
+}
+
+static int oxp_pwm_enable(const struct device *dev)
+{
+ return write_to_ec(dev, OXP_SENSOR_PWM_REG, 0x01);
+}
+
+static int oxp_pwm_disable(const struct device *dev)
+{
+ return write_to_ec(dev, OXP_SENSOR_PWM_REG, 0x00);
+}
+
+/* Callbacks for hwmon interface */
+static umode_t oxp_ec_hwmon_is_visible(const void *drvdata,
+ enum hwmon_sensor_types type, u32 attr, int channel)
+{
+ switch (type) {
+ case hwmon_fan:
+ return 0444;
+ case hwmon_pwm:
+ return 0644;
+ default:
+ return 0;
+ }
+ return 0;
+}
+
+static int oxp_platform_read(struct device *dev, enum hwmon_sensor_types type,
+ u32 attr, int channel, long *val)
+{
+ int ret;
+
+ switch (type) {
+ case hwmon_fan:
+ switch (attr) {
+ case hwmon_fan_input:
+ return read_from_ec(OXP_SENSOR_FAN_REG,
+ 2,
+ val);
+ default:
+ dev_dbg(dev, "Unknown attribute for type %d: %d\n", type, attr);
+ return -EOPNOTSUPP;
+ }
+ case hwmon_pwm:
+ switch (attr) {
+ case hwmon_pwm_input:
+ ret = read_from_ec(OXP_SENSOR_PWM_REG,
+ 2, val);
+ *val = (*val * 255) / 100;
+ return ret;
+ case hwmon_pwm_enable:
+ return read_from_ec(OXP_SENSOR_PWM_REG, 1, val);
+ default:
+ dev_dbg(dev, "Unknown attribute for type %d: %d\n", type, attr);
+ return -EOPNOTSUPP;
+ }
+ default:
+ dev_dbg(dev, "Unknown sensor type %d.\n", type);
+ return -EOPNOTSUPP;
+ }
+}
+
+static int oxp_platform_write(struct device *dev, enum hwmon_sensor_types type,
+ u32 attr, int channel, long val)
+{
+ switch (type) {
+ case hwmon_pwm:
+ switch (attr) {
+ case hwmon_pwm_enable:
+ if (val == 1)
+ return oxp_pwm_enable(dev);
+ else if (val == 0)
+ return oxp_pwm_disable(dev);
+ else
+ return -EINVAL;
+ case hwmon_pwm_input:
+ if (val < 0 || val > 255)
+ return -EINVAL;
+ val = (val * 100) / 255;
+ return write_to_ec(dev, OXP_SENSOR_PWM_REG, val);
+ default:
+ dev_dbg(dev, "Unknown attribute for type %d: %d", type, attr);
+ return -EOPNOTSUPP;
+ }
+ default:
+ dev_dbg(dev, "Unknown sensor type: %d", type);
+ return -EOPNOTSUPP;
+ }
+ return -EINVAL;
+}
+
+/* Known sensors in the OXP EC controllers */
+static const struct hwmon_channel_info *oxp_platform_sensors[] = {
+ HWMON_CHANNEL_INFO(fan,
+ HWMON_F_INPUT | HWMON_F_MAX | HWMON_F_MIN),
+ HWMON_CHANNEL_INFO(pwm,
+ HWMON_PWM_INPUT | HWMON_PWM_ENABLE),
+ NULL,
+};
+
+static const struct hwmon_ops oxp_ec_hwmon_ops = {
+ .is_visible = oxp_ec_hwmon_is_visible,
+ .read = oxp_platform_read,
+ .write = oxp_platform_write,
+};
+
+static const struct hwmon_chip_info oxp_ec_chip_info = {
+ .ops = &oxp_ec_hwmon_ops,
+ .info = oxp_platform_sensors,
+};
+
+/* Initialization logic */
+static int oxp_platform_probe(struct platform_device *pdev)
+{
+ const struct dmi_system_id *dmi_entry;
+ struct device *dev = &pdev->dev;
+ struct device *hwdev;
+ struct oxp_status *state;
+
+ /* Have to check for AMD processor here */
+ dmi_entry = dmi_first_match(dmi_table);
+ if (!dmi_entry || boot_cpu_data.x86_vendor != X86_VENDOR_AMD)
+ return -ENODEV;
+
+ state = devm_kzalloc(dev, sizeof(struct oxp_status), GFP_KERNEL);
+ if (!state)
+ return -ENOMEM;
+
+ state->lock_data.mutex = 0;
+ state->lock_data.lock = lock_global_acpi_lock;
+ state->lock_data.unlock = unlock_global_acpi_lock;
+
+ hwdev = devm_hwmon_device_register_with_info(dev, "oxpec", state,
+ &oxp_ec_chip_info, NULL);
+
+ return PTR_ERR_OR_ZERO(hwdev);
+}
+
+static struct platform_driver oxp_platform_driver = {
+ .driver = {
+ .name = "oxp-platform",
+ },
+ .probe = oxp_platform_probe,
+};
+
+static struct platform_device *oxp_platform_device;
+
+static int __init oxp_platform_init(void)
+{
+ oxp_platform_device =
+ platform_create_bundle(&oxp_platform_driver,
+ oxp_platform_probe, NULL, 0, NULL, 0);
+
+ if (IS_ERR(oxp_platform_device))
+ return PTR_ERR(oxp_platform_device);
+
+ return 0;
+}
+
+static void __exit oxp_platform_exit(void)
+{
+ platform_device_unregister(oxp_platform_device);
+ platform_driver_unregister(&oxp_platform_driver);
+}
+
+MODULE_DEVICE_TABLE(dmi, dmi_table);
+module_init(oxp_platform_init);
+module_exit(oxp_platform_exit);
+
+MODULE_AUTHOR("Joaquín Ignacio Aramendía <samsagax@gmail.com>");
+MODULE_DESCRIPTION(
+ "Platform driver that handles ACPI EC of OneXPlayer devices");
+MODULE_LICENSE("GPL");
Sensors driver for OXP Handhelds from One-Netbook that expose fan reading and control via hwmon sysfs. As far as I could gather all OXP boards have the same DMI strings and they are told appart by the boot cpu vendor (Intel/AMD). Currently only AMD boards are supported. Fan control is provided via pwm interface in the range [0-255]. AMD boards have [0-100] as range in the EC, the written value is scaled to accommodate for that. Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com> --- Rewritten the driver according to feedback, checkpatch passes, removed unnecessary complexity and moved the driver to hwmon --- drivers/hwmon/Kconfig | 13 +- drivers/hwmon/Makefile | 1 + drivers/hwmon/oxp-sensors.c | 278 ++++++++++++++++++++++++++++++++++++ 3 files changed, 291 insertions(+), 1 deletion(-) create mode 100644 drivers/hwmon/oxp-sensors.c -- 2.38.1