@@ -1,32 +1,38 @@
What: /sys/class/hwmon/hwmonX/name
Description:
- The chip name.
+ Chip name.
+
+ Represents the chip name. It is the only mandatory attribute.
+
This should be a short, lowercase string, not containing
whitespace, dashes, or the wildcard character '*'.
- This attribute represents the chip name. It is the only
- mandatory attribute.
+
I2C devices get this attribute created automatically.
RO
What: /sys/class/hwmon/hwmonX/label
Description:
- A descriptive label that allows to uniquely identify a
+ Chip label.
+
+ A descriptive freeform label that uniquely identifies a
device within the system.
- The contents of the label are free-form.
RO
What: /sys/class/hwmon/hwmonX/update_interval
Description:
- The interval at which the chip will update readings.
- Unit: millisecond
+ Chip reading update interval.
- RW
+ The interval at which the chip will update readings.
Some devices have a variable update rate or interval.
This attribute can be used to change it to the desired value.
+ Unit: millisecond
+
+ RW
+
What: /sys/class/hwmon/hwmonX/inY_min
Description:
Voltage min value.
@@ -39,14 +45,14 @@ What: /sys/class/hwmon/hwmonX/inY_lcrit
Description:
Voltage critical min value.
+ If voltage drops to or below this limit, the system may
+ take drastic action such as powering down or restarting.
+ At the very least, it should report a fault.
+
Unit: millivolt
RW
- If voltage drops to or below this limit, the system may
- take drastic action such as power down or reset. At the very
- least, it should report a fault.
-
What: /sys/class/hwmon/hwmonX/inY_max
Description:
Voltage max value.
@@ -59,39 +65,40 @@ What: /sys/class/hwmon/hwmonX/inY_crit
Description:
Voltage critical max value.
+ If voltage reaches or exceeds this limit, the system may
+ take drastic action such as powering down or restarting.
+ At the very least, it should report a fault.
+
Unit: millivolt
RW
- If voltage reaches or exceeds this limit, the system may
- take drastic action such as power down or reset. At the very
- least, it should report a fault.
-
What: /sys/class/hwmon/hwmonX/inY_input
Description:
Voltage input value.
- Unit: millivolt
-
- RO
+ The voltage measured on the chip pin. The actual voltage
+ depends on the scaling resistors on the motherboard, as
+ recommended in the chip datasheet.
- Voltage measured on the chip pin.
+ This varies by chip and by motherboard. Because of this
+ variation, values are generally NOT scaled by the chip driver,
+ and scaling must be done by the application.
- Actual voltage depends on the scaling resistors on the
- motherboard, as recommended in the chip datasheet.
+ However, some drivers (notably ``lm87`` and ``via686a``) do
+ scale, because of internal resistors built into the chip.
+ These drivers will output the actual voltage.
- This varies by chip and by motherboard.
- Because of this variation, values are generally NOT scaled
- by the chip driver, and must be done by the application.
- However, some drivers (notably lm87 and via686a)
- do scale, because of internal resistors built into a chip.
- These drivers will output the actual voltage. Rule of
- thumb: drivers should report the voltage values at the
+ Rule of thumb: Drivers should report the voltage values at the
"pins" of the chip.
+ Unit: millivolt
+
+ RO
+
What: /sys/class/hwmon/hwmonX/inY_average
Description:
- Average voltage
+ Average voltage.
Unit: millivolt
@@ -99,7 +106,7 @@ Description:
What: /sys/class/hwmon/hwmonX/inY_lowest
Description:
- Historical minimum voltage
+ Historical minimum voltage.
Unit: millivolt
@@ -107,7 +114,7 @@ Description:
What: /sys/class/hwmon/hwmonX/inY_highest
Description:
- Historical maximum voltage
+ Historical maximum voltage.
Unit: millivolt
@@ -115,13 +122,13 @@ Description:
What: /sys/class/hwmon/hwmonX/inY_reset_history
Description:
- Reset inX_lowest and inX_highest
+ Reset ``inY_lowest`` and ``inY_highest``.
WO
What: /sys/class/hwmon/hwmonX/in_reset_history
Description:
- Reset inX_lowest and inX_highest for all sensors
+ Reset ``inY_lowest`` and ``inY_highest`` for all sensors.
WO
@@ -129,23 +136,22 @@ What: /sys/class/hwmon/hwmonX/inY_label
Description:
Suggested voltage channel label.
- Text string
+ A text string.
- Should only be created if the driver has hints about what
- this voltage channel is being used for, and user-space
- doesn't. In all other cases, the label is provided by
- user-space.
+ Should only be created if the driver has hints about what this
+ voltage channel is being used for, and userspace doesn't.
+ In all other cases, the label is provided by userspace.
RO
What: /sys/class/hwmon/hwmonX/inY_enable
Description:
- Enable or disable the sensors.
+ Enable or disable the sensor.
- When disabled the sensor read will return -ENODATA.
+ When disabled, reading the sensor returns ``-ENODATA``.
- - 1: Enable
- 0: Disable
+ - 1: Enable
RW
@@ -153,18 +159,16 @@ What: /sys/class/hwmon/hwmonX/cpuY_vid
Description:
CPU core reference voltage.
+ Not always correct.
+
Unit: millivolt
RO
- Not always correct.
-
What: /sys/class/hwmon/hwmonX/vrm
Description:
Voltage Regulator Module version number.
- RW (but changing it should no more be necessary)
-
Originally the VRM standard version multiplied by 10, but now
an arbitrary number, as not all standards have a version
number.
@@ -172,6 +176,8 @@ Description:
Affects the way the driver calculates the CPU core reference
voltage from the vid pins.
+ RW (but changing it should not be necessary)
+
What: /sys/class/hwmon/hwmonX/inY_rated_min
Description:
Minimum rated voltage.
@@ -190,7 +196,7 @@ Description:
What: /sys/class/hwmon/hwmonX/fanY_min
Description:
- Fan minimum value
+ Fan minimum value.
Unit: revolution/min (RPM)
@@ -198,11 +204,12 @@ Description:
What: /sys/class/hwmon/hwmonX/fanY_max
Description:
- Fan maximum value
+ Fan maximum value.
+
+ Only rarely supported by the hardware.
Unit: revolution/min (RPM)
- Only rarely supported by the hardware.
RW
What: /sys/class/hwmon/hwmonX/fanY_input
@@ -217,21 +224,19 @@ What: /sys/class/hwmon/hwmonX/fanY_div
Description:
Fan divisor.
- Integer value in powers of two (1, 2, 4, 8, 16, 32, 64, 128).
-
- RW
-
+ An integer power of two (1, 2, 4, 8, 16, 32, 64, 128).
Some chips only support values 1, 2, 4 and 8.
+
Note that this is actually an internal clock divisor, which
affects the measurable speed range, not the read value.
+ RW
+
What: /sys/class/hwmon/hwmonX/fanY_pulses
Description:
Number of tachometer pulses per fan revolution.
- Integer value, typically between 1 and 4.
-
- RW
+ An integer value, typically between 1 and 4.
This value is a characteristic of the fan connected to the
device's input, so it has to be set in accordance with the fan
@@ -242,74 +247,80 @@ Description:
thus attribute) the value assumed by all devices is 2 pulses
per fan revolution.
+ RW
+
What: /sys/class/hwmon/hwmonX/fanY_target
Description:
- Desired fan speed
+ Desired fan speed.
+
+ Only makes sense if the chip supports closed-loop fan speed
+ control based on the measured fan speed.
Unit: revolution/min (RPM)
RW
- Only makes sense if the chip supports closed-loop fan speed
- control based on the measured fan speed.
-
What: /sys/class/hwmon/hwmonX/fanY_label
Description:
Suggested fan channel label.
- Text string
+ A text string.
- Should only be created if the driver has hints about what
- this fan channel is being used for, and user-space doesn't.
- In all other cases, the label is provided by user-space.
+ Should only be created if the driver has hints about what this
+ fan channel is being used for, and userspace doesn't.
+ In all other cases, the label is provided by userspace.
RO
What: /sys/class/hwmon/hwmonX/fanY_enable
Description:
- Enable or disable the sensors.
+ Enable or disable the sensor.
- When disabled the sensor read will return -ENODATA.
+ When disabled, reading the sensor returns ``-ENODATA``.
- - 1: Enable
- 0: Disable
+ - 1: Enable
RW
What: /sys/class/hwmon/hwmonX/fanY_fault
Description:
- Reports if a fan has reported failure.
+ Fan channel fault indicator.
+
+ Indicates whether a fan has reported failure.
+ - 0: OK
- 1: Failed
- - 0: Ok
RO
What: /sys/class/hwmon/hwmonX/pwmY
Description:
- Pulse width modulation fan control.
+ Pulse-width modulation fan control.
- Integer value in the range 0 to 255
+ An integer value in the range 0 to 255.
- RW
+ 255 represents 100%.
- 255 is max or 100%.
+ RW
What: /sys/class/hwmon/hwmonX/pwmY_enable
Description:
- Fan speed control method:
-
- - 0: no fan speed control (i.e. fan at full speed)
- - 1: manual fan speed control enabled (using `pwmY`)
- - 2+: automatic fan speed control enabled
+ Fan speed control method.
Check individual chip documentation files for automatic mode
details.
+ - 0: No fan speed control (i.e. fan at full speed)
+ - 1: Manual fan speed control enabled (using ``pwmY``)
+ - 2+: Automatic fan speed control enabled
+
RW
What: /sys/class/hwmon/hwmonX/pwmY_mode
Description:
+ Fan speed control mode.
+
- 0: DC mode (direct current)
- 1: PWM mode (pulse-width modulation)
@@ -319,18 +330,24 @@ What: /sys/class/hwmon/hwmonX/pwmY_freq
Description:
Base PWM frequency in Hz.
- Only possibly available when pwmN_mode is PWM, but not always
- present even then.
+ May only be available when ``pwmY_mode`` is PWM,
+ but not always present even then.
RW
What: /sys/class/hwmon/hwmonX/pwmY_auto_channels_temp
Description:
- Select which temperature channels affect this PWM output in
- auto mode.
+ Auto mode channel mask.
+
+ Select which temperature channels affect this PWM output
+ in auto mode.
- Bitfield, 1 is temp1, 2 is temp2, 4 is temp3 etc...
- Which values are possible depend on the chip used.
+ A bitfield. Possible values are chip-dependent. For example:
+
+ - 1: ``temp1``
+ - 2: ``temp2``
+ - 4: ``temp3``
+ - 5: ``temp1`` and ``temp3``
RW
@@ -338,10 +355,13 @@ What: /sys/class/hwmon/hwmonX/pwmY_auto_pointZ_pwm
What: /sys/class/hwmon/hwmonX/pwmY_auto_pointZ_temp
What: /sys/class/hwmon/hwmonX/pwmY_auto_pointZ_temp_hyst
Description:
- Define the PWM vs temperature curve.
+ PWM temperature curve definition.
+
+ Define the PWM vs. temperature curve.
+ The number of trip points is chip-dependent.
- Number of trip points is chip-dependent. Use this for chips
- which associate trip points to PWM output channels.
+ Use this for chips that associate trip points
+ with PWM output channels.
RW
@@ -349,10 +369,13 @@ What: /sys/class/hwmon/hwmonX/tempY_auto_pointZ_pwm
What: /sys/class/hwmon/hwmonX/tempY_auto_pointZ_temp
What: /sys/class/hwmon/hwmonX/tempY_auto_pointZ_temp_hyst
Description:
- Define the PWM vs temperature curve.
+ PWM temperature curve definition.
- Number of trip points is chip-dependent. Use this for chips
- which associate trip points to temperature channels.
+ Define the PWM vs. temperature curve.
+ The number of trip points is chip-dependent.
+
+ Use this for chips that associate trip points
+ with temperature channels.
RW
@@ -360,24 +383,25 @@ What: /sys/class/hwmon/hwmonX/tempY_type
Description:
Sensor type selection.
- Integers 1 to 6
-
- RW
+ Not all types are supported by all chips.
- 1: CPU embedded diode
- 2: 3904 transistor
- - 3: thermal diode
- - 4: thermistor
+ - 3: Thermal diode
+ - 4: Thermistor
- 5: AMD AMDSI
- 6: Intel PECI
- Not all types are supported by all chips
+ RW
What: /sys/class/hwmon/hwmonX/tempY_max
Description:
Temperature max value.
- Unit: millidegree Celsius (or millivolt, see below)
+ In some cases, this is a voltage. Please see
+ Documentation/hwmon/sysfs-interface.rst for more details.
+
+ Unit: millidegree Celsius (or millivolt)
RW
@@ -385,7 +409,10 @@ What: /sys/class/hwmon/hwmonX/tempY_min
Description:
Temperature min value.
- Unit: millidegree Celsius
+ In some cases, this is a voltage. Please see
+ Documentation/hwmon/sysfs-interface.rst for more details.
+
+ Unit: millidegree Celsius (or millivolt)
RW
@@ -393,20 +420,27 @@ What: /sys/class/hwmon/hwmonX/tempY_max_hyst
Description:
Temperature hysteresis value for max limit.
- Unit: millidegree Celsius
+ Must be reported as an absolute temperature,
+ NOT as a delta from the max value.
- Must be reported as an absolute temperature, NOT a delta
- from the max value.
+ In some cases, this is a voltage. Please see
+ Documentation/hwmon/sysfs-interface.rst for more details.
+
+ Unit: millidegree Celsius (or millivolt)
RW
What: /sys/class/hwmon/hwmonX/tempY_min_hyst
Description:
Temperature hysteresis value for min limit.
- Unit: millidegree Celsius
- Must be reported as an absolute temperature, NOT a delta
- from the min value.
+ Must be reported as an absolute temperature,
+ NOT as a delta from the min value.
+
+ In some cases, this is a voltage. Please see
+ Documentation/hwmon/sysfs-interface.rst for more details.
+
+ Unit: millidegree Celsius (or millivolt)
RW
@@ -414,51 +448,67 @@ What: /sys/class/hwmon/hwmonX/tempY_input
Description:
Temperature input value.
- Unit: millidegree Celsius
+ In some cases, this is a voltage. Please see
+ Documentation/hwmon/sysfs-interface.rst for more details.
+
+ Unit: millidegree Celsius (or millivolt)
RO
What: /sys/class/hwmon/hwmonX/tempY_crit
Description:
- Temperature critical max value, typically greater than
- corresponding temp_max values.
+ Temperature critical max value.
+
+ Typically greater than corresponding ``tempY_max`` values.
+
+ In some cases, this is a voltage. Please see
+ Documentation/hwmon/sysfs-interface.rst for more details.
- Unit: millidegree Celsius
+ Unit: millidegree Celsius (or millivolt)
RW
What: /sys/class/hwmon/hwmonX/tempY_crit_alarm
Description:
- Critical high temperature alarm flag.
-
- - 0: OK
- - 1: temperature has reached tempY_crit
-
- RW
+ Temperature critical max alarm indicator.
Contrary to regular alarm flags which clear themselves
automatically when read, this one sticks until cleared by
the user. This is done by writing 0 to the file. Writing
other values is unsupported.
+ - 0: No alarm
+ - 1: Alarm
+
+ RW
+
What: /sys/class/hwmon/hwmonX/tempY_crit_hyst
Description:
Temperature hysteresis value for critical limit.
- Unit: millidegree Celsius
+ Must be reported as an absolute temperature,
+ NOT as a delta from the critical value.
+
+ In some cases, this is a voltage. Please see
+ Documentation/hwmon/sysfs-interface.rst for more details.
- Must be reported as an absolute temperature, NOT a delta
- from the critical value.
+ Unit: millidegree Celsius (or millivolt)
RW
What: /sys/class/hwmon/hwmonX/tempY_emergency
Description:
- Temperature emergency max value, for chips supporting more than
- two upper temperature limits. Must be equal or greater than
- corresponding temp_crit values.
+ Temperature emergency max value.
- Unit: millidegree Celsius
+ For chips supporting more than two upper temperature limits.
+
+ Must be equal to or greater than corresponding ``tempY_crit``
+ values.
+
+ In some cases, this is a voltage. Please see
+ Documentation/hwmon/sysfs-interface.rst for more details.
+
+ Unit: millidegree Celsius (or millivolt)
RW
@@ -466,19 +516,26 @@ What: /sys/class/hwmon/hwmonX/tempY_emergency_hyst
Description:
Temperature hysteresis value for emergency limit.
- Unit: millidegree Celsius
+ Must be reported as an absolute temperature,
+ NOT as a delta from the emergency value.
+
+ In some cases, this is a voltage. Please see
+ Documentation/hwmon/sysfs-interface.rst for more details.
- Must be reported as an absolute temperature, NOT a delta
- from the emergency value.
+ Unit: millidegree Celsius (or millivolt)
RW
What: /sys/class/hwmon/hwmonX/tempY_lcrit
Description:
- Temperature critical min value, typically lower than
- corresponding temp_min values.
+ Temperature critical min value.
- Unit: millidegree Celsius
+ Typically lower than corresponding ``tempY_min`` values.
+
+ In some cases, this is a voltage. Please see
+ Documentation/hwmon/sysfs-interface.rst for more details.
+
+ Unit: millidegree Celsius (or millivolt)
RW
@@ -486,68 +543,80 @@ What: /sys/class/hwmon/hwmonX/tempY_lcrit_hyst
Description:
Temperature hysteresis value for critical min limit.
- Unit: millidegree Celsius
+ Must be reported as an absolute temperature,
+ NOT as a delta from the critical min value.
+
+ In some cases, this is a voltage. Please see
+ Documentation/hwmon/sysfs-interface.rst for more details.
- Must be reported as an absolute temperature, NOT a delta
- from the critical min value.
+ Unit: millidegree Celsius (or millivolt)
RW
What: /sys/class/hwmon/hwmonX/tempY_offset
Description:
- Temperature offset which is added to the temperature reading
- by the chip.
+ Temperature offset.
- Unit: millidegree Celsius
+ An offset added to the temperature reading by the chip.
- Read/Write value.
+ In some cases, this is a voltage. Please see
+ Documentation/hwmon/sysfs-interface.rst for more details.
+
+ Unit: millidegree Celsius (or millivolt)
+
+ RW
What: /sys/class/hwmon/hwmonX/tempY_label
Description:
Suggested temperature channel label.
- Text string
+ A text string.
- Should only be created if the driver has hints about what
- this temperature channel is being used for, and user-space
- doesn't. In all other cases, the label is provided by
- user-space.
+ Should only be created if the driver has hints about what this
+ temperature channel is being used for, and userspace doesn't.
+ In all other cases, the label is provided by userspace.
RO
What: /sys/class/hwmon/hwmonX/tempY_lowest
Description:
- Historical minimum temperature
+ Historical minimum temperature.
+
+ In some cases, this is a voltage. Please see
+ Documentation/hwmon/sysfs-interface.rst for more details.
- Unit: millidegree Celsius
+ Unit: millidegree Celsius (or millivolt)
RO
What: /sys/class/hwmon/hwmonX/tempY_highest
Description:
- Historical maximum temperature
+ Historical maximum temperature.
- Unit: millidegree Celsius
+ In some cases, this is a voltage. Please see
+ Documentation/hwmon/sysfs-interface.rst for more details.
+
+ Unit: millidegree Celsius (or millivolt)
RO
What: /sys/class/hwmon/hwmonX/tempY_reset_history
Description:
- Reset temp_lowest and temp_highest
+ Reset ``tempY_lowest`` and ``tempY_highest``.
WO
What: /sys/class/hwmon/hwmonX/temp_reset_history
Description:
- Reset temp_lowest and temp_highest for all sensors
+ Reset ``tempY_lowest`` and ``tempY_highest`` for all sensors.
WO
What: /sys/class/hwmon/hwmonX/tempY_enable
Description:
- Enable or disable the sensors.
+ Enable or disable the sensor.
- When disabled the sensor read will return -ENODATA.
+ When disabled, reading the sensor returns ``-ENODATA``.
- 1: Enable
- 0: Disable
@@ -558,7 +627,10 @@ What: /sys/class/hwmon/hwmonX/tempY_rated_min
Description:
Minimum rated temperature.
- Unit: millidegree Celsius
+ In some cases, this is a voltage. Please see
+ Documentation/hwmon/sysfs-interface.rst for more details.
+
+ Unit: millidegree Celsius (or millivolt)
RO
@@ -566,13 +638,16 @@ What: /sys/class/hwmon/hwmonX/tempY_rated_max
Description:
Maximum rated temperature.
- Unit: millidegree Celsius
+ In some cases, this is a voltage. Please see
+ Documentation/hwmon/sysfs-interface.rst for more details.
+
+ Unit: millidegree Celsius (or millivolt)
RO
What: /sys/class/hwmon/hwmonX/currY_max
Description:
- Current max value
+ Current max value.
Unit: milliampere
@@ -588,7 +663,7 @@ Description:
What: /sys/class/hwmon/hwmonX/currY_lcrit
Description:
- Current critical low value
+ Current critical min value.
Unit: milliampere
@@ -596,7 +671,7 @@ Description:
What: /sys/class/hwmon/hwmonX/currY_crit
Description:
- Current critical high value.
+ Current critical max value.
Unit: milliampere
@@ -604,7 +679,7 @@ Description:
What: /sys/class/hwmon/hwmonX/currY_input
Description:
- Current input value
+ Current input value.
Unit: milliampere
@@ -612,7 +687,7 @@ Description:
What: /sys/class/hwmon/hwmonX/currY_average
Description:
- Average current use
+ Average current use.
Unit: milliampere
@@ -620,7 +695,7 @@ Description:
What: /sys/class/hwmon/hwmonX/currY_lowest
Description:
- Historical minimum current
+ Historical minimum current.
Unit: milliampere
@@ -628,27 +703,29 @@ Description:
What: /sys/class/hwmon/hwmonX/currY_highest
Description:
- Historical maximum current
+ Historical maximum current.
+
Unit: milliampere
+
RO
What: /sys/class/hwmon/hwmonX/currY_reset_history
Description:
- Reset currX_lowest and currX_highest
+ Reset ``currY_lowest`` and ``currY_highest``.
WO
What: /sys/class/hwmon/hwmonX/curr_reset_history
Description:
- Reset currX_lowest and currX_highest for all sensors
+ Reset ``currY_lowest`` and ``currY_highest`` for all sensors.
WO
What: /sys/class/hwmon/hwmonX/currY_enable
Description:
- Enable or disable the sensors.
+ Enable or disable the sensor.
- When disabled the sensor read will return -ENODATA.
+ When disabled, reading the sensor returns ``-ENODATA``.
- 1: Enable
- 0: Disable
@@ -673,102 +750,105 @@ Description:
What: /sys/class/hwmon/hwmonX/powerY_average
Description:
- Average power use
+ Average power use.
- Unit: microWatt
+ Unit: microwatt
RO
What: /sys/class/hwmon/hwmonX/powerY_average_interval
Description:
- Power use averaging interval. A poll
- notification is sent to this file if the
- hardware changes the averaging interval.
+ Power use averaging interval.
+
+ A poll notification is sent to this file if
+ the hardware changes the averaging interval.
- Unit: milliseconds
+ Unit: millisecond
RW
What: /sys/class/hwmon/hwmonX/powerY_average_interval_max
Description:
- Maximum power use averaging interval
+ Maximum power use averaging interval.
- Unit: milliseconds
+ Unit: millisecond
RO
What: /sys/class/hwmon/hwmonX/powerY_average_interval_min
Description:
- Minimum power use averaging interval
+ Minimum power use averaging interval.
- Unit: milliseconds
+ Unit: millisecond
RO
What: /sys/class/hwmon/hwmonX/powerY_average_highest
Description:
- Historical average maximum power use
+ Historical average maximum power use.
- Unit: microWatt
+ Unit: microwatt
RO
What: /sys/class/hwmon/hwmonX/powerY_average_lowest
Description:
- Historical average minimum power use
+ Historical average minimum power use.
- Unit: microWatt
+ Unit: microwatt
RO
What: /sys/class/hwmon/hwmonX/powerY_average_max
Description:
- A poll notification is sent to
- `powerY_average` when power use
- rises above this value.
+ Maximum average power notification threshold.
+
+ A poll notification is sent to `powerY_average`
+ when power use rises above this value.
- Unit: microWatt
+ Unit: microwatt
RW
What: /sys/class/hwmon/hwmonX/powerY_average_min
Description:
- A poll notification is sent to
- `powerY_average` when power use
- sinks below this value.
+ Minimum average power notification threshold.
- Unit: microWatt
+ A poll notification is sent to `powerY_average`
+ when power use sinks below this value.
+
+ Unit: microwatt
RW
What: /sys/class/hwmon/hwmonX/powerY_input
Description:
- Instantaneous power use
+ Instantaneous power use.
- Unit: microWatt
+ Unit: microwatt
RO
What: /sys/class/hwmon/hwmonX/powerY_input_highest
Description:
- Historical maximum power use
+ Historical maximum power use.
- Unit: microWatt
+ Unit: microwatt
RO
What: /sys/class/hwmon/hwmonX/powerY_input_lowest
Description:
- Historical minimum power use
+ Historical minimum power use.
- Unit: microWatt
+ Unit: microwatt
RO
What: /sys/class/hwmon/hwmonX/powerY_reset_history
Description:
- Reset input_highest, input_lowest,
- average_highest and average_lowest.
+ Reset ``powerY_input_highest``, ``powerY_input_lowest``,
+ ``powerY_average_highest``, and ``powerY_average_lowest``.
WO
@@ -776,29 +856,34 @@ What: /sys/class/hwmon/hwmonX/powerY_accuracy
Description:
Accuracy of the power meter.
- Unit: Percent
+ Unit: percent
RO
What: /sys/class/hwmon/hwmonX/powerY_cap
Description:
- If power use rises above this limit, the
- system should take action to reduce power use.
- A poll notification is sent to this file if the
- cap is changed by the hardware. The `*_cap`
- files only appear if the cap is known to be
- enforced by hardware.
+ Power reduction threshold.
+
+ If power use rises above this limit, the system should
+ take action to reduce power use.
- Unit: microWatt
+ A poll notification is sent to this file if the cap is
+ changed by the hardware.
+
+ The `powerY_cap` files only appear if the cap is known
+ to be enforced by hardware.
+
+ Unit: microwatt
RW
What: /sys/class/hwmon/hwmonX/powerY_cap_hyst
Description:
- Margin of hysteresis built around capping and
- notification.
+ Threshold hysteresis margin.
- Unit: microWatt
+ Margin of hysteresis built around capping and notification.
+
+ Unit: microwatt
RW
@@ -806,7 +891,7 @@ What: /sys/class/hwmon/hwmonX/powerY_cap_max
Description:
Maximum cap that can be set.
- Unit: microWatt
+ Unit: microwatt
RO
@@ -814,7 +899,7 @@ What: /sys/class/hwmon/hwmonX/powerY_cap_min
Description:
Minimum cap that can be set.
- Unit: microWatt
+ Unit: microwatt
RO
@@ -822,29 +907,27 @@ What: /sys/class/hwmon/hwmonX/powerY_max
Description:
Maximum power.
- Unit: microWatt
+ Unit: microwatt
RW
What: /sys/class/hwmon/hwmonX/powerY_crit
Description:
- Critical maximum power.
+ Critical power reduction threshold.
- If power rises to or above this limit, the
- system is expected take drastic action to reduce
- power consumption, such as a system shutdown or
- a forced powerdown of some devices.
+ If power rises to or above this limit, the system is expected
+ to take drastic action to reduce power consumption, such as a
+ system shutdown or a forced powerdown of some devices.
- Unit: microWatt
+ Unit: microwatt
RW
What: /sys/class/hwmon/hwmonX/powerY_enable
Description:
- Enable or disable the sensors.
+ Enable or disable the sensor.
- When disabled the sensor read will return
- -ENODATA.
+ When disabled, reading the sensor returns ``-ENODATA``.
- 1: Enable
- 0: Disable
@@ -855,7 +938,7 @@ What: /sys/class/hwmon/hwmonX/powerY_rated_min
Description:
Minimum rated power.
- Unit: microWatt
+ Unit: microwatt
RO
@@ -863,24 +946,23 @@ What: /sys/class/hwmon/hwmonX/powerY_rated_max
Description:
Maximum rated power.
- Unit: microWatt
+ Unit: microwatt
RO
What: /sys/class/hwmon/hwmonX/energyY_input
Description:
- Cumulative energy use
+ Cumulative energy use.
- Unit: microJoule
+ Unit: microjoule
RO
What: /sys/class/hwmon/hwmonX/energyY_enable
Description:
- Enable or disable the sensors.
+ Enable or disable the sensor.
- When disabled the sensor read will return
- -ENODATA.
+ When disabled, reading the sensor returns ``-ENODATA``.
- 1: Enable
- 0: Disable
@@ -889,19 +971,17 @@ Description:
What: /sys/class/hwmon/hwmonX/humidityY_input
Description:
- Humidity
+ Humidity.
- Unit: milli-percent (per cent mille, pcm)
+ Unit: millipercent (per cent mille, pcm)
RO
-
What: /sys/class/hwmon/hwmonX/humidityY_enable
Description:
- Enable or disable the sensors
+ Enable or disable the sensor.
- When disabled the sensor read will return
- -ENODATA.
+ When disabled, reading the sensor returns ``-ENODATA``.
- 1: Enable
- 0: Disable
@@ -912,7 +992,7 @@ What: /sys/class/hwmon/hwmonX/humidityY_rated_min
Description:
Minimum rated humidity.
- Unit: milli-percent (per cent mille, pcm)
+ Unit: millipercent (per cent mille, pcm)
RO
@@ -920,39 +1000,40 @@ What: /sys/class/hwmon/hwmonX/humidityY_rated_max
Description:
Maximum rated humidity.
- Unit: milli-percent (per cent mille, pcm)
+ Unit: millipercent (per cent mille, pcm)
RO
-
What: /sys/class/hwmon/hwmonX/intrusionY_alarm
Description:
- Chassis intrusion detection
-
- - 0: OK
- - 1: intrusion detected
-
- RW
+ Chassis intrusion indicator.
Contrary to regular alarm flags which clear themselves
automatically when read, this one sticks until cleared by
the user. This is done by writing 0 to the file. Writing
other values is unsupported.
+ - 0: OK
+ - 1: Intrusion detected
+
+ RW
+
What: /sys/class/hwmon/hwmonX/intrusionY_beep
Description:
- Chassis intrusion beep
+ Chassis intrusion beep.
- - 0: disable
- - 1: enable
+ - 0: Disable
+ - 1: Enable
RW
What: /sys/class/hwmon/hwmonX/device/pec
Description:
- PEC support on I2C devices
+ PEC support on I2C devices.
- - 0, off, n: disable
- - 1, on, y: enable
+ - 0: Off
+ - 1: On
+ - n: Disable
+ - y: Enable
RW
Reformat attribute descriptions to impose a consistent style and improve rendering in the generated docs. For example, some multi-line descriptions were being rendered as a single line/paragraph due to missing blank line separators. Harmonize short descriptions with those in the sysfs interface spec and move in the longer explanations that were shortened there. Add cross-references (just file paths) in descriptions of temperature attributes back to the sysfs interface spec whence they were moved to explain why some sensor chips report temperature as a voltage. Previously there was only a note in the existing description of tempY_max directing the reader to "see below" as though the move had never occurred. Fix minor issues (typos, grammar, etc.) and add just a touch of markup (inline literals only). Link: https://lore.kernel.org/all/5f47619ed882b0b8d1c84b56f7ea17bac0854b77.1632994837.git.mchehab+huawei@kernel.org/ Signed-off-by: James Seo <james@equiv.tech> --- Documentation/ABI/testing/sysfs-class-hwmon | 563 +++++++++++--------- 1 file changed, 322 insertions(+), 241 deletions(-)