new file mode 100644
@@ -0,0 +1,159 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/hwmon/adi,ltc4282.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices LTC4282 I2C High Current Hot Swap Controller over I2C
+
+maintainers:
+ - Nuno Sa <nuno.sa@analog.com>
+
+description: |
+ Analog Devices LTC4282 I2C High Current Hot Swap Controller over I2C.
+
+ https://www.analog.com/media/en/technical-documentation/data-sheets/ltc4282.pdf
+
+properties:
+ compatible:
+ enum:
+ - adi,ltc4282
+
+ reg:
+ maxItems: 1
+
+ vdd-supply: true
+
+ clocks:
+ maxItems: 1
+
+ '#clock-cells':
+ const: 0
+
+ adi,rsense-nano-ohms:
+ description: Value of the sense resistor.
+
+ adi,vin-mode-microvolt:
+ description:
+ Selects operating range for the Undervoltage, Overvoltage and Foldback
+ pins. Also for the ADC. Should be set to the nominal input voltage.
+ enum: [3300000, 5000000, 12000000, 24000000]
+ default: 12000000
+
+ adi,fet-bad-timeout-ms:
+ description:
+ From the moment a FET bad conditions is present, this property selects the
+ wait time/timeout for a FET-bad fault to be signaled. Setting this to 0,
+ disables FET bad faults to be reported.
+ default: 255
+ maximum: 255
+
+ adi,overvoltage-dividers:
+ description: |
+ Select which dividers to use for VDD Overvoltage detection. Note that
+ when the internal dividers are used the threshold is referenced to VDD.
+ The percentages in the datasheet are misleading since the actual values
+ to look for are in the "Absolute Maximum Ratings" table in the
+ "Comparator Inputs" section. In there there's a line for each of the 5%,
+ 10% and 15% settings with the actual min, typical and max tolerances.
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [external, vdd_5_percent, vdd_10_percent, vdd_15_percent]
+ default: external
+
+ adi,undervoltage-dividers:
+ description: |
+ Select which dividers to use for VDD Overvoltage detection. Note that
+ when the internal dividers are used the threshold is referenced to VDD.
+ The percentages in the datasheet are misleading since the actual values
+ to look for are in the "Absolute Maximum Ratings" table in the
+ "Comparator Inputs" section. In there there's a line for each of the 5%,
+ 10% and 15% settings with the actual min, typical and max tolerances.
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [external, vdd_5_percent, vdd_10_percent, vdd_15_percent]
+ default: external
+
+ adi,current-limit-sense-microvolt:
+ description:
+ The current limit sense voltage of the chip is adjustable between
+ 12.5mV and 34.4mV in 3.1mV steps. This effectively limits the current
+ on the load.
+ enum: [12500, 15625, 18750, 21875, 25000, 28125, 31250, 34375]
+ default: 25000
+
+ adi,overcurrent-retry:
+ description:
+ If set, enables the chip to auto-retry 256 timer cycles after an
+ Overcurrent fault.
+ type: boolean
+
+ adi,overvoltage-retry-disable:
+ description:
+ If set, disables the chip to auto-retry 50ms after an Overvoltage fault.
+ It's enabled by default.
+ type: boolean
+
+ adi,undervoltage-retry-disable:
+ description:
+ If set, disables the chip to auto-retry 50ms after an Undervoltage fault.
+ It's enabled by default.
+ type: boolean
+
+ adi,fault-log-enable:
+ description:
+ If set, enables the FAULT_LOG and ADC_ALERT_LOG registers to be written
+ to the EEPROM when a fault bit transitions high and hence, will be
+ available after a power cycle (the chip loads the contents of
+ the EE_FAULT_LOG register - the one in EEPROM - into FAULT_LOG at boot).
+ type: boolean
+
+ adi,gpio1-mode:
+ description: Defines the function of the Pin. It can indicate that power is
+ good (PULL the pin low when power is not good) or that power is bad (Go
+ into high-z when power is not good).
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [power_bad, power_good]
+ default: power_good
+
+ adi,gpio2-mode:
+ description: Defines the function of the Pin. It can be set as the input for
+ the ADC or indicating that the MOSFET is in stress (dissipating power).
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [adc_input, stress_fet]
+ default: adc_input
+
+ adi,gpio3-monitor-enable:
+ description: If set, gpio3 is set as input for the ADC instead of gpio2.
+ type: boolean
+
+allOf:
+ - if:
+ required:
+ - adi,gpio3-monitor-enable
+ then:
+ properties:
+ adi,gpio2-mode:
+ const: stress_fet
+
+required:
+ - compatible
+ - reg
+ - adi,rsense-nano-ohms
+
+additionalProperties: false
+
+examples:
+ - |
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hwmon@50 {
+ compatible = "adi,ltc4282";
+ reg = <0x50>;
+ adi,rsense-nano-ohms = <500>;
+
+ adi,gpio1-mode = "power_good";
+ adi,gpio2-mode = "adc_input";
+ };
+ };
+...
@@ -12592,6 +12592,12 @@ S: Maintained
F: Documentation/hwmon/ltc4261.rst
F: drivers/hwmon/ltc4261.c
+LTC4282 HARDWARE MONITOR DRIVER
+M: Nuno Sa <nuno.sa@analog.com>
+L: linux-hwmon@vger.kernel.org
+S: Supported
+F: Documentation/devicetree/bindings/hwmon/adi,ltc4282.yaml
+
LTC4286 HARDWARE MONITOR DRIVER
M: Delphine CC Chiu <Delphine_CC_Chiu@Wiwynn.com>
L: linux-i2c@vger.kernel.org
Add bindings for the LTC4282 High Current Hot Swap Controller with I2C Compatible Monitoring. Signed-off-by: Nuno Sa <nuno.sa@analog.com> --- .../devicetree/bindings/hwmon/adi,ltc4282.yaml | 159 +++++++++++++++++++++ MAINTAINERS | 6 + 2 files changed, 165 insertions(+)