@@ -67,9 +67,7 @@
#define INA226_READ_AVG(reg) FIELD_GET(INA226_AVG_RD_MASK, reg)
-#define INA226_ALERT_POLARITY_MASK BIT(1)
-#define INA226_ALERT_POL_LOW 0
-#define INA226_ALERT_POL_HIGH 1
+#define INA226_ALERT_POLARITY BIT(1)
/* bit number of alert functions in Mask/Enable Register */
#define INA226_SHUNT_OVER_VOLTAGE_MASK BIT(15)
@@ -141,6 +139,7 @@ struct ina2xx_config {
struct ina2xx_data {
const struct ina2xx_config *config;
+ enum ina2xx_ids chip;
long rshunt;
long current_lsb_uA;
@@ -211,39 +210,6 @@ static u16 ina226_interval_to_reg(unsigned long interval)
return FIELD_PREP(INA226_AVG_RD_MASK, avg_bits);
}
-static int ina2xx_set_alert_polarity(struct ina2xx_data *data,
- unsigned long val)
-{
- return regmap_update_bits(data->regmap, INA226_MASK_ENABLE,
- INA226_ALERT_POLARITY_MASK,
- FIELD_PREP(INA226_ALERT_POLARITY_MASK, val));
-}
-
-/*
- * Calibration register is set to the best value, which eliminates
- * truncation errors on calculating current register in hardware.
- * According to datasheet (eq. 3) the best values are 2048 for
- * ina226 and 4096 for ina219. They are hardcoded as calibration_value.
- */
-static int ina2xx_calibrate(struct ina2xx_data *data)
-{
- return regmap_write(data->regmap, INA2XX_CALIBRATION,
- data->config->calibration_value);
-}
-
-/*
- * Initialize the configuration and calibration registers.
- */
-static int ina2xx_init(struct ina2xx_data *data)
-{
- int ret = regmap_write(data->regmap, INA2XX_CONFIG,
- data->config->config_default);
- if (ret < 0)
- return ret;
-
- return ina2xx_calibrate(data);
-}
-
static int ina2xx_read_reg(struct device *dev, int reg, unsigned int *regval)
{
struct ina2xx_data *data = dev_get_drvdata(dev);
@@ -651,12 +617,48 @@ static const struct attribute_group ina226_group = {
.attrs = ina226_attrs,
};
+/*
+ * Initialize chip
+ */
+static int ina2xx_init(struct device *dev, struct ina2xx_data *data)
+{
+ struct regmap *regmap = data->regmap;
+ u32 shunt;
+ int ret;
+
+ if (device_property_read_u32(dev, "shunt-resistor", &shunt) < 0)
+ shunt = INA2XX_RSHUNT_DEFAULT;
+
+ ret = ina2xx_set_shunt(data, shunt);
+ if (ret < 0)
+ return ret;
+
+ ret = regmap_write(regmap, INA2XX_CONFIG, data->config->config_default);
+ if (ret < 0)
+ return ret;
+
+ if (data->chip == ina226) {
+ bool active_high = device_property_read_bool(dev, "ti,alert-polarity-active-high");
+
+ regmap_update_bits(regmap, INA226_MASK_ENABLE, INA226_ALERT_POLARITY,
+ FIELD_PREP(INA226_ALERT_POLARITY, active_high));
+ }
+
+ /*
+ * Calibration register is set to the best value, which eliminates
+ * truncation errors on calculating current register in hardware.
+ * According to datasheet (eq. 3) the best values are 2048 for
+ * ina226 and 4096 for ina219. They are hardcoded as calibration_value.
+ */
+ return regmap_write(regmap, INA2XX_CALIBRATION,
+ data->config->calibration_value);
+}
+
static int ina2xx_probe(struct i2c_client *client)
{
struct device *dev = &client->dev;
struct ina2xx_data *data;
struct device *hwmon_dev;
- u32 val;
int ret, group = 0;
enum ina2xx_ids chip;
@@ -668,15 +670,9 @@ static int ina2xx_probe(struct i2c_client *client)
/* set the device type */
data->config = &ina2xx_config[chip];
+ data->chip = chip;
mutex_init(&data->config_lock);
- if (device_property_read_u32(dev, "shunt-resistor", &val) < 0)
- val = INA2XX_RSHUNT_DEFAULT;
-
- ret = ina2xx_set_shunt(data, val);
- if (ret < 0)
- return dev_err_probe(dev, ret, "Invalid shunt resistor value\n");
-
data->regmap = devm_regmap_init_i2c(client, &ina2xx_regmap_config);
if (IS_ERR(data->regmap)) {
dev_err(dev, "failed to allocate register map\n");
@@ -687,30 +683,9 @@ static int ina2xx_probe(struct i2c_client *client)
if (ret)
return dev_err_probe(dev, ret, "failed to enable vs regulator\n");
- if (chip == ina226) {
- if (device_property_read_bool(dev, "ti,alert-polarity-active-high")) {
- ret = ina2xx_set_alert_polarity(data,
- INA226_ALERT_POL_HIGH);
- if (ret < 0) {
- return dev_err_probe(dev, ret,
- "failed to set alert polarity active high\n");
- }
- } else {
- /* Set default value i.e active low */
- ret = ina2xx_set_alert_polarity(data,
- INA226_ALERT_POL_LOW);
- if (ret < 0) {
- return dev_err_probe(dev, ret,
- "failed to set alert polarity active low\n");
- }
- }
- }
-
- ret = ina2xx_init(data);
- if (ret < 0) {
- dev_err(dev, "error configuring the device: %d\n", ret);
- return -ENODEV;
- }
+ ret = ina2xx_init(dev, data);
+ if (ret < 0)
+ return dev_err_probe(dev, ret, "failed to configure device\n");
data->groups[group++] = &ina2xx_group;
if (chip == ina226)
Move all chip initialization code into a single function. No functional change. Signed-off-by: Guenter Roeck <linux@roeck-us.net> --- v2: Fixed setting alert polarity drivers/hwmon/ina2xx.c | 111 ++++++++++++++++------------------------- 1 file changed, 43 insertions(+), 68 deletions(-)