@@ -4672,6 +4672,10 @@
Format: { parport<nr> | timid | 0 }
See also Documentation/admin-guide/parport.rst.
+ pmbus.wp= [HW] PMBus Chips write protection forced mode
+ Format: { 0 | 1 }
+ See drivers/hwmon/pmbus/pmbus_core.c
+
pmtmr= [X86] Manual setup of pmtmr I/O Port.
Override pmtimer IOPort with a hex value.
e.g. pmtmr=0x508
@@ -31,6 +31,20 @@
#define PMBUS_ATTR_ALLOC_SIZE 32
#define PMBUS_NAME_SIZE 24
+/*
+ * PMBus write protect forced mode:
+ * PMBus may come up with a variety of write protection configuration.
+ * 'pmbus_wp' may be used if a particular write protection is necessary.
+ * The ability to actually alter the protection may also depend on the chip
+ * so the actual runtime write protection configuration may differ from
+ * the requested one. pmbus_core currently support the following value:
+ * - 0: write protection removed
+ * - 1: write protection fully enabled, including OPERATION and VOUT_COMMAND
+ * registers. Chips essentially become read-only with this.
+ */
+static int wp = -1;
+module_param(wp, int, 0444);
+
struct pmbus_sensor {
struct pmbus_sensor *next;
char name[PMBUS_NAME_SIZE]; /* sysfs sensor name */
@@ -2658,6 +2672,45 @@ static void pmbus_remove_pec(void *dev)
device_remove_file(dev, &dev_attr_pec);
}
+static void pmbus_init_wp(struct i2c_client *client, struct pmbus_data *data)
+{
+ int ret;
+
+ switch (wp) {
+ case 0:
+ _pmbus_write_byte_data(client, 0xff,
+ PMBUS_WRITE_PROTECT, 0);
+ break;
+
+ case 1:
+ _pmbus_write_byte_data(client, 0xff,
+ PMBUS_WRITE_PROTECT, PB_WP_ALL);
+ break;
+
+ default:
+ /* Ignore the other values */
+ break;
+ }
+
+ ret = _pmbus_read_byte_data(client, 0xff, PMBUS_WRITE_PROTECT);
+
+ switch (ret) {
+ case PB_WP_ALL:
+ data->flags |= PMBUS_OP_PROTECTED;
+ fallthrough;
+ case PB_WP_OP:
+ data->flags |= PMBUS_VOUT_PROTECTED;
+ fallthrough;
+ case PB_WP_VOUT:
+ data->flags |= PMBUS_WRITE_PROTECTED | PMBUS_SKIP_STATUS_CHECK;
+ break;
+
+ default:
+ /* Ignore manufacturer specific and invalid as well as errors */
+ break;
+ }
+}
+
static int pmbus_init_common(struct i2c_client *client, struct pmbus_data *data,
struct pmbus_driver_info *info)
{
@@ -2711,25 +2764,8 @@ static int pmbus_init_common(struct i2c_client *client, struct pmbus_data *data,
* faults, and we should not try it. Also, in that case, writes into
* limit registers need to be disabled.
*/
- if (!(data->flags & PMBUS_NO_WRITE_PROTECT)) {
- ret = _pmbus_read_byte_data(client, 0xff, PMBUS_WRITE_PROTECT);
-
- switch (ret) {
- case PB_WP_ALL:
- data->flags |= PMBUS_OP_PROTECTED;
- fallthrough;
- case PB_WP_OP:
- data->flags |= PMBUS_VOUT_PROTECTED;
- fallthrough;
- case PB_WP_VOUT:
- data->flags |= PMBUS_WRITE_PROTECTED | PMBUS_SKIP_STATUS_CHECK;
- break;
-
- default:
- /* Ignore manufacturer specific and invalid as well as errors */
- break;
- }
- }
+ if (!(data->flags & PMBUS_NO_WRITE_PROTECT))
+ pmbus_init_wp(client, data);
if (data->info->pages)
pmbus_clear_faults(client);
Add a module parameter to force the write protection mode of pmbus chips. 2 protections modes are provided to start with: * 0: Remove the write protection if possible * 1: Enable full write protection if possible Of course, if the parameter is not provided, the default write protection status of the pmbus chips is left untouched. Suggested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> --- Documentation/admin-guide/kernel-parameters.txt | 4 ++ drivers/hwmon/pmbus/pmbus_core.c | 74 ++++++++++++++++++------- 2 files changed, 59 insertions(+), 19 deletions(-)