@@ -224,9 +224,9 @@ config SENSORS_LTC2978_REGULATOR
depends on SENSORS_LTC2978 && REGULATOR
help
If you say yes here you get regulator support for Linear Technology
- LTC3880, LTC3883, LTC3884, LTC3886, LTC3887, LTC3889, LTC7880,
- LTM4644, LTM4675, LTM4676, LTM4677, LTM4678, LTM4680, LTM4686,
- and LTM4700.
+ LTC3880, LTC3883, LTC3884, LTC3886, LTC3887, LTC3889, LTC7841,
+ LTC7880, LTM4644, LTM4675, LTM4676, LTM4677, LTM4678, LTM4680,
+ LTM4686, and LTM4700.
config SENSORS_LTC3815
tristate "Linear Technologies LTC3815"
@@ -23,7 +23,8 @@ enum chips {
/* Managers */
ltc2972, ltc2974, ltc2975, ltc2977, ltc2978, ltc2979, ltc2980,
/* Controllers */
- ltc3880, ltc3882, ltc3883, ltc3884, ltc3886, ltc3887, ltc3889, ltc7132, ltc7880,
+ ltc3880, ltc3882, ltc3883, ltc3884, ltc3886, ltc3887, ltc3889, ltc7132,
+ ltc7841, ltc7880,
/* Modules */
ltm2987, ltm4664, ltm4675, ltm4676, ltm4677, ltm4678, ltm4680, ltm4686,
ltm4700,
@@ -50,7 +51,7 @@ enum chips {
#define LTC3880_MFR_CLEAR_PEAKS 0xe3
#define LTC3880_MFR_TEMPERATURE2_PEAK 0xf4
-/* LTC3883, LTC3884, LTC3886, LTC3889, LTC7132, LTC7880 */
+/* LTC3883, LTC3884, LTC3886, LTC3889, LTC7132, LTC7841 and LTC7880 only */
#define LTC3883_MFR_IIN_PEAK 0xe1
/* LTC2975 only */
@@ -80,6 +81,7 @@ enum chips {
#define LTC3887_ID 0x4700
#define LTC3889_ID 0x4900
#define LTC7132_ID 0x4CE0
+#define LTC7841_ID 0x40D0
#define LTC7880_ID 0x49E0
#define LTM2987_ID_A 0x8010 /* A/B for two die IDs */
#define LTM2987_ID_B 0x8020
@@ -548,6 +550,7 @@ static const struct i2c_device_id ltc2978_id[] = {
{"ltc3887", ltc3887},
{"ltc3889", ltc3889},
{"ltc7132", ltc7132},
+ {"ltc7841", ltc7841},
{"ltc7880", ltc7880},
{"ltm2987", ltm2987},
{"ltm4664", ltm4664},
@@ -654,6 +657,8 @@ static int ltc2978_get_id(struct i2c_client *client)
return ltc3889;
else if (chip_id == LTC7132_ID)
return ltc7132;
+ else if (chip_id == LTC7841_ID)
+ return ltc7841;
else if (chip_id == LTC7880_ID)
return ltc7880;
else if (chip_id == LTM2987_ID_A || chip_id == LTM2987_ID_B)
@@ -854,6 +859,16 @@ static int ltc2978_probe(struct i2c_client *client)
| PMBUS_HAVE_POUT
| PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP;
break;
+ case ltc7841:
+ data->features |= FEAT_CLEAR_PEAKS;
+ info->read_word_data = ltc3883_read_word_data;
+ info->pages = LTC3883_NUM_PAGES;
+ info->func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_IIN
+ | PMBUS_HAVE_STATUS_INPUT
+ | PMBUS_HAVE_VOUT | PMBUS_HAVE_STATUS_VOUT
+ | PMBUS_HAVE_IOUT
+ | PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP;
+ break;
default:
return -ENODEV;
}
@@ -907,6 +922,7 @@ static const struct of_device_id ltc2978_of_match[] = {
{ .compatible = "lltc,ltc3887" },
{ .compatible = "lltc,ltc3889" },
{ .compatible = "lltc,ltc7132" },
+ { .compatible = "lltc,ltc7841" },
{ .compatible = "lltc,ltc7880" },
{ .compatible = "lltc,ltm2987" },
{ .compatible = "lltc,ltm4664" },
Add support for LTC7841. The LTC7841 is a high performance PolyPhase® single output synchronous boost converter controller. Multiphase operation reduces input and output capacitor requirements and allows the use of smaller inductors than the single-phase equivalent. The relevant registers in the LTC7841 are similar to the LTC7880, only reduced by some amount. So it's just a matter of adding the chip id. The device also doesn't support polling, on top of the reduced register set, so a separate case for setting the chip info is added. Signed-off-by: Mariel Tinaco <Mariel.Tinaco@analog.com> --- drivers/hwmon/pmbus/Kconfig | 6 +++--- drivers/hwmon/pmbus/ltc2978.c | 20 ++++++++++++++++++-- 2 files changed, 21 insertions(+), 5 deletions(-)