@@ -3211,6 +3211,81 @@ struct ec_response_battery_vendor_param {
} __ec_align4;
/*****************************************************************************/
+/*
+ * HDMI CEC commands
+ *
+ * These commands are for sending and receiving message via HDMI CEC
+ */
+
+#define MAX_CEC_MSG_LEN 16
+
+/* CEC message from the AP to be written on the CEC bus */
+#define EC_CMD_CEC_WRITE_MSG 0x00B8
+
+/**
+ * struct ec_params_cec_write - Message to write to the CEC bus
+ * @msg: message content to write to the CEC bus
+ */
+struct ec_params_cec_write {
+ uint8_t msg[MAX_CEC_MSG_LEN];
+} __ec_align1;
+
+/* Set various CEC parameters */
+#define EC_CMD_CEC_SET 0x00BA
+
+/**
+ * struct ec_params_cec_set - CEC parameters set
+ * @cmd: parameter type, can be CEC_CMD_ENABLE or CEC_CMD_LOGICAL_ADDRESS
+ * @val: in case cmd is CEC_CMD_ENABLE, this field can be 0 to disable CEC
+ * or 1 to enable CEC functionality, in case cmd is
+ * CEC_CMD_LOGICAL_ADDRESS, this field encodes the requested logical
+ * address between 0 and 15 or 0xff to unregister
+ */
+struct ec_params_cec_set {
+ uint8_t cmd; /* enum cec_command */
+ uint8_t val;
+} __ec_align1;
+
+/* Read various CEC parameters */
+#define EC_CMD_CEC_GET 0x00BB
+
+/**
+ * struct ec_params_cec_get - CEC parameters get
+ * @cmd: parameter type, can be CEC_CMD_ENABLE or CEC_CMD_LOGICAL_ADDRESS
+ */
+struct ec_params_cec_get {
+ uint8_t cmd; /* enum cec_command */
+} __ec_align1;
+
+/**
+ * struct ec_response_cec_get - CEC parameters get response
+ * @val: in case cmd was CEC_CMD_ENABLE, this field will 0 if CEC is
+ * disabled or 1 if CEC functionality is enabled,
+ * in case cmd was CEC_CMD_LOGICAL_ADDRESS, this will encode the
+ * configured logical address between 0 and 15 or 0xff if unregistered
+ */
+struct ec_response_cec_get {
+ uint8_t val;
+} __ec_align1;
+
+/* CEC parameters command */
+enum cec_command {
+ /* CEC reading, writing and events enable */
+ CEC_CMD_ENABLE,
+ /* CEC logical address */
+ CEC_CMD_LOGICAL_ADDRESS,
+};
+
+/* Events from CEC to AP */
+enum mkbp_cec_event {
+ /* Outgoing message was acknowledged by a follower */
+ EC_MKBP_CEC_SEND_OK = BIT(0),
+ /* Outgoing message was not acknowledged */
+ EC_MKBP_CEC_SEND_FAILED = BIT(1),
+};
+
+/*****************************************************************************/
+
/* Commands for I2S recording on audio codec. */
#define EC_CMD_CODEC_I2S 0x00BC
@@ -3339,79 +3414,6 @@ struct ec_params_reboot_ec {
*/
#define EC_CMD_GET_PANIC_INFO 0x00D3
-/*****************************************************************************/
-/*
- * HDMI CEC commands
- *
- * These commands are for sending and receiving message via HDMI CEC
- */
-#define EC_MAX_CEC_MSG_LEN 16
-
-/* CEC message from the AP to be written on the CEC bus */
-#define EC_CMD_CEC_WRITE_MSG 0x00B8
-
-/**
- * struct ec_params_cec_write - Message to write to the CEC bus
- * @msg: message content to write to the CEC bus
- */
-struct ec_params_cec_write {
- uint8_t msg[EC_MAX_CEC_MSG_LEN];
-} __ec_align1;
-
-/* Set various CEC parameters */
-#define EC_CMD_CEC_SET 0x00BA
-
-/**
- * struct ec_params_cec_set - CEC parameters set
- * @cmd: parameter type, can be CEC_CMD_ENABLE or CEC_CMD_LOGICAL_ADDRESS
- * @val: in case cmd is CEC_CMD_ENABLE, this field can be 0 to disable CEC
- * or 1 to enable CEC functionality, in case cmd is CEC_CMD_LOGICAL_ADDRESS,
- * this field encodes the requested logical address between 0 and 15
- * or 0xff to unregister
- */
-struct ec_params_cec_set {
- uint8_t cmd; /* enum cec_command */
- uint8_t val;
-} __ec_align1;
-
-/* Read various CEC parameters */
-#define EC_CMD_CEC_GET 0x00BB
-
-/**
- * struct ec_params_cec_get - CEC parameters get
- * @cmd: parameter type, can be CEC_CMD_ENABLE or CEC_CMD_LOGICAL_ADDRESS
- */
-struct ec_params_cec_get {
- uint8_t cmd; /* enum cec_command */
-} __ec_align1;
-
-/**
- * struct ec_response_cec_get - CEC parameters get response
- * @val: in case cmd was CEC_CMD_ENABLE, this field will 0 if CEC is
- * disabled or 1 if CEC functionality is enabled,
- * in case cmd was CEC_CMD_LOGICAL_ADDRESS, this will encode the
- * configured logical address between 0 and 15 or 0xff if unregistered
- */
-struct ec_response_cec_get {
- uint8_t val;
-} __ec_align1;
-
-/* CEC parameters command */
-enum ec_cec_command {
- /* CEC reading, writing and events enable */
- CEC_CMD_ENABLE,
- /* CEC logical address */
- CEC_CMD_LOGICAL_ADDRESS,
-};
-
-/* Events from CEC to AP */
-enum mkbp_cec_event {
- /* Outgoing message was acknowledged by a follower */
- EC_MKBP_CEC_SEND_OK = BIT(0),
- /* Outgoing message was not acknowledged */
- EC_MKBP_CEC_SEND_FAILED = BIT(1),
-};
-
/*****************************************************************************/
/*
* Special commands