diff --git a/MAINTAINERS b/MAINTAINERS
index 43604d6ab96c..a2fee2f03530 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1978,6 +1978,7 @@ F:	drivers/dma/ste_dma40*
 F:	drivers/hwspinlock/u8500_hsem.c
 F:	drivers/i2c/busses/i2c-nomadik.c
 F:	drivers/i2c/busses/i2c-stu300.c
+F:	drivers/iio/adc/ab8500-gpadc.c
 F:	drivers/mfd/ab3100*
 F:	drivers/mfd/ab8500*
 F:	drivers/mfd/abx500*
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 7e3286265a38..fba7ddcdd8e2 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -6,6 +6,16 @@
 
 menu "Analog to digital converters"
 
+config AB8500_GPADC
+	bool "ST-Ericsson AB8500 GPADC driver"
+	depends on AB8500_CORE && REGULATOR_AB8500
+	default y
+	help
+	  AB8500 Analog Baseband, mixed signal integrated circuit GPADC
+	  (General Purpose Analog to Digital Converter) driver used to monitor
+	  internal voltages, convert accessory and battery, AC (charger, mains)
+	  and USB voltages integral to the U8500 platform.
+
 config AD_SIGMA_DELTA
 	tristate
 	select IIO_BUFFER
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index ef9cc485fb67..fc1b6ebb0cde 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -4,6 +4,7 @@
 #
 
 # When adding new entries keep the list in alphabetical order
+obj-$(CONFIG_AB8500_GPADC) += ab8500-gpadc.o
 obj-$(CONFIG_AD_SIGMA_DELTA) += ad_sigma_delta.o
 obj-$(CONFIG_AD7124) += ad7124.o
 obj-$(CONFIG_AD7266) += ad7266.o
diff --git a/drivers/iio/adc/ab8500-gpadc.c b/drivers/iio/adc/ab8500-gpadc.c
new file mode 100644
index 000000000000..fd5b18d7f0c2
--- /dev/null
+++ b/drivers/iio/adc/ab8500-gpadc.c
@@ -0,0 +1,1218 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * Author: Arun R Murthy <arun.murthy@stericsson.com>
+ * Author: Daniel Willerud <daniel.willerud@stericsson.com>
+ * Author: Johan Palsson <johan.palsson@stericsson.com>
+ * Author: M'boumba Cedric Madianga
+ * Author: Linus Walleij <linus.walleij@linaro.org>
+ *
+ * AB8500 General Purpose ADC driver. The AB8500 uses reference voltages:
+ * VinVADC, and VADC relative to GND to do its job. It monitors main and backup
+ * battery voltages, AC (mains) voltage, USB cable voltage, as well as voltages
+ * representing the temperature of the chip die and battery, accessory
+ * detection by resistance measurements using relative voltages and GSM burst
+ * information.
+ *
+ * Some of the voltages are measured on external pins on the IC, such as
+ * battery temperature or "ADC aux" 1 and 2. Other voltages are internal rails
+ * from other parts of the ASIC such as main charger voltage, main and battery
+ * backup voltage or USB VBUS voltage. For this reason drivers for other
+ * parts of the system are required to obtain handles to the ADC to do work
+ * for them and the IIO driver provides arbitration among these consumers.
+ */
+#include <linux/init.h>
+#include <linux/bits.h>
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/spinlock.h>
+#include <linux/delay.h>
+#include <linux/pm_runtime.h>
+#include <linux/platform_device.h>
+#include <linux/completion.h>
+#include <linux/regulator/consumer.h>
+#include <linux/random.h>
+#include <linux/err.h>
+#include <linux/slab.h>
+#include <linux/mfd/abx500.h>
+#include <linux/mfd/abx500/ab8500.h>
+
+/* GPADC register offsets and bit definitions */
+
+#define AB8500_GPADC_CTRL1_REG		0x00
+/* GPADC control register 1 bits */
+#define AB8500_GPADC_CTRL1_DISABLE		0x00
+#define AB8500_GPADC_CTRL1_ENABLE		BIT(0)
+#define AB8500_GPADC_CTRL1_TRIG_ENA		BIT(1)
+#define AB8500_GPADC_CTRL1_START_SW_CONV	BIT(2)
+#define AB8500_GPADC_CTRL1_BTEMP_PULL_UP	BIT(3)
+/* 0 = use rising edge, 1 = use falling edge */
+#define AB8500_GPADC_CTRL1_TRIG_EDGE		BIT(4)
+/* 0 = use VTVOUT, 1 = use VRTC as pull-up supply for battery temp NTC */
+#define AB8500_GPADC_CTRL1_PUPSUPSEL		BIT(5)
+#define AB8500_GPADC_CTRL1_BUF_ENA		BIT(6)
+#define AB8500_GPADC_CTRL1_ICHAR_ENA		BIT(7)
+
+#define AB8500_GPADC_CTRL2_REG		0x01
+#define AB8500_GPADC_CTRL3_REG		0x02
+/*
+ * GPADC control register 2 and 3 bits
+ * the bit layout is the same for SW and HW conversion set-up
+ */
+#define AB8500_GPADC_CTRL2_AVG_1		0x00
+#define AB8500_GPADC_CTRL2_AVG_4		BIT(5)
+#define AB8500_GPADC_CTRL2_AVG_8		BIT(6)
+#define AB8500_GPADC_CTRL2_AVG_16		(BIT(5) | BIT(6))
+
+enum ab8500_gpadc_channel {
+	AB8500_GPADC_CHAN_UNUSED = 0x00,
+	AB8500_GPADC_CHAN_BAT_CTRL = 0x01,
+	AB8500_GPADC_CHAN_BAT_TEMP = 0x02,
+	/* This is not used on AB8505 */
+	AB8500_GPADC_CHAN_MAIN_CHARGER = 0x03,
+	AB8500_GPADC_CHAN_ACC_DET_1 = 0x04,
+	AB8500_GPADC_CHAN_ACC_DET_2 = 0x05,
+	AB8500_GPADC_CHAN_ADC_AUX_1 = 0x06,
+	AB8500_GPADC_CHAN_ADC_AUX_2 = 0x07,
+	AB8500_GPADC_CHAN_VBAT_A = 0x08,
+	AB8500_GPADC_CHAN_VBUS = 0x09,
+	AB8500_GPADC_CHAN_MAIN_CHARGER_CURRENT = 0x0a,
+	AB8500_GPADC_CHAN_USB_CHARGER_CURRENT = 0x0b,
+	AB8500_GPADC_CHAN_BACKUP_BAT = 0x0c,
+	/* Only on AB8505 */
+	AB8505_GPADC_CHAN_DIE_TEMP = 0x0d,
+	AB8500_GPADC_CHAN_ID = 0x0e,
+	AB8500_GPADC_CHAN_INTERNAL_TEST_1 = 0x0f,
+	AB8500_GPADC_CHAN_INTERNAL_TEST_2 = 0x10,
+	AB8500_GPADC_CHAN_INTERNAL_TEST_3 = 0x11,
+	/* FIXME: Applicable to all ASIC variants? */
+	AB8500_GPADC_CHAN_XTAL_TEMP = 0x12,
+	AB8500_GPADC_CHAN_VBAT_TRUE_MEAS = 0x13,
+	/* FIXME: Doesn't seem to work with pure AB8500 */
+	AB8500_GPADC_CHAN_BAT_CTRL_AND_IBAT = 0x1c,
+	AB8500_GPADC_CHAN_VBAT_MEAS_AND_IBAT = 0x1d,
+	AB8500_GPADC_CHAN_VBAT_TRUE_MEAS_AND_IBAT = 0x1e,
+	AB8500_GPADC_CHAN_BAT_TEMP_AND_IBAT = 0x1f,
+	/*
+	 * Virtual channel used only for ibat conversion to ampere.
+	 * Battery current conversion (ibat) cannot be requested as a
+	 * single conversion but it is always requested in combination
+	 * with other input requests.
+	 */
+	AB8500_GPADC_CHAN_IBAT_VIRTUAL = 0xFF,
+};
+
+#define AB8500_GPADC_AUTO_TIMER_REG	0x03
+
+#define AB8500_GPADC_STAT_REG		0x04
+#define AB8500_GPADC_STAT_BUSY		BIT(0)
+
+#define AB8500_GPADC_MANDATAL_REG	0x05
+#define AB8500_GPADC_MANDATAH_REG	0x06
+#define AB8500_GPADC_AUTODATAL_REG	0x07
+#define AB8500_GPADC_AUTODATAH_REG	0x08
+#define AB8500_GPADC_MUX_CTRL_REG	0x09
+#define AB8540_GPADC_MANDATA2L_REG	0x09
+#define AB8540_GPADC_MANDATA2H_REG	0x0A
+#define AB8540_GPADC_APEAAX_REG		0x10
+#define AB8540_GPADC_APEAAT_REG		0x11
+#define AB8540_GPADC_APEAAM_REG		0x12
+#define AB8540_GPADC_APEAAH_REG		0x13
+#define AB8540_GPADC_APEAAL_REG		0x14
+
+/*
+ * OTP register offsets
+ * Bank : 0x15
+ */
+#define AB8500_GPADC_CAL_1	0x0F
+#define AB8500_GPADC_CAL_2	0x10
+#define AB8500_GPADC_CAL_3	0x11
+#define AB8500_GPADC_CAL_4	0x12
+#define AB8500_GPADC_CAL_5	0x13
+#define AB8500_GPADC_CAL_6	0x14
+#define AB8500_GPADC_CAL_7	0x15
+/* New calibration for 8540 */
+#define AB8540_GPADC_OTP4_REG_7	0x38
+#define AB8540_GPADC_OTP4_REG_6	0x39
+#define AB8540_GPADC_OTP4_REG_5	0x3A
+
+#define AB8540_GPADC_DIS_ZERO	0x00
+#define AB8540_GPADC_EN_VBIAS_XTAL_TEMP	0x02
+
+/* GPADC constants from AB8500 spec, UM0836 */
+#define AB8500_ADC_RESOLUTION		1024
+#define AB8500_ADC_CH_BTEMP_MIN		0
+#define AB8500_ADC_CH_BTEMP_MAX		1350
+#define AB8500_ADC_CH_DIETEMP_MIN	0
+#define AB8500_ADC_CH_DIETEMP_MAX	1350
+#define AB8500_ADC_CH_CHG_V_MIN		0
+#define AB8500_ADC_CH_CHG_V_MAX		20030
+#define AB8500_ADC_CH_ACCDET2_MIN	0
+#define AB8500_ADC_CH_ACCDET2_MAX	2500
+#define AB8500_ADC_CH_VBAT_MIN		2300
+#define AB8500_ADC_CH_VBAT_MAX		4800
+#define AB8500_ADC_CH_CHG_I_MIN		0
+#define AB8500_ADC_CH_CHG_I_MAX		1500
+#define AB8500_ADC_CH_BKBAT_MIN		0
+#define AB8500_ADC_CH_BKBAT_MAX		3200
+
+/* GPADC constants from AB8540 spec */
+#define AB8500_ADC_CH_IBAT_MIN		(-6000) /* mA range measured by ADC for ibat */
+#define AB8500_ADC_CH_IBAT_MAX		6000
+#define AB8500_ADC_CH_IBAT_MIN_V	(-60)	/* mV range measured by ADC for ibat */
+#define AB8500_ADC_CH_IBAT_MAX_V	60
+#define AB8500_GPADC_IBAT_VDROP_L	(-56)  /* mV */
+#define AB8500_GPADC_IBAT_VDROP_H	56
+
+/* This is used to not lose precision when dividing to get gain and offset */
+#define AB8500_GPADC_CALIB_SCALE	1000
+/*
+ * Number of bits shift used to not lose precision
+ * when dividing to get ibat gain.
+ */
+#define AB8500_GPADC_CALIB_SHIFT_IBAT	20
+
+/* Time in ms before disabling regulator */
+#define AB8500_GPADC_AUTOSUSPEND_DELAY	1
+
+#define AB8500_GPADC_CONVERSION_TIME	500 /* ms */
+
+enum ab8500_cal_channels {
+	AB8500_CAL_VMAIN = 0,
+	AB8500_CAL_BTEMP,
+	AB8500_CAL_VBAT,
+	AB8500_CAL_IBAT,
+	AB8500_CAL_NR,
+};
+
+/**
+ * struct ab8500_adc_cal_data - Table for storing gain and offset for the
+ * calibrated ADC channels
+ * @gain: Gain of the ADC channel
+ * @offset: Offset of the ADC channel
+ * @otp_calib_hi: Calibration from OTP
+ * @otp_calib_lo: Calibration from OTP
+ */
+struct ab8500_adc_cal_data {
+	s64 gain;
+	s64 offset;
+	u16 otp_calib_hi;
+	u16 otp_calib_lo;
+};
+
+/**
+ * struct ab8500_gpadc_chan_info - per-channel GPADC info
+ * @name: name of the channel
+ * @id: the internal AB8500 ID number for the channel
+ * @hardware_control: indicate that we want to use hardware ADC control
+ * on this channel, the default is software ADC control. Hardware control
+ * is normally only used to test the battery voltage during GSM bursts
+ * and needs a hardware trigger on the GPADCTrig pin of the ASIC.
+ * @falling_edge: indicate that we want to trigger on falling edge
+ * rather than rising edge, rising edge is the default
+ * @avg_sample: how many samples to average: must be 1, 4, 8 or 16.
+ * @trig_timer: how long to wait for the trigger, in 32kHz periods:
+ * 0 .. 255 periods
+ */
+struct ab8500_gpadc_chan_info {
+	const char *name;
+	u8 id;
+	bool hardware_control;
+	bool falling_edge;
+	u8 avg_sample;
+	u8 trig_timer;
+};
+
+/**
+ * struct ab8500_gpadc - AB8500 GPADC device information
+ * @dev: pointer to the containing device
+ * @ab8500: pointer to the parent AB8500 device
+ * @chans: internal per-channel information container
+ * @nchans: number of channels
+ * @complete: pointer to the completion that indicates
+ * the completion of an gpadc conversion cycle
+ * @vddadc: pointer to the regulator supplying VDDADC
+ * @irq_sw: interrupt number that is used by gpadc for software ADC conversion
+ * @irq_hw: interrupt number that is used by gpadc for hardware ADC conversion
+ * @cal_data: array of ADC calibration data structs
+ */
+struct ab8500_gpadc {
+	struct device *dev;
+	struct ab8500 *ab8500;
+	struct ab8500_gpadc_chan_info *chans;
+	unsigned int nchans;
+	struct completion complete;
+	struct regulator *vddadc;
+	int irq_sw;
+	int irq_hw;
+	struct ab8500_adc_cal_data cal_data[AB8500_CAL_NR];
+};
+
+static struct ab8500_gpadc_chan_info *
+ab8500_gpadc_get_channel(struct ab8500_gpadc *gpadc, u8 chan)
+{
+	struct ab8500_gpadc_chan_info *ch;
+	int i;
+
+	for (i = 0; i < gpadc->nchans; i++) {
+		ch = &gpadc->chans[i];
+		if (ch->id == chan)
+			break;
+	}
+	if (i == gpadc->nchans)
+		return NULL;
+
+	return ch;
+}
+
+/**
+ * ab8500_gpadc_ad_to_voltage() - Convert a raw ADC value to a voltage
+ * @gpadc: GPADC instance
+ * @ch: the sampled channel this raw value is coming from
+ * @ad_value: the raw value
+ */
+static int ab8500_gpadc_ad_to_voltage(struct ab8500_gpadc *gpadc,
+				      enum ab8500_gpadc_channel ch,
+				      int ad_value)
+{
+	int res;
+
+	switch (ch) {
+	case AB8500_GPADC_CHAN_MAIN_CHARGER:
+		/* No calibration data available: just interpolate */
+		if (!gpadc->cal_data[AB8500_CAL_VMAIN].gain) {
+			res = AB8500_ADC_CH_CHG_V_MIN + (AB8500_ADC_CH_CHG_V_MAX -
+				AB8500_ADC_CH_CHG_V_MIN) * ad_value /
+				AB8500_ADC_RESOLUTION;
+			break;
+		}
+		/* Here we can use calibration */
+		res = (int) (ad_value * gpadc->cal_data[AB8500_CAL_VMAIN].gain +
+			gpadc->cal_data[AB8500_CAL_VMAIN].offset) / AB8500_GPADC_CALIB_SCALE;
+		break;
+
+	case AB8500_GPADC_CHAN_BAT_CTRL:
+	case AB8500_GPADC_CHAN_BAT_TEMP:
+	case AB8500_GPADC_CHAN_ACC_DET_1:
+	case AB8500_GPADC_CHAN_ADC_AUX_1:
+	case AB8500_GPADC_CHAN_ADC_AUX_2:
+	case AB8500_GPADC_CHAN_XTAL_TEMP:
+		/* No calibration data available: just interpolate */
+		if (!gpadc->cal_data[AB8500_CAL_BTEMP].gain) {
+			res = AB8500_ADC_CH_BTEMP_MIN + (AB8500_ADC_CH_BTEMP_MAX -
+				AB8500_ADC_CH_BTEMP_MIN) * ad_value /
+				AB8500_ADC_RESOLUTION;
+			break;
+		}
+		/* Here we can use calibration */
+		res = (int) (ad_value * gpadc->cal_data[AB8500_CAL_BTEMP].gain +
+			gpadc->cal_data[AB8500_CAL_BTEMP].offset) / AB8500_GPADC_CALIB_SCALE;
+		break;
+
+	case AB8500_GPADC_CHAN_VBAT_A:
+	case AB8500_GPADC_CHAN_VBAT_TRUE_MEAS:
+		/* No calibration data available: just interpolate */
+		if (!gpadc->cal_data[AB8500_CAL_VBAT].gain) {
+			res = AB8500_ADC_CH_VBAT_MIN + (AB8500_ADC_CH_VBAT_MAX -
+				AB8500_ADC_CH_VBAT_MIN) * ad_value /
+				AB8500_ADC_RESOLUTION;
+			break;
+		}
+		/* Here we can use calibration */
+		res = (int) (ad_value * gpadc->cal_data[AB8500_CAL_VBAT].gain +
+			gpadc->cal_data[AB8500_CAL_VBAT].offset) / AB8500_GPADC_CALIB_SCALE;
+		break;
+
+	case AB8505_GPADC_CHAN_DIE_TEMP:
+		res = AB8500_ADC_CH_DIETEMP_MIN +
+			(AB8500_ADC_CH_DIETEMP_MAX - AB8500_ADC_CH_DIETEMP_MIN) * ad_value /
+			AB8500_ADC_RESOLUTION;
+		break;
+
+	case AB8500_GPADC_CHAN_ACC_DET_2:
+		res = AB8500_ADC_CH_ACCDET2_MIN +
+			(AB8500_ADC_CH_ACCDET2_MAX - AB8500_ADC_CH_ACCDET2_MIN) * ad_value /
+			AB8500_ADC_RESOLUTION;
+		break;
+
+	case AB8500_GPADC_CHAN_VBUS:
+		res = AB8500_ADC_CH_CHG_V_MIN +
+			(AB8500_ADC_CH_CHG_V_MAX - AB8500_ADC_CH_CHG_V_MIN) * ad_value /
+			AB8500_ADC_RESOLUTION;
+		break;
+
+	case AB8500_GPADC_CHAN_MAIN_CHARGER_CURRENT:
+	case AB8500_GPADC_CHAN_USB_CHARGER_CURRENT:
+		res = AB8500_ADC_CH_CHG_I_MIN +
+			(AB8500_ADC_CH_CHG_I_MAX - AB8500_ADC_CH_CHG_I_MIN) * ad_value /
+			AB8500_ADC_RESOLUTION;
+		break;
+
+	case AB8500_GPADC_CHAN_BACKUP_BAT:
+		res = AB8500_ADC_CH_BKBAT_MIN +
+			(AB8500_ADC_CH_BKBAT_MAX - AB8500_ADC_CH_BKBAT_MIN) * ad_value /
+			AB8500_ADC_RESOLUTION;
+		break;
+
+	case AB8500_GPADC_CHAN_IBAT_VIRTUAL:
+		/* No calibration data available: just interpolate */
+		if (!gpadc->cal_data[AB8500_CAL_IBAT].gain) {
+			res = AB8500_ADC_CH_IBAT_MIN + (AB8500_ADC_CH_IBAT_MAX -
+				AB8500_ADC_CH_IBAT_MIN) * ad_value /
+				AB8500_ADC_RESOLUTION;
+			break;
+		}
+		/* Here we can use calibration */
+		res = (int) (ad_value * gpadc->cal_data[AB8500_CAL_IBAT].gain +
+				gpadc->cal_data[AB8500_CAL_IBAT].offset)
+				>> AB8500_GPADC_CALIB_SHIFT_IBAT;
+		break;
+
+	default:
+		dev_err(gpadc->dev,
+			"unknown channel ID: %d, not possible to convert\n",
+			ch);
+		res = -EINVAL;
+		break;
+
+	}
+
+	return res;
+}
+
+static int ab8500_gpadc_read(struct ab8500_gpadc *gpadc,
+			     const struct ab8500_gpadc_chan_info *ch,
+			     int *ibat)
+{
+	int ret;
+	int looplimit = 0;
+	unsigned long completion_timeout;
+	u8 val;
+	u8 low_data, high_data, low_data2, high_data2;
+	u8 ctrl1;
+	u8 ctrl23;
+	unsigned int delay_min = 0;
+	unsigned int delay_max = 0;
+	u8 data_low_addr, data_high_addr;
+
+	if (!gpadc)
+		return -ENODEV;
+
+	/* check if conversion is supported */
+	if ((gpadc->irq_sw <= 0) && !ch->hardware_control)
+		return -ENOTSUPP;
+	if ((gpadc->irq_hw <= 0) && ch->hardware_control)
+		return -ENOTSUPP;
+
+	/* Enable vddadc by grabbing PM runtime */
+	pm_runtime_get_sync(gpadc->dev);
+
+	/* Check if ADC is not busy, lock and proceed */
+	do {
+		ret = abx500_get_register_interruptible(gpadc->dev,
+			AB8500_GPADC, AB8500_GPADC_STAT_REG, &val);
+		if (ret < 0)
+			goto out;
+		if (!(val & AB8500_GPADC_STAT_BUSY))
+			break;
+		msleep(20);
+	} while (++looplimit < 10);
+	if (looplimit >= 10 && (val & AB8500_GPADC_STAT_BUSY)) {
+		dev_err(gpadc->dev, "gpadc_conversion: GPADC busy");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	/* Enable GPADC */
+	ctrl1 = AB8500_GPADC_CTRL1_ENABLE;
+
+	/* Select the channel source and set average samples */
+	switch (ch->avg_sample) {
+	case 1:
+		ctrl23 = ch->id | AB8500_GPADC_CTRL2_AVG_1;
+		break;
+	case 4:
+		ctrl23 = ch->id | AB8500_GPADC_CTRL2_AVG_4;
+		break;
+	case 8:
+		ctrl23 = ch->id | AB8500_GPADC_CTRL2_AVG_8;
+		break;
+	default:
+		ctrl23 = ch->id | AB8500_GPADC_CTRL2_AVG_16;
+		break;
+	}
+
+	if (ch->hardware_control) {
+		ret = abx500_set_register_interruptible(gpadc->dev,
+				AB8500_GPADC, AB8500_GPADC_CTRL3_REG, ctrl23);
+		ctrl1 |= AB8500_GPADC_CTRL1_TRIG_ENA;
+		if (ch->falling_edge)
+			ctrl1 |= AB8500_GPADC_CTRL1_TRIG_EDGE;
+	} else {
+		ret = abx500_set_register_interruptible(gpadc->dev,
+				AB8500_GPADC, AB8500_GPADC_CTRL2_REG, ctrl23);
+	}
+	if (ret < 0) {
+		dev_err(gpadc->dev,
+			"gpadc_conversion: set avg samples failed\n");
+		goto out;
+	}
+
+	/*
+	 * Enable ADC, buffering, select rising edge and enable ADC path
+	 * charging current sense if it needed, ABB 3.0 needs some special
+	 * treatment too.
+	 */
+	switch (ch->id) {
+	case AB8500_GPADC_CHAN_MAIN_CHARGER_CURRENT:
+	case AB8500_GPADC_CHAN_USB_CHARGER_CURRENT:
+		ctrl1 |= AB8500_GPADC_CTRL1_BUF_ENA |
+			AB8500_GPADC_CTRL1_ICHAR_ENA;
+		break;
+	case AB8500_GPADC_CHAN_BAT_TEMP:
+		if (!is_ab8500_2p0_or_earlier(gpadc->ab8500)) {
+			ctrl1 |= AB8500_GPADC_CTRL1_BUF_ENA |
+				AB8500_GPADC_CTRL1_BTEMP_PULL_UP;
+			/*
+			 * Delay might be needed for ABB8500 cut 3.0, if not,
+			 * remove when hardware will be available
+			 */
+			delay_min = 1000; /* Delay in micro seconds */
+			delay_max = 10000; /* large range optimises sleepmode */
+			break;
+		}
+		/* Fall through */
+	default:
+		ctrl1 |= AB8500_GPADC_CTRL1_BUF_ENA;
+		break;
+	}
+
+	/* Write configuration to control register 1 */
+	ret = abx500_set_register_interruptible(gpadc->dev,
+		AB8500_GPADC, AB8500_GPADC_CTRL1_REG, ctrl1);
+	if (ret < 0) {
+		dev_err(gpadc->dev,
+			"gpadc_conversion: set Control register failed\n");
+		goto out;
+	}
+
+	if (delay_min != 0)
+		usleep_range(delay_min, delay_max);
+
+	if (ch->hardware_control) {
+		/* Set trigger delay timer */
+		ret = abx500_set_register_interruptible(gpadc->dev,
+			AB8500_GPADC, AB8500_GPADC_AUTO_TIMER_REG,
+			ch->trig_timer);
+		if (ret < 0) {
+			dev_err(gpadc->dev,
+				"gpadc_conversion: trig timer failed\n");
+			goto out;
+		}
+		completion_timeout = 2 * HZ;
+		data_low_addr = AB8500_GPADC_AUTODATAL_REG;
+		data_high_addr = AB8500_GPADC_AUTODATAH_REG;
+	} else {
+		/* Start SW conversion */
+		ret = abx500_mask_and_set_register_interruptible(gpadc->dev,
+			AB8500_GPADC, AB8500_GPADC_CTRL1_REG,
+			AB8500_GPADC_CTRL1_START_SW_CONV,
+			AB8500_GPADC_CTRL1_START_SW_CONV);
+		if (ret < 0) {
+			dev_err(gpadc->dev,
+				"gpadc_conversion: start s/w conv failed\n");
+			goto out;
+		}
+		completion_timeout = msecs_to_jiffies(AB8500_GPADC_CONVERSION_TIME);
+		data_low_addr = AB8500_GPADC_MANDATAL_REG;
+		data_high_addr = AB8500_GPADC_MANDATAH_REG;
+	}
+
+	/* Wait for completion of conversion */
+	if (!wait_for_completion_timeout(&gpadc->complete,
+			completion_timeout)) {
+		dev_err(gpadc->dev,
+			"timeout didn't receive GPADC conv interrupt\n");
+		ret = -EINVAL;
+		goto out;
+	}
+
+	/* Read the converted RAW data */
+	ret = abx500_get_register_interruptible(gpadc->dev,
+			AB8500_GPADC, data_low_addr, &low_data);
+	if (ret < 0) {
+		dev_err(gpadc->dev,
+			"gpadc_conversion: read low data failed\n");
+		goto out;
+	}
+
+	ret = abx500_get_register_interruptible(gpadc->dev,
+		AB8500_GPADC, data_high_addr, &high_data);
+	if (ret < 0) {
+		dev_err(gpadc->dev,
+			"gpadc_conversion: read high data failed\n");
+		goto out;
+	}
+
+	/* Check if double conversion is required */
+	if ((ch->id == AB8500_GPADC_CHAN_BAT_CTRL_AND_IBAT) ||
+	    (ch->id == AB8500_GPADC_CHAN_VBAT_MEAS_AND_IBAT) ||
+	    (ch->id == AB8500_GPADC_CHAN_VBAT_TRUE_MEAS_AND_IBAT) ||
+	    (ch->id == AB8500_GPADC_CHAN_BAT_TEMP_AND_IBAT)) {
+
+		if (ch->hardware_control) {
+			/* not supported */
+			ret = -ENOTSUPP;
+			dev_err(gpadc->dev,
+				"gpadc_conversion: only SW double conversion supported\n");
+			goto out;
+		} else {
+			/* Read the converted RAW data 2 */
+			ret = abx500_get_register_interruptible(gpadc->dev,
+				AB8500_GPADC, AB8540_GPADC_MANDATA2L_REG,
+				&low_data2);
+			if (ret < 0) {
+				dev_err(gpadc->dev,
+					"gpadc_conversion: read sw low data 2 failed\n");
+				goto out;
+			}
+
+			ret = abx500_get_register_interruptible(gpadc->dev,
+				AB8500_GPADC, AB8540_GPADC_MANDATA2H_REG,
+				&high_data2);
+			if (ret < 0) {
+				dev_err(gpadc->dev,
+					"gpadc_conversion: read sw high data 2 failed\n");
+				goto out;
+			}
+			if (ibat != NULL) {
+				*ibat = (high_data2 << 8) | low_data2;
+			} else {
+				dev_warn(gpadc->dev,
+					"gpadc_conversion: ibat not stored\n");
+			}
+
+		}
+	}
+
+	/* Disable GPADC */
+	ret = abx500_set_register_interruptible(gpadc->dev, AB8500_GPADC,
+		AB8500_GPADC_CTRL1_REG, AB8500_GPADC_CTRL1_DISABLE);
+	if (ret < 0) {
+		dev_err(gpadc->dev, "gpadc_conversion: disable gpadc failed\n");
+		goto out;
+	}
+
+	/* This eventually drops the regulator */
+	pm_runtime_mark_last_busy(gpadc->dev);
+	pm_runtime_put_autosuspend(gpadc->dev);
+
+	return (high_data << 8) | low_data;
+
+out:
+	/*
+	 * It has shown to be needed to turn off the GPADC if an error occurs,
+	 * otherwise we might have problem when waiting for the busy bit in the
+	 * GPADC status register to go low. In V1.1 there wait_for_completion
+	 * seems to timeout when waiting for an interrupt.. Not seen in V2.0
+	 */
+	(void) abx500_set_register_interruptible(gpadc->dev, AB8500_GPADC,
+		AB8500_GPADC_CTRL1_REG, AB8500_GPADC_CTRL1_DISABLE);
+	pm_runtime_put(gpadc->dev);
+	dev_err(gpadc->dev,
+		"gpadc_conversion: Failed to AD convert channel %d\n", ch->id);
+
+	return ret;
+}
+
+/**
+ * ab8500_bm_gpadcconvend_handler() - isr for gpadc conversion completion
+ * @irq: irq number
+ * @data: pointer to the data passed during request irq
+ *
+ * This is a interrupt service routine for gpadc conversion completion.
+ * Notifies the gpadc completion is completed and the converted raw value
+ * can be read from the registers.
+ * Returns IRQ status(IRQ_HANDLED)
+ */
+static irqreturn_t ab8500_bm_gpadcconvend_handler(int irq, void *data)
+{
+	struct ab8500_gpadc *gpadc = data;
+
+	complete(&gpadc->complete);
+
+	return IRQ_HANDLED;
+}
+
+static int otp_cal_regs[] = {
+	AB8500_GPADC_CAL_1,
+	AB8500_GPADC_CAL_2,
+	AB8500_GPADC_CAL_3,
+	AB8500_GPADC_CAL_4,
+	AB8500_GPADC_CAL_5,
+	AB8500_GPADC_CAL_6,
+	AB8500_GPADC_CAL_7,
+};
+
+static int otp4_cal_regs[] = {
+	AB8540_GPADC_OTP4_REG_7,
+	AB8540_GPADC_OTP4_REG_6,
+	AB8540_GPADC_OTP4_REG_5,
+};
+
+static void ab8500_gpadc_read_calibration_data(struct ab8500_gpadc *gpadc)
+{
+	int i;
+	int ret[ARRAY_SIZE(otp_cal_regs)];
+	u8 gpadc_cal[ARRAY_SIZE(otp_cal_regs)];
+	int ret_otp4[ARRAY_SIZE(otp4_cal_regs)];
+	u8 gpadc_otp4[ARRAY_SIZE(otp4_cal_regs)];
+	int vmain_high, vmain_low;
+	int btemp_high, btemp_low;
+	int vbat_high, vbat_low;
+	int ibat_high, ibat_low;
+	s64 V_gain, V_offset, V2A_gain, V2A_offset;
+
+	/* First we read all OTP registers and store the error code */
+	for (i = 0; i < ARRAY_SIZE(otp_cal_regs); i++) {
+		ret[i] = abx500_get_register_interruptible(gpadc->dev,
+			AB8500_OTP_EMUL, otp_cal_regs[i],  &gpadc_cal[i]);
+		if (ret[i] < 0) {
+			/* Continue anyway: maybe the other registers are OK */
+			dev_err(gpadc->dev, "%s: read otp reg 0x%02x failed\n",
+				__func__, otp_cal_regs[i]);
+		} else {
+			/* Put this in the entropy pool as device-unique */
+			add_device_randomness(&ret[i], sizeof(ret[i]));
+		}
+	}
+
+	/*
+	 * The ADC calibration data is stored in OTP registers.
+	 * The layout of the calibration data is outlined below and a more
+	 * detailed description can be found in UM0836
+	 *
+	 * vm_h/l = vmain_high/low
+	 * bt_h/l = btemp_high/low
+	 * vb_h/l = vbat_high/low
+	 *
+	 * Data bits 8500/9540:
+	 * | 7	   | 6	   | 5	   | 4	   | 3	   | 2	   | 1	   | 0
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * |						   | vm_h9 | vm_h8
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * |		   | vm_h7 | vm_h6 | vm_h5 | vm_h4 | vm_h3 | vm_h2
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | vm_h1 | vm_h0 | vm_l4 | vm_l3 | vm_l2 | vm_l1 | vm_l0 | bt_h9
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | bt_h8 | bt_h7 | bt_h6 | bt_h5 | bt_h4 | bt_h3 | bt_h2 | bt_h1
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | bt_h0 | bt_l4 | bt_l3 | bt_l2 | bt_l1 | bt_l0 | vb_h9 | vb_h8
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | vb_h7 | vb_h6 | vb_h5 | vb_h4 | vb_h3 | vb_h2 | vb_h1 | vb_h0
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | vb_l5 | vb_l4 | vb_l3 | vb_l2 | vb_l1 | vb_l0 |
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 *
+	 * Data bits 8540:
+	 * OTP2
+	 * | 7	   | 6	   | 5	   | 4	   | 3	   | 2	   | 1	   | 0
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * |
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | vm_h9 | vm_h8 | vm_h7 | vm_h6 | vm_h5 | vm_h4 | vm_h3 | vm_h2
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | vm_h1 | vm_h0 | vm_l4 | vm_l3 | vm_l2 | vm_l1 | vm_l0 | bt_h9
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | bt_h8 | bt_h7 | bt_h6 | bt_h5 | bt_h4 | bt_h3 | bt_h2 | bt_h1
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | bt_h0 | bt_l4 | bt_l3 | bt_l2 | bt_l1 | bt_l0 | vb_h9 | vb_h8
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | vb_h7 | vb_h6 | vb_h5 | vb_h4 | vb_h3 | vb_h2 | vb_h1 | vb_h0
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | vb_l5 | vb_l4 | vb_l3 | vb_l2 | vb_l1 | vb_l0 |
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 *
+	 * Data bits 8540:
+	 * OTP4
+	 * | 7	   | 6	   | 5	   | 4	   | 3	   | 2	   | 1	   | 0
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * |					   | ib_h9 | ib_h8 | ib_h7
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | ib_h6 | ib_h5 | ib_h4 | ib_h3 | ib_h2 | ib_h1 | ib_h0 | ib_l5
+	 * |.......|.......|.......|.......|.......|.......|.......|.......
+	 * | ib_l4 | ib_l3 | ib_l2 | ib_l1 | ib_l0 |
+	 *
+	 *
+	 * Ideal output ADC codes corresponding to injected input voltages
+	 * during manufacturing is:
+	 *
+	 * vmain_high: Vin = 19500mV / ADC ideal code = 997
+	 * vmain_low:  Vin = 315mV   / ADC ideal code = 16
+	 * btemp_high: Vin = 1300mV  / ADC ideal code = 985
+	 * btemp_low:  Vin = 21mV    / ADC ideal code = 16
+	 * vbat_high:  Vin = 4700mV  / ADC ideal code = 982
+	 * vbat_low:   Vin = 2380mV  / ADC ideal code = 33
+	 */
+
+	if (is_ab8540(gpadc->ab8500)) {
+		/* Calculate gain and offset for VMAIN if all reads succeeded*/
+		if (!(ret[1] < 0 || ret[2] < 0)) {
+			vmain_high = (((gpadc_cal[1] & 0xFF) << 2) |
+				((gpadc_cal[2] & 0xC0) >> 6));
+			vmain_low = ((gpadc_cal[2] & 0x3E) >> 1);
+
+			gpadc->cal_data[AB8500_CAL_VMAIN].otp_calib_hi =
+				(u16)vmain_high;
+			gpadc->cal_data[AB8500_CAL_VMAIN].otp_calib_lo =
+				(u16)vmain_low;
+
+			gpadc->cal_data[AB8500_CAL_VMAIN].gain = AB8500_GPADC_CALIB_SCALE *
+				(19500 - 315) / (vmain_high - vmain_low);
+			gpadc->cal_data[AB8500_CAL_VMAIN].offset = AB8500_GPADC_CALIB_SCALE *
+				19500 - (AB8500_GPADC_CALIB_SCALE * (19500 - 315) /
+				(vmain_high - vmain_low)) * vmain_high;
+		} else {
+			gpadc->cal_data[AB8500_CAL_VMAIN].gain = 0;
+		}
+
+		/* Read IBAT calibration Data */
+		for (i = 0; i < ARRAY_SIZE(otp4_cal_regs); i++) {
+			ret_otp4[i] = abx500_get_register_interruptible(
+					gpadc->dev, AB8500_OTP_EMUL,
+					otp4_cal_regs[i],  &gpadc_otp4[i]);
+			if (ret_otp4[i] < 0)
+				dev_err(gpadc->dev,
+					"%s: read otp4 reg 0x%02x failed\n",
+					__func__, otp4_cal_regs[i]);
+		}
+
+		/* Calculate gain and offset for IBAT if all reads succeeded */
+		if (!(ret_otp4[0] < 0 || ret_otp4[1] < 0 || ret_otp4[2] < 0)) {
+			ibat_high = (((gpadc_otp4[0] & 0x07) << 7) |
+				((gpadc_otp4[1] & 0xFE) >> 1));
+			ibat_low = (((gpadc_otp4[1] & 0x01) << 5) |
+				((gpadc_otp4[2] & 0xF8) >> 3));
+
+			gpadc->cal_data[AB8500_CAL_IBAT].otp_calib_hi =
+				(u16)ibat_high;
+			gpadc->cal_data[AB8500_CAL_IBAT].otp_calib_lo =
+				(u16)ibat_low;
+
+			V_gain = ((AB8500_GPADC_IBAT_VDROP_H - AB8500_GPADC_IBAT_VDROP_L)
+				<< AB8500_GPADC_CALIB_SHIFT_IBAT) / (ibat_high - ibat_low);
+
+			V_offset = (AB8500_GPADC_IBAT_VDROP_H << AB8500_GPADC_CALIB_SHIFT_IBAT) -
+				(((AB8500_GPADC_IBAT_VDROP_H - AB8500_GPADC_IBAT_VDROP_L) <<
+				AB8500_GPADC_CALIB_SHIFT_IBAT) / (ibat_high - ibat_low))
+				* ibat_high;
+			/*
+			 * Result obtained is in mV (at a scale factor),
+			 * we need to calculate gain and offset to get mA
+			 */
+			V2A_gain = (AB8500_ADC_CH_IBAT_MAX - AB8500_ADC_CH_IBAT_MIN)/
+				(AB8500_ADC_CH_IBAT_MAX_V - AB8500_ADC_CH_IBAT_MIN_V);
+			V2A_offset = ((AB8500_ADC_CH_IBAT_MAX_V * AB8500_ADC_CH_IBAT_MIN -
+				AB8500_ADC_CH_IBAT_MAX * AB8500_ADC_CH_IBAT_MIN_V)
+				<< AB8500_GPADC_CALIB_SHIFT_IBAT)
+				/ (AB8500_ADC_CH_IBAT_MAX_V - AB8500_ADC_CH_IBAT_MIN_V);
+
+			gpadc->cal_data[AB8500_CAL_IBAT].gain =
+				V_gain * V2A_gain;
+			gpadc->cal_data[AB8500_CAL_IBAT].offset =
+				V_offset * V2A_gain + V2A_offset;
+		} else {
+			gpadc->cal_data[AB8500_CAL_IBAT].gain = 0;
+		}
+	} else {
+		/* Calculate gain and offset for VMAIN if all reads succeeded */
+		if (!(ret[0] < 0 || ret[1] < 0 || ret[2] < 0)) {
+			vmain_high = (((gpadc_cal[0] & 0x03) << 8) |
+				((gpadc_cal[1] & 0x3F) << 2) |
+				((gpadc_cal[2] & 0xC0) >> 6));
+			vmain_low = ((gpadc_cal[2] & 0x3E) >> 1);
+
+			gpadc->cal_data[AB8500_CAL_VMAIN].otp_calib_hi =
+				(u16)vmain_high;
+			gpadc->cal_data[AB8500_CAL_VMAIN].otp_calib_lo =
+				(u16)vmain_low;
+
+			gpadc->cal_data[AB8500_CAL_VMAIN].gain = AB8500_GPADC_CALIB_SCALE *
+				(19500 - 315) / (vmain_high - vmain_low);
+
+			gpadc->cal_data[AB8500_CAL_VMAIN].offset = AB8500_GPADC_CALIB_SCALE *
+				19500 - (AB8500_GPADC_CALIB_SCALE * (19500 - 315) /
+				(vmain_high - vmain_low)) * vmain_high;
+		} else {
+			gpadc->cal_data[AB8500_CAL_VMAIN].gain = 0;
+		}
+	}
+
+	/* Calculate gain and offset for BTEMP if all reads succeeded */
+	if (!(ret[2] < 0 || ret[3] < 0 || ret[4] < 0)) {
+		btemp_high = (((gpadc_cal[2] & 0x01) << 9) |
+			(gpadc_cal[3] << 1) | ((gpadc_cal[4] & 0x80) >> 7));
+		btemp_low = ((gpadc_cal[4] & 0x7C) >> 2);
+
+		gpadc->cal_data[AB8500_CAL_BTEMP].otp_calib_hi = (u16)btemp_high;
+		gpadc->cal_data[AB8500_CAL_BTEMP].otp_calib_lo = (u16)btemp_low;
+
+		gpadc->cal_data[AB8500_CAL_BTEMP].gain =
+			AB8500_GPADC_CALIB_SCALE * (1300 - 21) / (btemp_high - btemp_low);
+		gpadc->cal_data[AB8500_CAL_BTEMP].offset = AB8500_GPADC_CALIB_SCALE * 1300 -
+			(AB8500_GPADC_CALIB_SCALE * (1300 - 21) / (btemp_high - btemp_low))
+			* btemp_high;
+	} else {
+		gpadc->cal_data[AB8500_CAL_BTEMP].gain = 0;
+	}
+
+	/* Calculate gain and offset for VBAT if all reads succeeded */
+	if (!(ret[4] < 0 || ret[5] < 0 || ret[6] < 0)) {
+		vbat_high = (((gpadc_cal[4] & 0x03) << 8) | gpadc_cal[5]);
+		vbat_low = ((gpadc_cal[6] & 0xFC) >> 2);
+
+		gpadc->cal_data[AB8500_CAL_VBAT].otp_calib_hi = (u16)vbat_high;
+		gpadc->cal_data[AB8500_CAL_VBAT].otp_calib_lo = (u16)vbat_low;
+
+		gpadc->cal_data[AB8500_CAL_VBAT].gain = AB8500_GPADC_CALIB_SCALE *
+			(4700 - 2380) /	(vbat_high - vbat_low);
+		gpadc->cal_data[AB8500_CAL_VBAT].offset = AB8500_GPADC_CALIB_SCALE * 4700 -
+			(AB8500_GPADC_CALIB_SCALE * (4700 - 2380) /
+			(vbat_high - vbat_low)) * vbat_high;
+	} else {
+		gpadc->cal_data[AB8500_CAL_VBAT].gain = 0;
+	}
+}
+
+static int ab8500_gpadc_read_raw(struct iio_dev *indio_dev,
+				 struct iio_chan_spec const *chan,
+				 int *val, int *val2, long mask)
+{
+	struct ab8500_gpadc *gpadc = iio_priv(indio_dev);
+	const struct ab8500_gpadc_chan_info *ch;
+	int raw_val;
+	int processed;
+
+	ch = ab8500_gpadc_get_channel(gpadc, chan->address);
+	if (!ch) {
+		dev_err(gpadc->dev, "no such channel %lu\n",
+			chan->address);
+		return -EINVAL;
+	}
+
+	raw_val = ab8500_gpadc_read(gpadc, ch, NULL);
+	if (raw_val < 0)
+		return raw_val;
+
+	if (mask == IIO_CHAN_INFO_RAW) {
+		*val = raw_val;
+		return IIO_VAL_INT;
+	}
+
+	if (mask == IIO_CHAN_INFO_PROCESSED) {
+		processed = ab8500_gpadc_ad_to_voltage(gpadc, ch->id, raw_val);
+		if (processed < 0)
+			return processed;
+
+		/* Return millivolt or milliamps or millicentigrades */
+		*val = processed * 1000;
+		return IIO_VAL_INT;
+	}
+
+	return -EINVAL;
+}
+
+static int ab8500_gpadc_of_xlate(struct iio_dev *indio_dev,
+				 const struct of_phandle_args *iiospec)
+{
+	int i;
+
+	for (i = 0; i < indio_dev->num_channels; i++)
+		if (indio_dev->channels[i].channel == iiospec->args[0])
+			return i;
+
+	return -EINVAL;
+}
+
+static const struct iio_info ab8500_gpadc_info = {
+	.of_xlate = ab8500_gpadc_of_xlate,
+	.read_raw = ab8500_gpadc_read_raw,
+};
+
+#ifdef CONFIG_PM
+static int ab8500_gpadc_runtime_suspend(struct device *dev)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct ab8500_gpadc *gpadc = iio_priv(indio_dev);
+
+	regulator_disable(gpadc->vddadc);
+
+	return 0;
+}
+
+static int ab8500_gpadc_runtime_resume(struct device *dev)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct ab8500_gpadc *gpadc = iio_priv(indio_dev);
+	int ret;
+
+	ret = regulator_enable(gpadc->vddadc);
+	if (ret)
+		dev_err(dev, "Failed to enable vddadc: %d\n", ret);
+
+	return ret;
+}
+#endif
+
+/**
+ * ab8500_gpadc_parse_channel() - process devicetree channel configuration
+ * @dev: pointer to containing device
+ * @np: device tree node for the channel to configure
+ * @ch: channel info to fill in
+ * @iio_chan: IIO channel specification to fill in
+ *
+ * The devicetree will set up the channel for use with the specific device,
+ * and define usage for things like AUX GPADC inputs more precisely.
+ */
+static int ab8500_gpadc_parse_channel(struct device *dev,
+				      struct device_node *np,
+				      struct ab8500_gpadc_chan_info *ch,
+				      struct iio_chan_spec *iio_chan)
+{
+	const char *name = np->name;
+	u32 chan;
+	int ret;
+
+	ret = of_property_read_u32(np, "reg", &chan);
+	if (ret) {
+		dev_err(dev, "invalid channel number %s\n", name);
+		return ret;
+	}
+	if (chan > AB8500_GPADC_CHAN_BAT_TEMP_AND_IBAT) {
+		dev_err(dev, "%s channel number out of range %d\n", name, chan);
+		return -EINVAL;
+	}
+
+	iio_chan->channel = chan;
+	iio_chan->datasheet_name = name;
+	iio_chan->indexed = 1;
+	iio_chan->address = chan;
+	iio_chan->info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+		BIT(IIO_CHAN_INFO_PROCESSED);
+	/* Most are voltages (also temperatures), some are currents */
+	if ((chan == AB8500_GPADC_CHAN_MAIN_CHARGER_CURRENT) ||
+	    (chan == AB8500_GPADC_CHAN_USB_CHARGER_CURRENT))
+		iio_chan->type = IIO_CURRENT;
+	else
+		iio_chan->type = IIO_VOLTAGE;
+
+	ch->id = chan;
+
+	/* Sensible defaults */
+	ch->avg_sample = 16;
+	ch->hardware_control = false;
+	ch->falling_edge = false;
+	ch->trig_timer = 0;
+
+	return 0;
+}
+
+/**
+ * ab8500_gpadc_parse_channels() - Parse the GPADC channels from DT
+ * @gpadc: the GPADC to configure the channels for
+ * @np: device tree node containing the channel configurations
+ * @chans: the IIO channels we parsed
+ * @nchans: the number of IIO channels we parsed
+ */
+static int ab8500_gpadc_parse_channels(struct ab8500_gpadc *gpadc,
+				       struct device_node *np,
+				       struct iio_chan_spec **chans_parsed,
+				       unsigned int *nchans_parsed)
+{
+	struct device_node *child;
+	struct ab8500_gpadc_chan_info *ch;
+	struct iio_chan_spec *iio_chans;
+	unsigned int nchans;
+	int i;
+
+	nchans = of_get_available_child_count(np);
+	if (!nchans) {
+		dev_err(gpadc->dev, "no channel children\n");
+		return -ENODEV;
+	}
+	dev_info(gpadc->dev, "found %d ADC channels\n", nchans);
+
+	iio_chans = devm_kcalloc(gpadc->dev, nchans,
+				 sizeof(*iio_chans), GFP_KERNEL);
+	if (!iio_chans)
+		return -ENOMEM;
+
+	gpadc->chans = devm_kcalloc(gpadc->dev, nchans,
+				    sizeof(*gpadc->chans), GFP_KERNEL);
+	if (!gpadc->chans)
+		return -ENOMEM;
+
+	i = 0;
+	for_each_available_child_of_node(np, child) {
+		struct iio_chan_spec *iio_chan;
+		int ret;
+
+		ch = &gpadc->chans[i];
+		iio_chan = &iio_chans[i];
+
+		ret = ab8500_gpadc_parse_channel(gpadc->dev, child, ch,
+						 iio_chan);
+		if (ret) {
+			of_node_put(child);
+			return ret;
+		}
+		i++;
+	}
+	gpadc->nchans = nchans;
+	*chans_parsed = iio_chans;
+	*nchans_parsed = nchans;
+
+	return 0;
+}
+
+static int ab8500_gpadc_probe(struct platform_device *pdev)
+{
+	struct ab8500_gpadc *gpadc;
+	struct iio_dev *indio_dev;
+	struct device *dev = &pdev->dev;
+	struct device_node *np = pdev->dev.of_node;
+	struct iio_chan_spec *iio_chans;
+	unsigned int n_iio_chans;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*gpadc));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, indio_dev);
+	gpadc = iio_priv(indio_dev);
+
+	gpadc->dev = dev;
+	gpadc->ab8500 = dev_get_drvdata(dev->parent);
+
+	ret = ab8500_gpadc_parse_channels(gpadc, np, &iio_chans, &n_iio_chans);
+	if (ret)
+		return ret;
+
+	gpadc->irq_sw = platform_get_irq_byname(pdev, "SW_CONV_END");
+	if (gpadc->irq_sw < 0) {
+		dev_err(dev, "failed to get platform sw_conv_end irq\n");
+		return gpadc->irq_sw;
+	}
+
+	gpadc->irq_hw = platform_get_irq_byname(pdev, "HW_CONV_END");
+	if (gpadc->irq_hw < 0) {
+		dev_err(dev, "failed to get platform hw_conv_end irq\n");
+		return gpadc->irq_hw;
+	}
+
+	/* Initialize completion used to notify completion of conversion */
+	init_completion(&gpadc->complete);
+
+	/* Request interrupts */
+	ret = devm_request_threaded_irq(dev, gpadc->irq_sw, NULL,
+		ab8500_bm_gpadcconvend_handler,	IRQF_NO_SUSPEND | IRQF_ONESHOT,
+		"ab8500-gpadc-sw", gpadc);
+	if (ret < 0) {
+		dev_err(dev,
+			"failed to request sw conversion irq %d\n",
+			gpadc->irq_sw);
+		return ret;
+	}
+
+	ret = devm_request_threaded_irq(dev, gpadc->irq_hw, NULL,
+		ab8500_bm_gpadcconvend_handler,	IRQF_NO_SUSPEND | IRQF_ONESHOT,
+		"ab8500-gpadc-hw", gpadc);
+	if (ret < 0) {
+		dev_err(dev,
+			"Failed to request hw conversion irq: %d\n",
+			gpadc->irq_hw);
+		return ret;
+	}
+
+	/* The VTVout LDO used to power the AB8500 GPADC */
+	gpadc->vddadc = devm_regulator_get(dev, "vddadc");
+	if (IS_ERR(gpadc->vddadc)) {
+		ret = PTR_ERR(gpadc->vddadc);
+		dev_err(dev, "failed to get vddadc\n");
+		return ret;
+	}
+
+	ret = regulator_enable(gpadc->vddadc);
+	if (ret) {
+		dev_err(dev, "failed to enable vddadc: %d\n", ret);
+		return ret;
+	}
+
+	/* Enable runtime PM */
+	pm_runtime_get_noresume(dev);
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+	pm_runtime_set_autosuspend_delay(dev, AB8500_GPADC_AUTOSUSPEND_DELAY);
+	pm_runtime_use_autosuspend(dev);
+
+	ab8500_gpadc_read_calibration_data(gpadc);
+
+	pm_runtime_put(dev);
+
+	indio_dev->dev.parent = dev;
+	indio_dev->dev.of_node = np;
+	indio_dev->name = "ab8500-gpadc";
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->info = &ab8500_gpadc_info;
+	indio_dev->channels = iio_chans;
+	indio_dev->num_channels = n_iio_chans;
+
+	ret = devm_iio_device_register(dev, indio_dev);
+	if (ret)
+		goto out_dis_pm;
+
+	return 0;
+
+out_dis_pm:
+	pm_runtime_get_sync(dev);
+	pm_runtime_put_noidle(dev);
+	pm_runtime_disable(dev);
+	regulator_disable(gpadc->vddadc);
+
+	return ret;
+}
+
+static int ab8500_gpadc_remove(struct platform_device *pdev)
+{
+	struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+	struct ab8500_gpadc *gpadc = iio_priv(indio_dev);
+
+	pm_runtime_get_sync(gpadc->dev);
+	pm_runtime_put_noidle(gpadc->dev);
+	pm_runtime_disable(gpadc->dev);
+	regulator_disable(gpadc->vddadc);
+
+	return 0;
+}
+
+static const struct dev_pm_ops ab8500_gpadc_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+				pm_runtime_force_resume)
+	SET_RUNTIME_PM_OPS(ab8500_gpadc_runtime_suspend,
+			   ab8500_gpadc_runtime_resume,
+			   NULL)
+};
+
+static struct platform_driver ab8500_gpadc_driver = {
+	.probe = ab8500_gpadc_probe,
+	.remove = ab8500_gpadc_remove,
+	.driver = {
+		.name = "ab8500-gpadc",
+		.pm = &ab8500_gpadc_pm_ops,
+	},
+};
+builtin_platform_driver(ab8500_gpadc_driver);
