| Message ID | 20191206131944.28707-1-geert+renesas@glider.be (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | [v3] iio: adc: max9611: Fix too short conversion time delay | expand |
On Fri, 6 Dec 2019 14:19:44 +0100 Geert Uytterhoeven <geert+renesas@glider.be> wrote: > As of commit b9ddd5091160793e ("iio: adc: max9611: Fix temperature > reading in probe"), max9611 initialization sometimes fails on the > Salvator-X(S) development board with: > > max9611 4-007f: Invalid value received from ADC 0x8000: aborting > max9611: probe of 4-007f failed with error -5 > > The max9611 driver tests communications with the chip by reading the die > temperature during the probe function, which returns an invalid value. > > According to the datasheet, the typical ADC conversion time is 2 ms, but > no minimum or maximum values are provided. Maxim Technical Support > confirmed this was tested with temperature Ta=25 degreeC, and promised > to inform me if a maximum/minimum value is available (they didn't get > back to me, so I assume it is not). > > However, the driver assumes a 1 ms conversion time. Usually the > usleep_range() call returns after more than 1.8 ms, hence it succeeds. > When it returns earlier, the data register may be read too early, and > the previous measurement value will be returned. After boot, this is > the temperature POR (power-on reset) value, causing the failure above. > > Fix this by increasing the delay from 1000-2000 µs to 3000-3300 µs. > > Note that this issue has always been present, but it was exposed by the > aformentioned commit. > > Fixes: 69780a3bbc0b1e7e ("iio: adc: Add Maxim max9611 ADC driver") > Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> > Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org> > Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Ah. I picked up v2 and did the tidy up. Oh well, same result ;) Jonathan > --- > After this patch, probing of the two max9611 sensors succeeded during > ca. 3000 boot cycles on Salvator-X(S) boards, equipped with various > R-Car H3/M3-W/M3-N SoCs. > > v3: > - Add Reviewed-by, > - Join split comment line, > > v2: > - Add Reviewed-by, > - Add feedback from Maxim Technical Support, > - Increase delay from 2000-2200 µs to 3000-3300 µs to play safe. > --- > drivers/iio/adc/max9611.c | 13 +++++++++---- > 1 file changed, 9 insertions(+), 4 deletions(-) > > diff --git a/drivers/iio/adc/max9611.c b/drivers/iio/adc/max9611.c > index bf76dfb3f2c9530b..6250d4bf46dc9642 100644 > --- a/drivers/iio/adc/max9611.c > +++ b/drivers/iio/adc/max9611.c > @@ -89,6 +89,12 @@ > #define MAX9611_TEMP_SCALE_NUM 1000000 > #define MAX9611_TEMP_SCALE_DIV 2083 > > +/* > + * Conversion time is 2 ms (typically) at Ta=25 degreeC > + * No maximum value is known, so play it safe > + */ > +#define MAX9611_CONV_TIME_US_RANGE 3000, 3300 > + > struct max9611_dev { > struct device *dev; > struct i2c_client *i2c_client; > @@ -223,10 +229,9 @@ static int max9611_read_single(struct max9611_dev *max9611, > } > > /* > - * need a delay here to make register configuration > - * stabilize. 1 msec at least, from empirical testing. > + * need a delay here to make register configuration stabilize. > */ > - usleep_range(1000, 2000); > + usleep_range(MAX9611_CONV_TIME_US_RANGE); > > ret = i2c_smbus_read_word_swapped(max9611->i2c_client, reg_addr); > if (ret < 0) { > @@ -493,7 +498,7 @@ static int max9611_init(struct max9611_dev *max9611) > MAX9611_REG_CTRL2, 0); > return ret; > } > - usleep_range(1000, 2000); > + usleep_range(MAX9611_CONV_TIME_US_RANGE); > > return 0; > }
diff --git a/drivers/iio/adc/max9611.c b/drivers/iio/adc/max9611.c index bf76dfb3f2c9530b..6250d4bf46dc9642 100644 --- a/drivers/iio/adc/max9611.c +++ b/drivers/iio/adc/max9611.c @@ -89,6 +89,12 @@ #define MAX9611_TEMP_SCALE_NUM 1000000 #define MAX9611_TEMP_SCALE_DIV 2083 +/* + * Conversion time is 2 ms (typically) at Ta=25 degreeC + * No maximum value is known, so play it safe + */ +#define MAX9611_CONV_TIME_US_RANGE 3000, 3300 + struct max9611_dev { struct device *dev; struct i2c_client *i2c_client; @@ -223,10 +229,9 @@ static int max9611_read_single(struct max9611_dev *max9611, } /* - * need a delay here to make register configuration - * stabilize. 1 msec at least, from empirical testing. + * need a delay here to make register configuration stabilize. */ - usleep_range(1000, 2000); + usleep_range(MAX9611_CONV_TIME_US_RANGE); ret = i2c_smbus_read_word_swapped(max9611->i2c_client, reg_addr); if (ret < 0) { @@ -493,7 +498,7 @@ static int max9611_init(struct max9611_dev *max9611) MAX9611_REG_CTRL2, 0); return ret; } - usleep_range(1000, 2000); + usleep_range(MAX9611_CONV_TIME_US_RANGE); return 0; }
As of commit b9ddd5091160793e ("iio: adc: max9611: Fix temperature reading in probe"), max9611 initialization sometimes fails on the Salvator-X(S) development board with: max9611 4-007f: Invalid value received from ADC 0x8000: aborting max9611: probe of 4-007f failed with error -5 The max9611 driver tests communications with the chip by reading the die temperature during the probe function, which returns an invalid value. According to the datasheet, the typical ADC conversion time is 2 ms, but no minimum or maximum values are provided. Maxim Technical Support confirmed this was tested with temperature Ta=25 degreeC, and promised to inform me if a maximum/minimum value is available (they didn't get back to me, so I assume it is not). However, the driver assumes a 1 ms conversion time. Usually the usleep_range() call returns after more than 1.8 ms, hence it succeeds. When it returns earlier, the data register may be read too early, and the previous measurement value will be returned. After boot, this is the temperature POR (power-on reset) value, causing the failure above. Fix this by increasing the delay from 1000-2000 µs to 3000-3300 µs. Note that this issue has always been present, but it was exposed by the aformentioned commit. Fixes: 69780a3bbc0b1e7e ("iio: adc: Add Maxim max9611 ADC driver") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> --- After this patch, probing of the two max9611 sensors succeeded during ca. 3000 boot cycles on Salvator-X(S) boards, equipped with various R-Car H3/M3-W/M3-N SoCs. v3: - Add Reviewed-by, - Join split comment line, v2: - Add Reviewed-by, - Add feedback from Maxim Technical Support, - Increase delay from 2000-2200 µs to 3000-3300 µs to play safe. --- drivers/iio/adc/max9611.c | 13 +++++++++---- 1 file changed, 9 insertions(+), 4 deletions(-)