@@ -18013,6 +18013,14 @@ S: Supported
F: Documentation/devicetree/bindings/net/nfc/trf7970a.txt
F: drivers/nfc/trf7970a.c
+TI TSC2046 ADC DRIVER
+M: Oleksij Rempel <o.rempel@pengutronix.de>
+R: kernel@pengutronix.de
+L: linux-iio@vger.kernel.org
+S: Maintained
+F: Documentation/devicetree/bindings/iio/adc/ti,tsc2046.yaml
+F: drivers/iio/adc/ti-tsc2046.c
+
TI TWL4030 SERIES SOC CODEC DRIVER
M: Peter Ujfalusi <peter.ujfalusi@gmail.com>
L: alsa-devel@alsa-project.org (moderated for non-subscribers)
@@ -1188,6 +1188,18 @@ config TI_TLC4541
This driver can also be built as a module. If so, the module will be
called ti-tlc4541.
+config TI_TSC2046
+ tristate "Texas Instruments TSC2046 ADC driver"
+ depends on SPI
+ select IIO_BUFFER
+ select IIO_TRIGGERED_BUFFER
+ help
+ Say yes here to build support for ADC functionality of Texas
+ Instruments TSC2046 touch screen controller.
+
+ This driver can also be built as a module. If so, the module will be
+ called ti-tsc2046.
+
config TWL4030_MADC
tristate "TWL4030 MADC (Monitoring A/D Converter)"
depends on TWL4030_CORE
@@ -106,6 +106,7 @@ obj-$(CONFIG_TI_ADS124S08) += ti-ads124s08.o
obj-$(CONFIG_TI_ADS131E08) += ti-ads131e08.o
obj-$(CONFIG_TI_AM335X_ADC) += ti_am335x_adc.o
obj-$(CONFIG_TI_TLC4541) += ti-tlc4541.o
+obj-$(CONFIG_TI_TSC2046) += ti-tsc2046.o
obj-$(CONFIG_TWL4030_MADC) += twl4030-madc.o
obj-$(CONFIG_TWL6030_GPADC) += twl6030-gpadc.o
obj-$(CONFIG_VF610_ADC) += vf610_adc.o
new file mode 100644
@@ -0,0 +1,726 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Texas Instruments TSC2046 SPI ADC driver
+ *
+ * Copyright (c) 2021 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+#include <linux/bitfield.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/spi/spi.h>
+
+#include <asm/unaligned.h>
+
+#include <linux/iio/buffer.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/iio/trigger.h>
+
+/*
+ * The PENIRQ of TSC2046 controller is implemented as level shifter attached to
+ * the X+ line. If voltage of the X+ line reaches a specific level the IRQ will
+ * be activated or deactivated.
+ * To make this kind of IRQ reusable as trigger following additions were
+ * implemented:
+ * - rate limiting:
+ * For typical touchscreen use case, we need to trigger about each 10ms.
+ * - hrtimer:
+ * Continue triggering at least once after the IRQ was deactivated. Then
+ * deactivate this trigger to stop sampling in order to reduce power
+ * consumption.
+ */
+
+#define TI_TSC2046_NAME "tsc2046"
+
+/* This driver doesn't aim at the peak continuous sample rate */
+#define TI_TSC2046_MAX_SAMPLE_RATE 125000
+#define TI_TSC2046_SAMPLE_BITS \
+ BITS_PER_TYPE(struct tsc2046_adc_atom)
+#define TI_TSC2046_MAX_CLK_FREQ \
+ (TI_TSC2046_MAX_SAMPLE_RATE * TI_TSC2046_SAMPLE_BITS)
+
+#define TI_TSC2046_SAMPLE_INTERVAL_US 10000
+
+#define TI_TSC2046_START BIT(7)
+#define TI_TSC2046_ADDR GENMASK(6, 4)
+#define TI_TSC2046_ADDR_TEMP1 7
+#define TI_TSC2046_ADDR_AUX 6
+#define TI_TSC2046_ADDR_X 5
+#define TI_TSC2046_ADDR_Z2 4
+#define TI_TSC2046_ADDR_Z1 3
+#define TI_TSC2046_ADDR_VBAT 2
+#define TI_TSC2046_ADDR_Y 1
+#define TI_TSC2046_ADDR_TEMP0 0
+
+/*
+ * The mode bit sets the resolution of the ADC. With this bit low, the next
+ * conversion has 12-bit resolution, whereas with this bit high, the next
+ * conversion has 8-bit resolution. This driver is optimized for 12-bit mode.
+ * So, for this driver, this bit should stay zero.
+ */
+#define TI_TSC2046_8BIT_MODE BIT(3)
+
+/*
+ * SER/DFR - The SER/DFR bit controls the reference mode, either single-ended
+ * (high) or differential (low).
+ */
+#define TI_TSC2046_SER BIT(2)
+
+/*
+ * If VREF_ON and ADC_ON are both zero, then the chip operates in
+ * auto-wake/suspend mode. In most case this bits should stay zero.
+ */
+#define TI_TSC2046_PD1_VREF_ON BIT(1)
+#define TI_TSC2046_PD0_ADC_ON BIT(0)
+
+/*
+ * All supported devices can do 8 or 12bit resolution. This driver
+ * supports only 12bit mode, here we have a 16bit data transfer, where
+ * the MSB and the 3 LSB are 0.
+ */
+#define TI_TSC2046_DATA_12BIT GENMASK(14, 3)
+
+#define TI_TSC2046_MAX_CHAN 8
+
+/* Represents a HW sample */
+struct tsc2046_adc_atom {
+ /*
+ * Command transmitted to the controller. This field is empty on the RX
+ * buffer.
+ */
+ u8 cmd;
+ /*
+ * Data received from the controller. This field is empty for the TX
+ * buffer
+ */
+ __be16 data;
+} __packed;
+
+/* Layout of atomic buffers within big buffer */
+struct tsc2046_adc_group_layout {
+ /* Group offset within the SPI RX buffer */
+ unsigned int offset;
+ /*
+ * Amount of tsc2046_adc_atom structs within the same command gathered
+ * within same group.
+ */
+ unsigned int count;
+ /*
+ * Settling samples (tsc2046_adc_atom structs) which should be skipped
+ * before good samples will start.
+ */
+ unsigned int skip;
+};
+
+struct tsc2046_adc_dcfg {
+ const struct iio_chan_spec *channels;
+ unsigned int num_channels;
+};
+
+struct tsc2046_adc_ch_cfg {
+ unsigned int settling_time_us;
+ unsigned int oversampling_ratio;
+};
+
+struct tsc2046_adc_priv {
+ struct spi_device *spi;
+ const struct tsc2046_adc_dcfg *dcfg;
+
+ struct iio_trigger *trig;
+ struct hrtimer trig_timer;
+ spinlock_t trig_lock;
+ unsigned int trig_more_count;
+
+ struct spi_transfer xfer;
+ struct spi_message msg;
+
+ struct {
+ /* Scan data for each channel */
+ u16 data[TI_TSC2046_MAX_CHAN];
+ /* Timestamp */
+ s64 ts __aligned(8);
+ } scan_buf;
+
+ /*
+ * Lock to protect the layout and the SPI transfer buffer.
+ * tsc2046_adc_group_layout can be changed within update_scan_mode(),
+ * in this case the l[] and tx/rx buffer will be out of sync to each
+ * other.
+ */
+ struct mutex slock;
+ struct tsc2046_adc_group_layout l[TI_TSC2046_MAX_CHAN];
+ struct tsc2046_adc_atom *rx;
+ struct tsc2046_adc_atom *tx;
+
+ struct tsc2046_adc_atom *rx_one;
+ struct tsc2046_adc_atom *tx_one;
+
+ unsigned int count;
+ unsigned int groups;
+ u32 effective_speed_hz;
+ u32 scan_interval_us;
+ u32 time_per_scan_us;
+ u32 time_per_bit_ns;
+
+ struct tsc2046_adc_ch_cfg ch_cfg[TI_TSC2046_MAX_CHAN];
+};
+
+#define TI_TSC2046_V_CHAN(index, bits, name) \
+{ \
+ .type = IIO_VOLTAGE, \
+ .indexed = 1, \
+ .channel = index, \
+ .datasheet_name = "#name", \
+ .scan_index = index, \
+ .scan_type = { \
+ .sign = 'u', \
+ .realbits = bits, \
+ .storagebits = 16, \
+ .endianness = IIO_CPU, \
+ }, \
+}
+
+#define DECLARE_TI_TSC2046_8_CHANNELS(name, bits) \
+const struct iio_chan_spec name ## _channels[] = { \
+ TI_TSC2046_V_CHAN(0, bits, TEMP0), \
+ TI_TSC2046_V_CHAN(1, bits, Y), \
+ TI_TSC2046_V_CHAN(2, bits, VBAT), \
+ TI_TSC2046_V_CHAN(3, bits, Z1), \
+ TI_TSC2046_V_CHAN(4, bits, Z2), \
+ TI_TSC2046_V_CHAN(5, bits, X), \
+ TI_TSC2046_V_CHAN(6, bits, AUX), \
+ TI_TSC2046_V_CHAN(7, bits, TEMP1), \
+ IIO_CHAN_SOFT_TIMESTAMP(8), \
+}
+
+static DECLARE_TI_TSC2046_8_CHANNELS(tsc2046_adc, 12);
+
+static const struct tsc2046_adc_dcfg tsc2046_adc_dcfg_tsc2046e = {
+ .channels = tsc2046_adc_channels,
+ .num_channels = ARRAY_SIZE(tsc2046_adc_channels),
+};
+
+/*
+ * Convert time to a number of samples which can be transferred within this
+ * time.
+ */
+static unsigned int tsc2046_adc_time_to_count(struct tsc2046_adc_priv *priv,
+ unsigned long time)
+{
+ unsigned int bit_count, sample_count;
+
+ bit_count = DIV_ROUND_UP(time * NSEC_PER_USEC, priv->time_per_bit_ns);
+ sample_count = DIV_ROUND_UP(bit_count, TI_TSC2046_SAMPLE_BITS);
+
+ dev_dbg(&priv->spi->dev, "Effective speed %u, time per bit: %u, count bits: %u, count samples: %u\n",
+ priv->effective_speed_hz, priv->time_per_bit_ns,
+ bit_count, sample_count);
+
+ return sample_count;
+}
+
+static u8 tsc2046_adc_get_cmd(struct tsc2046_adc_priv *priv, int ch_idx,
+ bool keep_power)
+{
+ u32 pd;
+
+ /*
+ * if PD bits are 0, controller will automatically disable ADC, VREF and
+ * enable IRQ.
+ */
+ if (keep_power)
+ pd = TI_TSC2046_PD0_ADC_ON;
+ else
+ pd = 0;
+
+ return TI_TSC2046_START | FIELD_PREP(TI_TSC2046_ADDR, ch_idx) | pd;
+}
+
+static u16 tsc2046_adc_get_value(struct tsc2046_adc_atom *buf)
+{
+ return FIELD_GET(TI_TSC2046_DATA_12BIT, get_unaligned_be16(&buf->data));
+}
+
+static int tsc2046_adc_read_one(struct tsc2046_adc_priv *priv, int ch_idx,
+ u32 *effective_speed_hz)
+{
+ struct spi_transfer xfer;
+ struct spi_message msg;
+ int ret;
+
+ memset(&xfer, 0, sizeof(xfer));
+ priv->tx_one->cmd = tsc2046_adc_get_cmd(priv, ch_idx, false);
+ priv->tx_one->data = 0;
+ xfer.tx_buf = priv->tx_one;
+ xfer.rx_buf = priv->rx_one;
+ xfer.len = sizeof(*priv->tx_one);
+ spi_message_init(&msg);
+ spi_message_add_tail(&xfer, &msg);
+
+ /*
+ * We aren't using spi_write_then_read() because we need to be able
+ * to get hold of the effective_speed_hz from the xfer
+ */
+ ret = spi_sync(priv->spi, &msg);
+ if (ret) {
+ dev_err_ratelimited(&priv->spi->dev, "SPI transfer failed %pe\n",
+ ERR_PTR(ret));
+ return ret;
+ }
+
+ if (effective_speed_hz)
+ *effective_speed_hz = xfer.effective_speed_hz;
+
+ return tsc2046_adc_get_value(priv->rx_one);
+}
+
+static size_t tsc2046_adc_group_set_layout(struct tsc2046_adc_priv *priv,
+ unsigned int group,
+ unsigned int ch_idx)
+{
+ struct tsc2046_adc_ch_cfg *ch = &priv->ch_cfg[ch_idx];
+ struct tsc2046_adc_group_layout *cur;
+ unsigned int max_count, count_skip;
+ unsigned int offset = 0;
+
+ if (group)
+ offset = priv->l[group - 1].offset + priv->l[group - 1].count;
+
+ count_skip = tsc2046_adc_time_to_count(priv, ch->settling_time_us);
+ max_count = count_skip + ch->oversampling_ratio;
+
+ cur = &priv->l[group];
+ cur->offset = offset;
+ cur->count = max_count;
+ cur->skip = count_skip;
+
+ return sizeof(*priv->tx) * max_count;
+}
+
+static void tsc2046_adc_group_set_cmd(struct tsc2046_adc_priv *priv,
+ unsigned int group, int ch_idx)
+{
+ struct tsc2046_adc_group_layout *l = &priv->l[group];
+ unsigned int i;
+ u8 cmd;
+
+ /*
+ * Do not enable automatic power down on working samples. Otherwise the
+ * plates will never be completely charged.
+ */
+ cmd = tsc2046_adc_get_cmd(priv, ch_idx, true);
+
+ for (i = 0; i < l->count - 1; i++)
+ priv->tx[l->offset + i].cmd = cmd;
+
+ /* automatically power down on last sample */
+ priv->tx[l->offset + i].cmd = tsc2046_adc_get_cmd(priv, ch_idx, false);
+}
+
+static u16 tsc2046_adc_get_val(struct tsc2046_adc_priv *priv, int group)
+{
+ struct tsc2046_adc_group_layout *l;
+ unsigned int val, val_normalized = 0;
+ int valid_count, i;
+
+ l = &priv->l[group];
+ valid_count = l->count - l->skip;
+
+ for (i = 0; i < valid_count; i++) {
+ val = tsc2046_adc_get_value(&priv->rx[l->offset + l->skip + i]);
+ val_normalized += val;
+ }
+
+ return DIV_ROUND_UP(val_normalized, valid_count);
+}
+
+static int tsc2046_adc_scan(struct iio_dev *indio_dev)
+{
+ struct tsc2046_adc_priv *priv = iio_priv(indio_dev);
+ struct device *dev = &priv->spi->dev;
+ int group;
+ int ret;
+
+ ret = spi_sync(priv->spi, &priv->msg);
+ if (ret < 0) {
+ dev_err_ratelimited(dev, "SPI transfer failed: %pe\n", ERR_PTR(ret));
+ return ret;
+ }
+
+ for (group = 0; group < priv->groups; group++)
+ priv->scan_buf.data[group] = tsc2046_adc_get_val(priv, group);
+
+ ret = iio_push_to_buffers_with_timestamp(indio_dev, &priv->scan_buf,
+ iio_get_time_ns(indio_dev));
+ /* If the consumer is kfifo, we may get a EBUSY here - ignore it. */
+ if (ret < 0 && ret != -EBUSY) {
+ dev_err_ratelimited(dev, "Failed to push scan buffer %pe\n",
+ ERR_PTR(ret));
+
+ return ret;
+ }
+
+ return 0;
+}
+
+static irqreturn_t tsc2046_adc_trigger_handler(int irq, void *p)
+{
+ struct iio_poll_func *pf = p;
+ struct iio_dev *indio_dev = pf->indio_dev;
+ struct tsc2046_adc_priv *priv = iio_priv(indio_dev);
+
+ mutex_lock(&priv->slock);
+ tsc2046_adc_scan(indio_dev);
+ mutex_unlock(&priv->slock);
+
+ iio_trigger_notify_done(indio_dev->trig);
+
+ return IRQ_HANDLED;
+}
+
+static int tsc2046_adc_update_scan_mode(struct iio_dev *indio_dev,
+ const unsigned long *active_scan_mask)
+{
+ struct tsc2046_adc_priv *priv = iio_priv(indio_dev);
+ unsigned int ch_idx, group = 0;
+ size_t size;
+
+ mutex_lock(&priv->slock);
+
+ size = 0;
+ for_each_set_bit(ch_idx, active_scan_mask, indio_dev->num_channels) {
+ size += tsc2046_adc_group_set_layout(priv, group, ch_idx);
+ tsc2046_adc_group_set_cmd(priv, group, ch_idx);
+ group++;
+ }
+
+ priv->groups = group;
+ priv->xfer.len = size;
+ priv->time_per_scan_us = size * 8 * priv->time_per_bit_ns / NSEC_PER_USEC;
+
+ if ((priv->scan_interval_us - priv->time_per_scan_us) < 0)
+ dev_warn(&priv->spi->dev, "The scan interval (%d) is less then calculated scan time (%d)\n",
+ priv->scan_interval_us, priv->time_per_scan_us);
+
+ mutex_unlock(&priv->slock);
+
+ return 0;
+}
+
+static const struct iio_info tsc2046_adc_info = {
+ .update_scan_mode = tsc2046_adc_update_scan_mode,
+};
+
+static enum hrtimer_restart tsc2046_adc_trig_more(struct hrtimer *hrtimer)
+{
+ struct tsc2046_adc_priv *priv = container_of(hrtimer,
+ struct tsc2046_adc_priv,
+ trig_timer);
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv->trig_lock, flags);
+
+ disable_irq_nosync(priv->spi->irq);
+
+ priv->trig_more_count++;
+ iio_trigger_poll(priv->trig);
+
+ spin_unlock_irqrestore(&priv->trig_lock, flags);
+
+ return HRTIMER_NORESTART;
+}
+
+static irqreturn_t tsc2046_adc_irq(int irq, void *dev_id)
+{
+ struct iio_dev *indio_dev = dev_id;
+ struct tsc2046_adc_priv *priv = iio_priv(indio_dev);
+
+ spin_lock(&priv->trig_lock);
+
+ hrtimer_try_to_cancel(&priv->trig_timer);
+
+ priv->trig_more_count = 0;
+ disable_irq_nosync(priv->spi->irq);
+ iio_trigger_poll(priv->trig);
+
+ spin_unlock(&priv->trig_lock);
+
+ return IRQ_HANDLED;
+}
+
+static void tsc2046_adc_reenable_trigger(struct iio_trigger *trig)
+{
+ struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig);
+ struct tsc2046_adc_priv *priv = iio_priv(indio_dev);
+ unsigned long flags;
+ int delta;
+
+ /*
+ * We can sample it as fast as we can, but usually we do not need so
+ * many samples. Reduce the sample rate for default (touchscreen) use
+ * case.
+ * Currently we do not need a highly precise sample rate. It is enough
+ * to have calculated numbers.
+ */
+ delta = priv->scan_interval_us - priv->time_per_scan_us;
+ if (delta > 0)
+ fsleep(delta);
+
+ spin_lock_irqsave(&priv->trig_lock, flags);
+
+ /*
+ * We need to trigger at least one extra sample to detect state
+ * difference on ADC side.
+ */
+ if (!priv->trig_more_count) {
+ int timeout_ms = DIV_ROUND_UP(priv->scan_interval_us,
+ USEC_PER_MSEC);
+
+ hrtimer_start(&priv->trig_timer, ms_to_ktime(timeout_ms),
+ HRTIMER_MODE_REL_SOFT);
+ }
+
+ enable_irq(priv->spi->irq);
+
+ spin_unlock_irqrestore(&priv->trig_lock, flags);
+}
+
+static int tsc2046_adc_set_trigger_state(struct iio_trigger *trig, bool enable)
+{
+ struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig);
+ struct tsc2046_adc_priv *priv = iio_priv(indio_dev);
+
+ if (enable) {
+ enable_irq(priv->spi->irq);
+ } else {
+ disable_irq(priv->spi->irq);
+ hrtimer_try_to_cancel(&priv->trig_timer);
+ }
+
+ return 0;
+}
+
+static const struct iio_trigger_ops tsc2046_adc_trigger_ops = {
+ .set_trigger_state = tsc2046_adc_set_trigger_state,
+ .reenable = tsc2046_adc_reenable_trigger,
+};
+
+static int tsc2046_adc_setup_spi_msg(struct tsc2046_adc_priv *priv)
+{
+ unsigned int ch_idx;
+ size_t size;
+ int ret;
+
+ priv->tx_one = devm_kzalloc(&priv->spi->dev, sizeof(*priv->tx_one),
+ GFP_KERNEL);
+ if (!priv->tx_one)
+ return -ENOMEM;
+
+ priv->rx_one = devm_kzalloc(&priv->spi->dev, sizeof(*priv->rx_one),
+ GFP_KERNEL);
+ if (!priv->rx_one)
+ return -ENOMEM;
+
+ /*
+ * Make dummy read to set initial power state and get real SPI clock
+ * freq. It seems to be not important which channel is used for this
+ * case.
+ */
+ ret = tsc2046_adc_read_one(priv, TI_TSC2046_ADDR_TEMP0,
+ &priv->effective_speed_hz);
+ if (ret < 0)
+ return ret;
+
+ /*
+ * In case SPI controller do not report effective_speed_hz, use
+ * configure value and hope it will match.
+ */
+ if (!priv->effective_speed_hz)
+ priv->effective_speed_hz = priv->spi->max_speed_hz;
+
+
+ priv->scan_interval_us = TI_TSC2046_SAMPLE_INTERVAL_US;
+ priv->time_per_bit_ns = DIV_ROUND_UP(NSEC_PER_SEC,
+ priv->effective_speed_hz);
+
+ /*
+ * Calculate and allocate maximal size buffer if all channels are
+ * enabled.
+ */
+ size = 0;
+ for (ch_idx = 0; ch_idx < priv->dcfg->num_channels; ch_idx++)
+ size += tsc2046_adc_group_set_layout(priv, ch_idx, ch_idx);
+
+ priv->tx = devm_kzalloc(&priv->spi->dev, size, GFP_KERNEL);
+ if (!priv->tx)
+ return -ENOMEM;
+
+ priv->rx = devm_kzalloc(&priv->spi->dev, size, GFP_KERNEL);
+ if (!priv->rx)
+ return -ENOMEM;
+
+ spi_message_init(&priv->msg);
+ priv->msg.context = priv;
+
+ priv->xfer.tx_buf = priv->tx;
+ priv->xfer.rx_buf = priv->rx;
+ priv->xfer.len = size;
+ spi_message_add_tail(&priv->xfer, &priv->msg);
+
+ return 0;
+}
+
+static void tsc2046_adc_parse_fwnode(struct tsc2046_adc_priv *priv)
+{
+ struct fwnode_handle *child;
+ struct device *dev = &priv->spi->dev;
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(priv->ch_cfg); i++) {
+ priv->ch_cfg[i].settling_time_us = 1;
+ priv->ch_cfg[i].oversampling_ratio = 1;
+ }
+
+ device_for_each_child_node(dev, child) {
+ u32 stl, overs, reg;
+ int ret;
+
+ ret = fwnode_property_read_u32(child, "reg", ®);
+ if (ret) {
+ dev_err(dev, "invalid reg on %pfw, err: %pe\n", child,
+ ERR_PTR(ret));
+ continue;
+ }
+
+ if (reg >= ARRAY_SIZE(priv->ch_cfg)) {
+ dev_err(dev, "%pfw: Unsupported reg value: %i, max supported is: %zu.\n",
+ child, reg, ARRAY_SIZE(priv->ch_cfg));
+ continue;
+ }
+
+ ret = fwnode_property_read_u32(child, "settling-time-us", &stl);
+ if (!ret)
+ priv->ch_cfg[reg].settling_time_us = stl;
+
+ ret = fwnode_property_read_u32(child, "oversampling-ratio",
+ &overs);
+ if (!ret)
+ priv->ch_cfg[reg].oversampling_ratio = overs;
+ }
+}
+
+static int tsc2046_adc_probe(struct spi_device *spi)
+{
+ const struct tsc2046_adc_dcfg *dcfg;
+ struct device *dev = &spi->dev;
+ struct tsc2046_adc_priv *priv;
+ struct iio_dev *indio_dev;
+ struct iio_trigger *trig;
+ const char *name;
+ int ret;
+
+ if (spi->max_speed_hz > TI_TSC2046_MAX_CLK_FREQ) {
+ dev_err(dev, "SPI max_speed_hz is too high: %d Hz. Max supported freq is %zu Hz\n",
+ spi->max_speed_hz, TI_TSC2046_MAX_CLK_FREQ);
+ return -EINVAL;
+ }
+
+ dcfg = device_get_match_data(dev);
+ if (!dcfg)
+ return -EINVAL;
+
+ spi->bits_per_word = 8;
+ spi->mode &= ~SPI_MODE_X_MASK;
+ spi->mode |= SPI_MODE_0;
+ ret = spi_setup(spi);
+ if (ret < 0)
+ return dev_err_probe(dev, ret, "Error in SPI setup\n");
+
+ indio_dev = devm_iio_device_alloc(dev, sizeof(*priv));
+ if (!indio_dev)
+ return -ENOMEM;
+
+ priv = iio_priv(indio_dev);
+ priv->dcfg = dcfg;
+
+ spi_set_drvdata(spi, indio_dev);
+
+ priv->spi = spi;
+
+ name = devm_kasprintf(dev, GFP_KERNEL, "%s-%s",
+ TI_TSC2046_NAME, dev_name(dev));
+ if (!name)
+ return -ENOMEM;
+
+ indio_dev->name = name;
+ indio_dev->modes = INDIO_DIRECT_MODE | INDIO_BUFFER_TRIGGERED;
+ indio_dev->channels = dcfg->channels;
+ indio_dev->num_channels = dcfg->num_channels;
+ indio_dev->info = &tsc2046_adc_info;
+
+ tsc2046_adc_parse_fwnode(priv);
+
+ ret = tsc2046_adc_setup_spi_msg(priv);
+ if (ret)
+ return ret;
+
+ mutex_init(&priv->slock);
+
+ /* TODO: remove IRQ_NOAUTOEN after needed patches are mainline */
+ irq_set_status_flags(spi->irq, IRQ_NOAUTOEN);
+ ret = devm_request_irq(dev, spi->irq, &tsc2046_adc_irq,
+ 0, name, indio_dev);
+ if (ret)
+ return ret;
+
+ trig = devm_iio_trigger_alloc(dev, "touchscreen-%s", indio_dev->name);
+ if (!trig)
+ return -ENOMEM;
+
+ priv->trig = trig;
+ iio_trigger_set_drvdata(trig, indio_dev);
+ trig->ops = &tsc2046_adc_trigger_ops;
+
+ spin_lock_init(&priv->trig_lock);
+ hrtimer_init(&priv->trig_timer, CLOCK_MONOTONIC,
+ HRTIMER_MODE_REL_SOFT);
+ priv->trig_timer.function = tsc2046_adc_trig_more;
+
+ ret = devm_iio_trigger_register(dev, trig);
+ if (ret) {
+ dev_err(dev, "failed to register trigger\n");
+ return ret;
+ }
+
+ ret = devm_iio_triggered_buffer_setup(dev, indio_dev, NULL,
+ &tsc2046_adc_trigger_handler, NULL);
+ if (ret) {
+ dev_err(dev, "Failed to setup triggered buffer\n");
+ return ret;
+ }
+
+ /* set default trigger */
+ indio_dev->trig = iio_trigger_get(priv->trig);
+
+ return devm_iio_device_register(dev, indio_dev);
+}
+
+static const struct of_device_id ads7950_of_table[] = {
+ { .compatible = "ti,tsc2046e-adc", .data = &tsc2046_adc_dcfg_tsc2046e },
+ { }
+};
+MODULE_DEVICE_TABLE(of, ads7950_of_table);
+
+static struct spi_driver tsc2046_adc_driver = {
+ .driver = {
+ .name = "tsc2046",
+ .of_match_table = ads7950_of_table,
+ },
+ .probe = tsc2046_adc_probe,
+};
+module_spi_driver(tsc2046_adc_driver);
+
+MODULE_AUTHOR("Oleksij Rempel <kernel@pengutronix.de>");
+MODULE_DESCRIPTION("TI TSC2046 ADC");
+MODULE_LICENSE("GPL v2");