new file mode 100644
@@ -0,0 +1,150 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/resolver/adi,ad2s1210.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices AD2S1210 Resolver-to-Digital Converter
+
+maintainers:
+ - Michael Hennerich <michael.hennerich@analog.com>
+
+description: |
+ The AD2S1210 is a complete 10-bit to 16-bit resolution tracking
+ resolver-to-digital converter, integrating an on-board programmable
+ sinusoidal oscillator that provides sine wave excitation for
+ resolvers.
+
+ The AD2S1210 allows the user to read the angular position or the
+ angular velocity data directly from the parallel outputs or through
+ the serial interface.
+
+ A1 A0 Result
+ 0 0 Normal mode - position output
+ 0 1 Normal mode - velocity output
+ 1 0 Reserved
+ 1 1 Configuration mode
+
+ In normal mode, the resolution of the digital output is selected using
+ the RES0 and RES1 input pins. In configuration mode, the resolution is
+ selected by setting the RES0 and RES1 bits in the control register.
+
+ RES1 RES0 Resolution (Bits)
+ 0 0 10
+ 0 1 12
+ 1 0 14
+ 1 1 16
+
+ Note on SPI connections: The CS line on the AD2S1210 should hard-wired to
+ logic low and the WR/FSYNC line on the AD2S1210 should be connected to the
+ SPI CSn output of the SPI controller.
+
+ Datasheet:
+ https://www.analog.com/media/en/technical-documentation/data-sheets/ad2s1210.pdf
+
+properties:
+ compatible:
+ const: adi,ad2s1210
+
+ reg:
+ maxItems: 1
+
+ spi-max-frequency:
+ maximum: 25000000
+
+ spi-cpha: true
+
+ clocks:
+ maxItems: 1
+ description: External oscillator clock (CLKIN).
+
+ reset-gpios:
+ description:
+ GPIO connected to the /RESET pin. As the line needs to be low for the
+ reset to be active, it should be configured as GPIO_ACTIVE_LOW.
+ maxItems: 1
+
+ sample-gpios:
+ description:
+ GPIO connected to the /SAMPLE pin. As the line needs to be low to trigger
+ a sample, it should be configured as GPIO_ACTIVE_LOW.
+ maxItems: 1
+
+ mode-gpios:
+ description:
+ GPIO lines connected to the A0 and A1 pins. These pins select the data
+ transfer mode.
+ minItems: 2
+ maxItems: 2
+
+ resolution-gpios:
+ description:
+ GPIO lines connected to the RES0 and RES1 pins. These pins select the
+ resolution of the digital output. If omitted, it is assumed that the
+ RES0 and RES1 pins are hard-wired to match the assigned-resolution-bits
+ property.
+ minItems: 2
+ maxItems: 2
+
+ fault-gpios:
+ description:
+ GPIO lines connected to the LOT and DOS pins. These pins combined indicate
+ the type of fault present, if any. As these pins a pulled low to indicate
+ a fault condition, they should be configured as GPIO_ACTIVE_LOW.
+ minItems: 2
+ maxItems: 2
+
+ adi,fixed-mode:
+ description:
+ This is used to indicate the selected mode if A0 and A1 are hard-wired
+ instead of connected to GPIOS (i.e. mode-gpios is omitted).
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [config, velocity, position]
+
+ assigned-resolution-bits:
+ description:
+ Resolution of the digital output required by the application. This
+ determines the precision of the angle and/or the maximum speed that can
+ be measured. If resolution-gpios is omitted, it is assumed that RES0 and
+ RES1 are hard-wired to match this value.
+ enum: [10, 12, 14, 16]
+
+required:
+ - compatible
+ - reg
+ - spi-cpha
+ - clocks
+ - sample-gpios
+ - assigned-resolution-bits
+
+oneOf:
+ - required:
+ - mode-gpios
+ - required:
+ - adi,fixed-mode
+
+allOf:
+ - $ref: /schemas/spi/spi-peripheral-props.yaml#
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ resolver@0 {
+ compatible = "adi,ad2s1210";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ spi-cpha;
+ clocks = <&ext_osc>;
+ sample-gpios = <&gpio0 90 GPIO_ACTIVE_LOW>;
+ mode-gpios = <&gpio0 86 0>, <&gpio0 87 0>;
+ resolution-gpios = <&gpio0 88 0>, <&gpio0 89 0>;
+ assigned-resolution-bits = <16>;
+ };
+ };