@@ -32,12 +32,12 @@
* Scales are computed as 5000/32768 and 10000/32768 respectively,
* so that when applied to the raw values they provide mV values
*/
-static const unsigned int ad7606_scale_avail[2] = {
+static const unsigned int ad7606_16bit_hw_scale_avail[2] = {
152588, 305176
};
-static const unsigned int ad7616_sw_scale_avail[3] = {
+static const unsigned int ad7606_16bit_sw_scale_avail[3] = {
76293, 152588, 305176
};
@@ -62,6 +62,25 @@ int ad7606_reset(struct ad7606_state *st)
}
EXPORT_SYMBOL_NS_GPL(ad7606_reset, IIO_AD7606);
+static int ad7606_16bit_chan_scale_setup(struct ad7606_state *st, int ch)
+{
+ if (!st->sw_mode_en) {
+ /* tied to logic low, analog input range is +/- 5V */
+ st->range[ch] = 0;
+ st->scale_avail = ad7606_16bit_hw_scale_avail;
+ st->num_scales = ARRAY_SIZE(ad7606_16bit_hw_scale_avail);
+ return 0;
+ }
+
+ /* Scale of 0.076293 is only available in sw mode */
+ /* After reset, in software mode, ±10 V is set by default */
+ st->range[ch] = 2;
+ st->scale_avail = ad7606_16bit_sw_scale_avail;
+ st->num_scales = ARRAY_SIZE(ad7606_16bit_sw_scale_avail);
+
+ return 0;
+}
+
static int ad7606_reg_access(struct iio_dev *indio_dev,
unsigned int reg,
unsigned int writeval,
@@ -358,34 +377,40 @@ static const struct ad7606_chip_info ad7606_chip_info_tbl[] = {
[ID_AD7605_4] = {
.channels = ad7605_channels,
.num_channels = 5,
+ .scale_setup_cb = ad7606_16bit_chan_scale_setup,
},
[ID_AD7606_8] = {
.channels = ad7606_channels_16bit,
.num_channels = 9,
+ .scale_setup_cb = ad7606_16bit_chan_scale_setup,
.oversampling_avail = ad7606_oversampling_avail,
.oversampling_num = ARRAY_SIZE(ad7606_oversampling_avail),
},
[ID_AD7606_6] = {
.channels = ad7606_channels_16bit,
.num_channels = 7,
+ .scale_setup_cb = ad7606_16bit_chan_scale_setup,
.oversampling_avail = ad7606_oversampling_avail,
.oversampling_num = ARRAY_SIZE(ad7606_oversampling_avail),
},
[ID_AD7606_4] = {
.channels = ad7606_channels_16bit,
.num_channels = 5,
+ .scale_setup_cb = ad7606_16bit_chan_scale_setup,
.oversampling_avail = ad7606_oversampling_avail,
.oversampling_num = ARRAY_SIZE(ad7606_oversampling_avail),
},
[ID_AD7606B] = {
.channels = ad7606_channels_16bit,
.num_channels = 9,
+ .scale_setup_cb = ad7606_16bit_chan_scale_setup,
.oversampling_avail = ad7606_oversampling_avail,
.oversampling_num = ARRAY_SIZE(ad7606_oversampling_avail),
},
[ID_AD7616] = {
.channels = ad7616_channels,
.num_channels = 17,
+ .scale_setup_cb = ad7606_16bit_chan_scale_setup,
.oversampling_avail = ad7616_oversampling_avail,
.oversampling_num = ARRAY_SIZE(ad7616_oversampling_avail),
.os_req_reset = true,
@@ -523,6 +548,35 @@ static const struct iio_trigger_ops ad7606_trigger_ops = {
.validate_device = iio_trigger_validate_own_device,
};
+static int ad7606_sw_mode_setup(struct iio_dev *indio_dev)
+{
+ struct ad7606_state *st = iio_priv(indio_dev);
+
+ st->sw_mode_en = st->bops->sw_mode_config &&
+ device_property_present(st->dev, "adi,sw-mode");
+ if (!st->sw_mode_en)
+ return 0;
+
+ indio_dev->info = &ad7606_info_os_range_and_debug;
+
+ return st->bops->sw_mode_config(indio_dev);
+}
+
+static int ad7606_chan_scales_setup(struct iio_dev *indio_dev)
+{
+ unsigned int num_channels = indio_dev->num_channels - 1;
+ struct ad7606_state *st = iio_priv(indio_dev);
+ int ch, ret;
+
+ for (ch = 0; ch < num_channels; ch++) {
+ ret = st->chip_info->scale_setup_cb(st, ch);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
int ad7606_probe(struct device *dev, int irq, void __iomem *base_address,
const char *name, unsigned int id,
const struct ad7606_bus_ops *bops)
@@ -542,11 +596,7 @@ int ad7606_probe(struct device *dev, int irq, void __iomem *base_address,
mutex_init(&st->lock);
st->bops = bops;
st->base_address = base_address;
- /* tied to logic low, analog input range is +/- 5V */
- st->range[0] = 0;
st->oversampling = 1;
- st->scale_avail = ad7606_scale_avail;
- st->num_scales = ARRAY_SIZE(ad7606_scale_avail);
ret = devm_regulator_get_enable(dev, "avcc");
if (ret)
@@ -595,23 +645,13 @@ int ad7606_probe(struct device *dev, int irq, void __iomem *base_address,
st->write_scale = ad7606_write_scale_hw;
st->write_os = ad7606_write_os_hw;
- if (st->bops->sw_mode_config)
- st->sw_mode_en = device_property_present(st->dev,
- "adi,sw-mode");
-
- if (st->sw_mode_en) {
- /* Scale of 0.076293 is only available in sw mode */
- st->scale_avail = ad7616_sw_scale_avail;
- st->num_scales = ARRAY_SIZE(ad7616_sw_scale_avail);
-
- /* After reset, in software mode, ±10 V is set by default */
- memset32(st->range, 2, ARRAY_SIZE(st->range));
- indio_dev->info = &ad7606_info_os_range_and_debug;
+ ret = ad7606_sw_mode_setup(indio_dev);
+ if (ret)
+ return ret;
- ret = st->bops->sw_mode_config(indio_dev);
- if (ret < 0)
- return ret;
- }
+ ret = ad7606_chan_scales_setup(indio_dev);
+ if (ret)
+ return ret;
st->trig = devm_iio_trigger_alloc(dev, "%s-dev%d",
indio_dev->name,
@@ -40,10 +40,15 @@
#define AD7616_CHANNEL(num) AD7606_SW_CHANNEL(num, 16)
+struct ad7606_state;
+
+typedef int (*ad7606_scale_setup_cb_t)(struct ad7606_state *st, int ch);
+
/**
* struct ad7606_chip_info - chip specific information
* @channels: channel specification
* @num_channels: number of channels
+ * @scale_setup_cb: callback to setup the scales for each channel
* @oversampling_avail pointer to the array which stores the available
* oversampling ratios.
* @oversampling_num number of elements stored in oversampling_avail array
@@ -54,6 +59,7 @@
struct ad7606_chip_info {
const struct iio_chan_spec *channels;
unsigned int num_channels;
+ ad7606_scale_setup_cb_t scale_setup_cb;
const unsigned int *oversampling_avail;
unsigned int oversampling_num;
bool os_req_reset;
Up until now, all ADCs were 16-bit precision. With the addition of the AD7606C some things will change. For one thing, we'll need to setup available-scales for each channel. Also for the 18-bit precision variants, the scales will be different. This change adds a function-pointer to the chip-info struct to be able to set this up (differently) for the new parts. For the current parts, the scales are the same (for all parts) between HW and SW modes. Also creating a 'ad7606_sw_mode_setup()' function that must be called before the scale_setup callback. This is needed in case SW mode is enabled for some ADCs. Signed-off-by: Alexandru Ardelean <aardelean@baylibre.com> --- drivers/iio/adc/ad7606.c | 84 +++++++++++++++++++++++++++++----------- drivers/iio/adc/ad7606.h | 6 +++ 2 files changed, 68 insertions(+), 22 deletions(-)