@@ -47,6 +47,18 @@ config AD7091R5
help
Say yes here to build support for Analog Devices AD7091R-5 ADC.
+config AD7091R8
+ tristate "Analog Devices AD7091R8 ADC Driver"
+ depends on SPI
+ select AD7091R
+ select REGMAP_SPI
+ help
+ Say yes here to build support for Analog Devices AD7091R-2, AD7091R-4,
+ and AD7091R-8 ADC.
+
+ To compile this driver as a module, choose M here: the module will be
+ called ad7091r8.
+
config AD7124
tristate "Analog Devices AD7124 and similar sigma-delta ADCs driver"
depends on SPI_MASTER
@@ -9,6 +9,7 @@ obj-$(CONFIG_AD_SIGMA_DELTA) += ad_sigma_delta.o
obj-$(CONFIG_AD4130) += ad4130.o
obj-$(CONFIG_AD7091R) += ad7091r-base.o
obj-$(CONFIG_AD7091R5) += ad7091r5.o
+obj-$(CONFIG_AD7091R8) += ad7091r8.o
obj-$(CONFIG_AD7124) += ad7124.o
obj-$(CONFIG_AD7192) += ad7192.o
obj-$(CONFIG_AD7266) += ad7266.o
@@ -6,6 +6,7 @@
*/
#include <linux/bitops.h>
+#include <linux/bitfield.h>
#include <linux/iio/events.h>
#include <linux/iio/iio.h>
#include <linux/interrupt.h>
@@ -187,6 +188,12 @@ int ad7091r_probe(struct device *dev, const struct ad7091r_init_info *init_info,
iio_dev->info = &ad7091r_info;
iio_dev->modes = INDIO_DIRECT_MODE;
+ if (init_info->setup) {
+ ret = init_info->setup(st);
+ if (ret < 0)
+ return ret;
+ }
+
if (irq) {
st->chip_info = &init_info->irq_info;
ret = regmap_update_bits(st->map, AD7091R_REG_CONF,
@@ -45,6 +45,8 @@
.scan_type.realbits = bits, \
}
+#include <linux/gpio/consumer.h>
+
struct device;
enum ad7091r_mode {
@@ -56,10 +58,14 @@ enum ad7091r_mode {
struct ad7091r_state {
struct device *dev;
struct regmap *map;
+ struct gpio_desc *convst_gpio;
+ struct gpio_desc *reset_gpio;
struct regulator *vref;
const struct ad7091r_chip_info *chip_info;
enum ad7091r_mode mode;
struct mutex lock; /*lock to prevent concurent reads */
+ __be16 tx_buf __aligned(IIO_DMA_MINALIGN);
+ __be16 rx_buf;
};
struct ad7091r_chip_info {
@@ -77,6 +83,7 @@ struct ad7091r_init_info {
const struct regmap_config *regmap_config;
void (*init_adc_regmap)(struct ad7091r_state *st,
const struct regmap_config *regmap_conf);
+ int (*setup)(struct ad7091r_state *st);
};
extern const struct iio_event_spec ad7091r_events[3];
new file mode 100644
@@ -0,0 +1,257 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Analog Devices AD7091R8 12-bit SAR ADC driver
+ *
+ * Copyright 2023 Analog Devices Inc.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/iio/iio.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/gpio/consumer.h>
+#include <linux/spi/spi.h>
+
+#include "ad7091r-base.h"
+
+#define AD7091R8_REG_ADDR_MSK GENMASK(15, 11)
+#define AD7091R8_RD_WR_FLAG_MSK BIT(10)
+#define AD7091R8_REG_DATA_MSK GENMASK(9, 0)
+
+#define AD7091R_SPI_REGMAP_CONFIG(n) { \
+ .reg_bits = 8, \
+ .val_bits = 16, \
+ .volatile_reg = ad7091r_volatile_reg, \
+ .writeable_reg = ad7091r_writeable_reg, \
+ .max_register = AD7091R_REG_CH_HYSTERESIS(n), \
+}
+
+#define AD7091R_SPI_CHIP_INFO(_n, _name) { \
+ .name = _name, \
+ .channels = ad7091r##_n##_channels, \
+ .num_channels = ARRAY_SIZE(ad7091r##_n##_channels), \
+ .vref_mV = 2500, \
+ .reg_result_chan_id = &ad7091r8_reg_result_chan_id, \
+ .set_mode = &ad7091r8_set_mode, \
+}
+
+#define AD7091R_SPI_CHIP_INFO_IRQ(_n, _name) { \
+ .name = _name, \
+ .channels = ad7091r##_n##_channels_irq, \
+ .num_channels = ARRAY_SIZE(ad7091r##_n##_channels_irq), \
+ .vref_mV = 2500, \
+ .reg_result_chan_id = &ad7091r8_reg_result_chan_id, \
+ .set_mode = &ad7091r8_set_mode, \
+}
+
+static const struct iio_chan_spec ad7091r2_channels[] = {
+ AD7091R_CHANNEL(0, 12, NULL, 0),
+ AD7091R_CHANNEL(1, 12, NULL, 0),
+};
+
+static const struct iio_chan_spec ad7091r4_channels[] = {
+ AD7091R_CHANNEL(0, 12, NULL, 0),
+ AD7091R_CHANNEL(1, 12, NULL, 0),
+ AD7091R_CHANNEL(2, 12, NULL, 0),
+ AD7091R_CHANNEL(3, 12, NULL, 0),
+};
+
+static const struct iio_chan_spec ad7091r4_channels_irq[] = {
+ AD7091R_CHANNEL(0, 12, ad7091r_events, ARRAY_SIZE(ad7091r_events)),
+ AD7091R_CHANNEL(1, 12, ad7091r_events, ARRAY_SIZE(ad7091r_events)),
+ AD7091R_CHANNEL(2, 12, ad7091r_events, ARRAY_SIZE(ad7091r_events)),
+ AD7091R_CHANNEL(3, 12, ad7091r_events, ARRAY_SIZE(ad7091r_events)),
+};
+
+static const struct iio_chan_spec ad7091r8_channels[] = {
+ AD7091R_CHANNEL(0, 12, NULL, 0),
+ AD7091R_CHANNEL(1, 12, NULL, 0),
+ AD7091R_CHANNEL(2, 12, NULL, 0),
+ AD7091R_CHANNEL(3, 12, NULL, 0),
+ AD7091R_CHANNEL(4, 12, NULL, 0),
+ AD7091R_CHANNEL(5, 12, NULL, 0),
+ AD7091R_CHANNEL(6, 12, NULL, 0),
+ AD7091R_CHANNEL(7, 12, NULL, 0),
+};
+
+static const struct iio_chan_spec ad7091r8_channels_irq[] = {
+ AD7091R_CHANNEL(0, 12, ad7091r_events, ARRAY_SIZE(ad7091r_events)),
+ AD7091R_CHANNEL(1, 12, ad7091r_events, ARRAY_SIZE(ad7091r_events)),
+ AD7091R_CHANNEL(2, 12, ad7091r_events, ARRAY_SIZE(ad7091r_events)),
+ AD7091R_CHANNEL(3, 12, ad7091r_events, ARRAY_SIZE(ad7091r_events)),
+ AD7091R_CHANNEL(4, 12, ad7091r_events, ARRAY_SIZE(ad7091r_events)),
+ AD7091R_CHANNEL(5, 12, ad7091r_events, ARRAY_SIZE(ad7091r_events)),
+ AD7091R_CHANNEL(6, 12, ad7091r_events, ARRAY_SIZE(ad7091r_events)),
+ AD7091R_CHANNEL(7, 12, ad7091r_events, ARRAY_SIZE(ad7091r_events)),
+};
+
+static void ad7091r_pulse_convst(struct ad7091r_state *st)
+{
+ gpiod_set_value_cansleep(st->convst_gpio, 1);
+ gpiod_set_value_cansleep(st->convst_gpio, 0);
+}
+
+static int ad7091r_regmap_bus_reg_read(void *context, unsigned int reg,
+ unsigned int *val)
+{
+ struct ad7091r_state *st = context;
+ struct spi_device *spi = container_of(st->dev, struct spi_device, dev);
+ int ret;
+
+ struct spi_transfer t[] = {
+ {
+ .tx_buf = &st->tx_buf,
+ .len = 2,
+ .cs_change = 1,
+ }, {
+ .rx_buf = &st->rx_buf,
+ .len = 2,
+ }
+ };
+
+ if (reg == AD7091R_REG_RESULT)
+ ad7091r_pulse_convst(st);
+
+ st->tx_buf = cpu_to_be16(reg << 11);
+
+ ret = spi_sync_transfer(spi, t, ARRAY_SIZE(t));
+ if (ret < 0)
+ return ret;
+
+ *val = be16_to_cpu(st->rx_buf);
+ return 0;
+}
+
+static int ad7091r_regmap_bus_reg_write(void *context, unsigned int reg,
+ unsigned int val)
+{
+ struct ad7091r_state *st = context;
+ struct spi_device *spi = container_of(st->dev, struct spi_device, dev);
+
+ /*
+ * AD7091R-2/-4/-8 protocol (datasheet page 31) is to do a single SPI
+ * transfer with reg address set in bits B15:B11 and value set in B9:B0.
+ */
+ st->tx_buf = cpu_to_be16(FIELD_PREP(AD7091R8_REG_DATA_MSK, val) |
+ FIELD_PREP(AD7091R8_RD_WR_FLAG_MSK, 1) |
+ FIELD_PREP(AD7091R8_REG_ADDR_MSK, reg));
+
+ return spi_write(spi, &st->tx_buf, 2);
+}
+
+static struct regmap_bus ad7091r8_regmap_bus = {
+ .reg_read = ad7091r_regmap_bus_reg_read,
+ .reg_write = ad7091r_regmap_bus_reg_write,
+ .reg_format_endian_default = REGMAP_ENDIAN_BIG,
+ .val_format_endian_default = REGMAP_ENDIAN_BIG,
+};
+
+static const struct regmap_config ad7091r2_reg_conf = AD7091R_SPI_REGMAP_CONFIG(2);
+static const struct regmap_config ad7091r4_reg_conf = AD7091R_SPI_REGMAP_CONFIG(4);
+static const struct regmap_config ad7091r8_reg_conf = AD7091R_SPI_REGMAP_CONFIG(8);
+
+static void ad7091r8_regmap_init(struct ad7091r_state *st,
+ const struct regmap_config *regmap_conf)
+{
+ st->map = devm_regmap_init(st->dev, &ad7091r8_regmap_bus, st,
+ regmap_conf);
+}
+
+static int ad7091r8_gpio_setup(struct ad7091r_state *st)
+{
+ st->convst_gpio = devm_gpiod_get(st->dev, "adi,conversion-start",
+ GPIOD_OUT_LOW);
+ if (IS_ERR(st->convst_gpio))
+ return dev_err_probe(st->dev, PTR_ERR(st->convst_gpio),
+ "Error getting convst GPIO\n");
+
+ st->reset_gpio = devm_gpiod_get_optional(st->dev, "reset",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(st->reset_gpio))
+ return dev_err_probe(st->dev, PTR_ERR(st->convst_gpio),
+ "Error on requesting reset GPIO\n");
+
+ if (st->reset_gpio) {
+ fsleep(20);
+ gpiod_set_value_cansleep(st->reset_gpio, 0);
+ }
+
+ return 0;
+}
+
+static int ad7091r8_set_mode(struct ad7091r_state *st, enum ad7091r_mode mode)
+{
+ /* AD7091R-2/-4/-8 don't set sample/command/autocycle mode in conf reg */
+ st->mode = mode;
+ return 0;
+}
+
+static unsigned int ad7091r8_reg_result_chan_id(unsigned int val)
+{
+ return AD7091R8_REG_RESULT_CH_ID(val);
+}
+
+static struct ad7091r_init_info ad7091r2_init_info = {
+ .info_no_irq = AD7091R_SPI_CHIP_INFO(2, "ad7091r-2"),
+ .regmap_config = &ad7091r2_reg_conf,
+ .init_adc_regmap = &ad7091r8_regmap_init,
+ .setup = &ad7091r8_gpio_setup
+};
+
+static struct ad7091r_init_info ad7091r4_init_info = {
+ .irq_info = AD7091R_SPI_CHIP_INFO_IRQ(4, "ad7091r-4"),
+ .info_no_irq = AD7091R_SPI_CHIP_INFO(4, "ad7091r-4"),
+ .regmap_config = &ad7091r4_reg_conf,
+ .init_adc_regmap = &ad7091r8_regmap_init,
+ .setup = &ad7091r8_gpio_setup
+};
+
+static struct ad7091r_init_info ad7091r8_init_info = {
+ .irq_info = AD7091R_SPI_CHIP_INFO_IRQ(8, "ad7091r-8"),
+ .info_no_irq = AD7091R_SPI_CHIP_INFO(8, "ad7091r-8"),
+ .regmap_config = &ad7091r8_reg_conf,
+ .init_adc_regmap = &ad7091r8_regmap_init,
+ .setup = &ad7091r8_gpio_setup
+};
+
+static int ad7091r8_spi_probe(struct spi_device *spi)
+{
+ const struct ad7091r_init_info *init_info;
+
+ init_info = spi_get_device_match_data(spi);
+ if (!init_info)
+ return -EINVAL;
+
+ return ad7091r_probe(&spi->dev, init_info, spi->irq);
+}
+
+static const struct of_device_id ad7091r8_of_match[] = {
+ { .compatible = "adi,ad7091r2", .data = &ad7091r2_init_info },
+ { .compatible = "adi,ad7091r4", .data = &ad7091r4_init_info },
+ { .compatible = "adi,ad7091r8", .data = &ad7091r8_init_info },
+ { }
+};
+MODULE_DEVICE_TABLE(of, ad7091r8_of_match);
+
+static const struct spi_device_id ad7091r8_spi_id[] = {
+ { "ad7091r2", (kernel_ulong_t)&ad7091r2_init_info },
+ { "ad7091r4", (kernel_ulong_t)&ad7091r4_init_info },
+ { "ad7091r8", (kernel_ulong_t)&ad7091r8_init_info },
+ { }
+};
+MODULE_DEVICE_TABLE(spi, ad7091r8_spi_id);
+
+static struct spi_driver ad7091r8_driver = {
+ .driver = {
+ .name = "ad7091r8",
+ .of_match_table = ad7091r8_of_match,
+ },
+ .probe = ad7091r8_spi_probe,
+ .id_table = ad7091r8_spi_id,
+};
+module_spi_driver(ad7091r8_driver);
+
+MODULE_AUTHOR("Marcelo Schmitt <marcelo.schmitt@analog.com>");
+MODULE_DESCRIPTION("Analog Devices AD7091R8 ADC driver");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(IIO_AD7091R);
Add support for Analog Devices AD7091R-2, AD7091R-4, and AD7091R-8 low power 12-Bit SAR ADCs with SPI interface. Extend ad7091r-base driver so it can be used by the AD7091R-8 driver. Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com> --- drivers/iio/adc/Kconfig | 12 ++ drivers/iio/adc/Makefile | 1 + drivers/iio/adc/ad7091r-base.c | 7 + drivers/iio/adc/ad7091r-base.h | 7 + drivers/iio/adc/ad7091r8.c | 257 +++++++++++++++++++++++++++++++++ 5 files changed, 284 insertions(+) create mode 100644 drivers/iio/adc/ad7091r8.c