Message ID | c84df187ae57c521ef95abea3d51c8a0ae20580c.1623201082.git.vilhelm.gray@gmail.com (mailing list archive) |
---|---|
State | Superseded |
Headers | show |
Series | Introduce the Counter character device interface | expand |
On Wed, 9 Jun 2021 10:31:36 +0900 William Breathitt Gray <vilhelm.gray@gmail.com> wrote: > The LSI/CSI LS7266R1 chip provides programmable output via the FLG pins. > When interrupts are enabled on the ACCES 104-QUAD-8, they occur whenever > FLG1 is active. Four functions are available for the FLG1 signal: Carry, > Compare, Carry-Borrow, and Index. > > Carry: > Interrupt generated on active low Carry signal. Carry > signal toggles every time the respective channel's > counter overflows. > > Compare: > Interrupt generated on active low Compare signal. > Compare signal toggles every time respective channel's > preset register is equal to the respective channel's > counter. > > Carry-Borrow: > Interrupt generated on active low Carry signal and > active low Borrow signal. Carry signal toggles every > time the respective channel's counter overflows. Borrow > signal toggles every time the respective channel's > counter underflows. > > Index: > Interrupt generated on active high Index signal. > > These four functions correspond respectivefly to the following four > Counter event types: COUNTER_EVENT_OVERFLOW, COUNTER_EVENT_THRESHOLD, > COUNTER_EVENT_OVERFLOW_UNDERFLOW, and COUNTER_EVENT_INDEX. Interrupts > push Counter events to event channel X, where 'X' is the respective > channel whose FLG1 activated. > > This patch adds IRQ support for the ACCES 104-QUAD-8. The interrupt line > numbers for the devices may be configured via the irq array module > parameter. > > Acked-by: Syed Nayyar Waris <syednwaris@gmail.com> > Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> I've taken a look at the remainder of the patches I haven't commented on an I think they are all fine. Of course good to get more eyes on this if possible though and perhaps a few more reviews of the interfaces at least from the various counter driver maintainers. Thanks, Jonathan > --- > drivers/counter/104-quad-8.c | 167 +++++++++++++++++++++++++++++++++-- > drivers/counter/Kconfig | 6 +- > 2 files changed, 164 insertions(+), 9 deletions(-) > > diff --git a/drivers/counter/104-quad-8.c b/drivers/counter/104-quad-8.c > index d46b8101f207..09b0b0ba8fe7 100644 > --- a/drivers/counter/104-quad-8.c > +++ b/drivers/counter/104-quad-8.c > @@ -11,6 +11,7 @@ > #include <linux/errno.h> > #include <linux/io.h> > #include <linux/ioport.h> > +#include <linux/interrupt.h> > #include <linux/isa.h> > #include <linux/kernel.h> > #include <linux/module.h> > @@ -25,6 +26,10 @@ static unsigned int num_quad8; > module_param_hw_array(base, uint, ioport, &num_quad8, 0); > MODULE_PARM_DESC(base, "ACCES 104-QUAD-8 base addresses"); > > +static unsigned int irq[max_num_isa_dev(QUAD8_EXTENT)]; > +module_param_hw_array(irq, uint, irq, NULL, 0); > +MODULE_PARM_DESC(irq, "ACCES 104-QUAD-8 interrupt line numbers"); > + > #define QUAD8_NUM_COUNTERS 8 > > /** > @@ -38,6 +43,8 @@ MODULE_PARM_DESC(base, "ACCES 104-QUAD-8 base addresses"); > * @quadrature_scale: array of quadrature mode scale configurations > * @ab_enable: array of A and B inputs enable configurations > * @preset_enable: array of set_to_preset_on_index attribute configurations > + * @irq_trigger: array of current IRQ trigger function configurations > + * @next_irq_trigger: array of next IRQ trigger function configurations > * @synchronous_mode: array of index function synchronous mode configurations > * @index_polarity: array of index function polarity configurations > * @cable_fault_enable: differential encoder cable status enable configurations > @@ -53,13 +60,17 @@ struct quad8 { > unsigned int quadrature_scale[QUAD8_NUM_COUNTERS]; > unsigned int ab_enable[QUAD8_NUM_COUNTERS]; > unsigned int preset_enable[QUAD8_NUM_COUNTERS]; > + unsigned int irq_trigger[QUAD8_NUM_COUNTERS]; > + unsigned int next_irq_trigger[QUAD8_NUM_COUNTERS]; > unsigned int synchronous_mode[QUAD8_NUM_COUNTERS]; > unsigned int index_polarity[QUAD8_NUM_COUNTERS]; > unsigned int cable_fault_enable; > unsigned int base; > }; > > +#define QUAD8_REG_INTERRUPT_STATUS 0x10 > #define QUAD8_REG_CHAN_OP 0x11 > +#define QUAD8_REG_INDEX_INTERRUPT 0x12 > #define QUAD8_REG_INDEX_INPUT_LEVELS 0x16 > #define QUAD8_DIFF_ENCODER_CABLE_STATUS 0x17 > /* Borrow Toggle flip-flop */ > @@ -92,8 +103,8 @@ struct quad8 { > #define QUAD8_RLD_CNTR_OUT 0x10 > /* Transfer Preset Register LSB to FCK Prescaler */ > #define QUAD8_RLD_PRESET_PSC 0x18 > -#define QUAD8_CHAN_OP_ENABLE_COUNTERS 0x00 > #define QUAD8_CHAN_OP_RESET_COUNTERS 0x01 > +#define QUAD8_CHAN_OP_ENABLE_INTERRUPT_FUNC 0x04 > #define QUAD8_CMR_QUADRATURE_X1 0x08 > #define QUAD8_CMR_QUADRATURE_X2 0x10 > #define QUAD8_CMR_QUADRATURE_X4 0x18 > @@ -378,13 +389,103 @@ static int quad8_action_read(struct counter_device *counter, > } > } > > +enum { > + QUAD8_EVENT_NONE = -1, > + QUAD8_EVENT_CARRY = 0, > + QUAD8_EVENT_COMPARE = 1, > + QUAD8_EVENT_CARRY_BORROW = 2, > + QUAD8_EVENT_INDEX = 3, > +}; > + > +static int quad8_events_configure(struct counter_device *counter) > +{ > + struct quad8 *const priv = counter->priv; > + unsigned long irq_enabled = 0; > + unsigned long irqflags; > + size_t channel; > + unsigned long ior_cfg; > + unsigned long base_offset; > + > + spin_lock_irqsave(&priv->lock, irqflags); > + > + /* Enable interrupts for the requested channels, disable for the rest */ > + for (channel = 0; channel < QUAD8_NUM_COUNTERS; channel++) { > + if (priv->next_irq_trigger[channel] == QUAD8_EVENT_NONE) > + continue; > + > + if (priv->irq_trigger[channel] != priv->next_irq_trigger[channel]) { > + /* Save new IRQ function configuration */ > + priv->irq_trigger[channel] = priv->next_irq_trigger[channel]; > + > + /* Load configuration to I/O Control Register */ > + ior_cfg = priv->ab_enable[channel] | > + priv->preset_enable[channel] << 1 | > + priv->irq_trigger[channel] << 3; > + base_offset = priv->base + 2 * channel + 1; > + outb(QUAD8_CTR_IOR | ior_cfg, base_offset); > + } > + > + /* Reset next IRQ trigger function configuration */ > + priv->next_irq_trigger[channel] = QUAD8_EVENT_NONE; > + > + /* Enable IRQ line */ > + irq_enabled |= BIT(channel); > + } > + > + outb(irq_enabled, priv->base + QUAD8_REG_INDEX_INTERRUPT); > + > + spin_unlock_irqrestore(&priv->lock, irqflags); > + > + return 0; > +} > + > +static int quad8_watch_validate(struct counter_device *counter, > + const struct counter_watch *watch) > +{ > + struct quad8 *const priv = counter->priv; > + > + if (watch->channel > QUAD8_NUM_COUNTERS - 1) > + return -EINVAL; > + > + switch (watch->event) { > + case COUNTER_EVENT_OVERFLOW: > + if (priv->next_irq_trigger[watch->channel] == QUAD8_EVENT_NONE) > + priv->next_irq_trigger[watch->channel] = QUAD8_EVENT_CARRY; > + else if (priv->next_irq_trigger[watch->channel] != QUAD8_EVENT_CARRY) > + return -EINVAL; > + return 0; > + case COUNTER_EVENT_THRESHOLD: > + if (priv->next_irq_trigger[watch->channel] == QUAD8_EVENT_NONE) > + priv->next_irq_trigger[watch->channel] = QUAD8_EVENT_COMPARE; > + else if (priv->next_irq_trigger[watch->channel] != QUAD8_EVENT_COMPARE) > + return -EINVAL; > + return 0; > + case COUNTER_EVENT_OVERFLOW_UNDERFLOW: > + if (priv->next_irq_trigger[watch->channel] == QUAD8_EVENT_NONE) > + priv->next_irq_trigger[watch->channel] = QUAD8_EVENT_CARRY_BORROW; > + else if (priv->next_irq_trigger[watch->channel] != QUAD8_EVENT_CARRY_BORROW) > + return -EINVAL; > + return 0; > + case COUNTER_EVENT_INDEX: > + if (priv->next_irq_trigger[watch->channel] == QUAD8_EVENT_NONE) > + priv->next_irq_trigger[watch->channel] = QUAD8_EVENT_INDEX; > + else if (priv->next_irq_trigger[watch->channel] != QUAD8_EVENT_INDEX) > + return -EINVAL; > + return 0; > + default: > + return -EINVAL; > + } > +} > + > static const struct counter_ops quad8_ops = { > .signal_read = quad8_signal_read, > .count_read = quad8_count_read, > .count_write = quad8_count_write, > .function_read = quad8_function_read, > .function_write = quad8_function_write, > - .action_read = quad8_action_read > + .action_read = quad8_action_read, > + .events_configure = quad8_events_configure, > + .watch_validate = quad8_watch_validate, > }; > > static const char *const quad8_index_polarity_modes[] = { > @@ -579,7 +680,8 @@ static int quad8_count_enable_write(struct counter_device *counter, > > priv->ab_enable[count->id] = enable; > > - ior_cfg = enable | priv->preset_enable[count->id] << 1; > + ior_cfg = enable | priv->preset_enable[count->id] << 1 | > + priv->irq_trigger[count->id] << 3; > > /* Load I/O control configuration */ > outb(QUAD8_CTR_IOR | ior_cfg, base_offset + 1); > @@ -728,7 +830,8 @@ static int quad8_count_preset_enable_write(struct counter_device *counter, > > priv->preset_enable[count->id] = preset_enable; > > - ior_cfg = priv->ab_enable[count->id] | preset_enable << 1; > + ior_cfg = priv->ab_enable[count->id] | preset_enable << 1 | > + priv->irq_trigger[count->id] << 3; > > /* Load I/O control configuration to Input / Output Control Register */ > outb(QUAD8_CTR_IOR | ior_cfg, base_offset); > @@ -980,11 +1083,54 @@ static struct counter_count quad8_counts[] = { > QUAD8_COUNT(7, "Channel 8 Count") > }; > > +static irqreturn_t quad8_irq_handler(int irq, void *private) > +{ > + struct quad8 *const priv = private; > + const unsigned long base = priv->base; > + unsigned long irq_status; > + unsigned long channel; > + u8 event; > + > + irq_status = inb(base + QUAD8_REG_INTERRUPT_STATUS); > + if (!irq_status) > + return IRQ_NONE; > + > + for_each_set_bit(channel, &irq_status, QUAD8_NUM_COUNTERS) { > + switch (priv->irq_trigger[channel]) { > + case QUAD8_EVENT_CARRY: > + event = COUNTER_EVENT_OVERFLOW; > + break; > + case QUAD8_EVENT_COMPARE: > + event = COUNTER_EVENT_THRESHOLD; > + break; > + case QUAD8_EVENT_CARRY_BORROW: > + event = COUNTER_EVENT_OVERFLOW_UNDERFLOW; > + break; > + case QUAD8_EVENT_INDEX: > + event = COUNTER_EVENT_INDEX; > + break; > + default: > + /* should never reach this path */ > + WARN_ONCE(true, "invalid interrupt trigger function %u configured for channel %lu\n", > + priv->irq_trigger[channel], channel); > + continue; > + } > + > + counter_push_event(&priv->counter, event, channel); > + } > + > + /* Clear pending interrupts on device */ > + outb(QUAD8_CHAN_OP_ENABLE_INTERRUPT_FUNC, base + QUAD8_REG_CHAN_OP); > + > + return IRQ_HANDLED; > +} > + > static int quad8_probe(struct device *dev, unsigned int id) > { > struct quad8 *priv; > int i, j; > unsigned int base_offset; > + int err; > > if (!devm_request_region(dev, base[id], QUAD8_EXTENT, dev_name(dev))) { > dev_err(dev, "Unable to lock port addresses (0x%X-0x%X)\n", > @@ -1009,6 +1155,8 @@ static int quad8_probe(struct device *dev, unsigned int id) > > spin_lock_init(&priv->lock); > > + /* Reset Index/Interrupt Register */ > + outb(0x00, base[id] + QUAD8_REG_INDEX_INTERRUPT); > /* Reset all counters and disable interrupt function */ > outb(QUAD8_CHAN_OP_RESET_COUNTERS, base[id] + QUAD8_REG_CHAN_OP); > /* Set initial configuration for all counters */ > @@ -1035,11 +1183,18 @@ static int quad8_probe(struct device *dev, unsigned int id) > outb(QUAD8_CTR_IOR, base_offset + 1); > /* Disable index function; negative index polarity */ > outb(QUAD8_CTR_IDR, base_offset + 1); > + /* Initialize next IRQ trigger function configuration */ > + priv->next_irq_trigger[i] = QUAD8_EVENT_NONE; > } > /* Disable Differential Encoder Cable Status for all channels */ > outb(0xFF, base[id] + QUAD8_DIFF_ENCODER_CABLE_STATUS); > - /* Enable all counters */ > - outb(QUAD8_CHAN_OP_ENABLE_COUNTERS, base[id] + QUAD8_REG_CHAN_OP); > + /* Enable all counters and enable interrupt function */ > + outb(QUAD8_CHAN_OP_ENABLE_INTERRUPT_FUNC, base[id] + QUAD8_REG_CHAN_OP); > + > + err = devm_request_irq(dev, irq[id], quad8_irq_handler, IRQF_SHARED, > + priv->counter.name, priv); > + if (err) > + return err; > > return devm_counter_register(dev, &priv->counter); > } > diff --git a/drivers/counter/Kconfig b/drivers/counter/Kconfig > index d5d2540b30c2..3dcdb681c4e4 100644 > --- a/drivers/counter/Kconfig > +++ b/drivers/counter/Kconfig > @@ -23,11 +23,11 @@ config 104_QUAD_8 > A counter's respective error flag may be cleared by performing a write > operation on the respective count value attribute. Although the > 104-QUAD-8 counters have a 25-bit range, only the lower 24 bits may be > - set, either directly or via the counter's preset attribute. Interrupts > - are not supported by this driver. > + set, either directly or via the counter's preset attribute. > > The base port addresses for the devices may be configured via the base > - array module parameter. > + array module parameter. The interrupt line numbers for the devices may > + be configured via the irq array module parameter. > > config INTERRUPT_CNT > tristate "Interrupt counter driver"
diff --git a/drivers/counter/104-quad-8.c b/drivers/counter/104-quad-8.c index d46b8101f207..09b0b0ba8fe7 100644 --- a/drivers/counter/104-quad-8.c +++ b/drivers/counter/104-quad-8.c @@ -11,6 +11,7 @@ #include <linux/errno.h> #include <linux/io.h> #include <linux/ioport.h> +#include <linux/interrupt.h> #include <linux/isa.h> #include <linux/kernel.h> #include <linux/module.h> @@ -25,6 +26,10 @@ static unsigned int num_quad8; module_param_hw_array(base, uint, ioport, &num_quad8, 0); MODULE_PARM_DESC(base, "ACCES 104-QUAD-8 base addresses"); +static unsigned int irq[max_num_isa_dev(QUAD8_EXTENT)]; +module_param_hw_array(irq, uint, irq, NULL, 0); +MODULE_PARM_DESC(irq, "ACCES 104-QUAD-8 interrupt line numbers"); + #define QUAD8_NUM_COUNTERS 8 /** @@ -38,6 +43,8 @@ MODULE_PARM_DESC(base, "ACCES 104-QUAD-8 base addresses"); * @quadrature_scale: array of quadrature mode scale configurations * @ab_enable: array of A and B inputs enable configurations * @preset_enable: array of set_to_preset_on_index attribute configurations + * @irq_trigger: array of current IRQ trigger function configurations + * @next_irq_trigger: array of next IRQ trigger function configurations * @synchronous_mode: array of index function synchronous mode configurations * @index_polarity: array of index function polarity configurations * @cable_fault_enable: differential encoder cable status enable configurations @@ -53,13 +60,17 @@ struct quad8 { unsigned int quadrature_scale[QUAD8_NUM_COUNTERS]; unsigned int ab_enable[QUAD8_NUM_COUNTERS]; unsigned int preset_enable[QUAD8_NUM_COUNTERS]; + unsigned int irq_trigger[QUAD8_NUM_COUNTERS]; + unsigned int next_irq_trigger[QUAD8_NUM_COUNTERS]; unsigned int synchronous_mode[QUAD8_NUM_COUNTERS]; unsigned int index_polarity[QUAD8_NUM_COUNTERS]; unsigned int cable_fault_enable; unsigned int base; }; +#define QUAD8_REG_INTERRUPT_STATUS 0x10 #define QUAD8_REG_CHAN_OP 0x11 +#define QUAD8_REG_INDEX_INTERRUPT 0x12 #define QUAD8_REG_INDEX_INPUT_LEVELS 0x16 #define QUAD8_DIFF_ENCODER_CABLE_STATUS 0x17 /* Borrow Toggle flip-flop */ @@ -92,8 +103,8 @@ struct quad8 { #define QUAD8_RLD_CNTR_OUT 0x10 /* Transfer Preset Register LSB to FCK Prescaler */ #define QUAD8_RLD_PRESET_PSC 0x18 -#define QUAD8_CHAN_OP_ENABLE_COUNTERS 0x00 #define QUAD8_CHAN_OP_RESET_COUNTERS 0x01 +#define QUAD8_CHAN_OP_ENABLE_INTERRUPT_FUNC 0x04 #define QUAD8_CMR_QUADRATURE_X1 0x08 #define QUAD8_CMR_QUADRATURE_X2 0x10 #define QUAD8_CMR_QUADRATURE_X4 0x18 @@ -378,13 +389,103 @@ static int quad8_action_read(struct counter_device *counter, } } +enum { + QUAD8_EVENT_NONE = -1, + QUAD8_EVENT_CARRY = 0, + QUAD8_EVENT_COMPARE = 1, + QUAD8_EVENT_CARRY_BORROW = 2, + QUAD8_EVENT_INDEX = 3, +}; + +static int quad8_events_configure(struct counter_device *counter) +{ + struct quad8 *const priv = counter->priv; + unsigned long irq_enabled = 0; + unsigned long irqflags; + size_t channel; + unsigned long ior_cfg; + unsigned long base_offset; + + spin_lock_irqsave(&priv->lock, irqflags); + + /* Enable interrupts for the requested channels, disable for the rest */ + for (channel = 0; channel < QUAD8_NUM_COUNTERS; channel++) { + if (priv->next_irq_trigger[channel] == QUAD8_EVENT_NONE) + continue; + + if (priv->irq_trigger[channel] != priv->next_irq_trigger[channel]) { + /* Save new IRQ function configuration */ + priv->irq_trigger[channel] = priv->next_irq_trigger[channel]; + + /* Load configuration to I/O Control Register */ + ior_cfg = priv->ab_enable[channel] | + priv->preset_enable[channel] << 1 | + priv->irq_trigger[channel] << 3; + base_offset = priv->base + 2 * channel + 1; + outb(QUAD8_CTR_IOR | ior_cfg, base_offset); + } + + /* Reset next IRQ trigger function configuration */ + priv->next_irq_trigger[channel] = QUAD8_EVENT_NONE; + + /* Enable IRQ line */ + irq_enabled |= BIT(channel); + } + + outb(irq_enabled, priv->base + QUAD8_REG_INDEX_INTERRUPT); + + spin_unlock_irqrestore(&priv->lock, irqflags); + + return 0; +} + +static int quad8_watch_validate(struct counter_device *counter, + const struct counter_watch *watch) +{ + struct quad8 *const priv = counter->priv; + + if (watch->channel > QUAD8_NUM_COUNTERS - 1) + return -EINVAL; + + switch (watch->event) { + case COUNTER_EVENT_OVERFLOW: + if (priv->next_irq_trigger[watch->channel] == QUAD8_EVENT_NONE) + priv->next_irq_trigger[watch->channel] = QUAD8_EVENT_CARRY; + else if (priv->next_irq_trigger[watch->channel] != QUAD8_EVENT_CARRY) + return -EINVAL; + return 0; + case COUNTER_EVENT_THRESHOLD: + if (priv->next_irq_trigger[watch->channel] == QUAD8_EVENT_NONE) + priv->next_irq_trigger[watch->channel] = QUAD8_EVENT_COMPARE; + else if (priv->next_irq_trigger[watch->channel] != QUAD8_EVENT_COMPARE) + return -EINVAL; + return 0; + case COUNTER_EVENT_OVERFLOW_UNDERFLOW: + if (priv->next_irq_trigger[watch->channel] == QUAD8_EVENT_NONE) + priv->next_irq_trigger[watch->channel] = QUAD8_EVENT_CARRY_BORROW; + else if (priv->next_irq_trigger[watch->channel] != QUAD8_EVENT_CARRY_BORROW) + return -EINVAL; + return 0; + case COUNTER_EVENT_INDEX: + if (priv->next_irq_trigger[watch->channel] == QUAD8_EVENT_NONE) + priv->next_irq_trigger[watch->channel] = QUAD8_EVENT_INDEX; + else if (priv->next_irq_trigger[watch->channel] != QUAD8_EVENT_INDEX) + return -EINVAL; + return 0; + default: + return -EINVAL; + } +} + static const struct counter_ops quad8_ops = { .signal_read = quad8_signal_read, .count_read = quad8_count_read, .count_write = quad8_count_write, .function_read = quad8_function_read, .function_write = quad8_function_write, - .action_read = quad8_action_read + .action_read = quad8_action_read, + .events_configure = quad8_events_configure, + .watch_validate = quad8_watch_validate, }; static const char *const quad8_index_polarity_modes[] = { @@ -579,7 +680,8 @@ static int quad8_count_enable_write(struct counter_device *counter, priv->ab_enable[count->id] = enable; - ior_cfg = enable | priv->preset_enable[count->id] << 1; + ior_cfg = enable | priv->preset_enable[count->id] << 1 | + priv->irq_trigger[count->id] << 3; /* Load I/O control configuration */ outb(QUAD8_CTR_IOR | ior_cfg, base_offset + 1); @@ -728,7 +830,8 @@ static int quad8_count_preset_enable_write(struct counter_device *counter, priv->preset_enable[count->id] = preset_enable; - ior_cfg = priv->ab_enable[count->id] | preset_enable << 1; + ior_cfg = priv->ab_enable[count->id] | preset_enable << 1 | + priv->irq_trigger[count->id] << 3; /* Load I/O control configuration to Input / Output Control Register */ outb(QUAD8_CTR_IOR | ior_cfg, base_offset); @@ -980,11 +1083,54 @@ static struct counter_count quad8_counts[] = { QUAD8_COUNT(7, "Channel 8 Count") }; +static irqreturn_t quad8_irq_handler(int irq, void *private) +{ + struct quad8 *const priv = private; + const unsigned long base = priv->base; + unsigned long irq_status; + unsigned long channel; + u8 event; + + irq_status = inb(base + QUAD8_REG_INTERRUPT_STATUS); + if (!irq_status) + return IRQ_NONE; + + for_each_set_bit(channel, &irq_status, QUAD8_NUM_COUNTERS) { + switch (priv->irq_trigger[channel]) { + case QUAD8_EVENT_CARRY: + event = COUNTER_EVENT_OVERFLOW; + break; + case QUAD8_EVENT_COMPARE: + event = COUNTER_EVENT_THRESHOLD; + break; + case QUAD8_EVENT_CARRY_BORROW: + event = COUNTER_EVENT_OVERFLOW_UNDERFLOW; + break; + case QUAD8_EVENT_INDEX: + event = COUNTER_EVENT_INDEX; + break; + default: + /* should never reach this path */ + WARN_ONCE(true, "invalid interrupt trigger function %u configured for channel %lu\n", + priv->irq_trigger[channel], channel); + continue; + } + + counter_push_event(&priv->counter, event, channel); + } + + /* Clear pending interrupts on device */ + outb(QUAD8_CHAN_OP_ENABLE_INTERRUPT_FUNC, base + QUAD8_REG_CHAN_OP); + + return IRQ_HANDLED; +} + static int quad8_probe(struct device *dev, unsigned int id) { struct quad8 *priv; int i, j; unsigned int base_offset; + int err; if (!devm_request_region(dev, base[id], QUAD8_EXTENT, dev_name(dev))) { dev_err(dev, "Unable to lock port addresses (0x%X-0x%X)\n", @@ -1009,6 +1155,8 @@ static int quad8_probe(struct device *dev, unsigned int id) spin_lock_init(&priv->lock); + /* Reset Index/Interrupt Register */ + outb(0x00, base[id] + QUAD8_REG_INDEX_INTERRUPT); /* Reset all counters and disable interrupt function */ outb(QUAD8_CHAN_OP_RESET_COUNTERS, base[id] + QUAD8_REG_CHAN_OP); /* Set initial configuration for all counters */ @@ -1035,11 +1183,18 @@ static int quad8_probe(struct device *dev, unsigned int id) outb(QUAD8_CTR_IOR, base_offset + 1); /* Disable index function; negative index polarity */ outb(QUAD8_CTR_IDR, base_offset + 1); + /* Initialize next IRQ trigger function configuration */ + priv->next_irq_trigger[i] = QUAD8_EVENT_NONE; } /* Disable Differential Encoder Cable Status for all channels */ outb(0xFF, base[id] + QUAD8_DIFF_ENCODER_CABLE_STATUS); - /* Enable all counters */ - outb(QUAD8_CHAN_OP_ENABLE_COUNTERS, base[id] + QUAD8_REG_CHAN_OP); + /* Enable all counters and enable interrupt function */ + outb(QUAD8_CHAN_OP_ENABLE_INTERRUPT_FUNC, base[id] + QUAD8_REG_CHAN_OP); + + err = devm_request_irq(dev, irq[id], quad8_irq_handler, IRQF_SHARED, + priv->counter.name, priv); + if (err) + return err; return devm_counter_register(dev, &priv->counter); } diff --git a/drivers/counter/Kconfig b/drivers/counter/Kconfig index d5d2540b30c2..3dcdb681c4e4 100644 --- a/drivers/counter/Kconfig +++ b/drivers/counter/Kconfig @@ -23,11 +23,11 @@ config 104_QUAD_8 A counter's respective error flag may be cleared by performing a write operation on the respective count value attribute. Although the 104-QUAD-8 counters have a 25-bit range, only the lower 24 bits may be - set, either directly or via the counter's preset attribute. Interrupts - are not supported by this driver. + set, either directly or via the counter's preset attribute. The base port addresses for the devices may be configured via the base - array module parameter. + array module parameter. The interrupt line numbers for the devices may + be configured via the irq array module parameter. config INTERRUPT_CNT tristate "Interrupt counter driver"