@@ -38,8 +38,7 @@
#include <linux/gpio/consumer.h>
#include <linux/input/mt.h>
#include <linux/input/touchscreen.h>
-
-#define MAX_SUPPORT_POINTS 5
+#include <linux/of_device.h>
#define WORK_REGISTER_THRESHOLD 0x00
#define WORK_REGISTER_REPORT_RATE 0x08
@@ -105,6 +104,7 @@ struct edt_ft5x06_ts_data {
int gain;
int offset;
int report_rate;
+ int max_support_points;
char name[EDT_NAME_LEN];
@@ -112,6 +112,10 @@ struct edt_ft5x06_ts_data {
enum edt_ver version;
};
+struct edt_i2c_chip_data {
+ int max_support_points;
+};
+
static int edt_ft5x06_ts_readwrite(struct i2c_client *client,
u16 wr_len, u8 *wr_buf,
u16 rd_len, u8 *rd_buf)
@@ -181,7 +185,7 @@ static irqreturn_t edt_ft5x06_ts_isr(int irq, void *dev_id)
crclen = 1; /* length of the crc data */
/* how many bytes to listen for */
- datalen = tplen * MAX_SUPPORT_POINTS + offset + crclen;
+ datalen = tplen * tsdata->max_support_points + offset + crclen;
break;
case M09:
@@ -189,7 +193,7 @@ static irqreturn_t edt_ft5x06_ts_isr(int irq, void *dev_id)
offset = 1;
tplen = 6;
crclen = 0;
- datalen = tplen * MAX_SUPPORT_POINTS + offset + crclen;
+ datalen = tplen * tsdata->max_support_points + offset + crclen;
break;
default:
@@ -221,7 +225,7 @@ static irqreturn_t edt_ft5x06_ts_isr(int irq, void *dev_id)
goto out;
}
- for (i = 0; i < MAX_SUPPORT_POINTS; i++) {
+ for (i = 0; i < tsdata->max_support_points; i++) {
u8 *buf = &rdbuf[i * tplen + offset];
bool down;
@@ -874,6 +878,32 @@ edt_ft5x06_ts_set_regs(struct edt_ft5x06_ts_data *tsdata)
}
}
+#ifdef CONFIG_OF
+
+static const struct of_device_id edt_ft5x06_of_match[];
+
+static void edt_ft5x06_ts_set_max_support_points(struct device *dev,
+ struct edt_ft5x06_ts_data *tsdata)
+{
+ struct edt_i2c_chip_data *chip_data;
+ const struct of_device_id *match;
+
+ match = of_match_device(of_match_ptr(edt_ft5x06_of_match), dev);
+
+ if (match) {
+ chip_data = (struct edt_i2c_chip_data *)match->data;
+ tsdata->max_support_points = chip_data->max_support_points;
+ } else {
+ tsdata->max_support_points = 5;
+ }
+}
+#else
+static void edt_ft5x06_ts_set_max_support_points(struct device *dev,
+ struct edt_ft5x06_ts_data *tsdata)
+{
+}
+#endif
+
static int edt_ft5x06_ts_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
@@ -891,6 +921,8 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
return -ENOMEM;
}
+ edt_ft5x06_ts_set_max_support_points(&client->dev, tsdata);
+
tsdata->reset_gpio = devm_gpiod_get_optional(&client->dev,
"reset", GPIOD_OUT_HIGH);
if (IS_ERR(tsdata->reset_gpio)) {
@@ -956,7 +988,8 @@ static int edt_ft5x06_ts_probe(struct i2c_client *client,
touchscreen_parse_properties(input, true);
- error = input_mt_init_slots(input, MAX_SUPPORT_POINTS, INPUT_MT_DIRECT);
+ error = input_mt_init_slots(input, tsdata->max_support_points,
+ INPUT_MT_DIRECT);
if (error) {
dev_err(&client->dev, "Unable to init MT slots.\n");
return error;
@@ -1042,10 +1075,15 @@ static const struct i2c_device_id edt_ft5x06_ts_id[] = {
MODULE_DEVICE_TABLE(i2c, edt_ft5x06_ts_id);
#ifdef CONFIG_OF
+
+static const struct edt_i2c_chip_data edt_ft5x06_data = {
+ .max_support_points = 5,
+};
+
static const struct of_device_id edt_ft5x06_of_match[] = {
- { .compatible = "edt,edt-ft5206", },
- { .compatible = "edt,edt-ft5306", },
- { .compatible = "edt,edt-ft5406", },
+ { .compatible = "edt,edt-ft5206", .data = &edt_ft5x06_data},
+ { .compatible = "edt,edt-ft5306", .data = &edt_ft5x06_data},
+ { .compatible = "edt,edt-ft5406", .data = &edt_ft5x06_data},
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, edt_ft5x06_of_match);
Update the code so that the maximum supported points aren't hard coded but can be changed. Set the maximum support points based on the data passed along side the compatible field. Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com> --- Changes since RFC: None drivers/input/touchscreen/edt-ft5x06.c | 56 ++++++++++++++++++++++++++++------ 1 file changed, 47 insertions(+), 9 deletions(-)