@@ -939,10 +939,14 @@ config TOUCHSCREEN_TSC_SERIO
To compile this driver as a module, choose M here: the
module will be called tsc40.
+config TOUCHSCREEN_TSC200X_CORE
+ tristate
+
config TOUCHSCREEN_TSC2005
tristate "TSC2005 based touchscreens"
depends on SPI_MASTER
select REGMAP_SPI
+ select TOUCHSCREEN_TSC200X_CORE
help
Say Y here if you have a TSC2005 based touchscreen.
@@ -69,6 +69,7 @@ obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213) += touchit213.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT) += touchright.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHWIN) += touchwin.o
obj-$(CONFIG_TOUCHSCREEN_TSC_SERIO) += tsc40.o
+obj-$(CONFIG_TOUCHSCREEN_TSC200X_CORE) += tsc200x-core.o
obj-$(CONFIG_TOUCHSCREEN_TSC2005) += tsc2005.o
obj-$(CONFIG_TOUCHSCREEN_TSC2007) += tsc2007.o
obj-$(CONFIG_TOUCHSCREEN_UCB1400) += ucb1400_ts.o
@@ -2,9 +2,10 @@
* TSC2005 touchscreen driver
*
* Copyright (C) 2006-2010 Nokia Corporation
+ * Copyright (C) 2015 QWERTY Embedded Design
+ * Copyright (C) 2015 EMAC Inc.
*
- * Author: Lauri Leukkunen <lauri.leukkunen@nokia.com>
- * based on TSC2301 driver by Klaus K. Pedersen <klaus.k.pedersen@nokia.com>
+ * Based on original tsc2005.c by Lauri Leukkunen <lauri.leukkunen@nokia.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
@@ -15,192 +16,34 @@
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
*/
-#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/input.h>
-#include <linux/input/touchscreen.h>
-#include <linux/interrupt.h>
-#include <linux/delay.h>
#include <linux/pm.h>
#include <linux/of.h>
#include <linux/spi/spi.h>
-#include <linux/spi/tsc2005.h>
-#include <linux/regulator/consumer.h>
#include <linux/regmap.h>
-#include <linux/gpio/consumer.h>
-
-/*
- * The touchscreen interface operates as follows:
- *
- * 1) Pen is pressed against the touchscreen.
- * 2) TSC2005 performs AD conversion.
- * 3) After the conversion is done TSC2005 drives DAV line down.
- * 4) GPIO IRQ is received and tsc2005_irq_thread() is scheduled.
- * 5) tsc2005_irq_thread() queues up an spi transfer to fetch the x, y, z1, z2
- * values.
- * 6) tsc2005_irq_thread() reports coordinates to input layer and sets up
- * tsc2005_penup_timer() to be called after TSC2005_PENUP_TIME_MS (40ms).
- * 7) When the penup timer expires, there have not been touch or DAV interrupts
- * during the last 40ms which means the pen has been lifted.
- *
- * ESD recovery via a hardware reset is done if the TSC2005 doesn't respond
- * after a configurable period (in ms) of activity. If esd_timeout is 0, the
- * watchdog is disabled.
- */
-
-/* control byte 1 */
-#define TSC2005_CMD 0x80
-#define TSC2005_CMD_NORMAL 0x00
-#define TSC2005_CMD_STOP 0x01
-#define TSC2005_CMD_12BIT 0x04
-
-/* control byte 0 */
-#define TSC2005_REG_READ 0x01 /* R/W access */
-#define TSC2005_REG_PND0 0x02 /* Power Not Down Control */
-#define TSC2005_REG_X (0x0 << 3)
-#define TSC2005_REG_Y (0x1 << 3)
-#define TSC2005_REG_Z1 (0x2 << 3)
-#define TSC2005_REG_Z2 (0x3 << 3)
-#define TSC2005_REG_AUX (0x4 << 3)
-#define TSC2005_REG_TEMP1 (0x5 << 3)
-#define TSC2005_REG_TEMP2 (0x6 << 3)
-#define TSC2005_REG_STATUS (0x7 << 3)
-#define TSC2005_REG_AUX_HIGH (0x8 << 3)
-#define TSC2005_REG_AUX_LOW (0x9 << 3)
-#define TSC2005_REG_TEMP_HIGH (0xA << 3)
-#define TSC2005_REG_TEMP_LOW (0xB << 3)
-#define TSC2005_REG_CFR0 (0xC << 3)
-#define TSC2005_REG_CFR1 (0xD << 3)
-#define TSC2005_REG_CFR2 (0xE << 3)
-#define TSC2005_REG_CONV_FUNC (0xF << 3)
-
-/* configuration register 0 */
-#define TSC2005_CFR0_PRECHARGE_276US 0x0040
-#define TSC2005_CFR0_STABTIME_1MS 0x0300
-#define TSC2005_CFR0_CLOCK_1MHZ 0x1000
-#define TSC2005_CFR0_RESOLUTION12 0x2000
-#define TSC2005_CFR0_PENMODE 0x8000
-#define TSC2005_CFR0_INITVALUE (TSC2005_CFR0_STABTIME_1MS | \
- TSC2005_CFR0_CLOCK_1MHZ | \
- TSC2005_CFR0_RESOLUTION12 | \
- TSC2005_CFR0_PRECHARGE_276US | \
- TSC2005_CFR0_PENMODE)
-
-/* bits common to both read and write of configuration register 0 */
-#define TSC2005_CFR0_RW_MASK 0x3fff
-
-/* configuration register 1 */
-#define TSC2005_CFR1_BATCHDELAY_4MS 0x0003
-#define TSC2005_CFR1_INITVALUE TSC2005_CFR1_BATCHDELAY_4MS
-
-/* configuration register 2 */
-#define TSC2005_CFR2_MAVE_Z 0x0004
-#define TSC2005_CFR2_MAVE_Y 0x0008
-#define TSC2005_CFR2_MAVE_X 0x0010
-#define TSC2005_CFR2_AVG_7 0x0800
-#define TSC2005_CFR2_MEDIUM_15 0x3000
-#define TSC2005_CFR2_INITVALUE (TSC2005_CFR2_MAVE_X | \
- TSC2005_CFR2_MAVE_Y | \
- TSC2005_CFR2_MAVE_Z | \
- TSC2005_CFR2_MEDIUM_15 | \
- TSC2005_CFR2_AVG_7)
-
-#define MAX_12BIT 0xfff
-#define TSC2005_DEF_X_FUZZ 4
-#define TSC2005_DEF_Y_FUZZ 8
-#define TSC2005_DEF_P_FUZZ 2
-#define TSC2005_DEF_RESISTOR 280
-
-#define TSC2005_SPI_MAX_SPEED_HZ 10000000
-#define TSC2005_PENUP_TIME_MS 40
-
-static const struct regmap_range tsc2005_writable_ranges[] = {
- regmap_reg_range(TSC2005_REG_AUX_HIGH, TSC2005_REG_CFR2),
-};
-
-static const struct regmap_access_table tsc2005_writable_table = {
- .yes_ranges = tsc2005_writable_ranges,
- .n_yes_ranges = ARRAY_SIZE(tsc2005_writable_ranges),
-};
-
-static struct regmap_config tsc2005_regmap_config = {
- .reg_bits = 8,
- .val_bits = 16,
- .reg_stride = 0x08,
- .max_register = 0x78,
- .read_flag_mask = TSC2005_REG_READ,
- .write_flag_mask = TSC2005_REG_PND0,
- .wr_table = &tsc2005_writable_table,
- .use_single_rw = true,
-};
-
-struct tsc2005_data {
- u16 x;
- u16 y;
- u16 z1;
- u16 z2;
-} __packed;
-#define TSC2005_DATA_REGS 4
-
-struct tsc2005 {
- struct spi_device *spi;
- struct regmap *regmap;
-
- struct input_dev *idev;
- char phys[32];
-
- struct mutex mutex;
-
- /* raw copy of previous x,y,z */
- int in_x;
- int in_y;
- int in_z1;
- int in_z2;
-
- spinlock_t lock;
- struct timer_list penup_timer;
+#include "tsc200x-core.h"
- unsigned int esd_timeout;
- struct delayed_work esd_work;
- unsigned long last_valid_interrupt;
-
- unsigned int x_plate_ohm;
-
- bool opened;
- bool suspended;
-
- bool pen_down;
-
- struct regulator *vio;
-
- struct gpio_desc *reset_gpio;
- void (*set_reset)(bool enable);
-};
-
-static int tsc2005_cmd(struct tsc2005 *ts, u8 cmd)
+static int tsc2005_cmd(struct device *dev, u8 cmd)
{
u8 tx = TSC2005_CMD | TSC2005_CMD_12BIT | cmd;
struct spi_transfer xfer = {
- .tx_buf = &tx,
- .len = 1,
- .bits_per_word = 8,
+ .tx_buf = &tx,
+ .len = 1,
+ .bits_per_word = 8,
};
struct spi_message msg;
+ struct spi_device *spi = to_spi_device(dev);
int error;
spi_message_init(&msg);
spi_message_add_tail(&xfer, &msg);
- error = spi_sync(ts->spi, &msg);
+ error = spi_sync(spi, &msg);
if (error) {
- dev_err(&ts->spi->dev, "%s: failed, command: %x, error: %d\n",
+ dev_err(dev, "%s: failed, command: %x, spi error: %d\n",
__func__, cmd, error);
return error;
}
@@ -208,382 +51,10 @@ static int tsc2005_cmd(struct tsc2005 *ts, u8 cmd)
return 0;
}
-static void tsc2005_update_pen_state(struct tsc2005 *ts,
- int x, int y, int pressure)
-{
- if (pressure) {
- input_report_abs(ts->idev, ABS_X, x);
- input_report_abs(ts->idev, ABS_Y, y);
- input_report_abs(ts->idev, ABS_PRESSURE, pressure);
- if (!ts->pen_down) {
- input_report_key(ts->idev, BTN_TOUCH, !!pressure);
- ts->pen_down = true;
- }
- } else {
- input_report_abs(ts->idev, ABS_PRESSURE, 0);
- if (ts->pen_down) {
- input_report_key(ts->idev, BTN_TOUCH, 0);
- ts->pen_down = false;
- }
- }
- input_sync(ts->idev);
- dev_dbg(&ts->spi->dev, "point(%4d,%4d), pressure (%4d)\n", x, y,
- pressure);
-}
-
-static irqreturn_t tsc2005_irq_thread(int irq, void *_ts)
-{
- struct tsc2005 *ts = _ts;
- unsigned long flags;
- unsigned int pressure;
- struct tsc2005_data tsdata;
- int error;
-
- /* read the coordinates */
- error = regmap_bulk_read(ts->regmap, TSC2005_REG_X, &tsdata,
- TSC2005_DATA_REGS);
- if (unlikely(error))
- goto out;
-
- /* validate position */
- if (unlikely(tsdata.x > MAX_12BIT || tsdata.y > MAX_12BIT))
- goto out;
-
- /* Skip reading if the pressure components are out of range */
- if (unlikely(tsdata.z1 == 0 || tsdata.z2 > MAX_12BIT))
- goto out;
- if (unlikely(tsdata.z1 >= tsdata.z2))
- goto out;
-
- /*
- * Skip point if this is a pen down with the exact same values as
- * the value before pen-up - that implies SPI fed us stale data
- */
- if (!ts->pen_down &&
- ts->in_x == tsdata.x && ts->in_y == tsdata.y &&
- ts->in_z1 == tsdata.z1 && ts->in_z2 == tsdata.z2) {
- goto out;
- }
-
- /*
- * At this point we are happy we have a valid and useful reading.
- * Remember it for later comparisons. We may now begin downsampling.
- */
- ts->in_x = tsdata.x;
- ts->in_y = tsdata.y;
- ts->in_z1 = tsdata.z1;
- ts->in_z2 = tsdata.z2;
-
- /* Compute touch pressure resistance using equation #1 */
- pressure = tsdata.x * (tsdata.z2 - tsdata.z1) / tsdata.z1;
- pressure = pressure * ts->x_plate_ohm / 4096;
- if (unlikely(pressure > MAX_12BIT))
- goto out;
-
- spin_lock_irqsave(&ts->lock, flags);
-
- tsc2005_update_pen_state(ts, tsdata.x, tsdata.y, pressure);
- mod_timer(&ts->penup_timer,
- jiffies + msecs_to_jiffies(TSC2005_PENUP_TIME_MS));
-
- spin_unlock_irqrestore(&ts->lock, flags);
-
- ts->last_valid_interrupt = jiffies;
-out:
- return IRQ_HANDLED;
-}
-
-static void tsc2005_penup_timer(unsigned long data)
-{
- struct tsc2005 *ts = (struct tsc2005 *)data;
- unsigned long flags;
-
- spin_lock_irqsave(&ts->lock, flags);
- tsc2005_update_pen_state(ts, 0, 0, 0);
- spin_unlock_irqrestore(&ts->lock, flags);
-}
-
-static void tsc2005_start_scan(struct tsc2005 *ts)
-{
- regmap_write(ts->regmap, TSC2005_REG_CFR0, TSC2005_CFR0_INITVALUE);
- regmap_write(ts->regmap, TSC2005_REG_CFR1, TSC2005_CFR1_INITVALUE);
- regmap_write(ts->regmap, TSC2005_REG_CFR2, TSC2005_CFR2_INITVALUE);
- tsc2005_cmd(ts, TSC2005_CMD_NORMAL);
-}
-
-static void tsc2005_stop_scan(struct tsc2005 *ts)
-{
- tsc2005_cmd(ts, TSC2005_CMD_STOP);
-}
-
-static void tsc2005_set_reset(struct tsc2005 *ts, bool enable)
-{
- if (ts->reset_gpio)
- gpiod_set_value_cansleep(ts->reset_gpio, enable);
- else if (ts->set_reset)
- ts->set_reset(enable);
-}
-
-/* must be called with ts->mutex held */
-static void __tsc2005_disable(struct tsc2005 *ts)
-{
- tsc2005_stop_scan(ts);
-
- disable_irq(ts->spi->irq);
- del_timer_sync(&ts->penup_timer);
-
- cancel_delayed_work_sync(&ts->esd_work);
-
- enable_irq(ts->spi->irq);
-}
-
-/* must be called with ts->mutex held */
-static void __tsc2005_enable(struct tsc2005 *ts)
-{
- tsc2005_start_scan(ts);
-
- if (ts->esd_timeout && (ts->set_reset || ts->reset_gpio)) {
- ts->last_valid_interrupt = jiffies;
- schedule_delayed_work(&ts->esd_work,
- round_jiffies_relative(
- msecs_to_jiffies(ts->esd_timeout)));
- }
-
-}
-
-static ssize_t tsc2005_selftest_show(struct device *dev,
- struct device_attribute *attr,
- char *buf)
-{
- struct tsc2005 *ts = dev_get_drvdata(dev);
- unsigned int temp_high;
- unsigned int temp_high_orig;
- unsigned int temp_high_test;
- bool success = true;
- int error;
-
- mutex_lock(&ts->mutex);
-
- /*
- * Test TSC2005 communications via temp high register.
- */
- __tsc2005_disable(ts);
-
- error = regmap_read(ts->regmap, TSC2005_REG_TEMP_HIGH, &temp_high_orig);
- if (error) {
- dev_warn(dev, "selftest failed: read error %d\n", error);
- success = false;
- goto out;
- }
-
- temp_high_test = (temp_high_orig - 1) & MAX_12BIT;
-
- error = regmap_write(ts->regmap, TSC2005_REG_TEMP_HIGH, temp_high_test);
- if (error) {
- dev_warn(dev, "selftest failed: write error %d\n", error);
- success = false;
- goto out;
- }
-
- error = regmap_read(ts->regmap, TSC2005_REG_TEMP_HIGH, &temp_high);
- if (error) {
- dev_warn(dev, "selftest failed: read error %d after write\n",
- error);
- success = false;
- goto out;
- }
-
- if (temp_high != temp_high_test) {
- dev_warn(dev, "selftest failed: %d != %d\n",
- temp_high, temp_high_test);
- success = false;
- }
-
- /* hardware reset */
- tsc2005_set_reset(ts, false);
- usleep_range(100, 500); /* only 10us required */
- tsc2005_set_reset(ts, true);
-
- if (!success)
- goto out;
-
- /* test that the reset really happened */
- error = regmap_read(ts->regmap, TSC2005_REG_TEMP_HIGH, &temp_high);
- if (error) {
- dev_warn(dev, "selftest failed: read error %d after reset\n",
- error);
- success = false;
- goto out;
- }
-
- if (temp_high != temp_high_orig) {
- dev_warn(dev, "selftest failed after reset: %d != %d\n",
- temp_high, temp_high_orig);
- success = false;
- }
-
-out:
- __tsc2005_enable(ts);
- mutex_unlock(&ts->mutex);
-
- return sprintf(buf, "%d\n", success);
-}
-
-static DEVICE_ATTR(selftest, S_IRUGO, tsc2005_selftest_show, NULL);
-
-static struct attribute *tsc2005_attrs[] = {
- &dev_attr_selftest.attr,
- NULL
-};
-
-static umode_t tsc2005_attr_is_visible(struct kobject *kobj,
- struct attribute *attr, int n)
-{
- struct device *dev = container_of(kobj, struct device, kobj);
- struct tsc2005 *ts = dev_get_drvdata(dev);
- umode_t mode = attr->mode;
-
- if (attr == &dev_attr_selftest.attr) {
- if (!ts->set_reset && !ts->reset_gpio)
- mode = 0;
- }
-
- return mode;
-}
-
-static const struct attribute_group tsc2005_attr_group = {
- .is_visible = tsc2005_attr_is_visible,
- .attrs = tsc2005_attrs,
-};
-
-static void tsc2005_esd_work(struct work_struct *work)
-{
- struct tsc2005 *ts = container_of(work, struct tsc2005, esd_work.work);
- int error;
- unsigned int r;
-
- if (!mutex_trylock(&ts->mutex)) {
- /*
- * If the mutex is taken, it means that disable or enable is in
- * progress. In that case just reschedule the work. If the work
- * is not needed, it will be canceled by disable.
- */
- goto reschedule;
- }
-
- if (time_is_after_jiffies(ts->last_valid_interrupt +
- msecs_to_jiffies(ts->esd_timeout)))
- goto out;
-
- /* We should be able to read register without disabling interrupts. */
- error = regmap_read(ts->regmap, TSC2005_REG_CFR0, &r);
- if (!error &&
- !((r ^ TSC2005_CFR0_INITVALUE) & TSC2005_CFR0_RW_MASK)) {
- goto out;
- }
-
- /*
- * If we could not read our known value from configuration register 0
- * then we should reset the controller as if from power-up and start
- * scanning again.
- */
- dev_info(&ts->spi->dev, "TSC2005 not responding - resetting\n");
-
- disable_irq(ts->spi->irq);
- del_timer_sync(&ts->penup_timer);
-
- tsc2005_update_pen_state(ts, 0, 0, 0);
-
- tsc2005_set_reset(ts, false);
- usleep_range(100, 500); /* only 10us required */
- tsc2005_set_reset(ts, true);
-
- enable_irq(ts->spi->irq);
- tsc2005_start_scan(ts);
-
-out:
- mutex_unlock(&ts->mutex);
-reschedule:
- /* re-arm the watchdog */
- schedule_delayed_work(&ts->esd_work,
- round_jiffies_relative(
- msecs_to_jiffies(ts->esd_timeout)));
-}
-
-static int tsc2005_open(struct input_dev *input)
-{
- struct tsc2005 *ts = input_get_drvdata(input);
-
- mutex_lock(&ts->mutex);
-
- if (!ts->suspended)
- __tsc2005_enable(ts);
-
- ts->opened = true;
-
- mutex_unlock(&ts->mutex);
-
- return 0;
-}
-
-static void tsc2005_close(struct input_dev *input)
-{
- struct tsc2005 *ts = input_get_drvdata(input);
-
- mutex_lock(&ts->mutex);
-
- if (!ts->suspended)
- __tsc2005_disable(ts);
-
- ts->opened = false;
-
- mutex_unlock(&ts->mutex);
-}
-
static int tsc2005_probe(struct spi_device *spi)
{
- const struct tsc2005_platform_data *pdata = dev_get_platdata(&spi->dev);
- struct device_node *np = spi->dev.of_node;
-
- struct tsc2005 *ts;
- struct input_dev *input_dev;
- unsigned int max_x = MAX_12BIT;
- unsigned int max_y = MAX_12BIT;
- unsigned int max_p = MAX_12BIT;
- unsigned int fudge_x = TSC2005_DEF_X_FUZZ;
- unsigned int fudge_y = TSC2005_DEF_Y_FUZZ;
- unsigned int fudge_p = TSC2005_DEF_P_FUZZ;
- unsigned int x_plate_ohm = TSC2005_DEF_RESISTOR;
- unsigned int esd_timeout;
int error;
- if (!np && !pdata) {
- dev_err(&spi->dev, "no platform data\n");
- return -ENODEV;
- }
-
- if (spi->irq <= 0) {
- dev_err(&spi->dev, "no irq\n");
- return -ENODEV;
- }
-
- if (pdata) {
- fudge_x = pdata->ts_x_fudge;
- fudge_y = pdata->ts_y_fudge;
- fudge_p = pdata->ts_pressure_fudge;
- max_x = pdata->ts_x_max;
- max_y = pdata->ts_y_max;
- max_p = pdata->ts_pressure_max;
- x_plate_ohm = pdata->ts_x_plate_ohm;
- esd_timeout = pdata->esd_timeout_ms;
- } else {
- x_plate_ohm = TSC2005_DEF_RESISTOR;
- of_property_read_u32(np, "ti,x-plate-ohms", &x_plate_ohm);
- esd_timeout = 0;
- of_property_read_u32(np, "ti,esd-recovery-timeout-ms",
- &esd_timeout);
- }
-
spi->mode = SPI_MODE_0;
spi->bits_per_word = 8;
if (!spi->max_speed_hz)
@@ -593,167 +64,21 @@ static int tsc2005_probe(struct spi_device *spi)
if (error)
return error;
- ts = devm_kzalloc(&spi->dev, sizeof(*ts), GFP_KERNEL);
- if (!ts)
- return -ENOMEM;
-
- input_dev = devm_input_allocate_device(&spi->dev);
- if (!input_dev)
- return -ENOMEM;
-
- ts->spi = spi;
- ts->idev = input_dev;
-
- ts->regmap = devm_regmap_init_spi(spi, &tsc2005_regmap_config);
- if (IS_ERR(ts->regmap))
- return PTR_ERR(ts->regmap);
-
- ts->x_plate_ohm = x_plate_ohm;
- ts->esd_timeout = esd_timeout;
-
- ts->reset_gpio = devm_gpiod_get_optional(&spi->dev, "reset",
- GPIOD_OUT_HIGH);
- if (IS_ERR(ts->reset_gpio)) {
- error = PTR_ERR(ts->reset_gpio);
- dev_err(&spi->dev, "error acquiring reset gpio: %d\n", error);
- return error;
- }
-
- ts->vio = devm_regulator_get_optional(&spi->dev, "vio");
- if (IS_ERR(ts->vio)) {
- error = PTR_ERR(ts->vio);
- dev_err(&spi->dev, "vio regulator missing (%d)", error);
- return error;
- }
-
- if (!ts->reset_gpio && pdata)
- ts->set_reset = pdata->set_reset;
-
- mutex_init(&ts->mutex);
-
- spin_lock_init(&ts->lock);
- setup_timer(&ts->penup_timer, tsc2005_penup_timer, (unsigned long)ts);
-
- INIT_DELAYED_WORK(&ts->esd_work, tsc2005_esd_work);
-
- snprintf(ts->phys, sizeof(ts->phys),
- "%s/input-ts", dev_name(&spi->dev));
-
- input_dev->name = "TSC2005 touchscreen";
- input_dev->phys = ts->phys;
- input_dev->id.bustype = BUS_SPI;
- input_dev->dev.parent = &spi->dev;
- input_dev->evbit[0] = BIT(EV_ABS) | BIT(EV_KEY);
- input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
-
- input_set_abs_params(input_dev, ABS_X, 0, max_x, fudge_x, 0);
- input_set_abs_params(input_dev, ABS_Y, 0, max_y, fudge_y, 0);
- input_set_abs_params(input_dev, ABS_PRESSURE, 0, max_p, fudge_p, 0);
-
- if (np)
- touchscreen_parse_properties(input_dev, false);
-
- input_dev->open = tsc2005_open;
- input_dev->close = tsc2005_close;
-
- input_set_drvdata(input_dev, ts);
-
- /* Ensure the touchscreen is off */
- tsc2005_stop_scan(ts);
-
- error = devm_request_threaded_irq(&spi->dev, spi->irq, NULL,
- tsc2005_irq_thread,
- IRQF_TRIGGER_RISING | IRQF_ONESHOT,
- "tsc2005", ts);
- if (error) {
- dev_err(&spi->dev, "Failed to request irq, err: %d\n", error);
- return error;
- }
-
- /* enable regulator for DT */
- if (ts->vio) {
- error = regulator_enable(ts->vio);
- if (error)
- return error;
- }
-
- dev_set_drvdata(&spi->dev, ts);
- error = sysfs_create_group(&spi->dev.kobj, &tsc2005_attr_group);
- if (error) {
- dev_err(&spi->dev,
- "Failed to create sysfs attributes, err: %d\n", error);
- goto disable_regulator;
- }
-
- error = input_register_device(ts->idev);
- if (error) {
- dev_err(&spi->dev,
- "Failed to register input device, err: %d\n", error);
- goto err_remove_sysfs;
- }
-
- irq_set_irq_wake(spi->irq, 1);
- return 0;
-
-err_remove_sysfs:
- sysfs_remove_group(&spi->dev.kobj, &tsc2005_attr_group);
-disable_regulator:
- if (ts->vio)
- regulator_disable(ts->vio);
- return error;
+ return tsc200x_probe(&spi->dev, spi->irq, BUS_SPI,
+ devm_regmap_init_spi(spi, &tsc200x_regmap_config),
+ &tsc2005_cmd);
}
static int tsc2005_remove(struct spi_device *spi)
{
- struct tsc2005 *ts = dev_get_drvdata(&spi->dev);
-
- sysfs_remove_group(&spi->dev.kobj, &tsc2005_attr_group);
-
- if (ts->vio)
- regulator_disable(ts->vio);
-
- return 0;
-}
-
-static int __maybe_unused tsc2005_suspend(struct device *dev)
-{
- struct tsc2005 *ts = dev_get_drvdata(dev);
-
- mutex_lock(&ts->mutex);
-
- if (!ts->suspended && ts->opened)
- __tsc2005_disable(ts);
-
- ts->suspended = true;
-
- mutex_unlock(&ts->mutex);
-
- return 0;
-}
-
-static int __maybe_unused tsc2005_resume(struct device *dev)
-{
- struct tsc2005 *ts = dev_get_drvdata(dev);
-
- mutex_lock(&ts->mutex);
-
- if (ts->suspended && ts->opened)
- __tsc2005_enable(ts);
-
- ts->suspended = false;
-
- mutex_unlock(&ts->mutex);
-
- return 0;
+ return tsc200x_remove(&spi->dev);
}
-static SIMPLE_DEV_PM_OPS(tsc2005_pm_ops, tsc2005_suspend, tsc2005_resume);
-
static struct spi_driver tsc2005_driver = {
.driver = {
.name = "tsc2005",
.owner = THIS_MODULE,
- .pm = &tsc2005_pm_ops,
+ .pm = &tsc200x_pm_ops,
},
.probe = tsc2005_probe,
.remove = tsc2005_remove,
@@ -761,7 +86,7 @@ static struct spi_driver tsc2005_driver = {
module_spi_driver(tsc2005_driver);
-MODULE_AUTHOR("Lauri Leukkunen <lauri.leukkunen@nokia.com>");
+MODULE_AUTHOR("Michael Welling <mwelling@ieee.org>");
MODULE_DESCRIPTION("TSC2005 Touchscreen Driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("spi:tsc2005");
similarity index 72%
copy from drivers/input/touchscreen/tsc2005.c
copy to drivers/input/touchscreen/tsc200x-core.c
@@ -1,7 +1,9 @@
/*
- * TSC2005 touchscreen driver
+ * TSC2004/TSC2005 touchscreen driver core
*
* Copyright (C) 2006-2010 Nokia Corporation
+ * Copyright (C) 2015 QWERTY Embedded Design
+ * Copyright (C) 2015 EMAC Inc.
*
* Author: Lauri Leukkunen <lauri.leukkunen@nokia.com>
* based on TSC2301 driver by Klaus K. Pedersen <klaus.k.pedersen@nokia.com>
@@ -15,11 +17,6 @@
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
*/
#include <linux/kernel.h>
@@ -30,11 +27,11 @@
#include <linux/delay.h>
#include <linux/pm.h>
#include <linux/of.h>
-#include <linux/spi/spi.h>
#include <linux/spi/tsc2005.h>
#include <linux/regulator/consumer.h>
#include <linux/regmap.h>
#include <linux/gpio/consumer.h>
+#include "tsc200x-core.h"
/*
* The touchscreen interface operates as follows:
@@ -43,7 +40,7 @@
* 2) TSC2005 performs AD conversion.
* 3) After the conversion is done TSC2005 drives DAV line down.
* 4) GPIO IRQ is received and tsc2005_irq_thread() is scheduled.
- * 5) tsc2005_irq_thread() queues up an spi transfer to fetch the x, y, z1, z2
+ * 5) tsc2005_irq_thread() queues up a transfer to fetch the x, y, z1, z2
* values.
* 6) tsc2005_irq_thread() reports coordinates to input layer and sets up
* tsc2005_penup_timer() to be called after TSC2005_PENUP_TIME_MS (40ms).
@@ -55,72 +52,6 @@
* watchdog is disabled.
*/
-/* control byte 1 */
-#define TSC2005_CMD 0x80
-#define TSC2005_CMD_NORMAL 0x00
-#define TSC2005_CMD_STOP 0x01
-#define TSC2005_CMD_12BIT 0x04
-
-/* control byte 0 */
-#define TSC2005_REG_READ 0x01 /* R/W access */
-#define TSC2005_REG_PND0 0x02 /* Power Not Down Control */
-#define TSC2005_REG_X (0x0 << 3)
-#define TSC2005_REG_Y (0x1 << 3)
-#define TSC2005_REG_Z1 (0x2 << 3)
-#define TSC2005_REG_Z2 (0x3 << 3)
-#define TSC2005_REG_AUX (0x4 << 3)
-#define TSC2005_REG_TEMP1 (0x5 << 3)
-#define TSC2005_REG_TEMP2 (0x6 << 3)
-#define TSC2005_REG_STATUS (0x7 << 3)
-#define TSC2005_REG_AUX_HIGH (0x8 << 3)
-#define TSC2005_REG_AUX_LOW (0x9 << 3)
-#define TSC2005_REG_TEMP_HIGH (0xA << 3)
-#define TSC2005_REG_TEMP_LOW (0xB << 3)
-#define TSC2005_REG_CFR0 (0xC << 3)
-#define TSC2005_REG_CFR1 (0xD << 3)
-#define TSC2005_REG_CFR2 (0xE << 3)
-#define TSC2005_REG_CONV_FUNC (0xF << 3)
-
-/* configuration register 0 */
-#define TSC2005_CFR0_PRECHARGE_276US 0x0040
-#define TSC2005_CFR0_STABTIME_1MS 0x0300
-#define TSC2005_CFR0_CLOCK_1MHZ 0x1000
-#define TSC2005_CFR0_RESOLUTION12 0x2000
-#define TSC2005_CFR0_PENMODE 0x8000
-#define TSC2005_CFR0_INITVALUE (TSC2005_CFR0_STABTIME_1MS | \
- TSC2005_CFR0_CLOCK_1MHZ | \
- TSC2005_CFR0_RESOLUTION12 | \
- TSC2005_CFR0_PRECHARGE_276US | \
- TSC2005_CFR0_PENMODE)
-
-/* bits common to both read and write of configuration register 0 */
-#define TSC2005_CFR0_RW_MASK 0x3fff
-
-/* configuration register 1 */
-#define TSC2005_CFR1_BATCHDELAY_4MS 0x0003
-#define TSC2005_CFR1_INITVALUE TSC2005_CFR1_BATCHDELAY_4MS
-
-/* configuration register 2 */
-#define TSC2005_CFR2_MAVE_Z 0x0004
-#define TSC2005_CFR2_MAVE_Y 0x0008
-#define TSC2005_CFR2_MAVE_X 0x0010
-#define TSC2005_CFR2_AVG_7 0x0800
-#define TSC2005_CFR2_MEDIUM_15 0x3000
-#define TSC2005_CFR2_INITVALUE (TSC2005_CFR2_MAVE_X | \
- TSC2005_CFR2_MAVE_Y | \
- TSC2005_CFR2_MAVE_Z | \
- TSC2005_CFR2_MEDIUM_15 | \
- TSC2005_CFR2_AVG_7)
-
-#define MAX_12BIT 0xfff
-#define TSC2005_DEF_X_FUZZ 4
-#define TSC2005_DEF_Y_FUZZ 8
-#define TSC2005_DEF_P_FUZZ 2
-#define TSC2005_DEF_RESISTOR 280
-
-#define TSC2005_SPI_MAX_SPEED_HZ 10000000
-#define TSC2005_PENUP_TIME_MS 40
-
static const struct regmap_range tsc2005_writable_ranges[] = {
regmap_reg_range(TSC2005_REG_AUX_HIGH, TSC2005_REG_CFR2),
};
@@ -130,7 +61,7 @@ static const struct regmap_access_table tsc2005_writable_table = {
.n_yes_ranges = ARRAY_SIZE(tsc2005_writable_ranges),
};
-static struct regmap_config tsc2005_regmap_config = {
+const struct regmap_config tsc200x_regmap_config = {
.reg_bits = 8,
.val_bits = 16,
.reg_stride = 0x08,
@@ -150,8 +81,9 @@ struct tsc2005_data {
#define TSC2005_DATA_REGS 4
struct tsc2005 {
- struct spi_device *spi;
+ struct device *dev;
struct regmap *regmap;
+ __u16 bustype;
struct input_dev *idev;
char phys[32];
@@ -182,32 +114,10 @@ struct tsc2005 {
struct gpio_desc *reset_gpio;
void (*set_reset)(bool enable);
+ int (*tsc200x_cmd)(struct device *dev, u8 cmd);
+ int irq;
};
-static int tsc2005_cmd(struct tsc2005 *ts, u8 cmd)
-{
- u8 tx = TSC2005_CMD | TSC2005_CMD_12BIT | cmd;
- struct spi_transfer xfer = {
- .tx_buf = &tx,
- .len = 1,
- .bits_per_word = 8,
- };
- struct spi_message msg;
- int error;
-
- spi_message_init(&msg);
- spi_message_add_tail(&xfer, &msg);
-
- error = spi_sync(ts->spi, &msg);
- if (error) {
- dev_err(&ts->spi->dev, "%s: failed, command: %x, error: %d\n",
- __func__, cmd, error);
- return error;
- }
-
- return 0;
-}
-
static void tsc2005_update_pen_state(struct tsc2005 *ts,
int x, int y, int pressure)
{
@@ -227,7 +137,7 @@ static void tsc2005_update_pen_state(struct tsc2005 *ts,
}
}
input_sync(ts->idev);
- dev_dbg(&ts->spi->dev, "point(%4d,%4d), pressure (%4d)\n", x, y,
+ dev_dbg(ts->dev, "point(%4d,%4d), pressure (%4d)\n", x, y,
pressure);
}
@@ -308,12 +218,12 @@ static void tsc2005_start_scan(struct tsc2005 *ts)
regmap_write(ts->regmap, TSC2005_REG_CFR0, TSC2005_CFR0_INITVALUE);
regmap_write(ts->regmap, TSC2005_REG_CFR1, TSC2005_CFR1_INITVALUE);
regmap_write(ts->regmap, TSC2005_REG_CFR2, TSC2005_CFR2_INITVALUE);
- tsc2005_cmd(ts, TSC2005_CMD_NORMAL);
+ ts->tsc200x_cmd(ts->dev, TSC2005_CMD_NORMAL);
}
static void tsc2005_stop_scan(struct tsc2005 *ts)
{
- tsc2005_cmd(ts, TSC2005_CMD_STOP);
+ ts->tsc200x_cmd(ts->dev, TSC2005_CMD_STOP);
}
static void tsc2005_set_reset(struct tsc2005 *ts, bool enable)
@@ -329,12 +239,12 @@ static void __tsc2005_disable(struct tsc2005 *ts)
{
tsc2005_stop_scan(ts);
- disable_irq(ts->spi->irq);
+ disable_irq(ts->irq);
del_timer_sync(&ts->penup_timer);
cancel_delayed_work_sync(&ts->esd_work);
- enable_irq(ts->spi->irq);
+ enable_irq(ts->irq);
}
/* must be called with ts->mutex held */
@@ -487,9 +397,9 @@ static void tsc2005_esd_work(struct work_struct *work)
* then we should reset the controller as if from power-up and start
* scanning again.
*/
- dev_info(&ts->spi->dev, "TSC2005 not responding - resetting\n");
+ dev_info(ts->dev, "TSC2005 not responding - resetting\n");
- disable_irq(ts->spi->irq);
+ disable_irq(ts->irq);
del_timer_sync(&ts->penup_timer);
tsc2005_update_pen_state(ts, 0, 0, 0);
@@ -498,7 +408,7 @@ static void tsc2005_esd_work(struct work_struct *work)
usleep_range(100, 500); /* only 10us required */
tsc2005_set_reset(ts, true);
- enable_irq(ts->spi->irq);
+ enable_irq(ts->irq);
tsc2005_start_scan(ts);
out:
@@ -540,10 +450,12 @@ static void tsc2005_close(struct input_dev *input)
mutex_unlock(&ts->mutex);
}
-static int tsc2005_probe(struct spi_device *spi)
+int tsc200x_probe(struct device *dev, int irq, __u16 bustype,
+ struct regmap *regmap,
+ int (*tsc200x_cmd)(struct device *dev, u8 cmd))
{
- const struct tsc2005_platform_data *pdata = dev_get_platdata(&spi->dev);
- struct device_node *np = spi->dev.of_node;
+ const struct tsc2005_platform_data *pdata = dev_get_platdata(dev);
+ struct device_node *np = dev->of_node;
struct tsc2005 *ts;
struct input_dev *input_dev;
@@ -558,12 +470,20 @@ static int tsc2005_probe(struct spi_device *spi)
int error;
if (!np && !pdata) {
- dev_err(&spi->dev, "no platform data\n");
+ dev_err(dev, "no platform data\n");
return -ENODEV;
}
- if (spi->irq <= 0) {
- dev_err(&spi->dev, "no irq\n");
+ if (irq <= 0) {
+ dev_err(dev, "no irq\n");
+ return -ENODEV;
+ }
+
+ if (IS_ERR(regmap))
+ return PTR_ERR(regmap);
+
+ if (!tsc200x_cmd) {
+ dev_err(dev, "no cmd function\n");
return -ENODEV;
}
@@ -584,45 +504,33 @@ static int tsc2005_probe(struct spi_device *spi)
&esd_timeout);
}
- spi->mode = SPI_MODE_0;
- spi->bits_per_word = 8;
- if (!spi->max_speed_hz)
- spi->max_speed_hz = TSC2005_SPI_MAX_SPEED_HZ;
-
- error = spi_setup(spi);
- if (error)
- return error;
-
- ts = devm_kzalloc(&spi->dev, sizeof(*ts), GFP_KERNEL);
+ ts = devm_kzalloc(dev, sizeof(*ts), GFP_KERNEL);
if (!ts)
return -ENOMEM;
- input_dev = devm_input_allocate_device(&spi->dev);
+ input_dev = devm_input_allocate_device(dev);
if (!input_dev)
return -ENOMEM;
- ts->spi = spi;
+ ts->irq = irq;
+ ts->dev = dev;
ts->idev = input_dev;
-
- ts->regmap = devm_regmap_init_spi(spi, &tsc2005_regmap_config);
- if (IS_ERR(ts->regmap))
- return PTR_ERR(ts->regmap);
-
+ ts->regmap = regmap;
+ ts->tsc200x_cmd = tsc200x_cmd;
ts->x_plate_ohm = x_plate_ohm;
ts->esd_timeout = esd_timeout;
- ts->reset_gpio = devm_gpiod_get_optional(&spi->dev, "reset",
- GPIOD_OUT_HIGH);
+ ts->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
if (IS_ERR(ts->reset_gpio)) {
error = PTR_ERR(ts->reset_gpio);
- dev_err(&spi->dev, "error acquiring reset gpio: %d\n", error);
+ dev_err(dev, "error acquiring reset gpio: %d\n", error);
return error;
}
- ts->vio = devm_regulator_get_optional(&spi->dev, "vio");
+ ts->vio = devm_regulator_get_optional(dev, "vio");
if (IS_ERR(ts->vio)) {
error = PTR_ERR(ts->vio);
- dev_err(&spi->dev, "vio regulator missing (%d)", error);
+ dev_err(dev, "vio regulator missing (%d)", error);
return error;
}
@@ -637,12 +545,12 @@ static int tsc2005_probe(struct spi_device *spi)
INIT_DELAYED_WORK(&ts->esd_work, tsc2005_esd_work);
snprintf(ts->phys, sizeof(ts->phys),
- "%s/input-ts", dev_name(&spi->dev));
+ "%s/input-ts", dev_name(dev));
input_dev->name = "TSC2005 touchscreen";
input_dev->phys = ts->phys;
- input_dev->id.bustype = BUS_SPI;
- input_dev->dev.parent = &spi->dev;
+ input_dev->id.bustype = bustype;
+ input_dev->dev.parent = dev;
input_dev->evbit[0] = BIT(EV_ABS) | BIT(EV_KEY);
input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
@@ -661,12 +569,12 @@ static int tsc2005_probe(struct spi_device *spi)
/* Ensure the touchscreen is off */
tsc2005_stop_scan(ts);
- error = devm_request_threaded_irq(&spi->dev, spi->irq, NULL,
+ error = devm_request_threaded_irq(dev, irq, NULL,
tsc2005_irq_thread,
IRQF_TRIGGER_RISING | IRQF_ONESHOT,
"tsc2005", ts);
if (error) {
- dev_err(&spi->dev, "Failed to request irq, err: %d\n", error);
+ dev_err(dev, "Failed to request irq, err: %d\n", error);
return error;
}
@@ -677,43 +585,45 @@ static int tsc2005_probe(struct spi_device *spi)
return error;
}
- dev_set_drvdata(&spi->dev, ts);
- error = sysfs_create_group(&spi->dev.kobj, &tsc2005_attr_group);
+ dev_set_drvdata(dev, ts);
+ error = sysfs_create_group(&dev->kobj, &tsc2005_attr_group);
if (error) {
- dev_err(&spi->dev,
+ dev_err(dev,
"Failed to create sysfs attributes, err: %d\n", error);
goto disable_regulator;
}
error = input_register_device(ts->idev);
if (error) {
- dev_err(&spi->dev,
+ dev_err(dev,
"Failed to register input device, err: %d\n", error);
goto err_remove_sysfs;
}
- irq_set_irq_wake(spi->irq, 1);
+ irq_set_irq_wake(irq, 1);
return 0;
err_remove_sysfs:
- sysfs_remove_group(&spi->dev.kobj, &tsc2005_attr_group);
+ sysfs_remove_group(&dev->kobj, &tsc2005_attr_group);
disable_regulator:
if (ts->vio)
regulator_disable(ts->vio);
return error;
}
+EXPORT_SYMBOL_GPL(tsc200x_probe);
-static int tsc2005_remove(struct spi_device *spi)
+int tsc200x_remove(struct device *dev)
{
- struct tsc2005 *ts = dev_get_drvdata(&spi->dev);
+ struct tsc2005 *ts = dev_get_drvdata(dev);
- sysfs_remove_group(&spi->dev.kobj, &tsc2005_attr_group);
+ sysfs_remove_group(&dev->kobj, &tsc2005_attr_group);
if (ts->vio)
regulator_disable(ts->vio);
return 0;
}
+EXPORT_SYMBOL_GPL(tsc200x_remove);
static int __maybe_unused tsc2005_suspend(struct device *dev)
{
@@ -747,21 +657,9 @@ static int __maybe_unused tsc2005_resume(struct device *dev)
return 0;
}
-static SIMPLE_DEV_PM_OPS(tsc2005_pm_ops, tsc2005_suspend, tsc2005_resume);
-
-static struct spi_driver tsc2005_driver = {
- .driver = {
- .name = "tsc2005",
- .owner = THIS_MODULE,
- .pm = &tsc2005_pm_ops,
- },
- .probe = tsc2005_probe,
- .remove = tsc2005_remove,
-};
-
-module_spi_driver(tsc2005_driver);
+SIMPLE_DEV_PM_OPS(tsc200x_pm_ops, tsc2005_suspend, tsc2005_resume);
+EXPORT_SYMBOL_GPL(tsc200x_pm_ops);
MODULE_AUTHOR("Lauri Leukkunen <lauri.leukkunen@nokia.com>");
MODULE_DESCRIPTION("TSC2005 Touchscreen Driver");
MODULE_LICENSE("GPL");
-MODULE_ALIAS("spi:tsc2005");
new file mode 100644
@@ -0,0 +1,78 @@
+#ifndef _TSC200X_CORE_H
+#define _TSC200X_CORE_H
+
+/* control byte 1 */
+#define TSC2005_CMD 0x80
+#define TSC2005_CMD_NORMAL 0x00
+#define TSC2005_CMD_STOP 0x01
+#define TSC2005_CMD_12BIT 0x04
+
+/* control byte 0 */
+#define TSC2005_REG_READ 0x01 /* R/W access */
+#define TSC2005_REG_PND0 0x02 /* Power Not Down Control */
+#define TSC2005_REG_X (0x0 << 3)
+#define TSC2005_REG_Y (0x1 << 3)
+#define TSC2005_REG_Z1 (0x2 << 3)
+#define TSC2005_REG_Z2 (0x3 << 3)
+#define TSC2005_REG_AUX (0x4 << 3)
+#define TSC2005_REG_TEMP1 (0x5 << 3)
+#define TSC2005_REG_TEMP2 (0x6 << 3)
+#define TSC2005_REG_STATUS (0x7 << 3)
+#define TSC2005_REG_AUX_HIGH (0x8 << 3)
+#define TSC2005_REG_AUX_LOW (0x9 << 3)
+#define TSC2005_REG_TEMP_HIGH (0xA << 3)
+#define TSC2005_REG_TEMP_LOW (0xB << 3)
+#define TSC2005_REG_CFR0 (0xC << 3)
+#define TSC2005_REG_CFR1 (0xD << 3)
+#define TSC2005_REG_CFR2 (0xE << 3)
+#define TSC2005_REG_CONV_FUNC (0xF << 3)
+
+/* configuration register 0 */
+#define TSC2005_CFR0_PRECHARGE_276US 0x0040
+#define TSC2005_CFR0_STABTIME_1MS 0x0300
+#define TSC2005_CFR0_CLOCK_1MHZ 0x1000
+#define TSC2005_CFR0_RESOLUTION12 0x2000
+#define TSC2005_CFR0_PENMODE 0x8000
+#define TSC2005_CFR0_INITVALUE (TSC2005_CFR0_STABTIME_1MS | \
+ TSC2005_CFR0_CLOCK_1MHZ | \
+ TSC2005_CFR0_RESOLUTION12 | \
+ TSC2005_CFR0_PRECHARGE_276US | \
+ TSC2005_CFR0_PENMODE)
+
+/* bits common to both read and write of configuration register 0 */
+#define TSC2005_CFR0_RW_MASK 0x3fff
+
+/* configuration register 1 */
+#define TSC2005_CFR1_BATCHDELAY_4MS 0x0003
+#define TSC2005_CFR1_INITVALUE TSC2005_CFR1_BATCHDELAY_4MS
+
+/* configuration register 2 */
+#define TSC2005_CFR2_MAVE_Z 0x0004
+#define TSC2005_CFR2_MAVE_Y 0x0008
+#define TSC2005_CFR2_MAVE_X 0x0010
+#define TSC2005_CFR2_AVG_7 0x0800
+#define TSC2005_CFR2_MEDIUM_15 0x3000
+#define TSC2005_CFR2_INITVALUE (TSC2005_CFR2_MAVE_X | \
+ TSC2005_CFR2_MAVE_Y | \
+ TSC2005_CFR2_MAVE_Z | \
+ TSC2005_CFR2_MEDIUM_15 | \
+ TSC2005_CFR2_AVG_7)
+
+#define MAX_12BIT 0xfff
+#define TSC2005_DEF_X_FUZZ 4
+#define TSC2005_DEF_Y_FUZZ 8
+#define TSC2005_DEF_P_FUZZ 2
+#define TSC2005_DEF_RESISTOR 280
+
+#define TSC2005_SPI_MAX_SPEED_HZ 10000000
+#define TSC2005_PENUP_TIME_MS 40
+
+extern const struct regmap_config tsc200x_regmap_config;
+extern const struct dev_pm_ops tsc200x_pm_ops;
+
+int tsc200x_probe(struct device *dev, int irq, __u16 bustype,
+ struct regmap *regmap,
+ int (*tsc200x_cmd)(struct device *dev, u8 cmd));
+int tsc200x_remove(struct device *dev);
+
+#endif
This patch separates the SPI functionality from core functionality that overlaps with the tsc2004. Prepares kernel for new tsc2004 driver without much redundant code. Signed-off-by: Michael Welling <mwelling@ieee.org> --- drivers/input/touchscreen/Kconfig | 4 + drivers/input/touchscreen/Makefile | 1 + drivers/input/touchscreen/tsc2005.c | 709 +-------------------- .../touchscreen/{tsc2005.c => tsc200x-core.c} | 226 ++----- drivers/input/touchscreen/tsc200x-core.h | 78 +++ 5 files changed, 162 insertions(+), 856 deletions(-) copy drivers/input/touchscreen/{tsc2005.c => tsc200x-core.c} (72%) create mode 100644 drivers/input/touchscreen/tsc200x-core.h