new file mode 100644
@@ -0,0 +1,80 @@
+Azoteq IQS550/572/525 Trackpad/Touchscreen Controller
+
+Required properties:
+
+- compatible : Must be equal to one of the following:
+ "azoteq,iqs550"
+ "azoteq,iqs572"
+ "azoteq,iqs525"
+
+- reg : I2C slave address for the device.
+
+- interrupts : GPIO to which the device's active-high RDY
+ output is connected (see [0]).
+
+- reset-gpios : GPIO to which the device's active-low NRST
+ input is connected (see [1]).
+
+Optional properties:
+
+- touchscreen-min-x : See [2].
+
+- touchscreen-min-y : See [2].
+
+- touchscreen-size-x : See [2]. If this property is omitted, the
+ maximum x-coordinate is specified by the
+ device's "X Resolution" register.
+
+- touchscreen-size-y : See [2]. If this property is omitted, the
+ maximum y-coordinate is specified by the
+ device's "Y Resolution" register.
+
+- touchscreen-max-pressure : See [2]. Pressure is expressed as the sum of
+ the deltas across all channels impacted by a
+ touch event. A channel's delta is calculated
+ as its count value minus a reference, where
+ the count value is inversely proportional to
+ the channel's capacitance.
+
+- touchscreen-fuzz-x : See [2].
+
+- touchscreen-fuzz-y : See [2].
+
+- touchscreen-fuzz-pressure : See [2].
+
+- touchscreen-inverted-x : See [2]. Inversion is applied relative to that
+ which may already be specified by the device's
+ FLIP_X and FLIP_Y register fields.
+
+- touchscreen-inverted-y : See [2]. Inversion is applied relative to that
+ which may already be specified by the device's
+ FLIP_X and FLIP_Y register fields.
+
+- touchscreen-swapped-x-y : See [2]. Swapping is applied relative to that
+ which may already be specified by the device's
+ SWITCH_XY_AXIS register field.
+
+[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+[1]: Documentation/devicetree/bindings/gpio/gpio.txt
+[2]: Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt
+
+Example:
+
+ &i2c1 {
+ /* ... */
+
+ touchscreen@74 {
+ compatible = "azoteq,iqs550";
+ reg = <0x74>;
+ interrupt-parent = <&gpio>;
+ interrupts = <17 4>;
+ reset-gpios = <&gpio 27 1>;
+
+ touchscreen-size-x = <640>;
+ touchscreen-size-y = <480>;
+
+ touchscreen-max-pressure = <16000>;
+ };
+
+ /* ... */
+ };
@@ -53,6 +53,7 @@ avic Shanghai AVIC Optoelectronics Co., Ltd.
avnet Avnet, Inc.
axentia Axentia Technologies AB
axis Axis Communications AB
+azoteq Azoteq (Pty) Ltd
bananapi BIPAI KEJI LIMITED
bhf Beckhoff Automation GmbH & Co. KG
bitmain Bitmain Technologies
This patch adds binding documentation for the Azoteq IQS550/572/525 family of trackpad/touchscreen controllers. Signed-off-by: Jeff LaBundy <jeff@labundy.com> --- Changes in v9: - Corrected the polarity of the reset GPIO in the example node to match that of the device's active-low NRST pin - Removed previous Reviewed-by trailer as this file has since changed Changes in v8: - Added Reviewed-by trailer Changes in v7: - Removed the azoteq,exp-ver-major and azoteq,exp-ver-minor properties to match the driver's updated device identification scheme - Updated the example node to use a level-sensitive interrupt rather than an edge-sensitive interrupt - Removed previous Reviewed-by trailer as this file has since changed Changes in v6: - None Changes in v5: - None Changes in v4: - None Changes in v3: - Added Reviewed-by trailer Changes in v2: - Separated each valid "compatible" property with a line break - Specified the polarity of the RDY and NRST pins - Replaced duplicate definitions of common touchscreen properties with a reference to touchscreen.txt - Specified the example node as "touchscreen@74" .../bindings/input/touchscreen/iqs5xx.txt | 80 ++++++++++++++++++++++ .../devicetree/bindings/vendor-prefixes.txt | 1 + 2 files changed, 81 insertions(+) create mode 100644 Documentation/devicetree/bindings/input/touchscreen/iqs5xx.txt -- 2.7.4