| Message ID | 1579581860-29560-1-git-send-email-gupt21@gmail.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [v2] HID: mcp2221: add usb to i2c-smbus host bridge driver | expand |
Hi Rishi, On Tue, Jan 21, 2020 at 2:44 PM Rishi Gupta <gupt21@gmail.com> wrote: > > MCP2221 is a USB HID to I2C/SMbus host bridge device. This > commit implements i2c and smbus host adapter support. 7-bit > address and i2c multi-message transaction is also supported. > > Signed-off-by: Rishi Gupta <gupt21@gmail.com> > --- Thanks for the driver. Well, this is not a full review, but a few things jumped to my mind when scheming through this patch. Comments inlined > > Changes in v2: > * added myself in MAINTAINERS for this driver > * use macro from hid-ids.h for usb vid and pid > * optimize mcp_i2c_write() - less coding > * correctly set data length in smbus transaction hid report > * added static keyword before int mcp_smbus_xfer() > * replace references to silicon labs with microchip > > Only smbus block/proc is not tested due to lack of appropriate > hardware. Rest all is fully tested. > > MAINTAINERS | 7 + > drivers/hid/Kconfig | 10 + > drivers/hid/Makefile | 1 + > drivers/hid/hid-ids.h | 1 + > drivers/hid/hid-mcp2221.c | 756 ++++++++++++++++++++++++++++++++++++++++++++++ > drivers/hid/hid-quirks.c | 3 + > 6 files changed, 778 insertions(+) > create mode 100644 drivers/hid/hid-mcp2221.c > > diff --git a/MAINTAINERS b/MAINTAINERS > index cf6ccca..bc392c7 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -10121,6 +10121,13 @@ F: drivers/net/can/m_can/m_can.c > F: drivers/net/can/m_can/m_can.h > F: drivers/net/can/m_can/m_can_platform.c > > +MCP2221A MICROCHIP USB TO I2C BRIDGE DRIVER > +M: Rishi Gupta <gupt21@gmail.com> > +L: linux-i2c@vger.kernel.org > +L: linux-input@vger.kernel.org > +S: Maintained > +F: drivers/hid/hid-mcp2221.c > + > MCP4018 AND MCP4531 MICROCHIP DIGITAL POTENTIOMETER DRIVERS > M: Peter Rosin <peda@axentia.se> > L: linux-iio@vger.kernel.org > diff --git a/drivers/hid/Kconfig b/drivers/hid/Kconfig > index 494a39e..08a2522 100644 > --- a/drivers/hid/Kconfig > +++ b/drivers/hid/Kconfig > @@ -1145,6 +1145,16 @@ config HID_ALPS > Say Y here if you have a Alps touchpads over i2c-hid or usbhid > and want support for its special functionalities. > > +config HID_MCP2221 > + tristate "Microchip MCP2221 HID USB-to-I2C/SMbus host support" > + depends on USB_HID && HIDRAW && I2C There should not be a need for USB_HID at that point (see below) > + ---help--- > + Provides I2C host adapter functionality over USB through MCP2221 AFAICT, only SMBus is provided. Can you export full I2C communication? > + from Microchip. I2C bus speed can be set during driver loading. This *feels* wrong. Is that something common enough when loading I2C adapters? > + > + To compile this driver as a module, choose M here: the module > + will be called hid-mcp2221.ko. > + > endmenu > > endif # HID > diff --git a/drivers/hid/Makefile b/drivers/hid/Makefile > index bfefa36..567a241 100644 > --- a/drivers/hid/Makefile > +++ b/drivers/hid/Makefile > @@ -71,6 +71,7 @@ obj-$(CONFIG_HID_MACALLY) += hid-macally.o > obj-$(CONFIG_HID_MAGICMOUSE) += hid-magicmouse.o > obj-$(CONFIG_HID_MALTRON) += hid-maltron.o > obj-$(CONFIG_HID_MAYFLASH) += hid-mf.o > +obj-$(CONFIG_HID_MCP2221) += hid-mcp2221.o > obj-$(CONFIG_HID_MICROSOFT) += hid-microsoft.o > obj-$(CONFIG_HID_MONTEREY) += hid-monterey.o > obj-$(CONFIG_HID_MULTITOUCH) += hid-multitouch.o > diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h > index 3a400ce..53236ac 100644 > --- a/drivers/hid/hid-ids.h > +++ b/drivers/hid/hid-ids.h > @@ -819,6 +819,7 @@ > #define USB_DEVICE_ID_PICK16F1454 0x0042 > #define USB_DEVICE_ID_PICK16F1454_V2 0xf2f7 > #define USB_DEVICE_ID_LUXAFOR 0xf372 > +#define USB_DEVICE_ID_MCP2221 0x00dd > > #define USB_VENDOR_ID_MICROSOFT 0x045e > #define USB_DEVICE_ID_SIDEWINDER_GV 0x003b > diff --git a/drivers/hid/hid-mcp2221.c b/drivers/hid/hid-mcp2221.c > new file mode 100644 > index 0000000..5035f1e > --- /dev/null > +++ b/drivers/hid/hid-mcp2221.c > @@ -0,0 +1,756 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* > + * MCP2221A - Microchip USB to I2C Host Protocol Bridge > + * > + * Copyright (c) 2019, Rishi Gupta <gupt21@gmail.com> > + * > + * Datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/20005565B.pdf > + */ > + > +#include <linux/module.h> > +#include <linux/err.h> > +#include <linux/mutex.h> > +#include <linux/completion.h> > +#include <linux/delay.h> > +#include <linux/hid.h> > +#include <linux/usb.h> This is generally a big "NO" from me. We can actually emulate devices through uhid.ko, and this is a security hole to randomly access USB commands on a device emulated by uhid. There is a macro or function that we can use to check if the device is actually using USB, but this is only useful when the device is not fully HID compatible and needs to send USB urbs directly. This is not the case here, so we should remove that line. > +#include <linux/i2c.h> > +#include "hid-ids.h" > + > +/* Commands codes in a raw output report */ > +#define MCP2221_I2C_WR_DATA 0x90 > +#define MCP2221_I2C_WR_NO_STOP 0x94 > +#define MCP2221_I2C_RD_DATA 0x91 > +#define MCP2221_I2C_RD_RPT_START 0x93 > +#define MCP2221_I2C_GET_DATA 0x40 > +#define MCP2221_I2C_PARAM_OR_STATUS 0x10 > +#define MCP2221_I2C_SET_SPEED 0x20 > +#define MCP2221_I2C_CANCEL 0x10 hid-cp2112.c, a similar driver, uses enums here. It would make sense to use enums as well (and for the rest of the defines). > + > +/* Response codes in a raw input report */ > +#define MCP2221_SUCCESS 0x00 > +#define MCP2221_I2C_ENG_BUSY 0x01 > +#define MCP2221_I2C_START_TOUT 0x12 > +#define MCP2221_I2C_STOP_TOUT 0x62 > +#define MCP2221_I2C_WRADDRL_TOUT 0x23 > +#define MCP2221_I2C_WRDATA_TOUT 0x44 > +#define MCP2221_I2C_WRADDRL_NACK 0x25 > +#define MCP2221_I2C_MASK_ADDR_NACK 0x40 > +#define MCP2221_I2C_WRADDRL_SEND 0x21 > +#define MCP2221_I2C_ADDR_NACK 0x25 > +#define MCP2221_I2C_READ_COMPL 0x55 > + > +/* > + * There is no way to distinguish responses. Therefore next command > + * is sent only after response to previous has been received. Mutex > + * lock is used for this purpose mainly. > + */ > +struct mcp2221 { > + struct hid_device *hdev; > + struct i2c_adapter adapter; > + struct mutex lock; > + struct completion wait_in_report; > + u8 *rxbuf; > + u8 txbuf[64]; > + int rxbuf_idx; > + int status; > + u8 cur_i2c_clk_div; > +}; > + > +/* > + * Default i2c bus clock frequency in kHz. Override through > + * module param if required. > + */ Again, this feels wrong to me. I need to be convinced. > +static uint i2c_clk_freq = 400; > + > +/* Synchronously send output report to the device */ > +static int mcp_send_report(struct mcp2221 *mcp, > + u8 *out_report, size_t len) > +{ > + u8 *buf; > + int ret; > + > + buf = kmemdup(out_report, len, GFP_KERNEL); > + if (!buf) > + return -ENOMEM; > + > + /* mcp2221 uses interrupt endpoint for out reports */ > + ret = hid_hw_output_report(mcp->hdev, buf, len); > + kfree(buf); > + > + if (ret < 0) > + return ret; > + return 0; > +} > + > +/* > + * Send o/p report to the device and wait for i/p report to be > + * received from the device. If the device does not respond, > + * we timeout. > + */ > +static int mcp_send_data_req_status(struct mcp2221 *mcp, > + u8 *out_report, int len) > +{ > + int ret; > + unsigned long t; > + > + reinit_completion(&mcp->wait_in_report); > + > + ret = mcp_send_report(mcp, out_report, len); > + if (ret) > + return ret; > + > + t = wait_for_completion_timeout(&mcp->wait_in_report, > + msecs_to_jiffies(4000)); > + if (!t) > + return -ETIMEDOUT; > + > + return mcp->status; > +} > + > +/* Check pass/fail for actual communication with i2c slave */ > +static int mcp_chk_last_cmd_status(struct mcp2221 *mcp) > +{ > + int x; > + > + mcp->txbuf[0] = MCP2221_I2C_PARAM_OR_STATUS; > + > + for (x = 1; x < 8; x++) > + mcp->txbuf[x] = 0; You should probably use memset instead. > + > + return mcp_send_data_req_status(mcp, mcp->txbuf, 8); > +} > + > +/* Cancels last command releasing i2c bus just in case occupied */ > +static int mcp_cancel_last_cmd(struct mcp2221 *mcp) > +{ > + int x; > + > + mcp->txbuf[0] = MCP2221_I2C_PARAM_OR_STATUS; > + mcp->txbuf[1] = 0; > + mcp->txbuf[2] = MCP2221_I2C_CANCEL; > + > + for (x = 3; x < 8; x++) > + mcp->txbuf[x] = 0; memset too here > + > + return mcp_send_data_req_status(mcp, mcp->txbuf, 8); > +} > + > +static int mcp_set_i2c_speed(struct mcp2221 *mcp) > +{ > + int ret; > + > + mcp->txbuf[0] = MCP2221_I2C_PARAM_OR_STATUS; > + mcp->txbuf[1] = 0; > + mcp->txbuf[2] = 0; > + mcp->txbuf[3] = MCP2221_I2C_SET_SPEED; > + mcp->txbuf[4] = mcp->cur_i2c_clk_div; > + mcp->txbuf[5] = 0; > + mcp->txbuf[6] = 0; > + mcp->txbuf[7] = 0; memset and then assign the non null value fields. > + > + ret = mcp_send_data_req_status(mcp, mcp->txbuf, 8); > + if (ret) { > + /* Small delay is needed here */ > + usleep_range(980, 1000); > + mcp_cancel_last_cmd(mcp); > + } > + > + return 0; > +} > + > +/* > + * An output report can contain minimum 1 and maximum 60 user data > + * bytes. If the number of data bytes is more then 60, we send it > + * in chunks of 60 bytes. Last chunk may contain exactly 60 or less > + * bytes. Total number of bytes is informed in very first report to > + * mcp2221, from that point onwards it first collect all the data > + * from host and then send to i2c slave device. > + */ > +static int mcp_i2c_write(struct mcp2221 *mcp, > + struct i2c_msg *msg, int type, u8 last_status) > +{ > + int ret, len, idx, sent; > + > + idx = 0; > + sent = 0; > + if (msg->len < 60) > + len = msg->len; > + else > + len = 60; > + > + do { > + mcp->txbuf[0] = type; > + mcp->txbuf[1] = msg->len & 0xff; > + mcp->txbuf[2] = msg->len >> 8; > + mcp->txbuf[3] = (u8)(msg->addr << 1); > + > + memcpy(&mcp->txbuf[4], &msg->buf[idx], len); > + > + ret = mcp_send_data_req_status(mcp, mcp->txbuf, len + 4); > + if (ret) > + return ret; > + > + usleep_range(980, 1000); > + > + ret = mcp_chk_last_cmd_status(mcp); > + if (ret) > + return ret; > + > + sent = sent + len; > + if (sent >= msg->len) > + break; > + > + idx = idx + len; > + if ((msg->len - sent) < 60) > + len = msg->len - sent; > + else > + len = 60; > + > + /* > + * Testing shows delay is needed between successive writes > + * otherwise next write fails on first-try from i2c core. > + * This value is obtained through automated stress testing. > + */ > + usleep_range(980, 1000); That is a lot a usleeps. Are you sure we have to, or can we just rely on the HID command completion? > + } while (len > 0); > + > + return ret; > +} > + > +/* > + * Device reads all data (0 - 65535 bytes) from i2c slave device and > + * stores it in device itself. This data is read back from device to > + * host in multiples of 60 bytes using input reports. > + */ > +static int mcp_i2c_smbus_read(struct mcp2221 *mcp, > + struct i2c_msg *msg, int type, u16 smbus_addr, > + u8 smbus_len, u8 *smbus_buf) > +{ > + int ret; > + u16 total_len; > + > + mcp->txbuf[0] = type; > + if (msg) { > + mcp->txbuf[1] = msg->len & 0xff; > + mcp->txbuf[2] = msg->len >> 8; > + mcp->txbuf[3] = (u8)(msg->addr << 1); > + total_len = msg->len; > + mcp->rxbuf = msg->buf; > + } else { > + mcp->txbuf[1] = smbus_len; > + mcp->txbuf[2] = 0; > + mcp->txbuf[3] = (u8)(smbus_addr << 1); > + total_len = smbus_len; > + mcp->rxbuf = smbus_buf; > + } > + > + ret = mcp_send_data_req_status(mcp, mcp->txbuf, 4); > + if (ret) > + return ret; > + > + mcp->rxbuf_idx = 0; > + > + do { > + mcp->txbuf[0] = MCP2221_I2C_GET_DATA; > + mcp->txbuf[1] = 0; > + mcp->txbuf[2] = 0; > + mcp->txbuf[3] = 0; please memset > + > + ret = mcp_send_data_req_status(mcp, mcp->txbuf, 1); > + if (ret) > + return ret; > + > + ret = mcp_chk_last_cmd_status(mcp); > + if (ret) > + return ret; > + > + usleep_range(980, 1000); > + } while (mcp->rxbuf_idx < total_len); > + > + return ret; > +} > + > +static int mcp_i2c_xfer(struct i2c_adapter *adapter, > + struct i2c_msg msgs[], int num) > +{ > + int ret; > + struct mcp2221 *mcp = i2c_get_adapdata(adapter); > + > + hid_hw_power(mcp->hdev, PM_HINT_FULLON); > + > + mutex_lock(&mcp->lock); > + > + /* Setting speed before every transaction is required for mcp2221 */ > + ret = mcp_set_i2c_speed(mcp); > + if (ret) > + goto exit; > + > + if (num == 1) { > + if (msgs->flags & I2C_M_RD) { > + ret = mcp_i2c_smbus_read(mcp, msgs, MCP2221_I2C_RD_DATA, > + 0, 0, NULL); > + } else { > + ret = mcp_i2c_write(mcp, msgs, MCP2221_I2C_WR_DATA, 1); > + } > + if (ret) > + goto exit; > + ret = num; > + } else if (num == 2) { > + /* Ex transaction; send reg address and read its contents */ > + if (msgs[0].addr == msgs[1].addr && > + !(msgs[0].flags & I2C_M_RD) && > + (msgs[1].flags & I2C_M_RD)) { > + > + ret = mcp_i2c_write(mcp, &msgs[0], > + MCP2221_I2C_WR_NO_STOP, 0); > + if (ret) > + goto exit; > + > + ret = mcp_i2c_smbus_read(mcp, &msgs[1], > + MCP2221_I2C_RD_RPT_START, > + 0, 0, NULL); > + if (ret) > + goto exit; > + ret = num; > + } else { > + dev_err(&adapter->dev, > + "unsupported i2c transaction size: %d\n", num); > + ret = -EOPNOTSUPP; > + } > + } else { > + dev_err(&adapter->dev, > + "unsupported i2c transaction size: %d\n", num); > + ret = -EOPNOTSUPP; > + } > + > +exit: > + hid_hw_power(mcp->hdev, PM_HINT_NORMAL); > + mutex_unlock(&mcp->lock); > + return ret; > +} > + > +static int mcp_smbus_write(struct mcp2221 *mcp, u16 addr, > + u8 command, u8 *buf, u8 len, int type, > + u8 last_status) > +{ > + int data_len, ret; > + > + mcp->txbuf[0] = type; > + mcp->txbuf[1] = len + 1; /* 1 is due to command byte itself */ > + mcp->txbuf[2] = 0; > + mcp->txbuf[3] = (u8)(addr << 1); > + mcp->txbuf[4] = command; > + > + switch (len) { > + case 0: > + data_len = 5; > + break; > + case 1: > + mcp->txbuf[5] = buf[0]; > + data_len = 6; > + break; > + case 2: > + mcp->txbuf[5] = buf[0]; > + mcp->txbuf[6] = buf[1]; > + data_len = 7; > + break; > + default: > + memcpy(&mcp->txbuf[5], buf, len); > + data_len = len + 5; > + } > + > + ret = mcp_send_data_req_status(mcp, mcp->txbuf, data_len); > + if (ret) > + return ret; > + > + if (last_status) { > + usleep_range(980, 1000); > + > + ret = mcp_chk_last_cmd_status(mcp); > + if (ret) > + return ret; > + } > + > + return ret; > +} > + > +static int mcp_smbus_xfer(struct i2c_adapter *adapter, u16 addr, > + unsigned short flags, char read_write, > + u8 command, int size, > + union i2c_smbus_data *data) > +{ > + int ret; > + struct mcp2221 *mcp = i2c_get_adapdata(adapter); > + > + hid_hw_power(mcp->hdev, PM_HINT_FULLON); > + > + mutex_lock(&mcp->lock); > + > + ret = mcp_set_i2c_speed(mcp); > + if (ret) > + goto exit; > + > + switch (size) { > + > + case I2C_SMBUS_QUICK: > + if (read_write == I2C_SMBUS_READ) > + ret = mcp_i2c_smbus_read(mcp, NULL, MCP2221_I2C_RD_DATA, > + addr, 0, &data->byte); > + else > + ret = mcp_smbus_write(mcp, addr, command, NULL, > + 0, MCP2221_I2C_WR_DATA, 1); > + break; > + case I2C_SMBUS_BYTE: > + if (read_write == I2C_SMBUS_READ) > + ret = mcp_i2c_smbus_read(mcp, NULL, MCP2221_I2C_RD_DATA, > + addr, 1, &data->byte); > + else > + ret = mcp_smbus_write(mcp, addr, command, NULL, > + 0, MCP2221_I2C_WR_DATA, 1); > + break; > + case I2C_SMBUS_BYTE_DATA: > + if (read_write == I2C_SMBUS_READ) { > + ret = mcp_smbus_write(mcp, addr, command, NULL, > + 0, MCP2221_I2C_WR_NO_STOP, 0); > + if (ret) > + goto exit; > + > + ret = mcp_i2c_smbus_read(mcp, NULL, > + MCP2221_I2C_RD_RPT_START, > + addr, 1, &data->byte); > + } else { > + ret = mcp_smbus_write(mcp, addr, command, &data->byte, > + 1, MCP2221_I2C_WR_DATA, 1); > + } > + break; > + case I2C_SMBUS_WORD_DATA: > + if (read_write == I2C_SMBUS_READ) { > + ret = mcp_smbus_write(mcp, addr, command, NULL, > + 0, MCP2221_I2C_WR_NO_STOP, 0); > + if (ret) > + goto exit; > + > + ret = mcp_i2c_smbus_read(mcp, NULL, > + MCP2221_I2C_RD_RPT_START, > + addr, 2, (u8 *)&data->word); > + } else { > + ret = mcp_smbus_write(mcp, addr, command, > + (u8 *)&data->word, 2, > + MCP2221_I2C_WR_DATA, 1); > + } > + break; > + case I2C_SMBUS_BLOCK_DATA: > + if (read_write == I2C_SMBUS_READ) { > + ret = mcp_smbus_write(mcp, addr, command, NULL, > + 0, MCP2221_I2C_WR_NO_STOP, 1); > + if (ret) > + goto exit; > + > + mcp->rxbuf_idx = 0; > + mcp->rxbuf = data->block; > + mcp->txbuf[0] = MCP2221_I2C_GET_DATA; > + ret = mcp_send_data_req_status(mcp, mcp->txbuf, 1); > + if (ret) > + goto exit; > + } else { > + if (!data->block[0]) { > + ret = -EINVAL; > + goto exit; > + } > + ret = mcp_smbus_write(mcp, addr, command, data->block, > + data->block[0] + 1, > + MCP2221_I2C_WR_DATA, 1); > + } > + break; > + case I2C_SMBUS_I2C_BLOCK_DATA: > + if (read_write == I2C_SMBUS_READ) { > + ret = mcp_smbus_write(mcp, addr, command, NULL, > + 0, MCP2221_I2C_WR_NO_STOP, 1); > + if (ret) > + goto exit; > + > + mcp->rxbuf_idx = 0; > + mcp->rxbuf = data->block; > + mcp->txbuf[0] = MCP2221_I2C_GET_DATA; > + ret = mcp_send_data_req_status(mcp, mcp->txbuf, 1); > + if (ret) > + goto exit; > + } else { > + if (!data->block[0]) { > + ret = -EINVAL; > + goto exit; > + } > + ret = mcp_smbus_write(mcp, addr, command, > + &data->block[1], data->block[0], > + MCP2221_I2C_WR_DATA, 1); > + } > + break; > + case I2C_SMBUS_PROC_CALL: > + ret = mcp_smbus_write(mcp, addr, command, > + (u8 *)&data->word, > + 2, MCP2221_I2C_WR_NO_STOP, 0); > + if (ret) > + goto exit; > + > + ret = mcp_i2c_smbus_read(mcp, NULL, > + MCP2221_I2C_RD_RPT_START, > + addr, 2, (u8 *)&data->word); > + break; > + case I2C_SMBUS_BLOCK_PROC_CALL: > + ret = mcp_smbus_write(mcp, addr, command, data->block, > + data->block[0] + 1, > + MCP2221_I2C_WR_NO_STOP, 0); > + if (ret) > + goto exit; > + > + ret = mcp_i2c_smbus_read(mcp, NULL, > + MCP2221_I2C_RD_RPT_START, > + addr, I2C_SMBUS_BLOCK_MAX, > + data->block); > + break; > + default: > + dev_err(&mcp->adapter.dev, > + "unsupported smbus transaction size:%d\n", size); > + ret = -EOPNOTSUPP; > + } > + > +exit: > + hid_hw_power(mcp->hdev, PM_HINT_NORMAL); > + mutex_unlock(&mcp->lock); > + return ret; > +} > + > +static u32 mcp_i2c_func(struct i2c_adapter *adapter) > +{ > + return I2C_FUNC_I2C | > + I2C_FUNC_SMBUS_READ_BLOCK_DATA | > + I2C_FUNC_SMBUS_BLOCK_PROC_CALL | > + (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_PEC); > +} > + > +static const struct i2c_algorithm mcp_i2c_algo = { > + .master_xfer = mcp_i2c_xfer, > + .smbus_xfer = mcp_smbus_xfer, > + .functionality = mcp_i2c_func, > +}; > + > +/* Gives current state of i2c engine inside mcp2221 */ > +static int mcp_get_i2c_eng_state(struct mcp2221 *mcp, > + u8 *data, u8 idx) > +{ > + int ret; > + > + switch (data[idx]) { > + case MCP2221_I2C_WRADDRL_NACK: > + case MCP2221_I2C_WRADDRL_SEND: > + ret = -ENXIO; > + break; > + case MCP2221_I2C_START_TOUT: > + case MCP2221_I2C_STOP_TOUT: > + case MCP2221_I2C_WRADDRL_TOUT: > + case MCP2221_I2C_WRDATA_TOUT: > + ret = -ETIMEDOUT; > + break; > + case MCP2221_I2C_ENG_BUSY: > + ret = -EAGAIN; > + break; > + case MCP2221_SUCCESS: > + ret = 0x00; > + break; > + default: > + ret = -EIO; > + } > + > + return ret; > +} > + > +/* > + * MCP2221 uses interrupt endpoint for input reports. This function > + * is called by HID layer when it receives i/p report from mcp2221, > + * which is actually a response to the previously sent command. > + * > + * MCP2221A firmware specific return codes are parsed and 0 or > + * appropriate negative error code is returned. Delayed response > + * results in timeout error and stray reponses results in -EIO. > + */ > +static int mcp2221_raw_event(struct hid_device *hdev, > + struct hid_report *report, u8 *data, int size) > +{ > + u8 *buf; > + struct mcp2221 *mcp = hid_get_drvdata(hdev); > + > + switch (data[0]) { > + > + case MCP2221_I2C_WR_DATA: > + case MCP2221_I2C_WR_NO_STOP: > + case MCP2221_I2C_RD_DATA: > + case MCP2221_I2C_RD_RPT_START: > + switch (data[1]) { > + case MCP2221_SUCCESS: > + mcp->status = 0; > + break; > + default: > + mcp->status = mcp_get_i2c_eng_state(mcp, data, 2); > + } > + complete(&mcp->wait_in_report); > + break; > + > + case MCP2221_I2C_PARAM_OR_STATUS: > + switch (data[1]) { > + case MCP2221_SUCCESS: > + if ((mcp->txbuf[3] == MCP2221_I2C_SET_SPEED) && > + (data[3] != MCP2221_I2C_SET_SPEED)) { > + mcp->status = -EAGAIN; > + break; > + } > + if (data[20] & MCP2221_I2C_MASK_ADDR_NACK) { > + mcp->status = -ENXIO; > + break; > + } > + mcp->status = mcp_get_i2c_eng_state(mcp, data, 8); > + break; > + default: > + mcp->status = -EIO; > + } > + complete(&mcp->wait_in_report); > + break; > + > + case MCP2221_I2C_GET_DATA: > + switch (data[1]) { > + case MCP2221_SUCCESS: > + if (data[2] == MCP2221_I2C_ADDR_NACK) { > + mcp->status = -ENXIO; > + break; > + } > + if (!mcp_get_i2c_eng_state(mcp, data, 2) > + && (data[3] == 0)) { > + mcp->status = 0; > + break; > + } > + if (data[3] == 127) { > + mcp->status = -EIO; > + break; > + } > + if (data[2] == MCP2221_I2C_READ_COMPL) { > + buf = mcp->rxbuf; > + memcpy(&buf[mcp->rxbuf_idx], &data[4], data[3]); > + mcp->rxbuf_idx = mcp->rxbuf_idx + data[3]; > + mcp->status = 0; > + break; > + } > + mcp->status = -EIO; > + break; > + default: > + mcp->status = -EIO; > + } > + complete(&mcp->wait_in_report); > + break; > + > + default: > + mcp->status = -EIO; > + complete(&mcp->wait_in_report); > + } > + > + return 1; > +} > + > +static int mcp2221_probe(struct hid_device *hdev, > + const struct hid_device_id *id) > +{ > + int ret; > + struct mcp2221 *mcp; > + struct usb_device *usd = to_usb_device(hdev->dev.parent->parent); You should ensure you are actually talking to a USB device. Otherwise, you are happily jumping to random addresses. But again, please drop any USB references. > + > + mcp = devm_kzalloc(&hdev->dev, sizeof(*mcp), GFP_KERNEL); > + if (!mcp) > + return -ENOMEM; > + > + ret = hid_parse(hdev); > + if (ret) { > + hid_err(hdev, "can't parse reports\n"); > + return ret; > + } > + > + ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT); > + if (ret) { > + hid_err(hdev, "can't start hardware\n"); > + return ret; > + } > + > + ret = hid_hw_open(hdev); > + if (ret) { > + hid_err(hdev, "can't open device\n"); > + goto err_hstop; > + } > + > + mutex_init(&mcp->lock); > + init_completion(&mcp->wait_in_report); > + hid_set_drvdata(hdev, mcp); > + mcp->hdev = hdev; > + > + /* Set I2C bus clock diviser */ > + if (i2c_clk_freq > 400) > + i2c_clk_freq = 400; > + if (i2c_clk_freq < 50) > + i2c_clk_freq = 50; > + mcp->cur_i2c_clk_div = (12000000 / (i2c_clk_freq * 1000)) - 3; > + > + mcp->adapter.owner = THIS_MODULE; > + mcp->adapter.class = I2C_CLASS_HWMON; > + mcp->adapter.algo = &mcp_i2c_algo; > + mcp->adapter.retries = 1; > + mcp->adapter.dev.parent = &hdev->dev; > + snprintf(mcp->adapter.name, sizeof(mcp->adapter.name), > + "mcp2221 at usb bus %03d dev %03d", usd->bus->busnum, > + usd->devnum); AFAICT, this is the only place you use usd. So it would be best to use the same type of name hid-cp2112.c uses: just a reference to hidraw if you need. Then, users can get which USB device is used by looking at the sysfs tree. > + > + ret = i2c_add_adapter(&mcp->adapter); > + if (ret) { > + hid_err(hdev, "can't add usb-i2c adapter: %d\n", ret); > + goto err_i2c; > + } > + i2c_set_adapdata(&mcp->adapter, mcp); > + > + return 0; > + > +err_i2c: > + hid_hw_close(mcp->hdev); > +err_hstop: > + hid_hw_stop(mcp->hdev); > + return ret; > +} > + > +static void mcp2221_remove(struct hid_device *hdev) > +{ > + struct mcp2221 *mcp = hid_get_drvdata(hdev); > + > + i2c_del_adapter(&mcp->adapter); > + hid_hw_close(mcp->hdev); > + hid_hw_stop(mcp->hdev); > +} > + > +static const struct hid_device_id mcp2221_devices[] = { > + { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_MCP2221) }, > + { } > +}; > +MODULE_DEVICE_TABLE(hid, mcp2221_devices); > + > +static struct hid_driver mcp2221_driver = { > + .name = "mcp2221", > + .id_table = mcp2221_devices, > + .probe = mcp2221_probe, > + .remove = mcp2221_remove, > + .raw_event = mcp2221_raw_event, > +}; > + > +/* Register with HID core */ > +module_hid_driver(mcp2221_driver); > + > +/* I2C bus clock frequency can be set only during driver loading */ > +module_param(i2c_clk_freq, uint, 0444); > +MODULE_PARM_DESC(i2c_clk_freq, "I2C bus clock frequency 50-400 kHz"); > + > +MODULE_AUTHOR("Rishi Gupta <gupt21@gmail.com>"); > +MODULE_DESCRIPTION("MCP2221 Microchip HID USB to I2C master bridge"); > +MODULE_LICENSE("GPL v2"); > diff --git a/drivers/hid/hid-quirks.c b/drivers/hid/hid-quirks.c > index 0e7b2d9..ee815eb 100644 > --- a/drivers/hid/hid-quirks.c > +++ b/drivers/hid/hid-quirks.c > @@ -473,6 +473,9 @@ static const struct hid_device_id hid_have_special_driver[] = { > { HID_USB_DEVICE(USB_VENDOR_ID_DRAGONRISE, USB_DEVICE_ID_DRAGONRISE_GAMECUBE1) }, > { HID_USB_DEVICE(USB_VENDOR_ID_DRAGONRISE, USB_DEVICE_ID_DRAGONRISE_GAMECUBE2) }, > #endif > +#if IS_ENABLED(CONFIG_HID_MCP2221) > + { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_MCP2221) }, > +#endif Unless there is a strong argument for that, you should drop this hunk. It should just work even if hid-generic gets bound at boot time. Cheers, Benjamin > #if IS_ENABLED(CONFIG_HID_MICROSOFT) > { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_COMFORT_MOUSE_4500) }, > { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_COMFORT_KEYBOARD) }, > -- > 2.7.4 >
Thanks Benjamin for the review. I have made most of the changes for next patch except module parameter. Please see inline: On Wed, Jan 22, 2020 at 4:58 AM Benjamin Tissoires <benjamin.tissoires@redhat.com> wrote: > > Hi Rishi, > > On Tue, Jan 21, 2020 at 2:44 PM Rishi Gupta <gupt21@gmail.com> wrote: > > > > MCP2221 is a USB HID to I2C/SMbus host bridge device. This > > commit implements i2c and smbus host adapter support. 7-bit > > address and i2c multi-message transaction is also supported. > > > > Signed-off-by: Rishi Gupta <gupt21@gmail.com> > > --- > > Thanks for the driver. Well, this is not a full review, but a few > things jumped to my mind when scheming through this patch. > > Comments inlined > > > > > Changes in v2: > > * added myself in MAINTAINERS for this driver > > * use macro from hid-ids.h for usb vid and pid > > * optimize mcp_i2c_write() - less coding > > * correctly set data length in smbus transaction hid report > > * added static keyword before int mcp_smbus_xfer() > > * replace references to silicon labs with microchip > > > > Only smbus block/proc is not tested due to lack of appropriate > > hardware. Rest all is fully tested. > > > > MAINTAINERS | 7 + > > drivers/hid/Kconfig | 10 + > > drivers/hid/Makefile | 1 + > > drivers/hid/hid-ids.h | 1 + > > drivers/hid/hid-mcp2221.c | 756 ++++++++++++++++++++++++++++++++++++++++++++++ > > drivers/hid/hid-quirks.c | 3 + > > 6 files changed, 778 insertions(+) > > create mode 100644 drivers/hid/hid-mcp2221.c > > > > diff --git a/MAINTAINERS b/MAINTAINERS > > index cf6ccca..bc392c7 100644 > > --- a/MAINTAINERS > > +++ b/MAINTAINERS > > @@ -10121,6 +10121,13 @@ F: drivers/net/can/m_can/m_can.c > > F: drivers/net/can/m_can/m_can.h > > F: drivers/net/can/m_can/m_can_platform.c > > > > +MCP2221A MICROCHIP USB TO I2C BRIDGE DRIVER > > +M: Rishi Gupta <gupt21@gmail.com> > > +L: linux-i2c@vger.kernel.org > > +L: linux-input@vger.kernel.org > > +S: Maintained > > +F: drivers/hid/hid-mcp2221.c > > + > > MCP4018 AND MCP4531 MICROCHIP DIGITAL POTENTIOMETER DRIVERS > > M: Peter Rosin <peda@axentia.se> > > L: linux-iio@vger.kernel.org > > diff --git a/drivers/hid/Kconfig b/drivers/hid/Kconfig > > index 494a39e..08a2522 100644 > > --- a/drivers/hid/Kconfig > > +++ b/drivers/hid/Kconfig > > @@ -1145,6 +1145,16 @@ config HID_ALPS > > Say Y here if you have a Alps touchpads over i2c-hid or usbhid > > and want support for its special functionalities. > > > > +config HID_MCP2221 > > + tristate "Microchip MCP2221 HID USB-to-I2C/SMbus host support" > > + depends on USB_HID && HIDRAW && I2C > > There should not be a need for USB_HID at that point (see below) Removed HIDRAW as not needed. USB_HID is needed for transport layer. MCP2221 uses HID protocol, uses USB for physical data exchange. Raw reports are exchanged. Silicon labs cp2112 is different from mcp2221 (uses interrupt end point). > > > + ---help--- > > + Provides I2C host adapter functionality over USB through MCP2221 > > AFAICT, only SMBus is provided. Can you export full I2C communication? MCP2221 provides I2C and SMBUS both. > > > + from Microchip. I2C bus speed can be set during driver loading. > > This *feels* wrong. Is that something common enough when loading I2C adapters? I will remove this parameter based on your guidance. But consider these use-cases: a) In embedded world each I2C bus is shared by slave operating at same frequency and this is fully controlled right in the circuit (schematic) itself. But one of the strong use case of this driver is "i2c client driver development on host pc". This saved me around 20 days as power supply of ARM board was not stable enough. b) Slave driver/device during board bring-up. It comes handy to use low frequency. c) Prototyping new ideas and demo them quickly without recompile of anything. > > > + > > + To compile this driver as a module, choose M here: the module > > + will be called hid-mcp2221.ko. > > + > > endmenu > > > > endif # HID > > diff --git a/drivers/hid/Makefile b/drivers/hid/Makefile > > index bfefa36..567a241 100644 > > --- a/drivers/hid/Makefile > > +++ b/drivers/hid/Makefile > > @@ -71,6 +71,7 @@ obj-$(CONFIG_HID_MACALLY) += hid-macally.o > > obj-$(CONFIG_HID_MAGICMOUSE) += hid-magicmouse.o > > obj-$(CONFIG_HID_MALTRON) += hid-maltron.o > > obj-$(CONFIG_HID_MAYFLASH) += hid-mf.o > > +obj-$(CONFIG_HID_MCP2221) += hid-mcp2221.o I will put this before hid-mf.o to maintain alphabetical order > > obj-$(CONFIG_HID_MICROSOFT) += hid-microsoft.o > > obj-$(CONFIG_HID_MONTEREY) += hid-monterey.o > > obj-$(CONFIG_HID_MULTITOUCH) += hid-multitouch.o > > diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h > > index 3a400ce..53236ac 100644 > > --- a/drivers/hid/hid-ids.h > > +++ b/drivers/hid/hid-ids.h > > @@ -819,6 +819,7 @@ > > #define USB_DEVICE_ID_PICK16F1454 0x0042 > > #define USB_DEVICE_ID_PICK16F1454_V2 0xf2f7 > > #define USB_DEVICE_ID_LUXAFOR 0xf372 > > +#define USB_DEVICE_ID_MCP2221 0x00dd > > > > #define USB_VENDOR_ID_MICROSOFT 0x045e > > #define USB_DEVICE_ID_SIDEWINDER_GV 0x003b > > diff --git a/drivers/hid/hid-mcp2221.c b/drivers/hid/hid-mcp2221.c > > new file mode 100644 > > index 0000000..5035f1e > > --- /dev/null > > +++ b/drivers/hid/hid-mcp2221.c > > @@ -0,0 +1,756 @@ > > +// SPDX-License-Identifier: GPL-2.0-only > > +/* > > + * MCP2221A - Microchip USB to I2C Host Protocol Bridge I am replacing USB with USB HID to be more clear/elaborative > > + * > > + * Copyright (c) 2019, Rishi Gupta <gupt21@gmail.com> > > + * > > + * Datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/20005565B.pdf > > + */ > > + > > +#include <linux/module.h> > > +#include <linux/err.h> > > +#include <linux/mutex.h> > > +#include <linux/completion.h> > > +#include <linux/delay.h> > > +#include <linux/hid.h> > > +#include <linux/usb.h> > > This is generally a big "NO" from me. We can actually emulate devices > through uhid.ko, and this is a security hole to randomly access USB > commands on a device emulated by uhid. There is a macro or function > that we can use to check if the device is actually using USB, but this > is only useful when the device is not fully HID compatible and needs > to send USB urbs directly. This is not the case here, so we should > remove that line. I will remove "#include <linux/usb.h>" > > > +#include <linux/i2c.h> > > +#include "hid-ids.h" > > + > > +/* Commands codes in a raw output report */ > > +#define MCP2221_I2C_WR_DATA 0x90 > > +#define MCP2221_I2C_WR_NO_STOP 0x94 > > +#define MCP2221_I2C_RD_DATA 0x91 > > +#define MCP2221_I2C_RD_RPT_START 0x93 > > +#define MCP2221_I2C_GET_DATA 0x40 > > +#define MCP2221_I2C_PARAM_OR_STATUS 0x10 > > +#define MCP2221_I2C_SET_SPEED 0x20 > > +#define MCP2221_I2C_CANCEL 0x10 > > hid-cp2112.c, a similar driver, uses enums here. It would make sense > to use enums as well (and for the rest of the defines). Okay > > > + > > +/* Response codes in a raw input report */ > > +#define MCP2221_SUCCESS 0x00 > > +#define MCP2221_I2C_ENG_BUSY 0x01 > > +#define MCP2221_I2C_START_TOUT 0x12 > > +#define MCP2221_I2C_STOP_TOUT 0x62 > > +#define MCP2221_I2C_WRADDRL_TOUT 0x23 > > +#define MCP2221_I2C_WRDATA_TOUT 0x44 > > +#define MCP2221_I2C_WRADDRL_NACK 0x25 > > +#define MCP2221_I2C_MASK_ADDR_NACK 0x40 > > +#define MCP2221_I2C_WRADDRL_SEND 0x21 > > +#define MCP2221_I2C_ADDR_NACK 0x25 > > +#define MCP2221_I2C_READ_COMPL 0x55 > > + > > +/* > > + * There is no way to distinguish responses. Therefore next command > > + * is sent only after response to previous has been received. Mutex > > + * lock is used for this purpose mainly. > > + */ > > +struct mcp2221 { > > + struct hid_device *hdev; > > + struct i2c_adapter adapter; > > + struct mutex lock; > > + struct completion wait_in_report; > > + u8 *rxbuf; > > + u8 txbuf[64]; > > + int rxbuf_idx; > > + int status; > > + u8 cur_i2c_clk_div; > > +}; > > + > > +/* > > + * Default i2c bus clock frequency in kHz. Override through > > + * module param if required. > > + */ > > Again, this feels wrong to me. I need to be convinced. Mentioned use-cases above, if you still suggest I will remove. No problem. > > > +static uint i2c_clk_freq = 400; > > + > > +/* Synchronously send output report to the device */ > > +static int mcp_send_report(struct mcp2221 *mcp, > > + u8 *out_report, size_t len) > > +{ > > + u8 *buf; > > + int ret; > > + > > + buf = kmemdup(out_report, len, GFP_KERNEL); > > + if (!buf) > > + return -ENOMEM; > > + > > + /* mcp2221 uses interrupt endpoint for out reports */ > > + ret = hid_hw_output_report(mcp->hdev, buf, len); > > + kfree(buf); > > + > > + if (ret < 0) > > + return ret; > > + return 0; > > +} > > + > > +/* > > + * Send o/p report to the device and wait for i/p report to be > > + * received from the device. If the device does not respond, > > + * we timeout. > > + */ > > +static int mcp_send_data_req_status(struct mcp2221 *mcp, > > + u8 *out_report, int len) > > +{ > > + int ret; > > + unsigned long t; > > + > > + reinit_completion(&mcp->wait_in_report); > > + > > + ret = mcp_send_report(mcp, out_report, len); > > + if (ret) > > + return ret; > > + > > + t = wait_for_completion_timeout(&mcp->wait_in_report, > > + msecs_to_jiffies(4000)); > > + if (!t) > > + return -ETIMEDOUT; > > + > > + return mcp->status; > > +} > > + > > +/* Check pass/fail for actual communication with i2c slave */ > > +static int mcp_chk_last_cmd_status(struct mcp2221 *mcp) > > +{ > > + int x; > > + > > + mcp->txbuf[0] = MCP2221_I2C_PARAM_OR_STATUS; > > + > > + for (x = 1; x < 8; x++) > > + mcp->txbuf[x] = 0; > > You should probably use memset instead. Okay, I will use memset at all places mentioned. > > > + > > + return mcp_send_data_req_status(mcp, mcp->txbuf, 8); > > +} > > + > > +/* Cancels last command releasing i2c bus just in case occupied */ > > +static int mcp_cancel_last_cmd(struct mcp2221 *mcp) > > +{ > > + int x; > > + > > + mcp->txbuf[0] = MCP2221_I2C_PARAM_OR_STATUS; > > + mcp->txbuf[1] = 0; > > + mcp->txbuf[2] = MCP2221_I2C_CANCEL; > > + > > + for (x = 3; x < 8; x++) > > + mcp->txbuf[x] = 0; > > memset too here > > > + > > + return mcp_send_data_req_status(mcp, mcp->txbuf, 8); > > +} > > + > > +static int mcp_set_i2c_speed(struct mcp2221 *mcp) > > +{ > > + int ret; > > + > > + mcp->txbuf[0] = MCP2221_I2C_PARAM_OR_STATUS; > > + mcp->txbuf[1] = 0; > > + mcp->txbuf[2] = 0; > > + mcp->txbuf[3] = MCP2221_I2C_SET_SPEED; > > + mcp->txbuf[4] = mcp->cur_i2c_clk_div; > > + mcp->txbuf[5] = 0; > > + mcp->txbuf[6] = 0; > > + mcp->txbuf[7] = 0; > > memset and then assign the non null value fields. > > > + > > + ret = mcp_send_data_req_status(mcp, mcp->txbuf, 8); > > + if (ret) { > > + /* Small delay is needed here */ > > + usleep_range(980, 1000); > > + mcp_cancel_last_cmd(mcp); > > + } > > + > > + return 0; > > +} > > + > > +/* > > + * An output report can contain minimum 1 and maximum 60 user data > > + * bytes. If the number of data bytes is more then 60, we send it > > + * in chunks of 60 bytes. Last chunk may contain exactly 60 or less > > + * bytes. Total number of bytes is informed in very first report to > > + * mcp2221, from that point onwards it first collect all the data > > + * from host and then send to i2c slave device. > > + */ > > +static int mcp_i2c_write(struct mcp2221 *mcp, > > + struct i2c_msg *msg, int type, u8 last_status) > > +{ > > + int ret, len, idx, sent; > > + > > + idx = 0; > > + sent = 0; > > + if (msg->len < 60) > > + len = msg->len; > > + else > > + len = 60; > > + > > + do { > > + mcp->txbuf[0] = type; > > + mcp->txbuf[1] = msg->len & 0xff; > > + mcp->txbuf[2] = msg->len >> 8; > > + mcp->txbuf[3] = (u8)(msg->addr << 1); > > + > > + memcpy(&mcp->txbuf[4], &msg->buf[idx], len); > > + > > + ret = mcp_send_data_req_status(mcp, mcp->txbuf, len + 4); > > + if (ret) > > + return ret; > > + > > + usleep_range(980, 1000); > > + > > + ret = mcp_chk_last_cmd_status(mcp); > > + if (ret) > > + return ret; > > + > > + sent = sent + len; > > + if (sent >= msg->len) > > + break; > > + > > + idx = idx + len; > > + if ((msg->len - sent) < 60) > > + len = msg->len - sent; > > + else > > + len = 60; > > + > > + /* > > + * Testing shows delay is needed between successive writes > > + * otherwise next write fails on first-try from i2c core. > > + * This value is obtained through automated stress testing. > > + */ > > + usleep_range(980, 1000); > > That is a lot a usleeps. Are you sure we have to, or can we just rely > on the HID command completion? Testing shows it is needed. Also example driver from microchip also use these sleeps. ~1 milli-second is needed. > > > + } while (len > 0); > > + > > + return ret; > > +} > > + > > +/* > > + * Device reads all data (0 - 65535 bytes) from i2c slave device and > > + * stores it in device itself. This data is read back from device to > > + * host in multiples of 60 bytes using input reports. > > + */ > > +static int mcp_i2c_smbus_read(struct mcp2221 *mcp, > > + struct i2c_msg *msg, int type, u16 smbus_addr, > > + u8 smbus_len, u8 *smbus_buf) > > +{ > > + int ret; > > + u16 total_len; > > + > > + mcp->txbuf[0] = type; > > + if (msg) { > > + mcp->txbuf[1] = msg->len & 0xff; > > + mcp->txbuf[2] = msg->len >> 8; > > + mcp->txbuf[3] = (u8)(msg->addr << 1); > > + total_len = msg->len; > > + mcp->rxbuf = msg->buf; > > + } else { > > + mcp->txbuf[1] = smbus_len; > > + mcp->txbuf[2] = 0; > > + mcp->txbuf[3] = (u8)(smbus_addr << 1); > > + total_len = smbus_len; > > + mcp->rxbuf = smbus_buf; > > + } > > + > > + ret = mcp_send_data_req_status(mcp, mcp->txbuf, 4); > > + if (ret) > > + return ret; > > + > > + mcp->rxbuf_idx = 0; > > + > > + do { > > + mcp->txbuf[0] = MCP2221_I2C_GET_DATA; > > + mcp->txbuf[1] = 0; > > + mcp->txbuf[2] = 0; > > + mcp->txbuf[3] = 0; > > please memset > > > + > > + ret = mcp_send_data_req_status(mcp, mcp->txbuf, 1); > > + if (ret) > > + return ret; > > + > > + ret = mcp_chk_last_cmd_status(mcp); > > + if (ret) > > + return ret; > > + > > + usleep_range(980, 1000); > > + } while (mcp->rxbuf_idx < total_len); > > + > > + return ret; > > +} > > + > > +static int mcp_i2c_xfer(struct i2c_adapter *adapter, > > + struct i2c_msg msgs[], int num) > > +{ > > + int ret; > > + struct mcp2221 *mcp = i2c_get_adapdata(adapter); > > + > > + hid_hw_power(mcp->hdev, PM_HINT_FULLON); > > + > > + mutex_lock(&mcp->lock); > > + > > + /* Setting speed before every transaction is required for mcp2221 */ > > + ret = mcp_set_i2c_speed(mcp); > > + if (ret) > > + goto exit; > > + > > + if (num == 1) { > > + if (msgs->flags & I2C_M_RD) { > > + ret = mcp_i2c_smbus_read(mcp, msgs, MCP2221_I2C_RD_DATA, > > + 0, 0, NULL); > > + } else { > > + ret = mcp_i2c_write(mcp, msgs, MCP2221_I2C_WR_DATA, 1); > > + } > > + if (ret) > > + goto exit; > > + ret = num; > > + } else if (num == 2) { > > + /* Ex transaction; send reg address and read its contents */ > > + if (msgs[0].addr == msgs[1].addr && > > + !(msgs[0].flags & I2C_M_RD) && > > + (msgs[1].flags & I2C_M_RD)) { > > + > > + ret = mcp_i2c_write(mcp, &msgs[0], > > + MCP2221_I2C_WR_NO_STOP, 0); > > + if (ret) > > + goto exit; > > + > > + ret = mcp_i2c_smbus_read(mcp, &msgs[1], > > + MCP2221_I2C_RD_RPT_START, > > + 0, 0, NULL); > > + if (ret) > > + goto exit; > > + ret = num; > > + } else { > > + dev_err(&adapter->dev, > > + "unsupported i2c transaction size: %d\n", num); > > + ret = -EOPNOTSUPP; > > + } > > + } else { > > + dev_err(&adapter->dev, > > + "unsupported i2c transaction size: %d\n", num); > > + ret = -EOPNOTSUPP; > > + } > > + > > +exit: > > + hid_hw_power(mcp->hdev, PM_HINT_NORMAL); > > + mutex_unlock(&mcp->lock); > > + return ret; > > +} > > + > > +static int mcp_smbus_write(struct mcp2221 *mcp, u16 addr, > > + u8 command, u8 *buf, u8 len, int type, > > + u8 last_status) > > +{ > > + int data_len, ret; > > + > > + mcp->txbuf[0] = type; > > + mcp->txbuf[1] = len + 1; /* 1 is due to command byte itself */ > > + mcp->txbuf[2] = 0; > > + mcp->txbuf[3] = (u8)(addr << 1); > > + mcp->txbuf[4] = command; > > + > > + switch (len) { > > + case 0: > > + data_len = 5; > > + break; > > + case 1: > > + mcp->txbuf[5] = buf[0]; > > + data_len = 6; > > + break; > > + case 2: > > + mcp->txbuf[5] = buf[0]; > > + mcp->txbuf[6] = buf[1]; > > + data_len = 7; > > + break; > > + default: > > + memcpy(&mcp->txbuf[5], buf, len); > > + data_len = len + 5; > > + } > > + > > + ret = mcp_send_data_req_status(mcp, mcp->txbuf, data_len); > > + if (ret) > > + return ret; > > + > > + if (last_status) { > > + usleep_range(980, 1000); > > + > > + ret = mcp_chk_last_cmd_status(mcp); > > + if (ret) > > + return ret; > > + } > > + > > + return ret; > > +} > > + > > +static int mcp_smbus_xfer(struct i2c_adapter *adapter, u16 addr, > > + unsigned short flags, char read_write, > > + u8 command, int size, > > + union i2c_smbus_data *data) > > +{ > > + int ret; > > + struct mcp2221 *mcp = i2c_get_adapdata(adapter); > > + > > + hid_hw_power(mcp->hdev, PM_HINT_FULLON); > > + > > + mutex_lock(&mcp->lock); > > + > > + ret = mcp_set_i2c_speed(mcp); > > + if (ret) > > + goto exit; > > + > > + switch (size) { > > + > > + case I2C_SMBUS_QUICK: > > + if (read_write == I2C_SMBUS_READ) > > + ret = mcp_i2c_smbus_read(mcp, NULL, MCP2221_I2C_RD_DATA, > > + addr, 0, &data->byte); > > + else > > + ret = mcp_smbus_write(mcp, addr, command, NULL, > > + 0, MCP2221_I2C_WR_DATA, 1); > > + break; > > + case I2C_SMBUS_BYTE: > > + if (read_write == I2C_SMBUS_READ) > > + ret = mcp_i2c_smbus_read(mcp, NULL, MCP2221_I2C_RD_DATA, > > + addr, 1, &data->byte); > > + else > > + ret = mcp_smbus_write(mcp, addr, command, NULL, > > + 0, MCP2221_I2C_WR_DATA, 1); > > + break; > > + case I2C_SMBUS_BYTE_DATA: > > + if (read_write == I2C_SMBUS_READ) { > > + ret = mcp_smbus_write(mcp, addr, command, NULL, > > + 0, MCP2221_I2C_WR_NO_STOP, 0); > > + if (ret) > > + goto exit; > > + > > + ret = mcp_i2c_smbus_read(mcp, NULL, > > + MCP2221_I2C_RD_RPT_START, > > + addr, 1, &data->byte); > > + } else { > > + ret = mcp_smbus_write(mcp, addr, command, &data->byte, > > + 1, MCP2221_I2C_WR_DATA, 1); > > + } > > + break; > > + case I2C_SMBUS_WORD_DATA: > > + if (read_write == I2C_SMBUS_READ) { > > + ret = mcp_smbus_write(mcp, addr, command, NULL, > > + 0, MCP2221_I2C_WR_NO_STOP, 0); > > + if (ret) > > + goto exit; > > + > > + ret = mcp_i2c_smbus_read(mcp, NULL, > > + MCP2221_I2C_RD_RPT_START, > > + addr, 2, (u8 *)&data->word); > > + } else { > > + ret = mcp_smbus_write(mcp, addr, command, > > + (u8 *)&data->word, 2, > > + MCP2221_I2C_WR_DATA, 1); > > + } > > + break; > > + case I2C_SMBUS_BLOCK_DATA: > > + if (read_write == I2C_SMBUS_READ) { > > + ret = mcp_smbus_write(mcp, addr, command, NULL, > > + 0, MCP2221_I2C_WR_NO_STOP, 1); > > + if (ret) > > + goto exit; > > + > > + mcp->rxbuf_idx = 0; > > + mcp->rxbuf = data->block; > > + mcp->txbuf[0] = MCP2221_I2C_GET_DATA; > > + ret = mcp_send_data_req_status(mcp, mcp->txbuf, 1); > > + if (ret) > > + goto exit; > > + } else { > > + if (!data->block[0]) { > > + ret = -EINVAL; > > + goto exit; > > + } > > + ret = mcp_smbus_write(mcp, addr, command, data->block, > > + data->block[0] + 1, > > + MCP2221_I2C_WR_DATA, 1); > > + } > > + break; > > + case I2C_SMBUS_I2C_BLOCK_DATA: > > + if (read_write == I2C_SMBUS_READ) { > > + ret = mcp_smbus_write(mcp, addr, command, NULL, > > + 0, MCP2221_I2C_WR_NO_STOP, 1); > > + if (ret) > > + goto exit; > > + > > + mcp->rxbuf_idx = 0; > > + mcp->rxbuf = data->block; > > + mcp->txbuf[0] = MCP2221_I2C_GET_DATA; > > + ret = mcp_send_data_req_status(mcp, mcp->txbuf, 1); > > + if (ret) > > + goto exit; > > + } else { > > + if (!data->block[0]) { > > + ret = -EINVAL; > > + goto exit; > > + } > > + ret = mcp_smbus_write(mcp, addr, command, > > + &data->block[1], data->block[0], > > + MCP2221_I2C_WR_DATA, 1); > > + } > > + break; > > + case I2C_SMBUS_PROC_CALL: > > + ret = mcp_smbus_write(mcp, addr, command, > > + (u8 *)&data->word, > > + 2, MCP2221_I2C_WR_NO_STOP, 0); > > + if (ret) > > + goto exit; > > + > > + ret = mcp_i2c_smbus_read(mcp, NULL, > > + MCP2221_I2C_RD_RPT_START, > > + addr, 2, (u8 *)&data->word); > > + break; > > + case I2C_SMBUS_BLOCK_PROC_CALL: > > + ret = mcp_smbus_write(mcp, addr, command, data->block, > > + data->block[0] + 1, > > + MCP2221_I2C_WR_NO_STOP, 0); > > + if (ret) > > + goto exit; > > + > > + ret = mcp_i2c_smbus_read(mcp, NULL, > > + MCP2221_I2C_RD_RPT_START, > > + addr, I2C_SMBUS_BLOCK_MAX, > > + data->block); > > + break; > > + default: > > + dev_err(&mcp->adapter.dev, > > + "unsupported smbus transaction size:%d\n", size); > > + ret = -EOPNOTSUPP; > > + } > > + > > +exit: > > + hid_hw_power(mcp->hdev, PM_HINT_NORMAL); > > + mutex_unlock(&mcp->lock); > > + return ret; > > +} > > + > > +static u32 mcp_i2c_func(struct i2c_adapter *adapter) > > +{ > > + return I2C_FUNC_I2C | > > + I2C_FUNC_SMBUS_READ_BLOCK_DATA | > > + I2C_FUNC_SMBUS_BLOCK_PROC_CALL | > > + (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_PEC); > > +} > > + > > +static const struct i2c_algorithm mcp_i2c_algo = { > > + .master_xfer = mcp_i2c_xfer, > > + .smbus_xfer = mcp_smbus_xfer, > > + .functionality = mcp_i2c_func, > > +}; > > + > > +/* Gives current state of i2c engine inside mcp2221 */ > > +static int mcp_get_i2c_eng_state(struct mcp2221 *mcp, > > + u8 *data, u8 idx) > > +{ > > + int ret; > > + > > + switch (data[idx]) { > > + case MCP2221_I2C_WRADDRL_NACK: > > + case MCP2221_I2C_WRADDRL_SEND: > > + ret = -ENXIO; > > + break; > > + case MCP2221_I2C_START_TOUT: > > + case MCP2221_I2C_STOP_TOUT: > > + case MCP2221_I2C_WRADDRL_TOUT: > > + case MCP2221_I2C_WRDATA_TOUT: > > + ret = -ETIMEDOUT; > > + break; > > + case MCP2221_I2C_ENG_BUSY: > > + ret = -EAGAIN; > > + break; > > + case MCP2221_SUCCESS: > > + ret = 0x00; > > + break; > > + default: > > + ret = -EIO; > > + } > > + > > + return ret; > > +} > > + > > +/* > > + * MCP2221 uses interrupt endpoint for input reports. This function > > + * is called by HID layer when it receives i/p report from mcp2221, > > + * which is actually a response to the previously sent command. > > + * > > + * MCP2221A firmware specific return codes are parsed and 0 or > > + * appropriate negative error code is returned. Delayed response > > + * results in timeout error and stray reponses results in -EIO. > > + */ > > +static int mcp2221_raw_event(struct hid_device *hdev, > > + struct hid_report *report, u8 *data, int size) > > +{ > > + u8 *buf; > > + struct mcp2221 *mcp = hid_get_drvdata(hdev); > > + > > + switch (data[0]) { > > + > > + case MCP2221_I2C_WR_DATA: > > + case MCP2221_I2C_WR_NO_STOP: > > + case MCP2221_I2C_RD_DATA: > > + case MCP2221_I2C_RD_RPT_START: > > + switch (data[1]) { > > + case MCP2221_SUCCESS: > > + mcp->status = 0; > > + break; > > + default: > > + mcp->status = mcp_get_i2c_eng_state(mcp, data, 2); > > + } > > + complete(&mcp->wait_in_report); > > + break; > > + > > + case MCP2221_I2C_PARAM_OR_STATUS: > > + switch (data[1]) { > > + case MCP2221_SUCCESS: > > + if ((mcp->txbuf[3] == MCP2221_I2C_SET_SPEED) && > > + (data[3] != MCP2221_I2C_SET_SPEED)) { > > + mcp->status = -EAGAIN; > > + break; > > + } > > + if (data[20] & MCP2221_I2C_MASK_ADDR_NACK) { > > + mcp->status = -ENXIO; > > + break; > > + } > > + mcp->status = mcp_get_i2c_eng_state(mcp, data, 8); > > + break; > > + default: > > + mcp->status = -EIO; > > + } > > + complete(&mcp->wait_in_report); > > + break; > > + > > + case MCP2221_I2C_GET_DATA: > > + switch (data[1]) { > > + case MCP2221_SUCCESS: > > + if (data[2] == MCP2221_I2C_ADDR_NACK) { > > + mcp->status = -ENXIO; > > + break; > > + } > > + if (!mcp_get_i2c_eng_state(mcp, data, 2) > > + && (data[3] == 0)) { > > + mcp->status = 0; > > + break; > > + } > > + if (data[3] == 127) { > > + mcp->status = -EIO; > > + break; > > + } > > + if (data[2] == MCP2221_I2C_READ_COMPL) { > > + buf = mcp->rxbuf; > > + memcpy(&buf[mcp->rxbuf_idx], &data[4], data[3]); > > + mcp->rxbuf_idx = mcp->rxbuf_idx + data[3]; > > + mcp->status = 0; > > + break; > > + } > > + mcp->status = -EIO; > > + break; > > + default: > > + mcp->status = -EIO; > > + } > > + complete(&mcp->wait_in_report); > > + break; > > + > > + default: > > + mcp->status = -EIO; > > + complete(&mcp->wait_in_report); > > + } > > + > > + return 1; > > +} > > + > > +static int mcp2221_probe(struct hid_device *hdev, > > + const struct hid_device_id *id) > > +{ > > + int ret; > > + struct mcp2221 *mcp; > > + struct usb_device *usd = to_usb_device(hdev->dev.parent->parent); > > You should ensure you are actually talking to a USB device. Otherwise, > you are happily jumping to random addresses. > But again, please drop any USB references. Okay > > > + > > + mcp = devm_kzalloc(&hdev->dev, sizeof(*mcp), GFP_KERNEL); > > + if (!mcp) > > + return -ENOMEM; > > + > > + ret = hid_parse(hdev); > > + if (ret) { > > + hid_err(hdev, "can't parse reports\n"); > > + return ret; > > + } > > + > > + ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT); > > + if (ret) { > > + hid_err(hdev, "can't start hardware\n"); > > + return ret; > > + } > > + > > + ret = hid_hw_open(hdev); > > + if (ret) { > > + hid_err(hdev, "can't open device\n"); > > + goto err_hstop; > > + } > > + > > + mutex_init(&mcp->lock); > > + init_completion(&mcp->wait_in_report); > > + hid_set_drvdata(hdev, mcp); > > + mcp->hdev = hdev; > > + > > + /* Set I2C bus clock diviser */ > > + if (i2c_clk_freq > 400) > > + i2c_clk_freq = 400; > > + if (i2c_clk_freq < 50) > > + i2c_clk_freq = 50; > > + mcp->cur_i2c_clk_div = (12000000 / (i2c_clk_freq * 1000)) - 3; > > + > > + mcp->adapter.owner = THIS_MODULE; > > + mcp->adapter.class = I2C_CLASS_HWMON; > > + mcp->adapter.algo = &mcp_i2c_algo; > > + mcp->adapter.retries = 1; > > + mcp->adapter.dev.parent = &hdev->dev; > > + snprintf(mcp->adapter.name, sizeof(mcp->adapter.name), > > + "mcp2221 at usb bus %03d dev %03d", usd->bus->busnum, > > + usd->devnum); > > AFAICT, this is the only place you use usd. So it would be best to use > the same type of name hid-cp2112.c uses: just a reference to hidraw if > you need. Then, users can get which USB device is used by looking at > the sysfs tree. Okay > > > + > > + ret = i2c_add_adapter(&mcp->adapter); > > + if (ret) { > > + hid_err(hdev, "can't add usb-i2c adapter: %d\n", ret); > > + goto err_i2c; > > + } > > + i2c_set_adapdata(&mcp->adapter, mcp); > > + > > + return 0; > > + > > +err_i2c: > > + hid_hw_close(mcp->hdev); > > +err_hstop: > > + hid_hw_stop(mcp->hdev); > > + return ret; > > +} > > + > > +static void mcp2221_remove(struct hid_device *hdev) > > +{ > > + struct mcp2221 *mcp = hid_get_drvdata(hdev); > > + > > + i2c_del_adapter(&mcp->adapter); > > + hid_hw_close(mcp->hdev); > > + hid_hw_stop(mcp->hdev); > > +} > > + > > +static const struct hid_device_id mcp2221_devices[] = { > > + { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_MCP2221) }, > > + { } > > +}; > > +MODULE_DEVICE_TABLE(hid, mcp2221_devices); > > + > > +static struct hid_driver mcp2221_driver = { > > + .name = "mcp2221", > > + .id_table = mcp2221_devices, > > + .probe = mcp2221_probe, > > + .remove = mcp2221_remove, > > + .raw_event = mcp2221_raw_event, > > +}; > > + > > +/* Register with HID core */ > > +module_hid_driver(mcp2221_driver); > > + > > +/* I2C bus clock frequency can be set only during driver loading */ > > +module_param(i2c_clk_freq, uint, 0444); > > +MODULE_PARM_DESC(i2c_clk_freq, "I2C bus clock frequency 50-400 kHz"); > > + > > +MODULE_AUTHOR("Rishi Gupta <gupt21@gmail.com>"); > > +MODULE_DESCRIPTION("MCP2221 Microchip HID USB to I2C master bridge"); > > +MODULE_LICENSE("GPL v2"); > > diff --git a/drivers/hid/hid-quirks.c b/drivers/hid/hid-quirks.c > > index 0e7b2d9..ee815eb 100644 > > --- a/drivers/hid/hid-quirks.c > > +++ b/drivers/hid/hid-quirks.c > > @@ -473,6 +473,9 @@ static const struct hid_device_id hid_have_special_driver[] = { > > { HID_USB_DEVICE(USB_VENDOR_ID_DRAGONRISE, USB_DEVICE_ID_DRAGONRISE_GAMECUBE1) }, > > { HID_USB_DEVICE(USB_VENDOR_ID_DRAGONRISE, USB_DEVICE_ID_DRAGONRISE_GAMECUBE2) }, > > #endif > > +#if IS_ENABLED(CONFIG_HID_MCP2221) > > + { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_MCP2221) }, > > +#endif > > Unless there is a strong argument for that, you should drop this hunk. > It should just work even if hid-generic gets bound at boot time. Okay > > Cheers, > Benjamin > > > #if IS_ENABLED(CONFIG_HID_MICROSOFT) > > { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_COMFORT_MOUSE_4500) }, > > { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_COMFORT_KEYBOARD) }, > > -- > > 2.7.4 > > >
On Tue, Jan 21, 2020 at 10:14:20AM +0530, Rishi Gupta wrote: > MCP2221 is a USB HID to I2C/SMbus host bridge device. This > commit implements i2c and smbus host adapter support. 7-bit > address and i2c multi-message transaction is also supported. > > Signed-off-by: Rishi Gupta <gupt21@gmail.com> My main concern is there are quite some limitations in mcp_i2c_xfer(). Looking at them, I think we should just drop it. This seems to be an SMBus controller, not I2C. Or?
It is both I2C and SMBus. Title of the product itself is "USB 2.0 to I^2C/UART Protocol Converter with GPIO" https://www.microchip.com/wwwproducts/en/MCP2221A If I am mistaken in something, please help me with specific thing so that I can dive more from that perspective. On Wed, Jan 22, 2020 at 6:43 PM Wolfram Sang <wsa@the-dreams.de> wrote: > > On Tue, Jan 21, 2020 at 10:14:20AM +0530, Rishi Gupta wrote: > > MCP2221 is a USB HID to I2C/SMbus host bridge device. This > > commit implements i2c and smbus host adapter support. 7-bit > > address and i2c multi-message transaction is also supported. > > > > Signed-off-by: Rishi Gupta <gupt21@gmail.com> > > My main concern is there are quite some limitations in mcp_i2c_xfer(). > Looking at them, I think we should just drop it. This seems to be an > SMBus controller, not I2C. Or? >
diff --git a/MAINTAINERS b/MAINTAINERS index cf6ccca..bc392c7 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -10121,6 +10121,13 @@ F: drivers/net/can/m_can/m_can.c F: drivers/net/can/m_can/m_can.h F: drivers/net/can/m_can/m_can_platform.c +MCP2221A MICROCHIP USB TO I2C BRIDGE DRIVER +M: Rishi Gupta <gupt21@gmail.com> +L: linux-i2c@vger.kernel.org +L: linux-input@vger.kernel.org +S: Maintained +F: drivers/hid/hid-mcp2221.c + MCP4018 AND MCP4531 MICROCHIP DIGITAL POTENTIOMETER DRIVERS M: Peter Rosin <peda@axentia.se> L: linux-iio@vger.kernel.org diff --git a/drivers/hid/Kconfig b/drivers/hid/Kconfig index 494a39e..08a2522 100644 --- a/drivers/hid/Kconfig +++ b/drivers/hid/Kconfig @@ -1145,6 +1145,16 @@ config HID_ALPS Say Y here if you have a Alps touchpads over i2c-hid or usbhid and want support for its special functionalities. +config HID_MCP2221 + tristate "Microchip MCP2221 HID USB-to-I2C/SMbus host support" + depends on USB_HID && HIDRAW && I2C + ---help--- + Provides I2C host adapter functionality over USB through MCP2221 + from Microchip. I2C bus speed can be set during driver loading. + + To compile this driver as a module, choose M here: the module + will be called hid-mcp2221.ko. + endmenu endif # HID diff --git a/drivers/hid/Makefile b/drivers/hid/Makefile index bfefa36..567a241 100644 --- a/drivers/hid/Makefile +++ b/drivers/hid/Makefile @@ -71,6 +71,7 @@ obj-$(CONFIG_HID_MACALLY) += hid-macally.o obj-$(CONFIG_HID_MAGICMOUSE) += hid-magicmouse.o obj-$(CONFIG_HID_MALTRON) += hid-maltron.o obj-$(CONFIG_HID_MAYFLASH) += hid-mf.o +obj-$(CONFIG_HID_MCP2221) += hid-mcp2221.o obj-$(CONFIG_HID_MICROSOFT) += hid-microsoft.o obj-$(CONFIG_HID_MONTEREY) += hid-monterey.o obj-$(CONFIG_HID_MULTITOUCH) += hid-multitouch.o diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h index 3a400ce..53236ac 100644 --- a/drivers/hid/hid-ids.h +++ b/drivers/hid/hid-ids.h @@ -819,6 +819,7 @@ #define USB_DEVICE_ID_PICK16F1454 0x0042 #define USB_DEVICE_ID_PICK16F1454_V2 0xf2f7 #define USB_DEVICE_ID_LUXAFOR 0xf372 +#define USB_DEVICE_ID_MCP2221 0x00dd #define USB_VENDOR_ID_MICROSOFT 0x045e #define USB_DEVICE_ID_SIDEWINDER_GV 0x003b diff --git a/drivers/hid/hid-mcp2221.c b/drivers/hid/hid-mcp2221.c new file mode 100644 index 0000000..5035f1e --- /dev/null +++ b/drivers/hid/hid-mcp2221.c @@ -0,0 +1,756 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * MCP2221A - Microchip USB to I2C Host Protocol Bridge + * + * Copyright (c) 2019, Rishi Gupta <gupt21@gmail.com> + * + * Datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/20005565B.pdf + */ + +#include <linux/module.h> +#include <linux/err.h> +#include <linux/mutex.h> +#include <linux/completion.h> +#include <linux/delay.h> +#include <linux/hid.h> +#include <linux/usb.h> +#include <linux/i2c.h> +#include "hid-ids.h" + +/* Commands codes in a raw output report */ +#define MCP2221_I2C_WR_DATA 0x90 +#define MCP2221_I2C_WR_NO_STOP 0x94 +#define MCP2221_I2C_RD_DATA 0x91 +#define MCP2221_I2C_RD_RPT_START 0x93 +#define MCP2221_I2C_GET_DATA 0x40 +#define MCP2221_I2C_PARAM_OR_STATUS 0x10 +#define MCP2221_I2C_SET_SPEED 0x20 +#define MCP2221_I2C_CANCEL 0x10 + +/* Response codes in a raw input report */ +#define MCP2221_SUCCESS 0x00 +#define MCP2221_I2C_ENG_BUSY 0x01 +#define MCP2221_I2C_START_TOUT 0x12 +#define MCP2221_I2C_STOP_TOUT 0x62 +#define MCP2221_I2C_WRADDRL_TOUT 0x23 +#define MCP2221_I2C_WRDATA_TOUT 0x44 +#define MCP2221_I2C_WRADDRL_NACK 0x25 +#define MCP2221_I2C_MASK_ADDR_NACK 0x40 +#define MCP2221_I2C_WRADDRL_SEND 0x21 +#define MCP2221_I2C_ADDR_NACK 0x25 +#define MCP2221_I2C_READ_COMPL 0x55 + +/* + * There is no way to distinguish responses. Therefore next command + * is sent only after response to previous has been received. Mutex + * lock is used for this purpose mainly. + */ +struct mcp2221 { + struct hid_device *hdev; + struct i2c_adapter adapter; + struct mutex lock; + struct completion wait_in_report; + u8 *rxbuf; + u8 txbuf[64]; + int rxbuf_idx; + int status; + u8 cur_i2c_clk_div; +}; + +/* + * Default i2c bus clock frequency in kHz. Override through + * module param if required. + */ +static uint i2c_clk_freq = 400; + +/* Synchronously send output report to the device */ +static int mcp_send_report(struct mcp2221 *mcp, + u8 *out_report, size_t len) +{ + u8 *buf; + int ret; + + buf = kmemdup(out_report, len, GFP_KERNEL); + if (!buf) + return -ENOMEM; + + /* mcp2221 uses interrupt endpoint for out reports */ + ret = hid_hw_output_report(mcp->hdev, buf, len); + kfree(buf); + + if (ret < 0) + return ret; + return 0; +} + +/* + * Send o/p report to the device and wait for i/p report to be + * received from the device. If the device does not respond, + * we timeout. + */ +static int mcp_send_data_req_status(struct mcp2221 *mcp, + u8 *out_report, int len) +{ + int ret; + unsigned long t; + + reinit_completion(&mcp->wait_in_report); + + ret = mcp_send_report(mcp, out_report, len); + if (ret) + return ret; + + t = wait_for_completion_timeout(&mcp->wait_in_report, + msecs_to_jiffies(4000)); + if (!t) + return -ETIMEDOUT; + + return mcp->status; +} + +/* Check pass/fail for actual communication with i2c slave */ +static int mcp_chk_last_cmd_status(struct mcp2221 *mcp) +{ + int x; + + mcp->txbuf[0] = MCP2221_I2C_PARAM_OR_STATUS; + + for (x = 1; x < 8; x++) + mcp->txbuf[x] = 0; + + return mcp_send_data_req_status(mcp, mcp->txbuf, 8); +} + +/* Cancels last command releasing i2c bus just in case occupied */ +static int mcp_cancel_last_cmd(struct mcp2221 *mcp) +{ + int x; + + mcp->txbuf[0] = MCP2221_I2C_PARAM_OR_STATUS; + mcp->txbuf[1] = 0; + mcp->txbuf[2] = MCP2221_I2C_CANCEL; + + for (x = 3; x < 8; x++) + mcp->txbuf[x] = 0; + + return mcp_send_data_req_status(mcp, mcp->txbuf, 8); +} + +static int mcp_set_i2c_speed(struct mcp2221 *mcp) +{ + int ret; + + mcp->txbuf[0] = MCP2221_I2C_PARAM_OR_STATUS; + mcp->txbuf[1] = 0; + mcp->txbuf[2] = 0; + mcp->txbuf[3] = MCP2221_I2C_SET_SPEED; + mcp->txbuf[4] = mcp->cur_i2c_clk_div; + mcp->txbuf[5] = 0; + mcp->txbuf[6] = 0; + mcp->txbuf[7] = 0; + + ret = mcp_send_data_req_status(mcp, mcp->txbuf, 8); + if (ret) { + /* Small delay is needed here */ + usleep_range(980, 1000); + mcp_cancel_last_cmd(mcp); + } + + return 0; +} + +/* + * An output report can contain minimum 1 and maximum 60 user data + * bytes. If the number of data bytes is more then 60, we send it + * in chunks of 60 bytes. Last chunk may contain exactly 60 or less + * bytes. Total number of bytes is informed in very first report to + * mcp2221, from that point onwards it first collect all the data + * from host and then send to i2c slave device. + */ +static int mcp_i2c_write(struct mcp2221 *mcp, + struct i2c_msg *msg, int type, u8 last_status) +{ + int ret, len, idx, sent; + + idx = 0; + sent = 0; + if (msg->len < 60) + len = msg->len; + else + len = 60; + + do { + mcp->txbuf[0] = type; + mcp->txbuf[1] = msg->len & 0xff; + mcp->txbuf[2] = msg->len >> 8; + mcp->txbuf[3] = (u8)(msg->addr << 1); + + memcpy(&mcp->txbuf[4], &msg->buf[idx], len); + + ret = mcp_send_data_req_status(mcp, mcp->txbuf, len + 4); + if (ret) + return ret; + + usleep_range(980, 1000); + + ret = mcp_chk_last_cmd_status(mcp); + if (ret) + return ret; + + sent = sent + len; + if (sent >= msg->len) + break; + + idx = idx + len; + if ((msg->len - sent) < 60) + len = msg->len - sent; + else + len = 60; + + /* + * Testing shows delay is needed between successive writes + * otherwise next write fails on first-try from i2c core. + * This value is obtained through automated stress testing. + */ + usleep_range(980, 1000); + } while (len > 0); + + return ret; +} + +/* + * Device reads all data (0 - 65535 bytes) from i2c slave device and + * stores it in device itself. This data is read back from device to + * host in multiples of 60 bytes using input reports. + */ +static int mcp_i2c_smbus_read(struct mcp2221 *mcp, + struct i2c_msg *msg, int type, u16 smbus_addr, + u8 smbus_len, u8 *smbus_buf) +{ + int ret; + u16 total_len; + + mcp->txbuf[0] = type; + if (msg) { + mcp->txbuf[1] = msg->len & 0xff; + mcp->txbuf[2] = msg->len >> 8; + mcp->txbuf[3] = (u8)(msg->addr << 1); + total_len = msg->len; + mcp->rxbuf = msg->buf; + } else { + mcp->txbuf[1] = smbus_len; + mcp->txbuf[2] = 0; + mcp->txbuf[3] = (u8)(smbus_addr << 1); + total_len = smbus_len; + mcp->rxbuf = smbus_buf; + } + + ret = mcp_send_data_req_status(mcp, mcp->txbuf, 4); + if (ret) + return ret; + + mcp->rxbuf_idx = 0; + + do { + mcp->txbuf[0] = MCP2221_I2C_GET_DATA; + mcp->txbuf[1] = 0; + mcp->txbuf[2] = 0; + mcp->txbuf[3] = 0; + + ret = mcp_send_data_req_status(mcp, mcp->txbuf, 1); + if (ret) + return ret; + + ret = mcp_chk_last_cmd_status(mcp); + if (ret) + return ret; + + usleep_range(980, 1000); + } while (mcp->rxbuf_idx < total_len); + + return ret; +} + +static int mcp_i2c_xfer(struct i2c_adapter *adapter, + struct i2c_msg msgs[], int num) +{ + int ret; + struct mcp2221 *mcp = i2c_get_adapdata(adapter); + + hid_hw_power(mcp->hdev, PM_HINT_FULLON); + + mutex_lock(&mcp->lock); + + /* Setting speed before every transaction is required for mcp2221 */ + ret = mcp_set_i2c_speed(mcp); + if (ret) + goto exit; + + if (num == 1) { + if (msgs->flags & I2C_M_RD) { + ret = mcp_i2c_smbus_read(mcp, msgs, MCP2221_I2C_RD_DATA, + 0, 0, NULL); + } else { + ret = mcp_i2c_write(mcp, msgs, MCP2221_I2C_WR_DATA, 1); + } + if (ret) + goto exit; + ret = num; + } else if (num == 2) { + /* Ex transaction; send reg address and read its contents */ + if (msgs[0].addr == msgs[1].addr && + !(msgs[0].flags & I2C_M_RD) && + (msgs[1].flags & I2C_M_RD)) { + + ret = mcp_i2c_write(mcp, &msgs[0], + MCP2221_I2C_WR_NO_STOP, 0); + if (ret) + goto exit; + + ret = mcp_i2c_smbus_read(mcp, &msgs[1], + MCP2221_I2C_RD_RPT_START, + 0, 0, NULL); + if (ret) + goto exit; + ret = num; + } else { + dev_err(&adapter->dev, + "unsupported i2c transaction size: %d\n", num); + ret = -EOPNOTSUPP; + } + } else { + dev_err(&adapter->dev, + "unsupported i2c transaction size: %d\n", num); + ret = -EOPNOTSUPP; + } + +exit: + hid_hw_power(mcp->hdev, PM_HINT_NORMAL); + mutex_unlock(&mcp->lock); + return ret; +} + +static int mcp_smbus_write(struct mcp2221 *mcp, u16 addr, + u8 command, u8 *buf, u8 len, int type, + u8 last_status) +{ + int data_len, ret; + + mcp->txbuf[0] = type; + mcp->txbuf[1] = len + 1; /* 1 is due to command byte itself */ + mcp->txbuf[2] = 0; + mcp->txbuf[3] = (u8)(addr << 1); + mcp->txbuf[4] = command; + + switch (len) { + case 0: + data_len = 5; + break; + case 1: + mcp->txbuf[5] = buf[0]; + data_len = 6; + break; + case 2: + mcp->txbuf[5] = buf[0]; + mcp->txbuf[6] = buf[1]; + data_len = 7; + break; + default: + memcpy(&mcp->txbuf[5], buf, len); + data_len = len + 5; + } + + ret = mcp_send_data_req_status(mcp, mcp->txbuf, data_len); + if (ret) + return ret; + + if (last_status) { + usleep_range(980, 1000); + + ret = mcp_chk_last_cmd_status(mcp); + if (ret) + return ret; + } + + return ret; +} + +static int mcp_smbus_xfer(struct i2c_adapter *adapter, u16 addr, + unsigned short flags, char read_write, + u8 command, int size, + union i2c_smbus_data *data) +{ + int ret; + struct mcp2221 *mcp = i2c_get_adapdata(adapter); + + hid_hw_power(mcp->hdev, PM_HINT_FULLON); + + mutex_lock(&mcp->lock); + + ret = mcp_set_i2c_speed(mcp); + if (ret) + goto exit; + + switch (size) { + + case I2C_SMBUS_QUICK: + if (read_write == I2C_SMBUS_READ) + ret = mcp_i2c_smbus_read(mcp, NULL, MCP2221_I2C_RD_DATA, + addr, 0, &data->byte); + else + ret = mcp_smbus_write(mcp, addr, command, NULL, + 0, MCP2221_I2C_WR_DATA, 1); + break; + case I2C_SMBUS_BYTE: + if (read_write == I2C_SMBUS_READ) + ret = mcp_i2c_smbus_read(mcp, NULL, MCP2221_I2C_RD_DATA, + addr, 1, &data->byte); + else + ret = mcp_smbus_write(mcp, addr, command, NULL, + 0, MCP2221_I2C_WR_DATA, 1); + break; + case I2C_SMBUS_BYTE_DATA: + if (read_write == I2C_SMBUS_READ) { + ret = mcp_smbus_write(mcp, addr, command, NULL, + 0, MCP2221_I2C_WR_NO_STOP, 0); + if (ret) + goto exit; + + ret = mcp_i2c_smbus_read(mcp, NULL, + MCP2221_I2C_RD_RPT_START, + addr, 1, &data->byte); + } else { + ret = mcp_smbus_write(mcp, addr, command, &data->byte, + 1, MCP2221_I2C_WR_DATA, 1); + } + break; + case I2C_SMBUS_WORD_DATA: + if (read_write == I2C_SMBUS_READ) { + ret = mcp_smbus_write(mcp, addr, command, NULL, + 0, MCP2221_I2C_WR_NO_STOP, 0); + if (ret) + goto exit; + + ret = mcp_i2c_smbus_read(mcp, NULL, + MCP2221_I2C_RD_RPT_START, + addr, 2, (u8 *)&data->word); + } else { + ret = mcp_smbus_write(mcp, addr, command, + (u8 *)&data->word, 2, + MCP2221_I2C_WR_DATA, 1); + } + break; + case I2C_SMBUS_BLOCK_DATA: + if (read_write == I2C_SMBUS_READ) { + ret = mcp_smbus_write(mcp, addr, command, NULL, + 0, MCP2221_I2C_WR_NO_STOP, 1); + if (ret) + goto exit; + + mcp->rxbuf_idx = 0; + mcp->rxbuf = data->block; + mcp->txbuf[0] = MCP2221_I2C_GET_DATA; + ret = mcp_send_data_req_status(mcp, mcp->txbuf, 1); + if (ret) + goto exit; + } else { + if (!data->block[0]) { + ret = -EINVAL; + goto exit; + } + ret = mcp_smbus_write(mcp, addr, command, data->block, + data->block[0] + 1, + MCP2221_I2C_WR_DATA, 1); + } + break; + case I2C_SMBUS_I2C_BLOCK_DATA: + if (read_write == I2C_SMBUS_READ) { + ret = mcp_smbus_write(mcp, addr, command, NULL, + 0, MCP2221_I2C_WR_NO_STOP, 1); + if (ret) + goto exit; + + mcp->rxbuf_idx = 0; + mcp->rxbuf = data->block; + mcp->txbuf[0] = MCP2221_I2C_GET_DATA; + ret = mcp_send_data_req_status(mcp, mcp->txbuf, 1); + if (ret) + goto exit; + } else { + if (!data->block[0]) { + ret = -EINVAL; + goto exit; + } + ret = mcp_smbus_write(mcp, addr, command, + &data->block[1], data->block[0], + MCP2221_I2C_WR_DATA, 1); + } + break; + case I2C_SMBUS_PROC_CALL: + ret = mcp_smbus_write(mcp, addr, command, + (u8 *)&data->word, + 2, MCP2221_I2C_WR_NO_STOP, 0); + if (ret) + goto exit; + + ret = mcp_i2c_smbus_read(mcp, NULL, + MCP2221_I2C_RD_RPT_START, + addr, 2, (u8 *)&data->word); + break; + case I2C_SMBUS_BLOCK_PROC_CALL: + ret = mcp_smbus_write(mcp, addr, command, data->block, + data->block[0] + 1, + MCP2221_I2C_WR_NO_STOP, 0); + if (ret) + goto exit; + + ret = mcp_i2c_smbus_read(mcp, NULL, + MCP2221_I2C_RD_RPT_START, + addr, I2C_SMBUS_BLOCK_MAX, + data->block); + break; + default: + dev_err(&mcp->adapter.dev, + "unsupported smbus transaction size:%d\n", size); + ret = -EOPNOTSUPP; + } + +exit: + hid_hw_power(mcp->hdev, PM_HINT_NORMAL); + mutex_unlock(&mcp->lock); + return ret; +} + +static u32 mcp_i2c_func(struct i2c_adapter *adapter) +{ + return I2C_FUNC_I2C | + I2C_FUNC_SMBUS_READ_BLOCK_DATA | + I2C_FUNC_SMBUS_BLOCK_PROC_CALL | + (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_PEC); +} + +static const struct i2c_algorithm mcp_i2c_algo = { + .master_xfer = mcp_i2c_xfer, + .smbus_xfer = mcp_smbus_xfer, + .functionality = mcp_i2c_func, +}; + +/* Gives current state of i2c engine inside mcp2221 */ +static int mcp_get_i2c_eng_state(struct mcp2221 *mcp, + u8 *data, u8 idx) +{ + int ret; + + switch (data[idx]) { + case MCP2221_I2C_WRADDRL_NACK: + case MCP2221_I2C_WRADDRL_SEND: + ret = -ENXIO; + break; + case MCP2221_I2C_START_TOUT: + case MCP2221_I2C_STOP_TOUT: + case MCP2221_I2C_WRADDRL_TOUT: + case MCP2221_I2C_WRDATA_TOUT: + ret = -ETIMEDOUT; + break; + case MCP2221_I2C_ENG_BUSY: + ret = -EAGAIN; + break; + case MCP2221_SUCCESS: + ret = 0x00; + break; + default: + ret = -EIO; + } + + return ret; +} + +/* + * MCP2221 uses interrupt endpoint for input reports. This function + * is called by HID layer when it receives i/p report from mcp2221, + * which is actually a response to the previously sent command. + * + * MCP2221A firmware specific return codes are parsed and 0 or + * appropriate negative error code is returned. Delayed response + * results in timeout error and stray reponses results in -EIO. + */ +static int mcp2221_raw_event(struct hid_device *hdev, + struct hid_report *report, u8 *data, int size) +{ + u8 *buf; + struct mcp2221 *mcp = hid_get_drvdata(hdev); + + switch (data[0]) { + + case MCP2221_I2C_WR_DATA: + case MCP2221_I2C_WR_NO_STOP: + case MCP2221_I2C_RD_DATA: + case MCP2221_I2C_RD_RPT_START: + switch (data[1]) { + case MCP2221_SUCCESS: + mcp->status = 0; + break; + default: + mcp->status = mcp_get_i2c_eng_state(mcp, data, 2); + } + complete(&mcp->wait_in_report); + break; + + case MCP2221_I2C_PARAM_OR_STATUS: + switch (data[1]) { + case MCP2221_SUCCESS: + if ((mcp->txbuf[3] == MCP2221_I2C_SET_SPEED) && + (data[3] != MCP2221_I2C_SET_SPEED)) { + mcp->status = -EAGAIN; + break; + } + if (data[20] & MCP2221_I2C_MASK_ADDR_NACK) { + mcp->status = -ENXIO; + break; + } + mcp->status = mcp_get_i2c_eng_state(mcp, data, 8); + break; + default: + mcp->status = -EIO; + } + complete(&mcp->wait_in_report); + break; + + case MCP2221_I2C_GET_DATA: + switch (data[1]) { + case MCP2221_SUCCESS: + if (data[2] == MCP2221_I2C_ADDR_NACK) { + mcp->status = -ENXIO; + break; + } + if (!mcp_get_i2c_eng_state(mcp, data, 2) + && (data[3] == 0)) { + mcp->status = 0; + break; + } + if (data[3] == 127) { + mcp->status = -EIO; + break; + } + if (data[2] == MCP2221_I2C_READ_COMPL) { + buf = mcp->rxbuf; + memcpy(&buf[mcp->rxbuf_idx], &data[4], data[3]); + mcp->rxbuf_idx = mcp->rxbuf_idx + data[3]; + mcp->status = 0; + break; + } + mcp->status = -EIO; + break; + default: + mcp->status = -EIO; + } + complete(&mcp->wait_in_report); + break; + + default: + mcp->status = -EIO; + complete(&mcp->wait_in_report); + } + + return 1; +} + +static int mcp2221_probe(struct hid_device *hdev, + const struct hid_device_id *id) +{ + int ret; + struct mcp2221 *mcp; + struct usb_device *usd = to_usb_device(hdev->dev.parent->parent); + + mcp = devm_kzalloc(&hdev->dev, sizeof(*mcp), GFP_KERNEL); + if (!mcp) + return -ENOMEM; + + ret = hid_parse(hdev); + if (ret) { + hid_err(hdev, "can't parse reports\n"); + return ret; + } + + ret = hid_hw_start(hdev, HID_CONNECT_DEFAULT); + if (ret) { + hid_err(hdev, "can't start hardware\n"); + return ret; + } + + ret = hid_hw_open(hdev); + if (ret) { + hid_err(hdev, "can't open device\n"); + goto err_hstop; + } + + mutex_init(&mcp->lock); + init_completion(&mcp->wait_in_report); + hid_set_drvdata(hdev, mcp); + mcp->hdev = hdev; + + /* Set I2C bus clock diviser */ + if (i2c_clk_freq > 400) + i2c_clk_freq = 400; + if (i2c_clk_freq < 50) + i2c_clk_freq = 50; + mcp->cur_i2c_clk_div = (12000000 / (i2c_clk_freq * 1000)) - 3; + + mcp->adapter.owner = THIS_MODULE; + mcp->adapter.class = I2C_CLASS_HWMON; + mcp->adapter.algo = &mcp_i2c_algo; + mcp->adapter.retries = 1; + mcp->adapter.dev.parent = &hdev->dev; + snprintf(mcp->adapter.name, sizeof(mcp->adapter.name), + "mcp2221 at usb bus %03d dev %03d", usd->bus->busnum, + usd->devnum); + + ret = i2c_add_adapter(&mcp->adapter); + if (ret) { + hid_err(hdev, "can't add usb-i2c adapter: %d\n", ret); + goto err_i2c; + } + i2c_set_adapdata(&mcp->adapter, mcp); + + return 0; + +err_i2c: + hid_hw_close(mcp->hdev); +err_hstop: + hid_hw_stop(mcp->hdev); + return ret; +} + +static void mcp2221_remove(struct hid_device *hdev) +{ + struct mcp2221 *mcp = hid_get_drvdata(hdev); + + i2c_del_adapter(&mcp->adapter); + hid_hw_close(mcp->hdev); + hid_hw_stop(mcp->hdev); +} + +static const struct hid_device_id mcp2221_devices[] = { + { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_MCP2221) }, + { } +}; +MODULE_DEVICE_TABLE(hid, mcp2221_devices); + +static struct hid_driver mcp2221_driver = { + .name = "mcp2221", + .id_table = mcp2221_devices, + .probe = mcp2221_probe, + .remove = mcp2221_remove, + .raw_event = mcp2221_raw_event, +}; + +/* Register with HID core */ +module_hid_driver(mcp2221_driver); + +/* I2C bus clock frequency can be set only during driver loading */ +module_param(i2c_clk_freq, uint, 0444); +MODULE_PARM_DESC(i2c_clk_freq, "I2C bus clock frequency 50-400 kHz"); + +MODULE_AUTHOR("Rishi Gupta <gupt21@gmail.com>"); +MODULE_DESCRIPTION("MCP2221 Microchip HID USB to I2C master bridge"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/hid/hid-quirks.c b/drivers/hid/hid-quirks.c index 0e7b2d9..ee815eb 100644 --- a/drivers/hid/hid-quirks.c +++ b/drivers/hid/hid-quirks.c @@ -473,6 +473,9 @@ static const struct hid_device_id hid_have_special_driver[] = { { HID_USB_DEVICE(USB_VENDOR_ID_DRAGONRISE, USB_DEVICE_ID_DRAGONRISE_GAMECUBE1) }, { HID_USB_DEVICE(USB_VENDOR_ID_DRAGONRISE, USB_DEVICE_ID_DRAGONRISE_GAMECUBE2) }, #endif +#if IS_ENABLED(CONFIG_HID_MCP2221) + { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_MCP2221) }, +#endif #if IS_ENABLED(CONFIG_HID_MICROSOFT) { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_COMFORT_MOUSE_4500) }, { HID_USB_DEVICE(USB_VENDOR_ID_MICROSOFT, USB_DEVICE_ID_MS_COMFORT_KEYBOARD) },
MCP2221 is a USB HID to I2C/SMbus host bridge device. This commit implements i2c and smbus host adapter support. 7-bit address and i2c multi-message transaction is also supported. Signed-off-by: Rishi Gupta <gupt21@gmail.com> --- Changes in v2: * added myself in MAINTAINERS for this driver * use macro from hid-ids.h for usb vid and pid * optimize mcp_i2c_write() - less coding * correctly set data length in smbus transaction hid report * added static keyword before int mcp_smbus_xfer() * replace references to silicon labs with microchip Only smbus block/proc is not tested due to lack of appropriate hardware. Rest all is fully tested. MAINTAINERS | 7 + drivers/hid/Kconfig | 10 + drivers/hid/Makefile | 1 + drivers/hid/hid-ids.h | 1 + drivers/hid/hid-mcp2221.c | 756 ++++++++++++++++++++++++++++++++++++++++++++++ drivers/hid/hid-quirks.c | 3 + 6 files changed, 778 insertions(+) create mode 100644 drivers/hid/hid-mcp2221.c