deleted file mode 100644
@@ -1,2752 +0,0 @@
<dropped as otherwise patch is too big>
@@ -491,6 +491,14 @@ config HID_PICOLCD_LEDS
---help---
Provide access to PicoLCD's GPO pins via leds class.
+config HID_PICOLCD_CIR
+ bool "CIR via RC class" if EXPERT
+ default !EXPERT
+ depends on HID_PICOLCD
+ depends on HID_PICOLCD=RC_CORE || RC_CORE=y
+ ---help---
+ Provide access to PicoLCD's CIR interface via remote control (LIRC).
+
config HID_PRIMAX
tristate "Primax non-fully HID-compliant devices"
depends on USB_HID
@@ -66,6 +66,26 @@ obj-$(CONFIG_HID_PRODIKEYS) += hid-prodikeys.o
obj-$(CONFIG_HID_PANTHERLORD) += hid-pl.o
obj-$(CONFIG_HID_PETALYNX) += hid-petalynx.o
obj-$(CONFIG_HID_PICOLCD) += hid-picolcd.o
+hid-picolcd-y += hid-picolcd_core.o
+ifdef CONFIG_HID_PICOLCD_FB
+hid-picolcd-y += hid-picolcd_fb.o
+endif
+ifdef CONFIG_HID_PICOLCD_BACKLIGHT
+hid-picolcd-y += hid-picolcd_backlight.o
+endif
+ifdef CONFIG_HID_PICOLCD_LCD
+hid-picolcd-y += hid-picolcd_lcd.o
+endif
+ifdef CONFIG_HID_PICOLCD_LEDS
+hid-picolcd-y += hid-picolcd_leds.o
+endif
+ifdef CONFIG_HID_PICOLCD_CIR
+hid-picolcd-y += hid-picolcd_cir.o
+endif
+ifdef CONFIG_DEBUG_FS
+hid-picolcd-y += hid-picolcd_debugfs.o
+endif
+
obj-$(CONFIG_HID_PRIMAX) += hid-primax.o
obj-$(CONFIG_HID_ROCCAT) += hid-roccat.o hid-roccat-common.o \
hid-roccat-arvo.o hid-roccat-isku.o hid-roccat-kone.o \
new file mode 100644
@@ -0,0 +1,306 @@
+/***************************************************************************
+ * Copyright (C) 2010-2012 by Bruno Prémont <bonbons@linux-vserver.org> *
+ * *
+ * Based on Logitech G13 driver (v0.4) *
+ * Copyright (C) 2009 by Rick L. Vinyard, Jr. <rvinyard@cs.nmsu.edu> *
+ * *
+ * This program is free software: you can redistribute it and/or modify *
+ * it under the terms of the GNU General Public License as published by *
+ * the Free Software Foundation, version 2 of the License. *
+ * *
+ * This driver is distributed in the hope that it will be useful, but *
+ * WITHOUT ANY WARRANTY; without even the implied warranty of *
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU *
+ * General Public License for more details. *
+ * *
+ * You should have received a copy of the GNU General Public License *
+ * along with this software. If not see <http://www.gnu.org/licenses/>. *
+ ***************************************************************************/
+
+#define PICOLCD_NAME "PicoLCD (graphic)"
+
+/* Report numbers */
+#define REPORT_ERROR_CODE 0x10 /* LCD: IN[16] */
+#define ERR_SUCCESS 0x00
+#define ERR_PARAMETER_MISSING 0x01
+#define ERR_DATA_MISSING 0x02
+#define ERR_BLOCK_READ_ONLY 0x03
+#define ERR_BLOCK_NOT_ERASABLE 0x04
+#define ERR_BLOCK_TOO_BIG 0x05
+#define ERR_SECTION_OVERFLOW 0x06
+#define ERR_INVALID_CMD_LEN 0x07
+#define ERR_INVALID_DATA_LEN 0x08
+#define REPORT_KEY_STATE 0x11 /* LCD: IN[2] */
+#define REPORT_IR_DATA 0x21 /* LCD: IN[63] */
+#define REPORT_EE_DATA 0x32 /* LCD: IN[63] */
+#define REPORT_MEMORY 0x41 /* LCD: IN[63] */
+#define REPORT_LED_STATE 0x81 /* LCD: OUT[1] */
+#define REPORT_BRIGHTNESS 0x91 /* LCD: OUT[1] */
+#define REPORT_CONTRAST 0x92 /* LCD: OUT[1] */
+#define REPORT_RESET 0x93 /* LCD: OUT[2] */
+#define REPORT_LCD_CMD 0x94 /* LCD: OUT[63] */
+#define REPORT_LCD_DATA 0x95 /* LCD: OUT[63] */
+#define REPORT_LCD_CMD_DATA 0x96 /* LCD: OUT[63] */
+#define REPORT_EE_READ 0xa3 /* LCD: OUT[63] */
+#define REPORT_EE_WRITE 0xa4 /* LCD: OUT[63] */
+#define REPORT_ERASE_MEMORY 0xb2 /* LCD: OUT[2] */
+#define REPORT_READ_MEMORY 0xb3 /* LCD: OUT[3] */
+#define REPORT_WRITE_MEMORY 0xb4 /* LCD: OUT[63] */
+#define REPORT_SPLASH_RESTART 0xc1 /* LCD: OUT[1] */
+#define REPORT_EXIT_KEYBOARD 0xef /* LCD: OUT[2] */
+#define REPORT_VERSION 0xf1 /* LCD: IN[2],OUT[1] Bootloader: IN[2],OUT[1] */
+#define REPORT_BL_ERASE_MEMORY 0xf2 /* Bootloader: IN[36],OUT[4] */
+#define REPORT_BL_READ_MEMORY 0xf3 /* Bootloader: IN[36],OUT[4] */
+#define REPORT_BL_WRITE_MEMORY 0xf4 /* Bootloader: IN[36],OUT[36] */
+#define REPORT_DEVID 0xf5 /* LCD: IN[5], OUT[1] Bootloader: IN[5],OUT[1] */
+#define REPORT_SPLASH_SIZE 0xf6 /* LCD: IN[4], OUT[1] */
+#define REPORT_HOOK_VERSION 0xf7 /* LCD: IN[2], OUT[1] */
+#define REPORT_EXIT_FLASHER 0xff /* Bootloader: OUT[2] */
+
+/* Description of in-progress IO operation, used for operations
+ * that trigger response from device */
+struct picolcd_pending {
+ struct hid_report *out_report;
+ struct hid_report *in_report;
+ struct completion ready;
+ int raw_size;
+ u8 raw_data[64];
+};
+
+
+#define PICOLCD_KEYS 17
+
+/* Per device data structure */
+struct picolcd_data {
+ struct hid_device *hdev;
+#ifdef CONFIG_DEBUG_FS
+ struct dentry *debug_reset;
+ struct dentry *debug_eeprom;
+ struct dentry *debug_flash;
+ struct mutex mutex_flash;
+ int addr_sz;
+#endif
+ u8 version[2];
+ unsigned short opmode_delay;
+ /* input stuff */
+ u8 pressed_keys[2];
+ struct input_dev *input_keys;
+ struct input_dev *input_cir;
+ unsigned short keycode[PICOLCD_KEYS];
+
+#ifdef CONFIG_HID_PICOLCD_FB
+ /* Framebuffer stuff */
+ u8 fb_update_rate;
+ u8 fb_bpp;
+ u8 fb_force;
+ u8 *fb_vbitmap; /* local copy of what was sent to PicoLCD */
+ u8 *fb_bitmap; /* framebuffer */
+ struct fb_info *fb_info;
+ struct fb_deferred_io fb_defio;
+#endif /* CONFIG_HID_PICOLCD_FB */
+#ifdef CONFIG_HID_PICOLCD_LCD
+ struct lcd_device *lcd;
+ u8 lcd_contrast;
+#endif /* CONFIG_HID_PICOLCD_LCD */
+#ifdef CONFIG_HID_PICOLCD_BACKLIGHT
+ struct backlight_device *backlight;
+ u8 lcd_brightness;
+ u8 lcd_power;
+#endif /* CONFIG_HID_PICOLCD_BACKLIGHT */
+#ifdef CONFIG_HID_PICOLCD_LEDS
+ /* LED stuff */
+ u8 led_state;
+ struct led_classdev *led[8];
+#endif /* CONFIG_HID_PICOLCD_LEDS */
+
+ /* Housekeeping stuff */
+ spinlock_t lock;
+ struct mutex mutex;
+ struct picolcd_pending *pending;
+ int status;
+#define PICOLCD_BOOTLOADER 1
+#define PICOLCD_FAILED 2
+#define PICOLCD_READY_FB 4
+};
+
+
+/* Find a given report */
+#define picolcd_in_report(id, dev) picolcd_report(id, dev, HID_INPUT_REPORT)
+#define picolcd_out_report(id, dev) picolcd_report(id, dev, HID_OUTPUT_REPORT)
+
+struct hid_report *picolcd_report(int id, struct hid_device *hdev, int dir);
+
+#ifdef CONFIG_DEBUG_FS
+void picolcd_debug_out_report(struct picolcd_data *data,
+ struct hid_device *hdev, struct hid_report *report);
+#define usbhid_submit_report(a, b, c) \
+ do { \
+ picolcd_debug_out_report(hid_get_drvdata(a), a, b); \
+ usbhid_submit_report(a, b, c); \
+ } while (0)
+
+void picolcd_debug_raw_event(struct picolcd_data *data,
+ struct hid_device *hdev, struct hid_report *report,
+ u8 *raw_data, int size);
+
+void picolcd_init_devfs(struct picolcd_data *data,
+ struct hid_report *eeprom_r, struct hid_report *eeprom_w,
+ struct hid_report *flash_r, struct hid_report *flash_w,
+ struct hid_report *reset);
+
+void picolcd_exit_devfs(struct picolcd_data *data);
+#else
+static inline void picolcd_debug_raw_event(struct picolcd_data *data,
+ struct hid_device *hdev, struct hid_report *report,
+ u8 *raw_data, int size)
+{
+}
+static inline void picolcd_init_devfs(struct picolcd_data *data,
+ struct hid_report *eeprom_r, struct hid_report *eeprom_w,
+ struct hid_report *flash_r, struct hid_report *flash_w,
+ struct hid_report *reset)
+{
+}
+static inline void picolcd_exit_devfs(struct picolcd_data *data)
+{
+}
+static inline void picolcd_debug_raw_event(struct picolcd_data *data,
+ struct hid_device *hdev, struct hid_report *report,
+ u8 *raw_data, int size)
+{
+}
+#endif /* CONFIG_DEBUG_FS */
+
+
+#ifdef CONFIG_HID_PICOLCD_FB
+int picolcd_fb_reset(struct picolcd_data *data, int clear);
+
+int picolcd_init_framebuffer(struct picolcd_data *data);
+
+void picolcd_exit_framebuffer(struct picolcd_data *data);
+
+void picolcd_fb_unload(void);
+
+void picolcd_fb_refresh(struct picolcd_data *data);
+#define picolcd_fbinfo(d) ((d)->fb_info)
+#else
+static inline int picolcd_fb_reset(struct picolcd_data *data, int clear)
+{
+ return 0;
+}
+static inline int picolcd_init_framebuffer(struct picolcd_data *data)
+{
+ return 0;
+}
+static inline void picolcd_exit_framebuffer(struct picolcd_data *data)
+{
+}
+static inline void picolcd_fb_unload(void)
+{
+}
+static inline void picolcd_fb_refresh(struct picolcd_data *data)
+{
+}
+#define picolcd_fbinfo(d) NULL
+#endif /* CONFIG_HID_PICOLCD_FB */
+
+
+#ifdef CONFIG_HID_PICOLCD_BACKLIGHT
+int picolcd_init_backlight(struct picolcd_data *data,
+ struct hid_report *report);
+
+void picolcd_exit_backlight(struct picolcd_data *data);
+
+int picolcd_resume_backlight(struct picolcd_data *data);
+
+void picolcd_suspend_backlight(struct picolcd_data *data);
+#else
+static inline int picolcd_init_backlight(struct picolcd_data *data,
+ struct hid_report *report)
+{
+ return 0;
+}
+static inline void picolcd_exit_backlight(struct picolcd_data *data)
+{
+}
+static inline int picolcd_resume_backlight(struct picolcd_data *data)
+{
+ return 0;
+}
+static inline void picolcd_suspend_backlight(struct picolcd_data *data)
+{
+}
+
+#endif /* CONFIG_HID_PICOLCD_BACKLIGHT */
+
+
+#ifdef CONFIG_HID_PICOLCD_LCD
+int picolcd_init_lcd(struct picolcd_data *data,
+ struct hid_report *report);
+
+void picolcd_exit_lcd(struct picolcd_data *data);
+
+int picolcd_resume_lcd(struct picolcd_data *data);
+#else
+static inline int picolcd_init_lcd(struct picolcd_data *data,
+ struct hid_report *report)
+{
+ return 0;
+}
+static inline void picolcd_exit_lcd(struct picolcd_data *data)
+{
+}
+static inline int picolcd_resume_lcd(struct picolcd_data *data)
+{
+ return 0;
+}
+#endif /* CONFIG_HID_PICOLCD_LCD */
+
+
+#ifdef CONFIG_HID_PICOLCD_LEDS
+int picolcd_init_leds(struct picolcd_data *data,
+ struct hid_report *report);
+
+void picolcd_exit_leds(struct picolcd_data *data);
+
+void picolcd_leds_set(struct picolcd_data *data);
+#else
+static inline int picolcd_init_leds(struct picolcd_data *data,
+ struct hid_report *report)
+{
+ return 0;
+}
+static inline void picolcd_exit_leds(struct picolcd_data *data)
+{
+}
+static inline void picolcd_leds_set(struct picolcd_data *data)
+{
+}
+#endif /* CONFIG_HID_PICOLCD_LEDS */
+
+
+#ifdef CONFIG_HID_PICOLCD_CIR
+int picolcd_raw_cir(struct picolcd_data *data,
+ struct hid_report *report, u8 *raw_data, int size);
+
+int picolcd_init_cir(struct picolcd_data *data, struct hid_report *report);
+
+void picolcd_exit_cir(struct picolcd_data *data);
+#else
+static inline int picolcd_raw_cir(struct picolcd_data *data,
+ struct hid_report *report, u8 *raw_data, int size)
+{
+ return 1;
+}
+static inline int picolcd_init_cir(struct picolcd_data *data, struct hid_report *report)
+{
+ return 0;
+}
+static inline void picolcd_exit_cir(struct picolcd_data *data)
+{
+}
+#endif /* CONFIG_HID_PICOLCD_LIRC */
+
+int picolcd_reset(struct hid_device *hdev);
+struct picolcd_pending *picolcd_send_and_wait(struct hid_device *hdev,
+ int report_id, const u8 *raw_data, int size);
new file mode 100644
@@ -0,0 +1,121 @@
+/***************************************************************************
+ * Copyright (C) 2010-2012 by Bruno Prémont <bonbons@linux-vserver.org> *
+ * *
+ * Based on Logitech G13 driver (v0.4) *
+ * Copyright (C) 2009 by Rick L. Vinyard, Jr. <rvinyard@cs.nmsu.edu> *
+ * *
+ * This program is free software: you can redistribute it and/or modify *
+ * it under the terms of the GNU General Public License as published by *
+ * the Free Software Foundation, version 2 of the License. *
+ * *
+ * This driver is distributed in the hope that it will be useful, but *
+ * WITHOUT ANY WARRANTY; without even the implied warranty of *
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU *
+ * General Public License for more details. *
+ * *
+ * You should have received a copy of the GNU General Public License *
+ * along with this software. If not see <http://www.gnu.org/licenses/>. *
+ ***************************************************************************/
+
+#include <linux/hid.h>
+#include "usbhid/usbhid.h"
+#include <linux/usb.h>
+
+#include <linux/fb.h>
+#include <linux/backlight.h>
+
+#include "hid-picolcd.h"
+
+static int picolcd_get_brightness(struct backlight_device *bdev)
+{
+ struct picolcd_data *data = bl_get_data(bdev);
+ return data->lcd_brightness;
+}
+
+static int picolcd_set_brightness(struct backlight_device *bdev)
+{
+ struct picolcd_data *data = bl_get_data(bdev);
+ struct hid_report *report = picolcd_out_report(REPORT_BRIGHTNESS, data->hdev);
+ unsigned long flags;
+
+ if (!report || report->maxfield != 1 || report->field[0]->report_count != 1)
+ return -ENODEV;
+
+ data->lcd_brightness = bdev->props.brightness & 0x0ff;
+ data->lcd_power = bdev->props.power;
+ spin_lock_irqsave(&data->lock, flags);
+ hid_set_field(report->field[0], 0, data->lcd_power == FB_BLANK_UNBLANK ? data->lcd_brightness : 0);
+ usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+ spin_unlock_irqrestore(&data->lock, flags);
+ return 0;
+}
+
+static int picolcd_check_bl_fb(struct backlight_device *bdev, struct fb_info *fb)
+{
+ return fb && fb == picolcd_fbinfo((struct picolcd_data *)bl_get_data(bdev));
+}
+
+static const struct backlight_ops picolcd_blops = {
+ .update_status = picolcd_set_brightness,
+ .get_brightness = picolcd_get_brightness,
+ .check_fb = picolcd_check_bl_fb,
+};
+
+int picolcd_init_backlight(struct picolcd_data *data, struct hid_report *report)
+{
+ struct device *dev = &data->hdev->dev;
+ struct backlight_device *bdev;
+ struct backlight_properties props;
+ if (!report)
+ return -ENODEV;
+ if (report->maxfield != 1 || report->field[0]->report_count != 1 ||
+ report->field[0]->report_size != 8) {
+ dev_err(dev, "unsupported BRIGHTNESS report");
+ return -EINVAL;
+ }
+
+ memset(&props, 0, sizeof(props));
+ props.type = BACKLIGHT_RAW;
+ props.max_brightness = 0xff;
+ bdev = backlight_device_register(dev_name(dev), dev, data,
+ &picolcd_blops, &props);
+ if (IS_ERR(bdev)) {
+ dev_err(dev, "failed to register backlight\n");
+ return PTR_ERR(bdev);
+ }
+ bdev->props.brightness = 0xff;
+ data->lcd_brightness = 0xff;
+ data->backlight = bdev;
+ picolcd_set_brightness(bdev);
+ return 0;
+}
+
+void picolcd_exit_backlight(struct picolcd_data *data)
+{
+ struct backlight_device *bdev = data->backlight;
+
+ data->backlight = NULL;
+ if (bdev)
+ backlight_device_unregister(bdev);
+}
+
+int picolcd_resume_backlight(struct picolcd_data *data)
+{
+ if (!data->backlight)
+ return 0;
+ return picolcd_set_brightness(data->backlight);
+}
+
+#ifdef CONFIG_PM
+void picolcd_suspend_backlight(struct picolcd_data *data)
+{
+ int bl_power = data->lcd_power;
+ if (!data->backlight)
+ return;
+
+ data->backlight->props.power = FB_BLANK_POWERDOWN;
+ picolcd_set_brightness(data->backlight);
+ data->lcd_power = data->backlight->props.power = bl_power;
+}
+#endif /* CONFIG_PM */
+
new file mode 100644
@@ -0,0 +1,61 @@
+/***************************************************************************
+ * Copyright (C) 2010-2012 by Bruno Prémont <bonbons@linux-vserver.org> *
+ * *
+ * Based on Logitech G13 driver (v0.4) *
+ * Copyright (C) 2009 by Rick L. Vinyard, Jr. <rvinyard@cs.nmsu.edu> *
+ * *
+ * This program is free software: you can redistribute it and/or modify *
+ * it under the terms of the GNU General Public License as published by *
+ * the Free Software Foundation, version 2 of the License. *
+ * *
+ * This driver is distributed in the hope that it will be useful, but *
+ * WITHOUT ANY WARRANTY; without even the implied warranty of *
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU *
+ * General Public License for more details. *
+ * *
+ * You should have received a copy of the GNU General Public License *
+ * along with this software. If not see <http://www.gnu.org/licenses/>. *
+ ***************************************************************************/
+
+#include <linux/hid.h>
+#include <linux/hid-debug.h>
+#include <linux/input.h>
+#include "hid-ids.h"
+#include "usbhid/usbhid.h"
+#include <linux/usb.h>
+
+#include <linux/fb.h>
+#include <linux/vmalloc.h>
+#include <linux/backlight.h>
+#include <linux/lcd.h>
+
+#include <linux/leds.h>
+
+#include <linux/seq_file.h>
+#include <linux/debugfs.h>
+
+#include <linux/completion.h>
+#include <linux/uaccess.h>
+#include <linux/module.h>
+
+#include "hid-picolcd.h"
+
+
+int picolcd_raw_cir(struct picolcd_data *data,
+ struct hid_report *report, u8 *raw_data, int size)
+{
+ /* Need understanding of CIR data format to implement ... */
+ return 1;
+}
+
+/* initialize CIR input device */
+int picolcd_init_cir(struct picolcd_data *data, struct hid_report *report)
+{
+ /* support not implemented yet */
+ return 0;
+}
+
+void picolcd_exit_cir(struct picolcd_data *data)
+{
+}
+
new file mode 100644
@@ -0,0 +1,704 @@
+/***************************************************************************
+ * Copyright (C) 2010-2012 by Bruno Prémont <bonbons@linux-vserver.org> *
+ * *
+ * Based on Logitech G13 driver (v0.4) *
+ * Copyright (C) 2009 by Rick L. Vinyard, Jr. <rvinyard@cs.nmsu.edu> *
+ * *
+ * This program is free software: you can redistribute it and/or modify *
+ * it under the terms of the GNU General Public License as published by *
+ * the Free Software Foundation, version 2 of the License. *
+ * *
+ * This driver is distributed in the hope that it will be useful, but *
+ * WITHOUT ANY WARRANTY; without even the implied warranty of *
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU *
+ * General Public License for more details. *
+ * *
+ * You should have received a copy of the GNU General Public License *
+ * along with this software. If not see <http://www.gnu.org/licenses/>. *
+ ***************************************************************************/
+
+#include <linux/hid.h>
+#include <linux/hid-debug.h>
+#include <linux/input.h>
+#include "hid-ids.h"
+#include "usbhid/usbhid.h"
+#include <linux/usb.h>
+
+#include <linux/fb.h>
+#include <linux/vmalloc.h>
+
+#include <linux/completion.h>
+#include <linux/uaccess.h>
+#include <linux/module.h>
+
+#include "hid-picolcd.h"
+
+
+/* Input device
+ *
+ * The PicoLCD has an IR receiver header, a built-in keypad with 5 keys
+ * and header for 4x4 key matrix. The built-in keys are part of the matrix.
+ */
+static const unsigned short def_keymap[PICOLCD_KEYS] = {
+ KEY_RESERVED, /* none */
+ KEY_BACK, /* col 4 + row 1 */
+ KEY_HOMEPAGE, /* col 3 + row 1 */
+ KEY_RESERVED, /* col 2 + row 1 */
+ KEY_RESERVED, /* col 1 + row 1 */
+ KEY_SCROLLUP, /* col 4 + row 2 */
+ KEY_OK, /* col 3 + row 2 */
+ KEY_SCROLLDOWN, /* col 2 + row 2 */
+ KEY_RESERVED, /* col 1 + row 2 */
+ KEY_RESERVED, /* col 4 + row 3 */
+ KEY_RESERVED, /* col 3 + row 3 */
+ KEY_RESERVED, /* col 2 + row 3 */
+ KEY_RESERVED, /* col 1 + row 3 */
+ KEY_RESERVED, /* col 4 + row 4 */
+ KEY_RESERVED, /* col 3 + row 4 */
+ KEY_RESERVED, /* col 2 + row 4 */
+ KEY_RESERVED, /* col 1 + row 4 */
+};
+
+
+/* Find a given report */
+struct hid_report *picolcd_report(int id, struct hid_device *hdev, int dir)
+{
+ struct list_head *feature_report_list = &hdev->report_enum[dir].report_list;
+ struct hid_report *report = NULL;
+
+ list_for_each_entry(report, feature_report_list, list) {
+ if (report->id == id)
+ return report;
+ }
+ hid_warn(hdev, "No report with id 0x%x found\n", id);
+ return NULL;
+}
+
+/* Submit a report and wait for a reply from device - if device fades away
+ * or does not respond in time, return NULL */
+struct picolcd_pending *picolcd_send_and_wait(struct hid_device *hdev,
+ int report_id, const u8 *raw_data, int size)
+{
+ struct picolcd_data *data = hid_get_drvdata(hdev);
+ struct picolcd_pending *work;
+ struct hid_report *report = picolcd_out_report(report_id, hdev);
+ unsigned long flags;
+ int i, j, k;
+
+ if (!report || !data)
+ return NULL;
+ if (data->status & PICOLCD_FAILED)
+ return NULL;
+ work = kzalloc(sizeof(*work), GFP_KERNEL);
+ if (!work)
+ return NULL;
+
+ init_completion(&work->ready);
+ work->out_report = report;
+ work->in_report = NULL;
+ work->raw_size = 0;
+
+ mutex_lock(&data->mutex);
+ spin_lock_irqsave(&data->lock, flags);
+ for (i = k = 0; i < report->maxfield; i++)
+ for (j = 0; j < report->field[i]->report_count; j++) {
+ hid_set_field(report->field[i], j, k < size ? raw_data[k] : 0);
+ k++;
+ }
+ data->pending = work;
+ usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+ spin_unlock_irqrestore(&data->lock, flags);
+ wait_for_completion_interruptible_timeout(&work->ready, HZ*2);
+ spin_lock_irqsave(&data->lock, flags);
+ data->pending = NULL;
+ spin_unlock_irqrestore(&data->lock, flags);
+ mutex_unlock(&data->mutex);
+ return work;
+}
+
+/*
+ * input class device
+ */
+static int picolcd_raw_keypad(struct picolcd_data *data,
+ struct hid_report *report, u8 *raw_data, int size)
+{
+ /*
+ * Keypad event
+ * First and second data bytes list currently pressed keys,
+ * 0x00 means no key and at most 2 keys may be pressed at same time
+ */
+ int i, j;
+
+ /* determine newly pressed keys */
+ for (i = 0; i < size; i++) {
+ unsigned int key_code;
+ if (raw_data[i] == 0)
+ continue;
+ for (j = 0; j < sizeof(data->pressed_keys); j++)
+ if (data->pressed_keys[j] == raw_data[i])
+ goto key_already_down;
+ for (j = 0; j < sizeof(data->pressed_keys); j++)
+ if (data->pressed_keys[j] == 0) {
+ data->pressed_keys[j] = raw_data[i];
+ break;
+ }
+ input_event(data->input_keys, EV_MSC, MSC_SCAN, raw_data[i]);
+ if (raw_data[i] < PICOLCD_KEYS)
+ key_code = data->keycode[raw_data[i]];
+ else
+ key_code = KEY_UNKNOWN;
+ if (key_code != KEY_UNKNOWN) {
+ dbg_hid(PICOLCD_NAME " got key press for %u:%d",
+ raw_data[i], key_code);
+ input_report_key(data->input_keys, key_code, 1);
+ }
+ input_sync(data->input_keys);
+key_already_down:
+ continue;
+ }
+
+ /* determine newly released keys */
+ for (j = 0; j < sizeof(data->pressed_keys); j++) {
+ unsigned int key_code;
+ if (data->pressed_keys[j] == 0)
+ continue;
+ for (i = 0; i < size; i++)
+ if (data->pressed_keys[j] == raw_data[i])
+ goto key_still_down;
+ input_event(data->input_keys, EV_MSC, MSC_SCAN, data->pressed_keys[j]);
+ if (data->pressed_keys[j] < PICOLCD_KEYS)
+ key_code = data->keycode[data->pressed_keys[j]];
+ else
+ key_code = KEY_UNKNOWN;
+ if (key_code != KEY_UNKNOWN) {
+ dbg_hid(PICOLCD_NAME " got key release for %u:%d",
+ data->pressed_keys[j], key_code);
+ input_report_key(data->input_keys, key_code, 0);
+ }
+ input_sync(data->input_keys);
+ data->pressed_keys[j] = 0;
+key_still_down:
+ continue;
+ }
+ return 1;
+}
+
+static int picolcd_check_version(struct hid_device *hdev)
+{
+ struct picolcd_data *data = hid_get_drvdata(hdev);
+ struct picolcd_pending *verinfo;
+ int ret = 0;
+
+ if (!data)
+ return -ENODEV;
+
+ verinfo = picolcd_send_and_wait(hdev, REPORT_VERSION, NULL, 0);
+ if (!verinfo) {
+ hid_err(hdev, "no version response from PicoLCD\n");
+ return -ENODEV;
+ }
+
+ if (verinfo->raw_size == 2) {
+ data->version[0] = verinfo->raw_data[1];
+ data->version[1] = verinfo->raw_data[0];
+ if (data->status & PICOLCD_BOOTLOADER) {
+ hid_info(hdev, "PicoLCD, bootloader version %d.%d\n",
+ verinfo->raw_data[1], verinfo->raw_data[0]);
+ } else {
+ hid_info(hdev, "PicoLCD, firmware version %d.%d\n",
+ verinfo->raw_data[1], verinfo->raw_data[0]);
+ }
+ } else {
+ hid_err(hdev, "confused, got unexpected version response from PicoLCD\n");
+ ret = -EINVAL;
+ }
+ kfree(verinfo);
+ return ret;
+}
+
+/*
+ * Reset our device and wait for answer to VERSION request
+ */
+int picolcd_reset(struct hid_device *hdev)
+{
+ struct picolcd_data *data = hid_get_drvdata(hdev);
+ struct hid_report *report = picolcd_out_report(REPORT_RESET, hdev);
+ unsigned long flags;
+ int error;
+
+ if (!data || !report || report->maxfield != 1)
+ return -ENODEV;
+
+ spin_lock_irqsave(&data->lock, flags);
+ if (hdev->product == USB_DEVICE_ID_PICOLCD_BOOTLOADER)
+ data->status |= PICOLCD_BOOTLOADER;
+
+ /* perform the reset */
+ hid_set_field(report->field[0], 0, 1);
+ usbhid_submit_report(hdev, report, USB_DIR_OUT);
+ spin_unlock_irqrestore(&data->lock, flags);
+
+ error = picolcd_check_version(hdev);
+ if (error)
+ return error;
+
+ picolcd_resume_lcd(data);
+ picolcd_resume_backlight(data);
+ picolcd_fb_refresh(data);
+ picolcd_leds_set(data);
+ return 0;
+}
+
+/*
+ * The "operation_mode" sysfs attribute
+ */
+static ssize_t picolcd_operation_mode_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct picolcd_data *data = dev_get_drvdata(dev);
+
+ if (data->status & PICOLCD_BOOTLOADER)
+ return snprintf(buf, PAGE_SIZE, "[bootloader] lcd\n");
+ else
+ return snprintf(buf, PAGE_SIZE, "bootloader [lcd]\n");
+}
+
+static ssize_t picolcd_operation_mode_store(struct device *dev,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ struct picolcd_data *data = dev_get_drvdata(dev);
+ struct hid_report *report = NULL;
+ size_t cnt = count;
+ int timeout = data->opmode_delay;
+ unsigned long flags;
+
+ if (cnt >= 3 && strncmp("lcd", buf, 3) == 0) {
+ if (data->status & PICOLCD_BOOTLOADER)
+ report = picolcd_out_report(REPORT_EXIT_FLASHER, data->hdev);
+ buf += 3;
+ cnt -= 3;
+ } else if (cnt >= 10 && strncmp("bootloader", buf, 10) == 0) {
+ if (!(data->status & PICOLCD_BOOTLOADER))
+ report = picolcd_out_report(REPORT_EXIT_KEYBOARD, data->hdev);
+ buf += 10;
+ cnt -= 10;
+ }
+ if (!report)
+ return -EINVAL;
+
+ while (cnt > 0 && (buf[cnt-1] == '\n' || buf[cnt-1] == '\r'))
+ cnt--;
+ if (cnt != 0)
+ return -EINVAL;
+
+ spin_lock_irqsave(&data->lock, flags);
+ hid_set_field(report->field[0], 0, timeout & 0xff);
+ hid_set_field(report->field[0], 1, (timeout >> 8) & 0xff);
+ usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+ spin_unlock_irqrestore(&data->lock, flags);
+ return count;
+}
+
+static DEVICE_ATTR(operation_mode, 0644, picolcd_operation_mode_show,
+ picolcd_operation_mode_store);
+
+/*
+ * The "operation_mode_delay" sysfs attribute
+ */
+static ssize_t picolcd_operation_mode_delay_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct picolcd_data *data = dev_get_drvdata(dev);
+
+ return snprintf(buf, PAGE_SIZE, "%hu\n", data->opmode_delay);
+}
+
+static ssize_t picolcd_operation_mode_delay_store(struct device *dev,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ struct picolcd_data *data = dev_get_drvdata(dev);
+ unsigned u;
+ if (sscanf(buf, "%u", &u) != 1)
+ return -EINVAL;
+ if (u > 30000)
+ return -EINVAL;
+ else
+ data->opmode_delay = u;
+ return count;
+}
+
+static DEVICE_ATTR(operation_mode_delay, 0644, picolcd_operation_mode_delay_show,
+ picolcd_operation_mode_delay_store);
+
+/*
+ * Handle raw report as sent by device
+ */
+static int picolcd_raw_event(struct hid_device *hdev,
+ struct hid_report *report, u8 *raw_data, int size)
+{
+ struct picolcd_data *data = hid_get_drvdata(hdev);
+ unsigned long flags;
+ int ret = 0;
+
+ if (!data)
+ return 1;
+
+ if (report->id == REPORT_KEY_STATE) {
+ if (data->input_keys)
+ ret = picolcd_raw_keypad(data, report, raw_data+1, size-1);
+ } else if (report->id == REPORT_IR_DATA) {
+ if (data->input_cir)
+ ret = picolcd_raw_cir(data, report, raw_data+1, size-1);
+ } else {
+ spin_lock_irqsave(&data->lock, flags);
+ /*
+ * We let the caller of picolcd_send_and_wait() check if the
+ * report we got is one of the expected ones or not.
+ */
+ if (data->pending) {
+ memcpy(data->pending->raw_data, raw_data+1, size-1);
+ data->pending->raw_size = size-1;
+ data->pending->in_report = report;
+ complete(&data->pending->ready);
+ }
+ spin_unlock_irqrestore(&data->lock, flags);
+ }
+
+ picolcd_debug_raw_event(data, hdev, report, raw_data, size);
+ return 1;
+}
+
+#ifdef CONFIG_PM
+static int picolcd_suspend(struct hid_device *hdev, pm_message_t message)
+{
+ if (PMSG_IS_AUTO(message))
+ return 0;
+
+ picolcd_suspend_backlight(hid_get_drvdata(hdev));
+ dbg_hid(PICOLCD_NAME " device ready for suspend\n");
+ return 0;
+}
+
+static int picolcd_resume(struct hid_device *hdev)
+{
+ int ret;
+ ret = picolcd_resume_backlight(hid_get_drvdata(hdev));
+ if (ret)
+ dbg_hid(PICOLCD_NAME " restoring backlight failed: %d\n", ret);
+ return 0;
+}
+
+static int picolcd_reset_resume(struct hid_device *hdev)
+{
+ int ret;
+ ret = picolcd_reset(hdev);
+ if (ret)
+ dbg_hid(PICOLCD_NAME " resetting our device failed: %d\n", ret);
+ ret = picolcd_fb_reset(hid_get_drvdata(hdev), 0);
+ if (ret)
+ dbg_hid(PICOLCD_NAME " restoring framebuffer content failed: %d\n", ret);
+ ret = picolcd_resume_lcd(hid_get_drvdata(hdev));
+ if (ret)
+ dbg_hid(PICOLCD_NAME " restoring lcd failed: %d\n", ret);
+ ret = picolcd_resume_backlight(hid_get_drvdata(hdev));
+ if (ret)
+ dbg_hid(PICOLCD_NAME " restoring backlight failed: %d\n", ret);
+ picolcd_leds_set(hid_get_drvdata(hdev));
+ return 0;
+}
+#endif
+
+/* initialize keypad input device */
+static int picolcd_init_keys(struct picolcd_data *data,
+ struct hid_report *report)
+{
+ struct hid_device *hdev = data->hdev;
+ struct input_dev *idev;
+ int error, i;
+
+ if (!report)
+ return -ENODEV;
+ if (report->maxfield != 1 || report->field[0]->report_count != 2 ||
+ report->field[0]->report_size != 8) {
+ hid_err(hdev, "unsupported KEY_STATE report\n");
+ return -EINVAL;
+ }
+
+ idev = input_allocate_device();
+ if (idev == NULL) {
+ hid_err(hdev, "failed to allocate input device\n");
+ return -ENOMEM;
+ }
+ input_set_drvdata(idev, hdev);
+ memcpy(data->keycode, def_keymap, sizeof(def_keymap));
+ idev->name = hdev->name;
+ idev->phys = hdev->phys;
+ idev->uniq = hdev->uniq;
+ idev->id.bustype = hdev->bus;
+ idev->id.vendor = hdev->vendor;
+ idev->id.product = hdev->product;
+ idev->id.version = hdev->version;
+ idev->dev.parent = hdev->dev.parent;
+ idev->keycode = &data->keycode;
+ idev->keycodemax = PICOLCD_KEYS;
+ idev->keycodesize = sizeof(data->keycode[0]);
+ input_set_capability(idev, EV_MSC, MSC_SCAN);
+ set_bit(EV_REP, idev->evbit);
+ for (i = 0; i < PICOLCD_KEYS; i++)
+ input_set_capability(idev, EV_KEY, data->keycode[i]);
+ error = input_register_device(idev);
+ if (error) {
+ hid_err(hdev, "error registering the input device\n");
+ input_free_device(idev);
+ return error;
+ }
+ data->input_keys = idev;
+ return 0;
+}
+
+static void picolcd_exit_keys(struct picolcd_data *data)
+{
+ struct input_dev *idev = data->input_keys;
+
+ data->input_keys = NULL;
+ if (idev)
+ input_unregister_device(idev);
+}
+
+static int picolcd_probe_lcd(struct hid_device *hdev, struct picolcd_data *data)
+{
+ int error;
+
+ error = picolcd_check_version(hdev);
+ if (error)
+ return error;
+
+ if (data->version[0] != 0 && data->version[1] != 3)
+ hid_info(hdev, "Device with untested firmware revision, please submit /sys/kernel/debug/hid/%s/rdesc for this device.\n",
+ dev_name(&hdev->dev));
+
+ /* Setup keypad input device */
+ error = picolcd_init_keys(data, picolcd_in_report(REPORT_KEY_STATE, hdev));
+ if (error)
+ goto err;
+
+ /* Setup CIR input device */
+ error = picolcd_init_cir(data, picolcd_in_report(REPORT_IR_DATA, hdev));
+ if (error)
+ goto err;
+
+ /* Set up the framebuffer device */
+ error = picolcd_init_framebuffer(data);
+ if (error)
+ goto err;
+
+ /* Setup lcd class device */
+ error = picolcd_init_lcd(data, picolcd_out_report(REPORT_CONTRAST, hdev));
+ if (error)
+ goto err;
+
+ /* Setup backlight class device */
+ error = picolcd_init_backlight(data, picolcd_out_report(REPORT_BRIGHTNESS, hdev));
+ if (error)
+ goto err;
+
+ /* Setup the LED class devices */
+ error = picolcd_init_leds(data, picolcd_out_report(REPORT_LED_STATE, hdev));
+ if (error)
+ goto err;
+
+ picolcd_init_devfs(data, picolcd_out_report(REPORT_EE_READ, hdev),
+ picolcd_out_report(REPORT_EE_WRITE, hdev),
+ picolcd_out_report(REPORT_READ_MEMORY, hdev),
+ picolcd_out_report(REPORT_WRITE_MEMORY, hdev),
+ picolcd_out_report(REPORT_RESET, hdev));
+ return 0;
+err:
+ picolcd_exit_leds(data);
+ picolcd_exit_backlight(data);
+ picolcd_exit_lcd(data);
+ picolcd_exit_framebuffer(data);
+ picolcd_exit_cir(data);
+ picolcd_exit_keys(data);
+ return error;
+}
+
+static int picolcd_probe_bootloader(struct hid_device *hdev, struct picolcd_data *data)
+{
+ int error;
+
+ error = picolcd_check_version(hdev);
+ if (error)
+ return error;
+
+ if (data->version[0] != 1 && data->version[1] != 0)
+ hid_info(hdev, "Device with untested bootloader revision, please submit /sys/kernel/debug/hid/%s/rdesc for this device.\n",
+ dev_name(&hdev->dev));
+
+ picolcd_init_devfs(data, NULL, NULL,
+ picolcd_out_report(REPORT_BL_READ_MEMORY, hdev),
+ picolcd_out_report(REPORT_BL_WRITE_MEMORY, hdev), NULL);
+ return 0;
+}
+
+static int picolcd_probe(struct hid_device *hdev,
+ const struct hid_device_id *id)
+{
+ struct picolcd_data *data;
+ int error = -ENOMEM;
+
+ dbg_hid(PICOLCD_NAME " hardware probe...\n");
+
+ /*
+ * Let's allocate the picolcd data structure, set some reasonable
+ * defaults, and associate it with the device
+ */
+ data = kzalloc(sizeof(struct picolcd_data), GFP_KERNEL);
+ if (data == NULL) {
+ hid_err(hdev, "can't allocate space for Minibox PicoLCD device data\n");
+ error = -ENOMEM;
+ goto err_no_cleanup;
+ }
+
+ spin_lock_init(&data->lock);
+ mutex_init(&data->mutex);
+ data->hdev = hdev;
+ data->opmode_delay = 5000;
+ if (hdev->product == USB_DEVICE_ID_PICOLCD_BOOTLOADER)
+ data->status |= PICOLCD_BOOTLOADER;
+ hid_set_drvdata(hdev, data);
+
+ /* Parse the device reports and start it up */
+ error = hid_parse(hdev);
+ if (error) {
+ hid_err(hdev, "device report parse failed\n");
+ goto err_cleanup_data;
+ }
+
+ /* We don't use hidinput but hid_hw_start() fails if nothing is
+ * claimed. So spoof claimed input. */
+ hdev->claimed = HID_CLAIMED_INPUT;
+ error = hid_hw_start(hdev, 0);
+ hdev->claimed = 0;
+ if (error) {
+ hid_err(hdev, "hardware start failed\n");
+ goto err_cleanup_data;
+ }
+
+ error = hid_hw_open(hdev);
+ if (error) {
+ hid_err(hdev, "failed to open input interrupt pipe for key and IR events\n");
+ goto err_cleanup_hid_hw;
+ }
+
+ error = device_create_file(&hdev->dev, &dev_attr_operation_mode_delay);
+ if (error) {
+ hid_err(hdev, "failed to create sysfs attributes\n");
+ goto err_cleanup_hid_ll;
+ }
+
+ error = device_create_file(&hdev->dev, &dev_attr_operation_mode);
+ if (error) {
+ hid_err(hdev, "failed to create sysfs attributes\n");
+ goto err_cleanup_sysfs1;
+ }
+
+ if (data->status & PICOLCD_BOOTLOADER)
+ error = picolcd_probe_bootloader(hdev, data);
+ else
+ error = picolcd_probe_lcd(hdev, data);
+ if (error)
+ goto err_cleanup_sysfs2;
+
+ dbg_hid(PICOLCD_NAME " activated and initialized\n");
+ return 0;
+
+err_cleanup_sysfs2:
+ device_remove_file(&hdev->dev, &dev_attr_operation_mode);
+err_cleanup_sysfs1:
+ device_remove_file(&hdev->dev, &dev_attr_operation_mode_delay);
+err_cleanup_hid_ll:
+ hid_hw_close(hdev);
+err_cleanup_hid_hw:
+ hid_hw_stop(hdev);
+err_cleanup_data:
+ kfree(data);
+err_no_cleanup:
+ hid_set_drvdata(hdev, NULL);
+
+ return error;
+}
+
+static void picolcd_remove(struct hid_device *hdev)
+{
+ struct picolcd_data *data = hid_get_drvdata(hdev);
+ unsigned long flags;
+
+ dbg_hid(PICOLCD_NAME " hardware remove...\n");
+ spin_lock_irqsave(&data->lock, flags);
+ data->status |= PICOLCD_FAILED;
+ spin_unlock_irqrestore(&data->lock, flags);
+
+ picolcd_exit_devfs(data);
+ device_remove_file(&hdev->dev, &dev_attr_operation_mode);
+ device_remove_file(&hdev->dev, &dev_attr_operation_mode_delay);
+ hid_hw_close(hdev);
+ hid_hw_stop(hdev);
+ hid_set_drvdata(hdev, NULL);
+
+ /* Shortcut potential pending reply that will never arrive */
+ spin_lock_irqsave(&data->lock, flags);
+ if (data->pending)
+ complete(&data->pending->ready);
+ spin_unlock_irqrestore(&data->lock, flags);
+
+ /* Cleanup LED */
+ picolcd_exit_leds(data);
+ /* Clean up the framebuffer */
+ picolcd_exit_backlight(data);
+ picolcd_exit_lcd(data);
+ picolcd_exit_framebuffer(data);
+ /* Cleanup input */
+ picolcd_exit_cir(data);
+ picolcd_exit_keys(data);
+
+ mutex_destroy(&data->mutex);
+ /* Finally, clean up the picolcd data itself */
+ kfree(data);
+}
+
+static const struct hid_device_id picolcd_devices[] = {
+ { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD) },
+ { HID_USB_DEVICE(USB_VENDOR_ID_MICROCHIP, USB_DEVICE_ID_PICOLCD_BOOTLOADER) },
+ { }
+};
+MODULE_DEVICE_TABLE(hid, picolcd_devices);
+
+static struct hid_driver picolcd_driver = {
+ .name = "hid-picolcd",
+ .id_table = picolcd_devices,
+ .probe = picolcd_probe,
+ .remove = picolcd_remove,
+ .raw_event = picolcd_raw_event,
+#ifdef CONFIG_PM
+ .suspend = picolcd_suspend,
+ .resume = picolcd_resume,
+ .reset_resume = picolcd_reset_resume,
+#endif
+};
+
+static int __init picolcd_init(void)
+{
+ return hid_register_driver(&picolcd_driver);
+}
+
+static void __exit picolcd_exit(void)
+{
+ hid_unregister_driver(&picolcd_driver);
+ picolcd_fb_unload();
+}
+
+module_init(picolcd_init);
+module_exit(picolcd_exit);
+MODULE_DESCRIPTION("Minibox graphics PicoLCD Driver");
+MODULE_LICENSE("GPL v2");
new file mode 100644
@@ -0,0 +1,898 @@
+/***************************************************************************
+ * Copyright (C) 2010-2012 by Bruno Prémont <bonbons@linux-vserver.org> *
+ * *
+ * Based on Logitech G13 driver (v0.4) *
+ * Copyright (C) 2009 by Rick L. Vinyard, Jr. <rvinyard@cs.nmsu.edu> *
+ * *
+ * This program is free software: you can redistribute it and/or modify *
+ * it under the terms of the GNU General Public License as published by *
+ * the Free Software Foundation, version 2 of the License. *
+ * *
+ * This driver is distributed in the hope that it will be useful, but *
+ * WITHOUT ANY WARRANTY; without even the implied warranty of *
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU *
+ * General Public License for more details. *
+ * *
+ * You should have received a copy of the GNU General Public License *
+ * along with this software. If not see <http://www.gnu.org/licenses/>. *
+ ***************************************************************************/
+
+#include <linux/hid.h>
+#include <linux/hid-debug.h>
+#include "usbhid/usbhid.h"
+#include <linux/usb.h>
+
+#include <linux/fb.h>
+#include <linux/seq_file.h>
+#include <linux/debugfs.h>
+
+#include <linux/module.h>
+
+#include "hid-picolcd.h"
+
+
+static int picolcd_debug_reset_show(struct seq_file *f, void *p)
+{
+ if (picolcd_fbinfo((struct picolcd_data *)f->private))
+ seq_printf(f, "all fb\n");
+ else
+ seq_printf(f, "all\n");
+ return 0;
+}
+
+static int picolcd_debug_reset_open(struct inode *inode, struct file *f)
+{
+ return single_open(f, picolcd_debug_reset_show, inode->i_private);
+}
+
+static ssize_t picolcd_debug_reset_write(struct file *f, const char __user *user_buf,
+ size_t count, loff_t *ppos)
+{
+ struct picolcd_data *data = ((struct seq_file *)f->private_data)->private;
+ char buf[32];
+ size_t cnt = min(count, sizeof(buf)-1);
+ if (copy_from_user(buf, user_buf, cnt))
+ return -EFAULT;
+
+ while (cnt > 0 && (buf[cnt-1] == ' ' || buf[cnt-1] == '\n'))
+ cnt--;
+ buf[cnt] = '\0';
+ if (strcmp(buf, "all") == 0) {
+ picolcd_reset(data->hdev);
+ picolcd_fb_reset(data, 1);
+ } else if (strcmp(buf, "fb") == 0) {
+ picolcd_fb_reset(data, 1);
+ } else {
+ return -EINVAL;
+ }
+ return count;
+}
+
+static const struct file_operations picolcd_debug_reset_fops = {
+ .owner = THIS_MODULE,
+ .open = picolcd_debug_reset_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .write = picolcd_debug_reset_write,
+ .release = single_release,
+};
+
+/*
+ * The "eeprom" file
+ */
+static ssize_t picolcd_debug_eeprom_read(struct file *f, char __user *u,
+ size_t s, loff_t *off)
+{
+ struct picolcd_data *data = f->private_data;
+ struct picolcd_pending *resp;
+ u8 raw_data[3];
+ ssize_t ret = -EIO;
+
+ if (s == 0)
+ return -EINVAL;
+ if (*off > 0x0ff)
+ return 0;
+
+ /* prepare buffer with info about what we want to read (addr & len) */
+ raw_data[0] = *off & 0xff;
+ raw_data[1] = (*off >> 8) & 0xff;
+ raw_data[2] = s < 20 ? s : 20;
+ if (*off + raw_data[2] > 0xff)
+ raw_data[2] = 0x100 - *off;
+ resp = picolcd_send_and_wait(data->hdev, REPORT_EE_READ, raw_data,
+ sizeof(raw_data));
+ if (!resp)
+ return -EIO;
+
+ if (resp->in_report && resp->in_report->id == REPORT_EE_DATA) {
+ /* successful read :) */
+ ret = resp->raw_data[2];
+ if (ret > s)
+ ret = s;
+ if (copy_to_user(u, resp->raw_data+3, ret))
+ ret = -EFAULT;
+ else
+ *off += ret;
+ } /* anything else is some kind of IO error */
+
+ kfree(resp);
+ return ret;
+}
+
+static ssize_t picolcd_debug_eeprom_write(struct file *f, const char __user *u,
+ size_t s, loff_t *off)
+{
+ struct picolcd_data *data = f->private_data;
+ struct picolcd_pending *resp;
+ ssize_t ret = -EIO;
+ u8 raw_data[23];
+
+ if (s == 0)
+ return -EINVAL;
+ if (*off > 0x0ff)
+ return -ENOSPC;
+
+ memset(raw_data, 0, sizeof(raw_data));
+ raw_data[0] = *off & 0xff;
+ raw_data[1] = (*off >> 8) & 0xff;
+ raw_data[2] = min((size_t)20, s);
+ if (*off + raw_data[2] > 0xff)
+ raw_data[2] = 0x100 - *off;
+
+ if (copy_from_user(raw_data+3, u, min((u8)20, raw_data[2])))
+ return -EFAULT;
+ resp = picolcd_send_and_wait(data->hdev, REPORT_EE_WRITE, raw_data,
+ sizeof(raw_data));
+
+ if (!resp)
+ return -EIO;
+
+ if (resp->in_report && resp->in_report->id == REPORT_EE_DATA) {
+ /* check if written data matches */
+ if (memcmp(raw_data, resp->raw_data, 3+raw_data[2]) == 0) {
+ *off += raw_data[2];
+ ret = raw_data[2];
+ }
+ }
+ kfree(resp);
+ return ret;
+}
+
+/*
+ * Notes:
+ * - read/write happens in chunks of at most 20 bytes, it's up to userspace
+ * to loop in order to get more data.
+ * - on write errors on otherwise correct write request the bytes
+ * that should have been written are in undefined state.
+ */
+static const struct file_operations picolcd_debug_eeprom_fops = {
+ .owner = THIS_MODULE,
+ .open = simple_open,
+ .read = picolcd_debug_eeprom_read,
+ .write = picolcd_debug_eeprom_write,
+ .llseek = generic_file_llseek,
+};
+
+/*
+ * The "flash" file
+ */
+/* record a flash address to buf (bounds check to be done by caller) */
+static int _picolcd_flash_setaddr(struct picolcd_data *data, u8 *buf, long off)
+{
+ buf[0] = off & 0xff;
+ buf[1] = (off >> 8) & 0xff;
+ if (data->addr_sz == 3)
+ buf[2] = (off >> 16) & 0xff;
+ return data->addr_sz == 2 ? 2 : 3;
+}
+
+/* read a given size of data (bounds check to be done by caller) */
+static ssize_t _picolcd_flash_read(struct picolcd_data *data, int report_id,
+ char __user *u, size_t s, loff_t *off)
+{
+ struct picolcd_pending *resp;
+ u8 raw_data[4];
+ ssize_t ret = 0;
+ int len_off, err = -EIO;
+
+ while (s > 0) {
+ err = -EIO;
+ len_off = _picolcd_flash_setaddr(data, raw_data, *off);
+ raw_data[len_off] = s > 32 ? 32 : s;
+ resp = picolcd_send_and_wait(data->hdev, report_id, raw_data, len_off+1);
+ if (!resp || !resp->in_report)
+ goto skip;
+ if (resp->in_report->id == REPORT_MEMORY ||
+ resp->in_report->id == REPORT_BL_READ_MEMORY) {
+ if (memcmp(raw_data, resp->raw_data, len_off+1) != 0)
+ goto skip;
+ if (copy_to_user(u+ret, resp->raw_data+len_off+1, raw_data[len_off])) {
+ err = -EFAULT;
+ goto skip;
+ }
+ *off += raw_data[len_off];
+ s -= raw_data[len_off];
+ ret += raw_data[len_off];
+ err = 0;
+ }
+skip:
+ kfree(resp);
+ if (err)
+ return ret > 0 ? ret : err;
+ }
+ return ret;
+}
+
+static ssize_t picolcd_debug_flash_read(struct file *f, char __user *u,
+ size_t s, loff_t *off)
+{
+ struct picolcd_data *data = f->private_data;
+
+ if (s == 0)
+ return -EINVAL;
+ if (*off > 0x05fff)
+ return 0;
+ if (*off + s > 0x05fff)
+ s = 0x06000 - *off;
+
+ if (data->status & PICOLCD_BOOTLOADER)
+ return _picolcd_flash_read(data, REPORT_BL_READ_MEMORY, u, s, off);
+ else
+ return _picolcd_flash_read(data, REPORT_READ_MEMORY, u, s, off);
+}
+
+/* erase block aligned to 64bytes boundary */
+static ssize_t _picolcd_flash_erase64(struct picolcd_data *data, int report_id,
+ loff_t *off)
+{
+ struct picolcd_pending *resp;
+ u8 raw_data[3];
+ int len_off;
+ ssize_t ret = -EIO;
+
+ if (*off & 0x3f)
+ return -EINVAL;
+
+ len_off = _picolcd_flash_setaddr(data, raw_data, *off);
+ resp = picolcd_send_and_wait(data->hdev, report_id, raw_data, len_off);
+ if (!resp || !resp->in_report)
+ goto skip;
+ if (resp->in_report->id == REPORT_MEMORY ||
+ resp->in_report->id == REPORT_BL_ERASE_MEMORY) {
+ if (memcmp(raw_data, resp->raw_data, len_off) != 0)
+ goto skip;
+ ret = 0;
+ }
+skip:
+ kfree(resp);
+ return ret;
+}
+
+/* write a given size of data (bounds check to be done by caller) */
+static ssize_t _picolcd_flash_write(struct picolcd_data *data, int report_id,
+ const char __user *u, size_t s, loff_t *off)
+{
+ struct picolcd_pending *resp;
+ u8 raw_data[36];
+ ssize_t ret = 0;
+ int len_off, err = -EIO;
+
+ while (s > 0) {
+ err = -EIO;
+ len_off = _picolcd_flash_setaddr(data, raw_data, *off);
+ raw_data[len_off] = s > 32 ? 32 : s;
+ if (copy_from_user(raw_data+len_off+1, u, raw_data[len_off])) {
+ err = -EFAULT;
+ break;
+ }
+ resp = picolcd_send_and_wait(data->hdev, report_id, raw_data,
+ len_off+1+raw_data[len_off]);
+ if (!resp || !resp->in_report)
+ goto skip;
+ if (resp->in_report->id == REPORT_MEMORY ||
+ resp->in_report->id == REPORT_BL_WRITE_MEMORY) {
+ if (memcmp(raw_data, resp->raw_data, len_off+1+raw_data[len_off]) != 0)
+ goto skip;
+ *off += raw_data[len_off];
+ s -= raw_data[len_off];
+ ret += raw_data[len_off];
+ err = 0;
+ }
+skip:
+ kfree(resp);
+ if (err)
+ break;
+ }
+ return ret > 0 ? ret : err;
+}
+
+static ssize_t picolcd_debug_flash_write(struct file *f, const char __user *u,
+ size_t s, loff_t *off)
+{
+ struct picolcd_data *data = f->private_data;
+ ssize_t err, ret = 0;
+ int report_erase, report_write;
+
+ if (s == 0)
+ return -EINVAL;
+ if (*off > 0x5fff)
+ return -ENOSPC;
+ if (s & 0x3f)
+ return -EINVAL;
+ if (*off & 0x3f)
+ return -EINVAL;
+
+ if (data->status & PICOLCD_BOOTLOADER) {
+ report_erase = REPORT_BL_ERASE_MEMORY;
+ report_write = REPORT_BL_WRITE_MEMORY;
+ } else {
+ report_erase = REPORT_ERASE_MEMORY;
+ report_write = REPORT_WRITE_MEMORY;
+ }
+ mutex_lock(&data->mutex_flash);
+ while (s > 0) {
+ err = _picolcd_flash_erase64(data, report_erase, off);
+ if (err)
+ break;
+ err = _picolcd_flash_write(data, report_write, u, 64, off);
+ if (err < 0)
+ break;
+ ret += err;
+ *off += err;
+ s -= err;
+ if (err != 64)
+ break;
+ }
+ mutex_unlock(&data->mutex_flash);
+ return ret > 0 ? ret : err;
+}
+
+/*
+ * Notes:
+ * - concurrent writing is prevented by mutex and all writes must be
+ * n*64 bytes and 64-byte aligned, each write being preceded by an
+ * ERASE which erases a 64byte block.
+ * If less than requested was written or an error is returned for an
+ * otherwise correct write request the next 64-byte block which should
+ * have been written is in undefined state (mostly: original, erased,
+ * (half-)written with write error)
+ * - reading can happen without special restriction
+ */
+static const struct file_operations picolcd_debug_flash_fops = {
+ .owner = THIS_MODULE,
+ .open = simple_open,
+ .read = picolcd_debug_flash_read,
+ .write = picolcd_debug_flash_write,
+ .llseek = generic_file_llseek,
+};
+
+
+/*
+ * Helper code for HID report level dumping/debugging
+ */
+static const char *error_codes[] = {
+ "success", "parameter missing", "data_missing", "block readonly",
+ "block not erasable", "block too big", "section overflow",
+ "invalid command length", "invalid data length",
+};
+
+static void dump_buff_as_hex(char *dst, size_t dst_sz, const u8 *data,
+ const size_t data_len)
+{
+ int i, j;
+ for (i = j = 0; i < data_len && j + 3 < dst_sz; i++) {
+ dst[j++] = hex_asc[(data[i] >> 4) & 0x0f];
+ dst[j++] = hex_asc[data[i] & 0x0f];
+ dst[j++] = ' ';
+ }
+ if (j < dst_sz) {
+ dst[j--] = '\0';
+ dst[j] = '\n';
+ } else
+ dst[j] = '\0';
+}
+
+void picolcd_debug_out_report(struct picolcd_data *data,
+ struct hid_device *hdev, struct hid_report *report)
+{
+ u8 raw_data[70];
+ int raw_size = (report->size >> 3) + 1;
+ char *buff;
+#define BUFF_SZ 256
+
+ /* Avoid unnecessary overhead if debugfs is disabled */
+ if (!hdev->debug_events)
+ return;
+
+ buff = kmalloc(BUFF_SZ, GFP_ATOMIC);
+ if (!buff)
+ return;
+
+ snprintf(buff, BUFF_SZ, "\nout report %d (size %d) = ",
+ report->id, raw_size);
+ hid_debug_event(hdev, buff);
+ if (raw_size + 5 > sizeof(raw_data)) {
+ kfree(buff);
+ hid_debug_event(hdev, " TOO BIG\n");
+ return;
+ } else {
+ raw_data[0] = report->id;
+ hid_output_report(report, raw_data);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data, raw_size);
+ hid_debug_event(hdev, buff);
+ }
+
+ switch (report->id) {
+ case REPORT_LED_STATE:
+ /* 1 data byte with GPO state */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_LED_STATE", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tGPO state: 0x%02x\n", raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_BRIGHTNESS:
+ /* 1 data byte with brightness */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_BRIGHTNESS", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tBrightness: 0x%02x\n", raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_CONTRAST:
+ /* 1 data byte with contrast */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_CONTRAST", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tContrast: 0x%02x\n", raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_RESET:
+ /* 2 data bytes with reset duration in ms */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_RESET", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tDuration: 0x%02x%02x (%dms)\n",
+ raw_data[2], raw_data[1], raw_data[2] << 8 | raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_LCD_CMD:
+ /* 63 data bytes with LCD commands */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_LCD_CMD", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ /* TODO: format decoding */
+ break;
+ case REPORT_LCD_DATA:
+ /* 63 data bytes with LCD data */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_LCD_CMD", report->id, raw_size-1);
+ /* TODO: format decoding */
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_LCD_CMD_DATA:
+ /* 63 data bytes with LCD commands and data */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_LCD_CMD", report->id, raw_size-1);
+ /* TODO: format decoding */
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_EE_READ:
+ /* 3 data bytes with read area description */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_EE_READ", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_EE_WRITE:
+ /* 3+1..20 data bytes with write area description */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_EE_WRITE", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[3] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ } else if (raw_data[3] + 4 <= raw_size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ }
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_ERASE_MEMORY:
+ case REPORT_BL_ERASE_MEMORY:
+ /* 3 data bytes with pointer inside erase block */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_ERASE_MEMORY", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ switch (data->addr_sz) {
+ case 2:
+ snprintf(buff, BUFF_SZ, "\tAddress inside 64 byte block: 0x%02x%02x\n",
+ raw_data[2], raw_data[1]);
+ break;
+ case 3:
+ snprintf(buff, BUFF_SZ, "\tAddress inside 64 byte block: 0x%02x%02x%02x\n",
+ raw_data[3], raw_data[2], raw_data[1]);
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "\tNot supported\n");
+ }
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_READ_MEMORY:
+ case REPORT_BL_READ_MEMORY:
+ /* 4 data bytes with read area description */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_READ_MEMORY", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ switch (data->addr_sz) {
+ case 2:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ break;
+ case 3:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n",
+ raw_data[3], raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]);
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "\tNot supported\n");
+ }
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_WRITE_MEMORY:
+ case REPORT_BL_WRITE_MEMORY:
+ /* 4+1..32 data bytes with write adrea description */
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_WRITE_MEMORY", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ switch (data->addr_sz) {
+ case 2:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[3] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ } else if (raw_data[3] + 4 <= raw_size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ }
+ break;
+ case 3:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n",
+ raw_data[3], raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[4] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ } else if (raw_data[4] + 5 <= raw_size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+5, raw_data[4]);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ }
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "\tNot supported\n");
+ }
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_SPLASH_RESTART:
+ /* TODO */
+ break;
+ case REPORT_EXIT_KEYBOARD:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_EXIT_KEYBOARD", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tRestart delay: %dms (0x%02x%02x)\n",
+ raw_data[1] | (raw_data[2] << 8),
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_VERSION:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_VERSION", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_DEVID:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_DEVID", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_SPLASH_SIZE:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_SPLASH_SIZE", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_HOOK_VERSION:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_HOOK_VERSION", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_EXIT_FLASHER:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "REPORT_VERSION", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tRestart delay: %dms (0x%02x%02x)\n",
+ raw_data[1] | (raw_data[2] << 8),
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "out report %s (%d, size=%d)\n",
+ "<unknown>", report->id, raw_size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ }
+ wake_up_interruptible(&hdev->debug_wait);
+ kfree(buff);
+}
+
+void picolcd_debug_raw_event(struct picolcd_data *data,
+ struct hid_device *hdev, struct hid_report *report,
+ u8 *raw_data, int size)
+{
+ char *buff;
+
+#define BUFF_SZ 256
+ /* Avoid unnecessary overhead if debugfs is disabled */
+ if (!hdev->debug_events)
+ return;
+
+ buff = kmalloc(BUFF_SZ, GFP_ATOMIC);
+ if (!buff)
+ return;
+
+ switch (report->id) {
+ case REPORT_ERROR_CODE:
+ /* 2 data bytes with affected report and error code */
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_ERROR_CODE", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ if (raw_data[2] < ARRAY_SIZE(error_codes))
+ snprintf(buff, BUFF_SZ, "\tError code 0x%02x (%s) in reply to report 0x%02x\n",
+ raw_data[2], error_codes[raw_data[2]], raw_data[1]);
+ else
+ snprintf(buff, BUFF_SZ, "\tError code 0x%02x in reply to report 0x%02x\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_KEY_STATE:
+ /* 2 data bytes with key state */
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_KEY_STATE", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ if (raw_data[1] == 0)
+ snprintf(buff, BUFF_SZ, "\tNo key pressed\n");
+ else if (raw_data[2] == 0)
+ snprintf(buff, BUFF_SZ, "\tOne key pressed: 0x%02x (%d)\n",
+ raw_data[1], raw_data[1]);
+ else
+ snprintf(buff, BUFF_SZ, "\tTwo keys pressed: 0x%02x (%d), 0x%02x (%d)\n",
+ raw_data[1], raw_data[1], raw_data[2], raw_data[2]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_IR_DATA:
+ /* Up to 20 byes of IR scancode data */
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_IR_DATA", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ if (raw_data[1] == 0) {
+ snprintf(buff, BUFF_SZ, "\tUnexpectedly 0 data length\n");
+ hid_debug_event(hdev, buff);
+ } else if (raw_data[1] + 1 <= size) {
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n\tIR Data: ",
+ raw_data[1]-1);
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+2, raw_data[1]-1);
+ hid_debug_event(hdev, buff);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tOverflowing data length: %d\n",
+ raw_data[1]-1);
+ hid_debug_event(hdev, buff);
+ }
+ break;
+ case REPORT_EE_DATA:
+ /* Data buffer in response to REPORT_EE_READ or REPORT_EE_WRITE */
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_EE_DATA", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[3] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ hid_debug_event(hdev, buff);
+ } else if (raw_data[3] + 4 <= size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+ hid_debug_event(hdev, buff);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ hid_debug_event(hdev, buff);
+ }
+ break;
+ case REPORT_MEMORY:
+ /* Data buffer in response to REPORT_READ_MEMORY or REPORT_WRTIE_MEMORY */
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_MEMORY", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ switch (data->addr_sz) {
+ case 2:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[3]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[3] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ } else if (raw_data[3] + 4 <= size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+4, raw_data[3]);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ }
+ break;
+ case 3:
+ snprintf(buff, BUFF_SZ, "\tData address: 0x%02x%02x%02x\n",
+ raw_data[3], raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tData length: %d\n", raw_data[4]);
+ hid_debug_event(hdev, buff);
+ if (raw_data[4] == 0) {
+ snprintf(buff, BUFF_SZ, "\tNo data\n");
+ } else if (raw_data[4] + 5 <= size) {
+ snprintf(buff, BUFF_SZ, "\tData: ");
+ hid_debug_event(hdev, buff);
+ dump_buff_as_hex(buff, BUFF_SZ, raw_data+5, raw_data[4]);
+ } else {
+ snprintf(buff, BUFF_SZ, "\tData overflowed\n");
+ }
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "\tNot supported\n");
+ }
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_VERSION:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_VERSION", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tFirmware version: %d.%d\n",
+ raw_data[2], raw_data[1]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_BL_ERASE_MEMORY:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_BL_ERASE_MEMORY", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ /* TODO */
+ break;
+ case REPORT_BL_READ_MEMORY:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_BL_READ_MEMORY", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ /* TODO */
+ break;
+ case REPORT_BL_WRITE_MEMORY:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_BL_WRITE_MEMORY", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ /* TODO */
+ break;
+ case REPORT_DEVID:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_DEVID", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tSerial: 0x%02x%02x%02x%02x\n",
+ raw_data[1], raw_data[2], raw_data[3], raw_data[4]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tType: 0x%02x\n",
+ raw_data[5]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_SPLASH_SIZE:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_SPLASH_SIZE", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tTotal splash space: %d\n",
+ (raw_data[2] << 8) | raw_data[1]);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tUsed splash space: %d\n",
+ (raw_data[4] << 8) | raw_data[3]);
+ hid_debug_event(hdev, buff);
+ break;
+ case REPORT_HOOK_VERSION:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "REPORT_HOOK_VERSION", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ snprintf(buff, BUFF_SZ, "\tFirmware version: %d.%d\n",
+ raw_data[1], raw_data[2]);
+ hid_debug_event(hdev, buff);
+ break;
+ default:
+ snprintf(buff, BUFF_SZ, "report %s (%d, size=%d)\n",
+ "<unknown>", report->id, size-1);
+ hid_debug_event(hdev, buff);
+ break;
+ }
+ wake_up_interruptible(&hdev->debug_wait);
+ kfree(buff);
+}
+
+void picolcd_init_devfs(struct picolcd_data *data,
+ struct hid_report *eeprom_r, struct hid_report *eeprom_w,
+ struct hid_report *flash_r, struct hid_report *flash_w,
+ struct hid_report *reset)
+{
+ struct hid_device *hdev = data->hdev;
+
+ mutex_init(&data->mutex_flash);
+
+ /* reset */
+ if (reset)
+ data->debug_reset = debugfs_create_file("reset", 0600,
+ hdev->debug_dir, data, &picolcd_debug_reset_fops);
+
+ /* eeprom */
+ if (eeprom_r || eeprom_w)
+ data->debug_eeprom = debugfs_create_file("eeprom",
+ (eeprom_w ? S_IWUSR : 0) | (eeprom_r ? S_IRUSR : 0),
+ hdev->debug_dir, data, &picolcd_debug_eeprom_fops);
+
+ /* flash */
+ if (flash_r && flash_r->maxfield == 1 && flash_r->field[0]->report_size == 8)
+ data->addr_sz = flash_r->field[0]->report_count - 1;
+ else
+ data->addr_sz = -1;
+ if (data->addr_sz == 2 || data->addr_sz == 3) {
+ data->debug_flash = debugfs_create_file("flash",
+ (flash_w ? S_IWUSR : 0) | (flash_r ? S_IRUSR : 0),
+ hdev->debug_dir, data, &picolcd_debug_flash_fops);
+ } else if (flash_r || flash_w)
+ hid_warn(hdev, "Unexpected FLASH access reports, please submit rdesc for review\n");
+}
+
+void picolcd_exit_devfs(struct picolcd_data *data)
+{
+ struct dentry *dent;
+
+ dent = data->debug_reset;
+ data->debug_reset = NULL;
+ if (dent)
+ debugfs_remove(dent);
+ dent = data->debug_eeprom;
+ data->debug_eeprom = NULL;
+ if (dent)
+ debugfs_remove(dent);
+ dent = data->debug_flash;
+ data->debug_flash = NULL;
+ if (dent)
+ debugfs_remove(dent);
+ mutex_destroy(&data->mutex_flash);
+}
+
new file mode 100644
@@ -0,0 +1,673 @@
+/***************************************************************************
+ * Copyright (C) 2010-2012 by Bruno Prémont <bonbons@linux-vserver.org> *
+ * *
+ * Based on Logitech G13 driver (v0.4) *
+ * Copyright (C) 2009 by Rick L. Vinyard, Jr. <rvinyard@cs.nmsu.edu> *
+ * *
+ * This program is free software: you can redistribute it and/or modify *
+ * it under the terms of the GNU General Public License as published by *
+ * the Free Software Foundation, version 2 of the License. *
+ * *
+ * This driver is distributed in the hope that it will be useful, but *
+ * WITHOUT ANY WARRANTY; without even the implied warranty of *
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU *
+ * General Public License for more details. *
+ * *
+ * You should have received a copy of the GNU General Public License *
+ * along with this software. If not see <http://www.gnu.org/licenses/>. *
+ ***************************************************************************/
+
+#include <linux/hid.h>
+#include "usbhid/usbhid.h"
+#include <linux/usb.h>
+
+#include <linux/fb.h>
+#include <linux/module.h>
+
+#include "hid-picolcd.h"
+
+/* Framebuffer
+ *
+ * The PicoLCD use a Topway LCD module of 256x64 pixel
+ * This display area is tiled over 4 controllers with 8 tiles
+ * each. Each tile has 8x64 pixel, each data byte representing
+ * a 1-bit wide vertical line of the tile.
+ *
+ * The display can be updated at a tile granularity.
+ *
+ * Chip 1 Chip 2 Chip 3 Chip 4
+ * +----------------+----------------+----------------+----------------+
+ * | Tile 1 | Tile 1 | Tile 1 | Tile 1 |
+ * +----------------+----------------+----------------+----------------+
+ * | Tile 2 | Tile 2 | Tile 2 | Tile 2 |
+ * +----------------+----------------+----------------+----------------+
+ * ...
+ * +----------------+----------------+----------------+----------------+
+ * | Tile 8 | Tile 8 | Tile 8 | Tile 8 |
+ * +----------------+----------------+----------------+----------------+
+ */
+#define PICOLCDFB_NAME "picolcdfb"
+#define PICOLCDFB_WIDTH (256)
+#define PICOLCDFB_HEIGHT (64)
+#define PICOLCDFB_SIZE (PICOLCDFB_WIDTH * PICOLCDFB_HEIGHT / 8)
+
+#define PICOLCDFB_UPDATE_RATE_LIMIT 10
+#define PICOLCDFB_UPDATE_RATE_DEFAULT 2
+
+/* Framebuffer visual structures */
+static const struct fb_fix_screeninfo picolcdfb_fix = {
+ .id = PICOLCDFB_NAME,
+ .type = FB_TYPE_PACKED_PIXELS,
+ .visual = FB_VISUAL_MONO01,
+ .xpanstep = 0,
+ .ypanstep = 0,
+ .ywrapstep = 0,
+ .line_length = PICOLCDFB_WIDTH / 8,
+ .accel = FB_ACCEL_NONE,
+};
+
+static const struct fb_var_screeninfo picolcdfb_var = {
+ .xres = PICOLCDFB_WIDTH,
+ .yres = PICOLCDFB_HEIGHT,
+ .xres_virtual = PICOLCDFB_WIDTH,
+ .yres_virtual = PICOLCDFB_HEIGHT,
+ .width = 103,
+ .height = 26,
+ .bits_per_pixel = 1,
+ .grayscale = 1,
+ .red = {
+ .offset = 0,
+ .length = 1,
+ .msb_right = 0,
+ },
+ .green = {
+ .offset = 0,
+ .length = 1,
+ .msb_right = 0,
+ },
+ .blue = {
+ .offset = 0,
+ .length = 1,
+ .msb_right = 0,
+ },
+ .transp = {
+ .offset = 0,
+ .length = 0,
+ .msb_right = 0,
+ },
+};
+
+/* Send a given tile to PicoLCD */
+static int picolcd_fb_send_tile(struct hid_device *hdev, int chip, int tile)
+{
+ struct picolcd_data *data = hid_get_drvdata(hdev);
+ struct hid_report *report1 = picolcd_out_report(REPORT_LCD_CMD_DATA, hdev);
+ struct hid_report *report2 = picolcd_out_report(REPORT_LCD_DATA, hdev);
+ unsigned long flags;
+ u8 *tdata;
+ int i;
+
+ if (!report1 || report1->maxfield != 1 || !report2 || report2->maxfield != 1)
+ return -ENODEV;
+
+ spin_lock_irqsave(&data->lock, flags);
+ hid_set_field(report1->field[0], 0, chip << 2);
+ hid_set_field(report1->field[0], 1, 0x02);
+ hid_set_field(report1->field[0], 2, 0x00);
+ hid_set_field(report1->field[0], 3, 0x00);
+ hid_set_field(report1->field[0], 4, 0xb8 | tile);
+ hid_set_field(report1->field[0], 5, 0x00);
+ hid_set_field(report1->field[0], 6, 0x00);
+ hid_set_field(report1->field[0], 7, 0x40);
+ hid_set_field(report1->field[0], 8, 0x00);
+ hid_set_field(report1->field[0], 9, 0x00);
+ hid_set_field(report1->field[0], 10, 32);
+
+ hid_set_field(report2->field[0], 0, (chip << 2) | 0x01);
+ hid_set_field(report2->field[0], 1, 0x00);
+ hid_set_field(report2->field[0], 2, 0x00);
+ hid_set_field(report2->field[0], 3, 32);
+
+ tdata = data->fb_vbitmap + (tile * 4 + chip) * 64;
+ for (i = 0; i < 64; i++)
+ if (i < 32)
+ hid_set_field(report1->field[0], 11 + i, tdata[i]);
+ else
+ hid_set_field(report2->field[0], 4 + i - 32, tdata[i]);
+
+ usbhid_submit_report(data->hdev, report1, USB_DIR_OUT);
+ usbhid_submit_report(data->hdev, report2, USB_DIR_OUT);
+ spin_unlock_irqrestore(&data->lock, flags);
+ return 0;
+}
+
+/* Translate a single tile*/
+static int picolcd_fb_update_tile(u8 *vbitmap, const u8 *bitmap, int bpp,
+ int chip, int tile)
+{
+ int i, b, changed = 0;
+ u8 tdata[64];
+ u8 *vdata = vbitmap + (tile * 4 + chip) * 64;
+
+ if (bpp == 1) {
+ for (b = 7; b >= 0; b--) {
+ const u8 *bdata = bitmap + tile * 256 + chip * 8 + b * 32;
+ for (i = 0; i < 64; i++) {
+ tdata[i] <<= 1;
+ tdata[i] |= (bdata[i/8] >> (i % 8)) & 0x01;
+ }
+ }
+ } else if (bpp == 8) {
+ for (b = 7; b >= 0; b--) {
+ const u8 *bdata = bitmap + (tile * 256 + chip * 8 + b * 32) * 8;
+ for (i = 0; i < 64; i++) {
+ tdata[i] <<= 1;
+ tdata[i] |= (bdata[i] & 0x80) ? 0x01 : 0x00;
+ }
+ }
+ } else {
+ /* Oops, we should never get here! */
+ WARN_ON(1);
+ return 0;
+ }
+
+ for (i = 0; i < 64; i++)
+ if (tdata[i] != vdata[i]) {
+ changed = 1;
+ vdata[i] = tdata[i];
+ }
+ return changed;
+}
+
+void picolcd_fb_refresh(struct picolcd_data *data)
+{
+ if (data->fb_info)
+ schedule_delayed_work(&data->fb_info->deferred_work, 0);
+}
+
+/* Reconfigure LCD display */
+int picolcd_fb_reset(struct picolcd_data *data, int clear)
+{
+ struct hid_report *report = picolcd_out_report(REPORT_LCD_CMD, data->hdev);
+ int i, j;
+ unsigned long flags;
+ static const u8 mapcmd[8] = { 0x00, 0x02, 0x00, 0x64, 0x3f, 0x00, 0x64, 0xc0 };
+
+ if (!report || report->maxfield != 1)
+ return -ENODEV;
+
+ spin_lock_irqsave(&data->lock, flags);
+ for (i = 0; i < 4; i++) {
+ for (j = 0; j < report->field[0]->maxusage; j++)
+ if (j == 0)
+ hid_set_field(report->field[0], j, i << 2);
+ else if (j < sizeof(mapcmd))
+ hid_set_field(report->field[0], j, mapcmd[j]);
+ else
+ hid_set_field(report->field[0], j, 0);
+ usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+ }
+
+ data->status |= PICOLCD_READY_FB;
+ spin_unlock_irqrestore(&data->lock, flags);
+
+ if (data->fb_bitmap) {
+ if (clear) {
+ memset(data->fb_vbitmap, 0, PICOLCDFB_SIZE);
+ memset(data->fb_bitmap, 0, PICOLCDFB_SIZE*data->fb_bpp);
+ }
+ data->fb_force = 1;
+ }
+
+ /* schedule first output of framebuffer */
+ picolcd_fb_refresh(data);
+
+ return 0;
+}
+
+/* Update fb_vbitmap from the screen_base and send changed tiles to device */
+static void picolcd_fb_update(struct picolcd_data *data)
+{
+ int chip, tile, n;
+ unsigned long flags;
+
+ if (!data)
+ return;
+
+ spin_lock_irqsave(&data->lock, flags);
+ if (!(data->status & PICOLCD_READY_FB)) {
+ spin_unlock_irqrestore(&data->lock, flags);
+ picolcd_fb_reset(data, 0);
+ } else {
+ spin_unlock_irqrestore(&data->lock, flags);
+ }
+
+ /*
+ * Translate the framebuffer into the format needed by the PicoLCD.
+ * See display layout above.
+ * Do this one tile after the other and push those tiles that changed.
+ *
+ * Wait for our IO to complete as otherwise we might flood the queue!
+ */
+ n = 0;
+ for (chip = 0; chip < 4; chip++)
+ for (tile = 0; tile < 8; tile++)
+ if (picolcd_fb_update_tile(data->fb_vbitmap,
+ data->fb_bitmap, data->fb_bpp, chip, tile) ||
+ data->fb_force) {
+ n += 2;
+ if (!data->fb_info->par)
+ return; /* device lost! */
+ if (n >= HID_OUTPUT_FIFO_SIZE / 2) {
+ usbhid_wait_io(data->hdev);
+ n = 0;
+ }
+ picolcd_fb_send_tile(data->hdev, chip, tile);
+ }
+ data->fb_force = false;
+ if (n)
+ usbhid_wait_io(data->hdev);
+}
+
+/* Stub to call the system default and update the image on the picoLCD */
+static void picolcd_fb_fillrect(struct fb_info *info,
+ const struct fb_fillrect *rect)
+{
+ if (!info->par)
+ return;
+ sys_fillrect(info, rect);
+
+ schedule_delayed_work(&info->deferred_work, 0);
+}
+
+/* Stub to call the system default and update the image on the picoLCD */
+static void picolcd_fb_copyarea(struct fb_info *info,
+ const struct fb_copyarea *area)
+{
+ if (!info->par)
+ return;
+ sys_copyarea(info, area);
+
+ schedule_delayed_work(&info->deferred_work, 0);
+}
+
+/* Stub to call the system default and update the image on the picoLCD */
+static void picolcd_fb_imageblit(struct fb_info *info, const struct fb_image *image)
+{
+ if (!info->par)
+ return;
+ sys_imageblit(info, image);
+
+ schedule_delayed_work(&info->deferred_work, 0);
+}
+
+/*
+ * this is the slow path from userspace. they can seek and write to
+ * the fb. it's inefficient to do anything less than a full screen draw
+ */
+static ssize_t picolcd_fb_write(struct fb_info *info, const char __user *buf,
+ size_t count, loff_t *ppos)
+{
+ ssize_t ret;
+ if (!info->par)
+ return -ENODEV;
+ ret = fb_sys_write(info, buf, count, ppos);
+ if (ret >= 0)
+ schedule_delayed_work(&info->deferred_work, 0);
+ return ret;
+}
+
+static int picolcd_fb_blank(int blank, struct fb_info *info)
+{
+ if (!info->par)
+ return -ENODEV;
+ /* We let fb notification do this for us via lcd/backlight device */
+ return 0;
+}
+
+static void picolcd_fb_destroy(struct fb_info *info)
+{
+ struct picolcd_data *data = info->par;
+ u32 *ref_cnt = info->pseudo_palette;
+ int may_release;
+
+ info->par = NULL;
+ if (data)
+ data->fb_info = NULL;
+ fb_deferred_io_cleanup(info);
+
+ ref_cnt--;
+ mutex_lock(&info->lock);
+ (*ref_cnt)--;
+ may_release = !*ref_cnt;
+ mutex_unlock(&info->lock);
+ if (may_release) {
+ vfree((u8 *)info->fix.smem_start);
+ framebuffer_release(info);
+ }
+}
+
+static int picolcd_fb_check_var(struct fb_var_screeninfo *var, struct fb_info *info)
+{
+ __u32 bpp = var->bits_per_pixel;
+ __u32 activate = var->activate;
+
+ /* only allow 1/8 bit depth (8-bit is grayscale) */
+ *var = picolcdfb_var;
+ var->activate = activate;
+ if (bpp >= 8) {
+ var->bits_per_pixel = 8;
+ var->red.length = 8;
+ var->green.length = 8;
+ var->blue.length = 8;
+ } else {
+ var->bits_per_pixel = 1;
+ var->red.length = 1;
+ var->green.length = 1;
+ var->blue.length = 1;
+ }
+ return 0;
+}
+
+static int picolcd_set_par(struct fb_info *info)
+{
+ struct picolcd_data *data = info->par;
+ u8 *tmp_fb, *o_fb;
+ if (!data)
+ return -ENODEV;
+ if (info->var.bits_per_pixel == data->fb_bpp)
+ return 0;
+ /* switch between 1/8 bit depths */
+ if (info->var.bits_per_pixel != 1 && info->var.bits_per_pixel != 8)
+ return -EINVAL;
+
+ o_fb = data->fb_bitmap;
+ tmp_fb = kmalloc(PICOLCDFB_SIZE*info->var.bits_per_pixel, GFP_KERNEL);
+ if (!tmp_fb)
+ return -ENOMEM;
+
+ /* translate FB content to new bits-per-pixel */
+ if (info->var.bits_per_pixel == 1) {
+ int i, b;
+ for (i = 0; i < PICOLCDFB_SIZE; i++) {
+ u8 p = 0;
+ for (b = 0; b < 8; b++) {
+ p <<= 1;
+ p |= o_fb[i*8+b] ? 0x01 : 0x00;
+ }
+ tmp_fb[i] = p;
+ }
+ memcpy(o_fb, tmp_fb, PICOLCDFB_SIZE);
+ info->fix.visual = FB_VISUAL_MONO01;
+ info->fix.line_length = PICOLCDFB_WIDTH / 8;
+ } else {
+ int i;
+ memcpy(tmp_fb, o_fb, PICOLCDFB_SIZE);
+ for (i = 0; i < PICOLCDFB_SIZE * 8; i++)
+ o_fb[i] = tmp_fb[i/8] & (0x01 << (7 - i % 8)) ? 0xff : 0x00;
+ info->fix.visual = FB_VISUAL_DIRECTCOLOR;
+ info->fix.line_length = PICOLCDFB_WIDTH;
+ }
+
+ kfree(tmp_fb);
+ data->fb_bpp = info->var.bits_per_pixel;
+ return 0;
+}
+
+/* Do refcounting on our FB and cleanup per worker if FB is
+ * closed after unplug of our device
+ * (fb_release holds info->lock and still touches info after
+ * we return so we can't release it immediately.
+ */
+struct picolcd_fb_cleanup_item {
+ struct fb_info *info;
+ struct picolcd_fb_cleanup_item *next;
+};
+static struct picolcd_fb_cleanup_item *fb_pending;
+static DEFINE_SPINLOCK(fb_pending_lock);
+
+static void picolcd_fb_do_cleanup(struct work_struct *data)
+{
+ struct picolcd_fb_cleanup_item *item;
+ unsigned long flags;
+
+ do {
+ spin_lock_irqsave(&fb_pending_lock, flags);
+ item = fb_pending;
+ fb_pending = item ? item->next : NULL;
+ spin_unlock_irqrestore(&fb_pending_lock, flags);
+
+ if (item) {
+ u8 *fb = (u8 *)item->info->fix.smem_start;
+ /* make sure we do not race against fb core when
+ * releasing */
+ mutex_lock(&item->info->lock);
+ mutex_unlock(&item->info->lock);
+ framebuffer_release(item->info);
+ vfree(fb);
+ }
+ } while (item);
+}
+
+static DECLARE_WORK(picolcd_fb_cleanup, picolcd_fb_do_cleanup);
+
+static int picolcd_fb_open(struct fb_info *info, int u)
+{
+ u32 *ref_cnt = info->pseudo_palette;
+ ref_cnt--;
+
+ (*ref_cnt)++;
+ return 0;
+}
+
+static int picolcd_fb_release(struct fb_info *info, int u)
+{
+ u32 *ref_cnt = info->pseudo_palette;
+ ref_cnt--;
+
+ (*ref_cnt)++;
+ if (!*ref_cnt) {
+ unsigned long flags;
+ struct picolcd_fb_cleanup_item *item = (struct picolcd_fb_cleanup_item *)ref_cnt;
+ item--;
+ spin_lock_irqsave(&fb_pending_lock, flags);
+ item->next = fb_pending;
+ fb_pending = item;
+ spin_unlock_irqrestore(&fb_pending_lock, flags);
+ schedule_work(&picolcd_fb_cleanup);
+ }
+ return 0;
+}
+
+/* Note this can't be const because of struct fb_info definition */
+static struct fb_ops picolcdfb_ops = {
+ .owner = THIS_MODULE,
+ .fb_destroy = picolcd_fb_destroy,
+ .fb_open = picolcd_fb_open,
+ .fb_release = picolcd_fb_release,
+ .fb_read = fb_sys_read,
+ .fb_write = picolcd_fb_write,
+ .fb_blank = picolcd_fb_blank,
+ .fb_fillrect = picolcd_fb_fillrect,
+ .fb_copyarea = picolcd_fb_copyarea,
+ .fb_imageblit = picolcd_fb_imageblit,
+ .fb_check_var = picolcd_fb_check_var,
+ .fb_set_par = picolcd_set_par,
+};
+
+
+/* Callback from deferred IO workqueue */
+static void picolcd_fb_deferred_io(struct fb_info *info, struct list_head *pagelist)
+{
+ picolcd_fb_update(info->par);
+}
+
+static const struct fb_deferred_io picolcd_fb_defio = {
+ .delay = HZ / PICOLCDFB_UPDATE_RATE_DEFAULT,
+ .deferred_io = picolcd_fb_deferred_io,
+};
+
+
+/*
+ * The "fb_update_rate" sysfs attribute
+ */
+static ssize_t picolcd_fb_update_rate_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct picolcd_data *data = dev_get_drvdata(dev);
+ unsigned i, fb_update_rate = data->fb_update_rate;
+ size_t ret = 0;
+
+ for (i = 1; i <= PICOLCDFB_UPDATE_RATE_LIMIT; i++)
+ if (ret >= PAGE_SIZE)
+ break;
+ else if (i == fb_update_rate)
+ ret += snprintf(buf+ret, PAGE_SIZE-ret, "[%u] ", i);
+ else
+ ret += snprintf(buf+ret, PAGE_SIZE-ret, "%u ", i);
+ if (ret > 0)
+ buf[min(ret, (size_t)PAGE_SIZE)-1] = '\n';
+ return ret;
+}
+
+static ssize_t picolcd_fb_update_rate_store(struct device *dev,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ struct picolcd_data *data = dev_get_drvdata(dev);
+ int i;
+ unsigned u;
+
+ if (count < 1 || count > 10)
+ return -EINVAL;
+
+ i = sscanf(buf, "%u", &u);
+ if (i != 1)
+ return -EINVAL;
+
+ if (u > PICOLCDFB_UPDATE_RATE_LIMIT)
+ return -ERANGE;
+ else if (u == 0)
+ u = PICOLCDFB_UPDATE_RATE_DEFAULT;
+
+ data->fb_update_rate = u;
+ data->fb_defio.delay = HZ / data->fb_update_rate;
+ return count;
+}
+
+static DEVICE_ATTR(fb_update_rate, 0666, picolcd_fb_update_rate_show,
+ picolcd_fb_update_rate_store);
+
+/* initialize Framebuffer device */
+int picolcd_init_framebuffer(struct picolcd_data *data)
+{
+ struct device *dev = &data->hdev->dev;
+ struct fb_info *info = NULL;
+ int i, error = -ENOMEM;
+ u8 *fb_vbitmap = NULL;
+ u8 *fb_bitmap = NULL;
+ u32 *palette;
+
+ fb_bitmap = vmalloc(PICOLCDFB_SIZE*8);
+ if (fb_bitmap == NULL) {
+ dev_err(dev, "can't get a free page for framebuffer\n");
+ goto err_nomem;
+ }
+
+ fb_vbitmap = kmalloc(PICOLCDFB_SIZE, GFP_KERNEL);
+ if (fb_vbitmap == NULL) {
+ dev_err(dev, "can't alloc vbitmap image buffer\n");
+ goto err_nomem;
+ }
+
+ data->fb_update_rate = PICOLCDFB_UPDATE_RATE_DEFAULT;
+ data->fb_defio = picolcd_fb_defio;
+ /* The extra memory is:
+ * - struct picolcd_fb_cleanup_item
+ * - u32 for ref_count
+ * - 256*u32 for pseudo_palette
+ */
+ info = framebuffer_alloc(257 * sizeof(u32) + sizeof(struct picolcd_fb_cleanup_item), dev);
+ if (info == NULL) {
+ dev_err(dev, "failed to allocate a framebuffer\n");
+ goto err_nomem;
+ }
+
+ palette = info->par + sizeof(struct picolcd_fb_cleanup_item);
+ *palette = 1;
+ palette++;
+ for (i = 0; i < 256; i++)
+ palette[i] = i > 0 && i < 16 ? 0xff : 0;
+ info->pseudo_palette = palette;
+ info->fbdefio = &data->fb_defio;
+ info->screen_base = (char __force __iomem *)fb_bitmap;
+ info->fbops = &picolcdfb_ops;
+ info->var = picolcdfb_var;
+ info->fix = picolcdfb_fix;
+ info->fix.smem_len = PICOLCDFB_SIZE*8;
+ info->fix.smem_start = (unsigned long)fb_bitmap;
+ info->par = data;
+ info->flags = FBINFO_FLAG_DEFAULT;
+
+ data->fb_vbitmap = fb_vbitmap;
+ data->fb_bitmap = fb_bitmap;
+ data->fb_bpp = picolcdfb_var.bits_per_pixel;
+ error = picolcd_fb_reset(data, 1);
+ if (error) {
+ dev_err(dev, "failed to configure display\n");
+ goto err_cleanup;
+ }
+ error = device_create_file(dev, &dev_attr_fb_update_rate);
+ if (error) {
+ dev_err(dev, "failed to create sysfs attributes\n");
+ goto err_cleanup;
+ }
+ fb_deferred_io_init(info);
+ data->fb_info = info;
+ error = register_framebuffer(info);
+ if (error) {
+ dev_err(dev, "failed to register framebuffer\n");
+ goto err_sysfs;
+ }
+ /* schedule first output of framebuffer */
+ data->fb_force = 1;
+ schedule_delayed_work(&info->deferred_work, 0);
+ return 0;
+
+err_sysfs:
+ fb_deferred_io_cleanup(info);
+ device_remove_file(dev, &dev_attr_fb_update_rate);
+err_cleanup:
+ data->fb_vbitmap = NULL;
+ data->fb_bitmap = NULL;
+ data->fb_bpp = 0;
+ data->fb_info = NULL;
+
+err_nomem:
+ framebuffer_release(info);
+ vfree(fb_bitmap);
+ kfree(fb_vbitmap);
+ return error;
+}
+
+void picolcd_exit_framebuffer(struct picolcd_data *data)
+{
+ struct fb_info *info = data->fb_info;
+ u8 *fb_vbitmap = data->fb_vbitmap;
+
+ if (!info)
+ return;
+
+ device_remove_file(&data->hdev->dev, &dev_attr_fb_update_rate);
+ unregister_framebuffer(info);
+ data->fb_vbitmap = NULL;
+ data->fb_bitmap = NULL;
+ data->fb_bpp = 0;
+ data->fb_info = NULL;
+ kfree(fb_vbitmap);
+}
+
+void picolcd_fb_unload()
+{
+ flush_work_sync(&picolcd_fb_cleanup);
+ WARN_ON(fb_pending);
+}
new file mode 100644
@@ -0,0 +1,106 @@
+/***************************************************************************
+ * Copyright (C) 2010-2012 by Bruno Prémont <bonbons@linux-vserver.org> *
+ * *
+ * Based on Logitech G13 driver (v0.4) *
+ * Copyright (C) 2009 by Rick L. Vinyard, Jr. <rvinyard@cs.nmsu.edu> *
+ * *
+ * This program is free software: you can redistribute it and/or modify *
+ * it under the terms of the GNU General Public License as published by *
+ * the Free Software Foundation, version 2 of the License. *
+ * *
+ * This driver is distributed in the hope that it will be useful, but *
+ * WITHOUT ANY WARRANTY; without even the implied warranty of *
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU *
+ * General Public License for more details. *
+ * *
+ * You should have received a copy of the GNU General Public License *
+ * along with this software. If not see <http://www.gnu.org/licenses/>. *
+ ***************************************************************************/
+
+#include <linux/hid.h>
+#include "usbhid/usbhid.h"
+#include <linux/usb.h>
+
+#include <linux/fb.h>
+#include <linux/lcd.h>
+
+#include "hid-picolcd.h"
+
+/*
+ * lcd class device
+ */
+static int picolcd_get_contrast(struct lcd_device *ldev)
+{
+ struct picolcd_data *data = lcd_get_data(ldev);
+ return data->lcd_contrast;
+}
+
+static int picolcd_set_contrast(struct lcd_device *ldev, int contrast)
+{
+ struct picolcd_data *data = lcd_get_data(ldev);
+ struct hid_report *report = picolcd_out_report(REPORT_CONTRAST, data->hdev);
+ unsigned long flags;
+
+ if (!report || report->maxfield != 1 || report->field[0]->report_count != 1)
+ return -ENODEV;
+
+ data->lcd_contrast = contrast & 0x0ff;
+ spin_lock_irqsave(&data->lock, flags);
+ hid_set_field(report->field[0], 0, data->lcd_contrast);
+ usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+ spin_unlock_irqrestore(&data->lock, flags);
+ return 0;
+}
+
+static int picolcd_check_lcd_fb(struct lcd_device *ldev, struct fb_info *fb)
+{
+ return fb && fb == picolcd_fbinfo((struct picolcd_data *)lcd_get_data(ldev));
+}
+
+static struct lcd_ops picolcd_lcdops = {
+ .get_contrast = picolcd_get_contrast,
+ .set_contrast = picolcd_set_contrast,
+ .check_fb = picolcd_check_lcd_fb,
+};
+
+int picolcd_init_lcd(struct picolcd_data *data, struct hid_report *report)
+{
+ struct device *dev = &data->hdev->dev;
+ struct lcd_device *ldev;
+
+ if (!report)
+ return -ENODEV;
+ if (report->maxfield != 1 || report->field[0]->report_count != 1 ||
+ report->field[0]->report_size != 8) {
+ dev_err(dev, "unsupported CONTRAST report");
+ return -EINVAL;
+ }
+
+ ldev = lcd_device_register(dev_name(dev), dev, data, &picolcd_lcdops);
+ if (IS_ERR(ldev)) {
+ dev_err(dev, "failed to register LCD\n");
+ return PTR_ERR(ldev);
+ }
+ ldev->props.max_contrast = 0x0ff;
+ data->lcd_contrast = 0xe5;
+ data->lcd = ldev;
+ picolcd_set_contrast(ldev, 0xe5);
+ return 0;
+}
+
+void picolcd_exit_lcd(struct picolcd_data *data)
+{
+ struct lcd_device *ldev = data->lcd;
+
+ data->lcd = NULL;
+ if (ldev)
+ lcd_device_unregister(ldev);
+}
+
+int picolcd_resume_lcd(struct picolcd_data *data)
+{
+ if (!data->lcd)
+ return 0;
+ return picolcd_set_contrast(data->lcd, data->lcd_contrast);
+}
+
new file mode 100644
@@ -0,0 +1,172 @@
+/***************************************************************************
+ * Copyright (C) 2010-2012 by Bruno Prémont <bonbons@linux-vserver.org> *
+ * *
+ * Based on Logitech G13 driver (v0.4) *
+ * Copyright (C) 2009 by Rick L. Vinyard, Jr. <rvinyard@cs.nmsu.edu> *
+ * *
+ * This program is free software: you can redistribute it and/or modify *
+ * it under the terms of the GNU General Public License as published by *
+ * the Free Software Foundation, version 2 of the License. *
+ * *
+ * This driver is distributed in the hope that it will be useful, but *
+ * WITHOUT ANY WARRANTY; without even the implied warranty of *
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU *
+ * General Public License for more details. *
+ * *
+ * You should have received a copy of the GNU General Public License *
+ * along with this software. If not see <http://www.gnu.org/licenses/>. *
+ ***************************************************************************/
+
+#include <linux/hid.h>
+#include <linux/hid-debug.h>
+#include <linux/input.h>
+#include "hid-ids.h"
+#include "usbhid/usbhid.h"
+#include <linux/usb.h>
+
+#include <linux/fb.h>
+#include <linux/vmalloc.h>
+#include <linux/backlight.h>
+#include <linux/lcd.h>
+
+#include <linux/leds.h>
+
+#include <linux/seq_file.h>
+#include <linux/debugfs.h>
+
+#include <linux/completion.h>
+#include <linux/uaccess.h>
+#include <linux/module.h>
+
+#include "hid-picolcd.h"
+
+
+void picolcd_leds_set(struct picolcd_data *data)
+{
+ struct hid_report *report;
+ unsigned long flags;
+
+ if (!data->led[0])
+ return;
+ report = picolcd_out_report(REPORT_LED_STATE, data->hdev);
+ if (!report || report->maxfield != 1 || report->field[0]->report_count != 1)
+ return;
+
+ spin_lock_irqsave(&data->lock, flags);
+ hid_set_field(report->field[0], 0, data->led_state);
+ usbhid_submit_report(data->hdev, report, USB_DIR_OUT);
+ spin_unlock_irqrestore(&data->lock, flags);
+}
+
+static void picolcd_led_set_brightness(struct led_classdev *led_cdev,
+ enum led_brightness value)
+{
+ struct device *dev;
+ struct hid_device *hdev;
+ struct picolcd_data *data;
+ int i, state = 0;
+
+ dev = led_cdev->dev->parent;
+ hdev = container_of(dev, struct hid_device, dev);
+ data = hid_get_drvdata(hdev);
+ for (i = 0; i < 8; i++) {
+ if (led_cdev != data->led[i])
+ continue;
+ state = (data->led_state >> i) & 1;
+ if (value == LED_OFF && state) {
+ data->led_state &= ~(1 << i);
+ picolcd_leds_set(data);
+ } else if (value != LED_OFF && !state) {
+ data->led_state |= 1 << i;
+ picolcd_leds_set(data);
+ }
+ break;
+ }
+}
+
+static enum led_brightness picolcd_led_get_brightness(struct led_classdev *led_cdev)
+{
+ struct device *dev;
+ struct hid_device *hdev;
+ struct picolcd_data *data;
+ int i, value = 0;
+
+ dev = led_cdev->dev->parent;
+ hdev = container_of(dev, struct hid_device, dev);
+ data = hid_get_drvdata(hdev);
+ for (i = 0; i < 8; i++)
+ if (led_cdev == data->led[i]) {
+ value = (data->led_state >> i) & 1;
+ break;
+ }
+ return value ? LED_FULL : LED_OFF;
+}
+
+int picolcd_init_leds(struct picolcd_data *data, struct hid_report *report)
+{
+ struct device *dev = &data->hdev->dev;
+ struct led_classdev *led;
+ size_t name_sz = strlen(dev_name(dev)) + 8;
+ char *name;
+ int i, ret = 0;
+
+ if (!report)
+ return -ENODEV;
+ if (report->maxfield != 1 || report->field[0]->report_count != 1 ||
+ report->field[0]->report_size != 8) {
+ dev_err(dev, "unsupported LED_STATE report");
+ return -EINVAL;
+ }
+
+ for (i = 0; i < 8; i++) {
+ led = kzalloc(sizeof(struct led_classdev)+name_sz, GFP_KERNEL);
+ if (!led) {
+ dev_err(dev, "can't allocate memory for LED %d\n", i);
+ ret = -ENOMEM;
+ goto err;
+ }
+ name = (void *)(&led[1]);
+ snprintf(name, name_sz, "%s::GPO%d", dev_name(dev), i);
+ led->name = name;
+ led->brightness = 0;
+ led->max_brightness = 1;
+ led->brightness_get = picolcd_led_get_brightness;
+ led->brightness_set = picolcd_led_set_brightness;
+
+ data->led[i] = led;
+ ret = led_classdev_register(dev, data->led[i]);
+ if (ret) {
+ data->led[i] = NULL;
+ kfree(led);
+ dev_err(dev, "can't register LED %d\n", i);
+ goto err;
+ }
+ }
+ return 0;
+err:
+ for (i = 0; i < 8; i++)
+ if (data->led[i]) {
+ led = data->led[i];
+ data->led[i] = NULL;
+ led_classdev_unregister(led);
+ kfree(led);
+ }
+ return ret;
+}
+
+void picolcd_exit_leds(struct picolcd_data *data)
+{
+ struct led_classdev *led;
+ int i;
+
+ for (i = 0; i < 8; i++) {
+ led = data->led[i];
+ data->led[i] = NULL;
+ if (!led)
+ continue;
+ led_classdev_unregister(led);
+ kfree(led);
+ }
+}
+
+
--
1.7.8.6
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
In order to make code maintenance easier, split the vairous functions into individial files (this removes a bunch of #ifdefs). Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org> --- WARNING: this is a mangled resend of this patch (removed the payload of hunk that deletes drivers/hid/hid-picolcd.c to halve the patch's size) as resulting mail is otherwise too big for vger (unless bless by list owner)... If needed, please ask for off-list resending of this patch, though dropping the first (and mangled) hunk before attempting to apply and then manually removing the file should do. drivers/hid/hid-picolcd.c | 2752 ----------------------------------- drivers/hid/Kconfig | 8 + drivers/hid/Makefile | 20 + drivers/hid/hid-picolcd.h | 306 ++++ drivers/hid/hid-picolcd_backlight.c | 121 ++ drivers/hid/hid-picolcd_cir.c | 61 + drivers/hid/hid-picolcd_core.c | 704 +++++++++ drivers/hid/hid-picolcd_debugfs.c | 898 ++++++++++++ drivers/hid/hid-picolcd_fb.c | 673 +++++++++ drivers/hid/hid-picolcd_lcd.c | 106 ++ drivers/hid/hid-picolcd_leds.c | 172 +++ 11 files changed, 3069 insertions(+), 2752 deletions(-) delete mode 100644 drivers/hid/hid-picolcd.c create mode 100644 drivers/hid/hid-picolcd.h create mode 100644 drivers/hid/hid-picolcd_backlight.c create mode 100644 drivers/hid/hid-picolcd_cir.c create mode 100644 drivers/hid/hid-picolcd_core.c create mode 100644 drivers/hid/hid-picolcd_debugfs.c create mode 100644 drivers/hid/hid-picolcd_fb.c create mode 100644 drivers/hid/hid-picolcd_lcd.c create mode 100644 drivers/hid/hid-picolcd_leds.c