@@ -246,7 +246,6 @@ config INPUT_MC13783_PWRBUTTON
config INPUT_MMA8450
tristate "MMA8450 - Freescale's 3-Axis, 8/12-bit Digital Accelerometer"
depends on I2C
- select INPUT_POLLDEV
help
Say Y here if you want to support Freescale's MMA8450 Accelerometer
through I2C interface.
@@ -10,7 +10,7 @@
#include <linux/slab.h>
#include <linux/delay.h>
#include <linux/i2c.h>
-#include <linux/input-polldev.h>
+#include <linux/input.h>
#include <linux/of_device.h>
#define MMA8450_DRV_NAME "mma8450"
@@ -39,15 +39,8 @@
#define MMA8450_CTRL_REG1 0x38
#define MMA8450_CTRL_REG2 0x39
-/* mma8450 status */
-struct mma8450 {
- struct i2c_client *client;
- struct input_polled_dev *idev;
-};
-
-static int mma8450_read(struct mma8450 *m, unsigned off)
+static int mma8450_read(struct i2c_client *c, unsigned int off)
{
- struct i2c_client *c = m->client;
int ret;
ret = i2c_smbus_read_byte_data(c, off);
@@ -59,9 +52,8 @@ static int mma8450_read(struct mma8450 *m, unsigned off)
return ret;
}
-static int mma8450_write(struct mma8450 *m, unsigned off, u8 v)
+static int mma8450_write(struct i2c_client *c, unsigned int off, u8 v)
{
- struct i2c_client *c = m->client;
int error;
error = i2c_smbus_write_byte_data(c, off, v);
@@ -75,10 +67,9 @@ static int mma8450_write(struct mma8450 *m, unsigned off, u8 v)
return 0;
}
-static int mma8450_read_block(struct mma8450 *m, unsigned off,
+static int mma8450_read_block(struct i2c_client *c, unsigned int off,
u8 *buf, size_t size)
{
- struct i2c_client *c = m->client;
int err;
err = i2c_smbus_read_i2c_block_data(c, off, size, buf);
@@ -92,21 +83,21 @@ static int mma8450_read_block(struct mma8450 *m, unsigned off,
return 0;
}
-static void mma8450_poll(struct input_polled_dev *dev)
+static void mma8450_poll(struct input_dev *input)
{
- struct mma8450 *m = dev->private;
+ struct i2c_client *c = input_get_drvdata(input);
int x, y, z;
int ret;
u8 buf[6];
- ret = mma8450_read(m, MMA8450_STATUS);
+ ret = mma8450_read(c, MMA8450_STATUS);
if (ret < 0)
return;
if (!(ret & MMA8450_STATUS_ZXYDR))
return;
- ret = mma8450_read_block(m, MMA8450_OUT_X_LSB, buf, sizeof(buf));
+ ret = mma8450_read_block(c, MMA8450_OUT_X_LSB, buf, sizeof(buf));
if (ret < 0)
return;
@@ -114,41 +105,42 @@ static void mma8450_poll(struct input_polled_dev *dev)
y = ((int)(s8)buf[3] << 4) | (buf[2] & 0xf);
z = ((int)(s8)buf[5] << 4) | (buf[4] & 0xf);
- input_report_abs(dev->input, ABS_X, x);
- input_report_abs(dev->input, ABS_Y, y);
- input_report_abs(dev->input, ABS_Z, z);
- input_sync(dev->input);
+ input_report_abs(input, ABS_X, x);
+ input_report_abs(input, ABS_Y, y);
+ input_report_abs(input, ABS_Z, z);
+ input_sync(input);
}
/* Initialize the MMA8450 chip */
-static void mma8450_open(struct input_polled_dev *dev)
+static int mma8450_open(struct input_dev *input)
{
- struct mma8450 *m = dev->private;
+ struct i2c_client *c = input_get_drvdata(input);
int err;
/* enable all events from X/Y/Z, no FIFO */
- err = mma8450_write(m, MMA8450_XYZ_DATA_CFG, 0x07);
+ err = mma8450_write(c, MMA8450_XYZ_DATA_CFG, 0x07);
if (err)
- return;
+ return err;
/*
* Sleep mode poll rate - 50Hz
* System output data rate - 400Hz
* Full scale selection - Active, +/- 2G
*/
- err = mma8450_write(m, MMA8450_CTRL_REG1, 0x01);
- if (err < 0)
- return;
+ err = mma8450_write(c, MMA8450_CTRL_REG1, 0x01);
+ if (err)
+ return err;
msleep(MODE_CHANGE_DELAY_MS);
+ return 0;
}
-static void mma8450_close(struct input_polled_dev *dev)
+static void mma8450_close(struct input_dev *input)
{
- struct mma8450 *m = dev->private;
+ struct i2c_client *c = input_get_drvdata(input);
- mma8450_write(m, MMA8450_CTRL_REG1, 0x00);
- mma8450_write(m, MMA8450_CTRL_REG2, 0x01);
+ mma8450_write(c, MMA8450_CTRL_REG1, 0x00);
+ mma8450_write(c, MMA8450_CTRL_REG2, 0x01);
}
/*
@@ -157,38 +149,37 @@ static void mma8450_close(struct input_polled_dev *dev)
static int mma8450_probe(struct i2c_client *c,
const struct i2c_device_id *id)
{
- struct input_polled_dev *idev;
- struct mma8450 *m;
+ struct input_dev *input;
int err;
- m = devm_kzalloc(&c->dev, sizeof(*m), GFP_KERNEL);
- if (!m)
+ input = devm_input_allocate_device(&c->dev);
+ if (!input)
return -ENOMEM;
- idev = devm_input_allocate_polled_device(&c->dev);
- if (!idev)
- return -ENOMEM;
+ input_set_drvdata(input, c);
+
+ input->name = MMA8450_DRV_NAME;
+ input->id.bustype = BUS_I2C;
+
+ input->open = mma8450_open;
+ input->close = mma8450_close;
- m->client = c;
- m->idev = idev;
+ input_set_abs_params(input, ABS_X, -2048, 2047, 32, 32);
+ input_set_abs_params(input, ABS_Y, -2048, 2047, 32, 32);
+ input_set_abs_params(input, ABS_Z, -2048, 2047, 32, 32);
- idev->private = m;
- idev->input->name = MMA8450_DRV_NAME;
- idev->input->id.bustype = BUS_I2C;
- idev->poll = mma8450_poll;
- idev->poll_interval = POLL_INTERVAL;
- idev->poll_interval_max = POLL_INTERVAL_MAX;
- idev->open = mma8450_open;
- idev->close = mma8450_close;
+ err = input_setup_polling(input, mma8450_poll);
+ if (err) {
+ dev_err(&c->dev, "failed to set up polling\n");
+ return err;
+ }
- __set_bit(EV_ABS, idev->input->evbit);
- input_set_abs_params(idev->input, ABS_X, -2048, 2047, 32, 32);
- input_set_abs_params(idev->input, ABS_Y, -2048, 2047, 32, 32);
- input_set_abs_params(idev->input, ABS_Z, -2048, 2047, 32, 32);
+ input_set_poll_interval(input, POLL_INTERVAL);
+ input_set_max_poll_interval(input, POLL_INTERVAL_MAX);
- err = input_register_polled_device(idev);
+ err = input_register_device(input);
if (err) {
- dev_err(&c->dev, "failed to register polled input device\n");
+ dev_err(&c->dev, "failed to register input device\n");
return err;
}
We have added polled mode to the normal input devices with the intent of retiring input_polled_dev. This converts mma8450 driver to use the polling mode of standard input devices and removes dependency on INPUT_POLLDEV. Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> --- drivers/input/misc/Kconfig | 1 - drivers/input/misc/mma8450.c | 101 ++++++++++++++++------------------- 2 files changed, 46 insertions(+), 56 deletions(-)