diff mbox

[2/6] elantech: distinguish various hardware/firmware versions

Message ID 4DCE252E.2040403@tudelft.nl (mailing list archive)
State New, archived
Headers show

Commit Message

Éric Piel May 14, 2011, 6:46 a.m. UTC
According to the protocol document, there are a couple of different
versions of the hardware and firmware. Using the version number, it
should be possible to distinguish between them, at least for the
properties we care about.

Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
---
 drivers/input/mouse/elantech.c |   34 +++++++++++++++++++++-------------
 drivers/input/mouse/elantech.h |   10 +++++++++-
 2 files changed, 30 insertions(+), 14 deletions(-)
diff mbox

Patch

diff --git a/drivers/input/mouse/elantech.c b/drivers/input/mouse/elantech.c
index 04d9bf3..badb2ea 100644
--- a/drivers/input/mouse/elantech.c
+++ b/drivers/input/mouse/elantech.c
@@ -719,15 +719,32 @@  int elantech_init(struct psmouse *psmouse)
 	 * Assume every version greater than this is new EeePC style
 	 * hardware with 6 byte packets
 	 */
-	if (etd->fw_version >= 0x020030) {
+	if (etd->fw_version >= 0x020800) {
 		etd->hw_version = 2;
 		/* For now show extra debug information */
 		etd->debug = 1;
-		/* Don't know how to do parity checking for version 2 */
-		etd->paritycheck = 0;
+		etd->paritycheck = ETP_CONST_CHECK;
+		etd->reports_pres = 1;
+	} else if (etd->fw_version == 0x020030) {
+		etd->hw_version = 2;
+		/* For now show extra debug information */
+		etd->debug = 1;
+		etd->paritycheck = ETP_EF113_CHECK;
+		etd->reports_pres = 0;
+	} else if ((etd->fw_version == 0x020022) || (etd->fw_version == 0x020600)) {
+		/*
+		 * This firmware suffers from misreporting coordinates when
+		 * a touch action starts causing the mouse cursor or scrolled page
+		 * to jump. Enable a workaround.
+		 */
+		pr_info("firmware version 2.0.34/2.6.0 detected, enabling jumpy cursor workaround\n");
+		etd->jumpy_cursor = 1;
+		etd->debug = 1;
+		etd->hw_version = 1;
+		etd->paritycheck = ETP_FULL_PC;
 	} else {
 		etd->hw_version = 1;
-		etd->paritycheck = 1;
+		etd->paritycheck = ETP_FULL_PC;
 	}
 
 	pr_info("assuming hardware version %d, firmware version %d.%d.%d\n",
@@ -741,15 +758,6 @@  int elantech_init(struct psmouse *psmouse)
 		param[0], param[1], param[2]);
 	etd->capabilities = param[0];
 
-	/*
-	 * This firmware suffers from misreporting coordinates when
-	 * a touch action starts causing the mouse cursor or scrolled page
-	 * to jump. Enable a workaround.
-	 */
-	if (etd->fw_version == 0x020022 || etd->fw_version == 0x020600) {
-		pr_info("firmware version 2.0.34/2.6.0 detected, enabling jumpy cursor workaround\n");
-		etd->jumpy_cursor = true;
-	}
 
 	if (elantech_set_absolute_mode(psmouse)) {
 		pr_err("failed to put touchpad into absolute mode.\n");
diff --git a/drivers/input/mouse/elantech.h b/drivers/input/mouse/elantech.h
index aa4aac5..257d419 100644
--- a/drivers/input/mouse/elantech.h
+++ b/drivers/input/mouse/elantech.h
@@ -100,14 +100,22 @@  struct elantech_data {
 	unsigned char reg_26;
 	unsigned char debug;
 	unsigned char capabilities;
-	bool paritycheck;
+	unsigned char paritycheck;
 	bool jumpy_cursor;
+	unsigned char reports_pres :1;
 	unsigned char hw_version;
 	unsigned int fw_version;
 	unsigned int single_finger_reports;
 	unsigned char parity[256];
 };
 
+enum paritycheck_types {
+	ETP_NOT_CHECK = 0,
+	ETP_FULL_PC,	 /* used in 4-byte protocol */
+	ETP_EF113_CHECK, /* check used only on the EF113 */
+	ETP_CONST_CHECK, /* used in 6-byte protocol, only checking constant bits */
+};
+
 #ifdef CONFIG_MOUSE_PS2_ELANTECH
 int elantech_detect(struct psmouse *psmouse, bool set_properties);
 int elantech_init(struct psmouse *psmouse);