@@ -200,78 +200,6 @@ static int mt9v022_s_stream(struct v4l2_subdev *sd, int enable)
return 0;
}
-static int mt9v022_set_bus_param(struct soc_camera_device *icd,
- unsigned long flags)
-{
- struct i2c_client *client = to_i2c_client(to_soc_camera_control(icd));
- struct mt9v022 *mt9v022 = to_mt9v022(client);
- struct soc_camera_link *icl = to_soc_camera_link(icd);
- unsigned int width_flag = flags & SOCAM_DATAWIDTH_MASK;
- int ret;
- u16 pixclk = 0;
-
- /* Only one width bit may be set */
- if (!is_power_of_2(width_flag))
- return -EINVAL;
-
- if (icl->set_bus_param) {
- ret = icl->set_bus_param(icl, width_flag);
- if (ret)
- return ret;
- } else {
- /*
- * Without board specific bus width settings we only support the
- * sensors native bus width
- */
- if (width_flag != SOCAM_DATAWIDTH_10)
- return -EINVAL;
- }
-
- flags = soc_camera_apply_sensor_flags(icl, flags);
-
- if (flags & SOCAM_PCLK_SAMPLE_FALLING)
- pixclk |= 0x10;
-
- if (!(flags & SOCAM_HSYNC_ACTIVE_HIGH))
- pixclk |= 0x1;
-
- if (!(flags & SOCAM_VSYNC_ACTIVE_HIGH))
- pixclk |= 0x2;
-
- ret = reg_write(client, MT9V022_PIXCLK_FV_LV, pixclk);
- if (ret < 0)
- return ret;
-
- if (!(flags & SOCAM_MASTER))
- mt9v022->chip_control &= ~0x8;
-
- ret = reg_write(client, MT9V022_CHIP_CONTROL, mt9v022->chip_control);
- if (ret < 0)
- return ret;
-
- dev_dbg(&client->dev, "Calculated pixclk 0x%x, chip control 0x%x\n",
- pixclk, mt9v022->chip_control);
-
- return 0;
-}
-
-static unsigned long mt9v022_query_bus_param(struct soc_camera_device *icd)
-{
- struct soc_camera_link *icl = to_soc_camera_link(icd);
- unsigned int flags = SOCAM_MASTER | SOCAM_SLAVE |
- SOCAM_PCLK_SAMPLE_RISING | SOCAM_PCLK_SAMPLE_FALLING |
- SOCAM_HSYNC_ACTIVE_HIGH | SOCAM_HSYNC_ACTIVE_LOW |
- SOCAM_VSYNC_ACTIVE_HIGH | SOCAM_VSYNC_ACTIVE_LOW |
- SOCAM_DATA_ACTIVE_HIGH;
-
- if (icl->query_bus_param)
- flags |= icl->query_bus_param(icl) & SOCAM_DATAWIDTH_MASK;
- else
- flags |= SOCAM_DATAWIDTH_10;
-
- return soc_camera_apply_sensor_flags(icl, flags);
-}
-
static int mt9v022_s_crop(struct v4l2_subdev *sd, struct v4l2_crop *a)
{
struct i2c_client *client = v4l2_get_subdevdata(sd);
@@ -558,8 +486,6 @@ static const struct v4l2_queryctrl mt9v022_controls[] = {
};
static struct soc_camera_ops mt9v022_ops = {
- .set_bus_param = mt9v022_set_bus_param,
- .query_bus_param = mt9v022_query_bus_param,
.controls = mt9v022_controls,
.num_controls = ARRAY_SIZE(mt9v022_controls),
};
Now that all soc-camera hosts have been ported to use V4L2 subdevice mediabus-config operations and soc-camera client bus-parameter operations have been made optional, they can be removed. Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> --- drivers/media/video/mt9v022.c | 74 ----------------------------------------- 1 files changed, 0 insertions(+), 74 deletions(-)