@@ -4401,9 +4401,7 @@ static void tibetCS16_init(struct bttv *btv)
* is {3, 0, 2, 1}, i.e. the first controller to be detected is logical
* unit 3, the second (which is the master) is logical unit 0, etc.
* We need to maintain the status of the analog switch (which of the 16
- * cameras is connected to which of the 4 controllers). Rather than
- * add to the bttv structure for this, we use the data reserved for
- * the mbox (unused for this card type).
+ * cameras is connected to which of the 4 controllers) in sw_status array.
*/
/*
@@ -4438,7 +4436,6 @@ static void kodicom4400r_write(struct bttv *btv,
*/
static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input)
{
- char *sw_status;
int xaddr, yaddr;
struct bttv *mctlr;
static unsigned char map[4] = {3, 0, 2, 1};
@@ -4449,14 +4446,13 @@ static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input)
}
yaddr = (btv->c.nr - mctlr->c.nr + 1) & 3; /* the '&' is for safety */
yaddr = map[yaddr];
- sw_status = (char *)(&mctlr->mbox_we);
xaddr = input & 0xf;
/* Check if the controller/camera pair has changed, else ignore */
- if (sw_status[yaddr] != xaddr)
+ if (mctlr->sw_status[yaddr] != xaddr)
{
/* "open" the old switch, "close" the new one, save the new */
- kodicom4400r_write(mctlr, sw_status[yaddr], yaddr, 0);
- sw_status[yaddr] = xaddr;
+ kodicom4400r_write(mctlr, mctlr->sw_status[yaddr], yaddr, 0);
+ mctlr->sw_status[yaddr] = xaddr;
kodicom4400r_write(mctlr, xaddr, yaddr, 1);
}
}
@@ -4469,7 +4465,6 @@ static void kodicom4400r_muxsel(struct bttv *btv, unsigned int input)
*/
static void kodicom4400r_init(struct bttv *btv)
{
- char *sw_status = (char *)(&btv->mbox_we);
int ix;
gpio_inout(0x0003ff, 0x0003ff);
@@ -4477,7 +4472,7 @@ static void kodicom4400r_init(struct bttv *btv)
gpio_write(0);
/* Preset camera 0 to the 4 controllers */
for (ix = 0; ix < 4; ix++) {
- sw_status[ix] = ix;
+ btv->sw_status[ix] = ix;
kodicom4400r_write(btv, ix, ix, 1);
}
/*
@@ -4754,7 +4749,6 @@ static void gv800s_write(struct bttv *btv,
static void gv800s_muxsel(struct bttv *btv, unsigned int input)
{
struct bttv *mctlr;
- char *sw_status;
int xaddr, yaddr;
static unsigned int map[4][4] = { { 0x0, 0x4, 0xa, 0x6 },
{ 0x1, 0x5, 0xb, 0x7 },
@@ -4767,14 +4761,13 @@ static void gv800s_muxsel(struct bttv *btv, unsigned int input)
return;
}
yaddr = (btv->c.nr - mctlr->c.nr) & 3;
- sw_status = (char *)(&mctlr->mbox_we);
xaddr = map[yaddr][input] & 0xf;
/* Check if the controller/camera pair has changed, ignore otherwise */
- if (sw_status[yaddr] != xaddr) {
+ if (mctlr->sw_status[yaddr] != xaddr) {
/* disable the old switch, enable the new one and save status */
- gv800s_write(mctlr, sw_status[yaddr], yaddr, 0);
- sw_status[yaddr] = xaddr;
+ gv800s_write(mctlr, mctlr->sw_status[yaddr], yaddr, 0);
+ mctlr->sw_status[yaddr] = xaddr;
gv800s_write(mctlr, xaddr, yaddr, 1);
}
}
@@ -4782,7 +4775,6 @@ static void gv800s_muxsel(struct bttv *btv, unsigned int input)
/* GeoVision GV-800(S) "master" chip init */
static void gv800s_init(struct bttv *btv)
{
- char *sw_status = (char *)(&btv->mbox_we);
int ix;
gpio_inout(0xf107f, 0xf107f);
@@ -4791,7 +4783,7 @@ static void gv800s_init(struct bttv *btv)
/* Preset camera 0 to the 4 controllers */
for (ix = 0; ix < 4; ix++) {
- sw_status[ix] = ix;
+ btv->sw_status[ix] = ix;
gv800s_write(btv, ix, ix, 1);
}
@@ -459,6 +459,9 @@ struct bttv {
int mbox_iow;
int mbox_csel;
+ /* switch status for multi-controller cards */
+ char sw_status[4];
+
/* risc memory management data
- must acquire s_lock before changing these
- only the irq handler is supported to touch top + bottom + vcurr */
Kodicom 4400R and Geovision GV-800 code in bttv driver abuses mbox_we (int) in struct bttv as char *. Remove this hack and add a proper sw_status array to struct bttv instead. This is a a preparation to remove mbox_we. Signed-off-by: Ondrej Zary <linux@rainbow-software.org> --- drivers/media/pci/bt8xx/bttv-cards.c | 26 +++++++++----------------- drivers/media/pci/bt8xx/bttvp.h | 3 +++ 2 files changed, 12 insertions(+), 17 deletions(-)