@@ -29,7 +29,6 @@
* A value of 0 (default) or lower indicates that
* the correct number of parameters will be
* automatically detected.
- * @load_firmware_sync: Force the firmware load to be synchronous.
*
* On the *_gpio vars, bit 0 is UIO-1, bit 1 is UIO-2 and bit 2 is
* UIO-3.
@@ -41,7 +40,6 @@ struct drxk_config {
bool parallel_ts;
bool dynamic_clk;
bool enable_merr_cfg;
- bool load_firmware_sync;
bool antenna_dvbt;
u16 antenna_gpio;
@@ -6830,25 +6830,13 @@ struct dvb_frontend *drxk_attach(const struct drxk_config *config,
/* Load firmware and initialize DRX-K */
if (state->microcode_name) {
- if (config->load_firmware_sync) {
- const struct firmware *fw = NULL;
+ const struct firmware *fw = NULL;
- status = request_firmware(&fw, state->microcode_name,
- state->i2c->dev.parent);
- if (status < 0)
- fw = NULL;
- load_firmware_cb(fw, state);
- } else {
- status = request_firmware_nowait(THIS_MODULE, 1,
- state->microcode_name,
- state->i2c->dev.parent,
- GFP_KERNEL,
- state, load_firmware_cb);
- if (status < 0) {
- pr_err("failed to request a firmware\n");
- return NULL;
- }
- }
+ status = request_firmware(&fw, state->microcode_name,
+ state->i2c->dev.parent);
+ if (status < 0)
+ fw = NULL;
+ load_firmware_cb(fw, state);
} else if (init_drxk(state) < 0)
goto error;
@@ -375,7 +375,6 @@ static struct drxk_config terratec_h5_drxk = {
.no_i2c_bridge = 1,
.microcode_name = "dvb-usb-terratec-h5-drxk.fw",
.qam_demod_parameter_count = 2,
- .load_firmware_sync = true,
};
static struct drxk_config hauppauge_930c_drxk = {
@@ -385,7 +384,6 @@ static struct drxk_config hauppauge_930c_drxk = {
.microcode_name = "dvb-usb-hauppauge-hvr930c-drxk.fw",
.chunk_size = 56,
.qam_demod_parameter_count = 2,
- .load_firmware_sync = true,
};
static struct drxk_config terratec_htc_stick_drxk = {
@@ -399,7 +397,6 @@ static struct drxk_config terratec_htc_stick_drxk = {
.antenna_dvbt = true,
/* The windows driver uses the same. This will disable LNA. */
.antenna_gpio = 0x6,
- .load_firmware_sync = true,
};
static struct drxk_config maxmedia_ub425_tc_drxk = {
@@ -408,7 +405,6 @@ static struct drxk_config maxmedia_ub425_tc_drxk = {
.no_i2c_bridge = 1,
.microcode_name = "dvb-demod-drxk-01.fw",
.chunk_size = 62,
- .load_firmware_sync = true,
.qam_demod_parameter_count = 2,
};
@@ -420,7 +416,6 @@ static struct drxk_config pctv_520e_drxk = {
.chunk_size = 58,
.antenna_dvbt = true, /* disable LNA */
.antenna_gpio = (1 << 2), /* disable LNA */
- .load_firmware_sync = true,
};
static int drxk_gate_ctrl(struct dvb_frontend *fe, int enable)
The option to load firmware asynchronously were added due to a requirement with a few versions of udev. It turns that this was a bad idea and caused regressions on drxk-based devices. So, we end by only letting the firmware to be loaded syncronously everywhere. So, let's remove the bad code. This patch partially reverts the changeset 8e30783b0b3. Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com> --- drivers/media/dvb-frontends/drxk.h | 2 -- drivers/media/dvb-frontends/drxk_hard.c | 24 ++++++------------------ drivers/media/usb/em28xx/em28xx-dvb.c | 5 ----- 3 files changed, 6 insertions(+), 25 deletions(-)