| Message ID | 1418892667-27428-6-git-send-email-josh.wu@atmel.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Josh, On 18/12/2014 at 16:51:05 +0800, Josh Wu wrote : > For sama5d3xmb board, the pins: pinctrl_isi_{power,reset} is used to > power-down or reset camera sensor. > > So we should let camera sensor instead of ISI to configure the pins. > This patch will change pinctrl name from pinctrl_isi_{power,reset} to > pinctrl_sensor_{power,reset}. > > Signed-off-by: Josh Wu <josh.wu@atmel.com> > --- > arch/arm/boot/dts/sama5d3.dtsi | 2 ++ > arch/arm/boot/dts/sama5d3xmb.dtsi | 6 ++---- > 2 files changed, 4 insertions(+), 4 deletions(-) > > diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi > index ed734e9..ff0fa3a 100644 > --- a/arch/arm/boot/dts/sama5d3.dtsi > +++ b/arch/arm/boot/dts/sama5d3.dtsi > @@ -214,6 +214,8 @@ > compatible = "atmel,at91sam9g45-isi"; > reg = <0xf0034000 0x4000>; > interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_isi_data_0_7>; This should probably not be is that patch. > clocks = <&isi_clk>; > clock-names = "isi_clk"; > status = "disabled"; > diff --git a/arch/arm/boot/dts/sama5d3xmb.dtsi b/arch/arm/boot/dts/sama5d3xmb.dtsi > index 6af1cba..0aaebc6 100644 > --- a/arch/arm/boot/dts/sama5d3xmb.dtsi > +++ b/arch/arm/boot/dts/sama5d3xmb.dtsi > @@ -60,8 +60,6 @@ > }; > > isi: isi@f0034000 { > - pinctrl-names = "default"; > - pinctrl-0 = <&pinctrl_isi_data_0_7 &pinctrl_isi_pck_as_mck &pinctrl_isi_power &pinctrl_isi_reset>; > }; > > mmc1: mmc@f8000000 { > @@ -122,12 +120,12 @@ > <AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD31 periph B ISI_MCK */ > }; > > - pinctrl_isi_reset: isi_reset-0 { > + pinctrl_sensor_reset: sensor_reset-0 { > atmel,pins = > <AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE24 gpio */ > }; > > - pinctrl_isi_power: isi_power-0 { > + pinctrl_sensor_power: sensor_power-0 { > atmel,pins = > <AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE29 gpio */ > }; > -- > 1.9.1 >
diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi index ed734e9..ff0fa3a 100644 --- a/arch/arm/boot/dts/sama5d3.dtsi +++ b/arch/arm/boot/dts/sama5d3.dtsi @@ -214,6 +214,8 @@ compatible = "atmel,at91sam9g45-isi"; reg = <0xf0034000 0x4000>; interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_isi_data_0_7>; clocks = <&isi_clk>; clock-names = "isi_clk"; status = "disabled"; diff --git a/arch/arm/boot/dts/sama5d3xmb.dtsi b/arch/arm/boot/dts/sama5d3xmb.dtsi index 6af1cba..0aaebc6 100644 --- a/arch/arm/boot/dts/sama5d3xmb.dtsi +++ b/arch/arm/boot/dts/sama5d3xmb.dtsi @@ -60,8 +60,6 @@ }; isi: isi@f0034000 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_isi_data_0_7 &pinctrl_isi_pck_as_mck &pinctrl_isi_power &pinctrl_isi_reset>; }; mmc1: mmc@f8000000 { @@ -122,12 +120,12 @@ <AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD31 periph B ISI_MCK */ }; - pinctrl_isi_reset: isi_reset-0 { + pinctrl_sensor_reset: sensor_reset-0 { atmel,pins = <AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE24 gpio */ }; - pinctrl_isi_power: isi_power-0 { + pinctrl_sensor_power: sensor_power-0 { atmel,pins = <AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE29 gpio */ };
For sama5d3xmb board, the pins: pinctrl_isi_{power,reset} is used to power-down or reset camera sensor. So we should let camera sensor instead of ISI to configure the pins. This patch will change pinctrl name from pinctrl_isi_{power,reset} to pinctrl_sensor_{power,reset}. Signed-off-by: Josh Wu <josh.wu@atmel.com> --- arch/arm/boot/dts/sama5d3.dtsi | 2 ++ arch/arm/boot/dts/sama5d3xmb.dtsi | 6 ++---- 2 files changed, 4 insertions(+), 4 deletions(-)