diff mbox

[v4,12/12] DT: aat1290: Document handling external strobe sources

Message ID 1427810265-25651-3-git-send-email-j.anaszewski@samsung.com (mailing list archive)
State New, archived
Headers show

Commit Message

Jacek Anaszewski March 31, 2015, 1:57 p.m. UTC 
This patch adds documentation for a pinctrl-names property.
The property, when present, is used for switching the source
of the strobe signal for the device.

Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: devicetree@vger.kernel.org
---
 .../devicetree/bindings/leds/leds-aat1290.txt      |   32 +++++++++++++++++++-
 1 file changed, 31 insertions(+), 1 deletion(-)
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/leds/leds-aat1290.txt b/Documentation/devicetree/bindings/leds/leds-aat1290.txt
index 6893eb1..c3df4e9 100644
--- a/Documentation/devicetree/bindings/leds/leds-aat1290.txt
+++ b/Documentation/devicetree/bindings/leds/leds-aat1290.txt
@@ -2,7 +2,9 @@ 
 
 The device is controlled through two pins: FL_EN and EN_SET. The pins when,
 asserted high, enable flash strobe and movie mode (max 1/2 of flash current)
-respectively.
+respectively. In order to add a capability of selecting the strobe signal source
+(e.g. GPIO or ISP) there is an additional switch required, independent of the
+flash chip. The switch is controlled with pin control.
 
 Required properties:
 
@@ -10,6 +12,13 @@  Required properties:
 - flen-gpios : Must be device tree identifier of the flash device FL_EN pin.
 - enset-gpios : Must be device tree identifier of the flash device EN_SET pin.
 
+Optional properties:
+- pinctrl-names : Must contain entries: "default", "host", "isp". Entries
+		"default" and "host" must refer to the same pin configuration
+		node, which sets the host as a strobe signal provider. Entry
+		"isp" must refer to the pin configuration node, which sets the
+		ISP as a strobe signal provider.
+
 A discrete LED element connected to the device must be represented by a child
 node - see Documentation/devicetree/bindings/leds/common.txt.
 
@@ -27,14 +36,35 @@  Optional properties of the LED child node:
 Example (by Ct = 220nF, Rset = 160kohm and exynos4412-trats2 board with
 a switch that allows for routing strobe signal either from host or from ISP):
 
+#include "exynos4412.dtsi"
+
 aat1290 {
 	compatible = "skyworks,aat1290";
 	flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>;
 	enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>;
 
+	pinctrl-names = "default", "host", "isp";
+	pinctrl-0 = <&camera_flash_host>;
+	pinctrl-1 = <&camera_flash_host>;
+	pinctrl-2 = <&camera_flash_isp>;
+
 	camera_flash: flash-led {
 		label = "aat1290-flash";
 		flash-max-microamp = <1012500>;
 		flash-timeout-us = <1940000>;
 	};
 };
+
+&pinctrl_0 {
+	camera_flash_host: camera-flash-host {
+		samsung,pins = "gpj1-0";
+		samsung,pin-function = <1>;
+		samsung,pin-val = <0>;
+	};
+
+	camera_flash_isp: camera-flash-isp {
+		samsung,pins = "gpj1-0";
+		samsung,pin-function = <1>;
+		samsung,pin-val = <1>;
+	};
+};