@@ -179,42 +179,6 @@ static inline struct au8522_state *to_state(struct v4l2_subdev *sd)
return container_of(sd, struct au8522_state, sd);
}
-static void setup_vbi(struct au8522_state *state, int aud_input)
-{
- int i;
-
- /* These are set to zero regardless of what mode we're in */
- au8522_writereg(state, AU8522_TVDEC_VBI_CTRL_H_REG017H, 0x00);
- au8522_writereg(state, AU8522_TVDEC_VBI_CTRL_L_REG018H, 0x00);
- au8522_writereg(state, AU8522_TVDEC_VBI_USER_TOTAL_BITS_REG019H, 0x00);
- au8522_writereg(state, AU8522_TVDEC_VBI_USER_TUNIT_H_REG01AH, 0x00);
- au8522_writereg(state, AU8522_TVDEC_VBI_USER_TUNIT_L_REG01BH, 0x00);
- au8522_writereg(state, AU8522_TVDEC_VBI_USER_THRESH1_REG01CH, 0x00);
- au8522_writereg(state, AU8522_TVDEC_VBI_USER_FRAME_PAT2_REG01EH, 0x00);
- au8522_writereg(state, AU8522_TVDEC_VBI_USER_FRAME_PAT1_REG01FH, 0x00);
- au8522_writereg(state, AU8522_TVDEC_VBI_USER_FRAME_PAT0_REG020H, 0x00);
- au8522_writereg(state, AU8522_TVDEC_VBI_USER_FRAME_MASK2_REG021H,
- 0x00);
- au8522_writereg(state, AU8522_TVDEC_VBI_USER_FRAME_MASK1_REG022H,
- 0x00);
- au8522_writereg(state, AU8522_TVDEC_VBI_USER_FRAME_MASK0_REG023H,
- 0x00);
-
- /* Setup the VBI registers */
- for (i = 0x30; i < 0x60; i++)
- au8522_writereg(state, i, 0x40);
-
- /* For some reason, every register is 0x40 except register 0x44
- (confirmed via the HVR-950q USB capture) */
- au8522_writereg(state, 0x44, 0x60);
-
- /* Enable VBI (we always do this regardless of whether the user is
- viewing closed caption info) */
- au8522_writereg(state, AU8522_TVDEC_VBI_CTRL_H_REG017H,
- AU8522_TVDEC_VBI_CTRL_H_REG017H_CCON);
-
-}
-
static void setup_decoder_defaults(struct au8522_state *state, bool is_svideo)
{
int i;
@@ -317,8 +281,6 @@ static void setup_decoder_defaults(struct au8522_state *state, bool is_svideo)
AU8522_TOREGAAGC_REG0E5H_CVBS);
au8522_writereg(state, AU8522_REG016H, AU8522_REG016H_CVBS);
- setup_vbi(state, 0);
-
if (is_svideo) {
/* Despite what the table says, for the HVR-950q we still need
to be in CVBS mode for the S-Video input (reason unknown). */
Since we don't suppoort sliced VBI with the au0828/au8522, there is no need to configure the au8522 VBI slicer, which because of the coefficients requires a large amount of i2c traffic. Remove the relevant code. Note that this has no effect on raw VBI support, which is currently the only supported way to access VBI on this device. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> --- drivers/media/dvb-frontends/au8522_decoder.c | 38 ---------------------------- 1 file changed, 38 deletions(-)