| Message ID | 20180215133335.9335-2-maxime.ripard@bootlin.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Maxime, Thanks for your patch. On 2018-02-15 14:33:34 +0100, Maxime Ripard wrote: > The Cadence MIPI-CSI2 RX controller is a CSI2RX bridge that supports up to > 4 CSI-2 lanes, and can route the frames to up to 4 streams, depending on > the hardware implementation. > > It can operate with an external D-PHY, an internal one or no D-PHY at all > in some configurations. > > Acked-by: Rob Herring <robh@kernel.org> > Acked-by: Benoit Parrot <bparrot@ti.com> > Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> > Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Shall this file be added to MAINTAINERS? This can be done in a follow up patch, but if you respin please consider it. Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> > --- > .../devicetree/bindings/media/cdns,csi2rx.txt | 100 +++++++++++++++++++++ > 1 file changed, 100 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/cdns,csi2rx.txt > > diff --git a/Documentation/devicetree/bindings/media/cdns,csi2rx.txt b/Documentation/devicetree/bindings/media/cdns,csi2rx.txt > new file mode 100644 > index 000000000000..6b02a0657ad9 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/cdns,csi2rx.txt > @@ -0,0 +1,100 @@ > +Cadence MIPI-CSI2 RX controller > +=============================== > + > +The Cadence MIPI-CSI2 RX controller is a CSI-2 bridge supporting up to 4 CSI > +lanes in input, and 4 different pixel streams in output. > + > +Required properties: > + - compatible: must be set to "cdns,csi2rx" and an SoC-specific compatible > + - reg: base address and size of the memory mapped region > + - clocks: phandles to the clocks driving the controller > + - clock-names: must contain: > + * sys_clk: main clock > + * p_clk: register bank clock > + * pixel_if[0-3]_clk: pixel stream output clock, one for each stream > + implemented in hardware, between 0 and 3 > + > +Optional properties: > + - phys: phandle to the external D-PHY, phy-names must be provided > + - phy-names: must contain "dphy", if the implementation uses an > + external D-PHY > + > +Required subnodes: > + - ports: A ports node with one port child node per device input and output > + port, in accordance with the video interface bindings defined in > + Documentation/devicetree/bindings/media/video-interfaces.txt. The > + port nodes are numbered as follows: > + > + Port Description > + ----------------------------- > + 0 CSI-2 input > + 1 Stream 0 output > + 2 Stream 1 output > + 3 Stream 2 output > + 4 Stream 3 output > + > + The stream output port nodes are optional if they are not > + connected to anything at the hardware level or implemented > + in the design.Since there is only one endpoint per port, > + the endpoints are not numbered. > + > + > +Example: > + > +csi2rx: csi-bridge@0d060000 { > + compatible = "cdns,csi2rx"; > + reg = <0x0d060000 0x1000>; > + clocks = <&byteclock>, <&byteclock> > + <&coreclock>, <&coreclock>, > + <&coreclock>, <&coreclock>; > + clock-names = "sys_clk", "p_clk", > + "pixel_if0_clk", "pixel_if1_clk", > + "pixel_if2_clk", "pixel_if3_clk"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + csi2rx_in_sensor: endpoint { > + remote-endpoint = <&sensor_out_csi2rx>; > + clock-lanes = <0>; > + data-lanes = <1 2>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + csi2rx_out_grabber0: endpoint { > + remote-endpoint = <&grabber0_in_csi2rx>; > + }; > + }; > + > + port@2 { > + reg = <2>; > + > + csi2rx_out_grabber1: endpoint { > + remote-endpoint = <&grabber1_in_csi2rx>; > + }; > + }; > + > + port@3 { > + reg = <3>; > + > + csi2rx_out_grabber2: endpoint { > + remote-endpoint = <&grabber2_in_csi2rx>; > + }; > + }; > + > + port@4 { > + reg = <4>; > + > + csi2rx_out_grabber3: endpoint { > + remote-endpoint = <&grabber3_in_csi2rx>; > + }; > + }; > + }; > +}; > -- > 2.14.3 >
diff --git a/Documentation/devicetree/bindings/media/cdns,csi2rx.txt b/Documentation/devicetree/bindings/media/cdns,csi2rx.txt new file mode 100644 index 000000000000..6b02a0657ad9 --- /dev/null +++ b/Documentation/devicetree/bindings/media/cdns,csi2rx.txt @@ -0,0 +1,100 @@ +Cadence MIPI-CSI2 RX controller +=============================== + +The Cadence MIPI-CSI2 RX controller is a CSI-2 bridge supporting up to 4 CSI +lanes in input, and 4 different pixel streams in output. + +Required properties: + - compatible: must be set to "cdns,csi2rx" and an SoC-specific compatible + - reg: base address and size of the memory mapped region + - clocks: phandles to the clocks driving the controller + - clock-names: must contain: + * sys_clk: main clock + * p_clk: register bank clock + * pixel_if[0-3]_clk: pixel stream output clock, one for each stream + implemented in hardware, between 0 and 3 + +Optional properties: + - phys: phandle to the external D-PHY, phy-names must be provided + - phy-names: must contain "dphy", if the implementation uses an + external D-PHY + +Required subnodes: + - ports: A ports node with one port child node per device input and output + port, in accordance with the video interface bindings defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + port nodes are numbered as follows: + + Port Description + ----------------------------- + 0 CSI-2 input + 1 Stream 0 output + 2 Stream 1 output + 3 Stream 2 output + 4 Stream 3 output + + The stream output port nodes are optional if they are not + connected to anything at the hardware level or implemented + in the design.Since there is only one endpoint per port, + the endpoints are not numbered. + + +Example: + +csi2rx: csi-bridge@0d060000 { + compatible = "cdns,csi2rx"; + reg = <0x0d060000 0x1000>; + clocks = <&byteclock>, <&byteclock> + <&coreclock>, <&coreclock>, + <&coreclock>, <&coreclock>; + clock-names = "sys_clk", "p_clk", + "pixel_if0_clk", "pixel_if1_clk", + "pixel_if2_clk", "pixel_if3_clk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + csi2rx_in_sensor: endpoint { + remote-endpoint = <&sensor_out_csi2rx>; + clock-lanes = <0>; + data-lanes = <1 2>; + }; + }; + + port@1 { + reg = <1>; + + csi2rx_out_grabber0: endpoint { + remote-endpoint = <&grabber0_in_csi2rx>; + }; + }; + + port@2 { + reg = <2>; + + csi2rx_out_grabber1: endpoint { + remote-endpoint = <&grabber1_in_csi2rx>; + }; + }; + + port@3 { + reg = <3>; + + csi2rx_out_grabber2: endpoint { + remote-endpoint = <&grabber2_in_csi2rx>; + }; + }; + + port@4 { + reg = <4>; + + csi2rx_out_grabber3: endpoint { + remote-endpoint = <&grabber3_in_csi2rx>; + }; + }; + }; +};