@@ -441,40 +441,25 @@ static void vpfe_ccdc_restore_defaults(struct vpfe_ccdc *ccdc)
static int vpfe_ccdc_close(struct vpfe_ccdc *ccdc, struct device *dev)
{
- int dma_cntl, i, pcr;
+ struct vpfe_device *vpfe = container_of(ccdc, struct vpfe_device, ccdc);
+ u32 dma_cntl, pcr;
- /* If the CCDC module is still busy wait for it to be done */
- for (i = 0; i < 10; i++) {
- usleep_range(5000, 6000);
- pcr = vpfe_reg_read(ccdc, VPFE_PCR);
- if (!pcr)
- break;
+ pcr = vpfe_reg_read(ccdc, VPFE_PCR);
+ if (pcr)
+ vpfe_dbg(1, vpfe, "VPFE_PCR is still set (%x)", pcr);
- /* make sure it it is disabled */
- vpfe_pcr_enable(ccdc, 0);
- }
+ dma_cntl = vpfe_reg_read(ccdc, VPFE_DMA_CNTL);
+ if ((dma_cntl & VPFE_DMA_CNTL_OVERFLOW))
+ vpfe_dbg(1, vpfe, "VPFE_DMA_CNTL_OVERFLOW is still set (%x)",
+ dma_cntl);
/* Disable CCDC by resetting all register to default POR values */
vpfe_ccdc_restore_defaults(ccdc);
- /* if DMA_CNTL overflow bit is set. Clear it
- * It appears to take a while for this to become quiescent ~20ms
- */
- for (i = 0; i < 10; i++) {
- dma_cntl = vpfe_reg_read(ccdc, VPFE_DMA_CNTL);
- if (!(dma_cntl & VPFE_DMA_CNTL_OVERFLOW))
- break;
-
- /* Clear the overflow bit */
- vpfe_reg_write(ccdc, dma_cntl, VPFE_DMA_CNTL);
- usleep_range(5000, 6000);
- }
-
/* Disabled the module at the CONFIG level */
vpfe_config_enable(ccdc, 0);
pm_runtime_put_sync(dev);
-
return 0;
}
@@ -1303,6 +1288,9 @@ static void vpfe_handle_interlaced_irq(struct vpfe_device *vpfe,
if (vpfe->cur_frm != vpfe->next_frm)
vpfe_process_buffer_complete(vpfe);
+ if (vpfe->stopping)
+ return;
+
/*
* based on whether the two fields are stored
* interleave or separately in memory,
@@ -1341,7 +1329,7 @@ static irqreturn_t vpfe_isr(int irq, void *dev)
{
struct vpfe_device *vpfe = (struct vpfe_device *)dev;
enum v4l2_field field = vpfe->fmt.fmt.pix.field;
- int intr_status;
+ int intr_status, stopping = vpfe->stopping;
intr_status = vpfe_reg_read(&vpfe->ccdc, VPFE_IRQ_STS);
@@ -1352,9 +1340,13 @@ static irqreturn_t vpfe_isr(int irq, void *dev)
} else {
vpfe_handle_interlaced_irq(vpfe, field);
}
+ if (stopping) {
+ vpfe->stopping = false;
+ complete(&vpfe->capture_stop);
+ }
}
- if (intr_status & VPFE_VDINT1) {
+ if (intr_status & VPFE_VDINT1 && !stopping) {
if (field == V4L2_FIELD_NONE &&
vpfe->cur_frm == vpfe->next_frm)
vpfe_schedule_next_buffer(vpfe);
@@ -1980,6 +1972,9 @@ static int vpfe_start_streaming(struct vb2_queue *vq, unsigned int count)
vpfe_attach_irq(vpfe);
+ vpfe->stopping = false;
+ init_completion(&vpfe->capture_stop);
+
if (vpfe->ccdc.ccdc_cfg.if_type == VPFE_RAW_BAYER)
vpfe_ccdc_config_raw(&vpfe->ccdc);
else
@@ -2032,6 +2027,11 @@ static void vpfe_stop_streaming(struct vb2_queue *vq)
vpfe_pcr_enable(&vpfe->ccdc, 0);
+ /* Wait for the last frame to be captured */
+ vpfe->stopping = true;
+ wait_for_completion_timeout(&vpfe->capture_stop,
+ msecs_to_jiffies(250));
+
vpfe_detach_irq(vpfe);
sdinfo = vpfe->current_subdev;
@@ -23,6 +23,7 @@
#include <linux/am437x-vpfe.h>
#include <linux/clk.h>
+#include <linux/completion.h>
#include <linux/device.h>
#include <linux/io.h>
#include <linux/i2c.h>
@@ -270,6 +271,8 @@ struct vpfe_device {
*/
u32 field_off;
struct vpfe_ccdc ccdc;
+ int stopping;
+ struct completion capture_stop;
};
#endif /* AM437X_VPFE_H */
We were originally attempting to stop all processing as soon as possible, but the in-progress DMA operation cannot be canceled. This led to the module being in a busy state and prevented proper power management functionality. The existing implementation would attempt to clean things up by waiting up to 50ms. However when receiving video frame at 15fps or lower, it meant an inter frame arrival rate of 66.6 ms or higher. In such cases upon tear down the following message could be seen: omap_hwmod: vpfe0: _wait_target_disable failed This patch fixes this issue by adding a stopping state where we would wait for the next Vsync before disabling the hardware. Signed-off-by: Benoit Parrot <bparrot@ti.com> --- drivers/media/platform/am437x/am437x-vpfe.c | 52 ++++++++++----------- drivers/media/platform/am437x/am437x-vpfe.h | 3 ++ 2 files changed, 29 insertions(+), 26 deletions(-)