@@ -1329,15 +1329,16 @@ usb3_phy1: usb-phy@382f0040 {
status = "disabled";
};
- vpu: video-codec@38300000 {
+ vpu_ctrl: syscon@38320000 {
+ compatible = "nxp,imx8mq-vpu-ctrl", "syscon";
+ reg = <0x38320000 0x10000>;
+ };
+
+ vpu_g1: video-codec@38300000 {
compatible = "nxp,imx8mq-vpu";
- reg = <0x38300000 0x10000>,
- <0x38310000 0x10000>,
- <0x38320000 0x10000>;
- reg-names = "g1", "g2", "ctrl";
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "g1", "g2";
+ reg = <0x38300000 0x10000>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "g1";
clocks = <&clk IMX8MQ_CLK_VPU_G1_ROOT>,
<&clk IMX8MQ_CLK_VPU_G2_ROOT>,
<&clk IMX8MQ_CLK_VPU_DEC_ROOT>;
@@ -1350,9 +1351,33 @@ vpu: video-codec@38300000 {
<&clk IMX8MQ_VPU_PLL_OUT>,
<&clk IMX8MQ_SYS1_PLL_800M>,
<&clk IMX8MQ_VPU_PLL>;
- assigned-clock-rates = <600000000>, <600000000>,
+ assigned-clock-rates = <600000000>, <300000000>,
+ <800000000>, <0>;
+ power-domains = <&pgc_vpu>;
+ nxp,imx8mq-vpu-ctrl = <&vpu_ctrl>;
+ };
+
+ vpu_g2: video-codec@38310000 {
+ compatible = "nxp,imx8mq-vpu-g2";
+ reg = <0x38310000 0x10000>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "g2";
+ clocks = <&clk IMX8MQ_CLK_VPU_G1_ROOT>,
+ <&clk IMX8MQ_CLK_VPU_G2_ROOT>,
+ <&clk IMX8MQ_CLK_VPU_DEC_ROOT>;
+ clock-names = "g1", "g2", "bus";
+ assigned-clocks = <&clk IMX8MQ_CLK_VPU_G1>,
+ <&clk IMX8MQ_CLK_VPU_G2>,
+ <&clk IMX8MQ_CLK_VPU_BUS>,
+ <&clk IMX8MQ_VPU_PLL_BYPASS>;
+ assigned-clock-parents = <&clk IMX8MQ_VPU_PLL_OUT>,
+ <&clk IMX8MQ_VPU_PLL_OUT>,
+ <&clk IMX8MQ_SYS1_PLL_800M>,
+ <&clk IMX8MQ_VPU_PLL>;
+ assigned-clock-rates = <600000000>, <300000000>,
<800000000>, <0>;
power-domains = <&pgc_vpu>;
+ nxp,imx8mq-vpu-ctrl = <&vpu_ctrl>;
};
pcie0: pcie@33800000 {
Split VPU node in two: one for G1 and one for G2 since they are different hardware blocks. Add syscon for hardware control block. Remove reg-names property that is useless. Each VPU node only need one interrupt. Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com> --- version 5: - use syscon instead of VPU reset arch/arm64/boot/dts/freescale/imx8mq.dtsi | 43 ++++++++++++++++++----- 1 file changed, 34 insertions(+), 9 deletions(-)