@@ -3658,6 +3658,7 @@ M: Raspberry Pi Kernel Maintenance <kernel-list@raspberrypi.com>
L: linux-media@vger.kernel.org
S: Maintained
F: Documentation/devicetree/bindings/media/brcm,bcm2835-unicam.yaml
+F: drivers/media/platform/bcm2835/
BROADCOM BCM47XX MIPS ARCHITECTURE
M: Hauke Mehrtens <hauke@hauke-m.de>
@@ -170,6 +170,7 @@ source "drivers/media/platform/am437x/Kconfig"
source "drivers/media/platform/xilinx/Kconfig"
source "drivers/media/platform/rcar-vin/Kconfig"
source "drivers/media/platform/atmel/Kconfig"
+source "drivers/media/platform/bcm2835/Kconfig"
source "drivers/media/platform/sunxi/Kconfig"
config VIDEO_TI_CAL
@@ -85,6 +85,8 @@ obj-$(CONFIG_VIDEO_QCOM_CAMSS) += qcom/camss/
obj-$(CONFIG_VIDEO_QCOM_VENUS) += qcom/venus/
+obj-y += bcm2835/
+
obj-y += sunxi/
obj-$(CONFIG_VIDEO_MESON_GE2D) += meson/ge2d/
new file mode 100644
@@ -0,0 +1,21 @@
+# Broadcom VideoCore4 V4L2 camera support
+
+config VIDEO_BCM2835_UNICAM
+ tristate "Broadcom BCM283x/BCM271x Unicam video capture driver"
+ depends on VIDEO_V4L2
+ depends on ARCH_BCM2835 || COMPILE_TEST
+ select VIDEO_V4L2_SUBDEV_API
+ select MEDIA_CONTROLLER
+ select VIDEOBUF2_DMA_CONTIG
+ select V4L2_FWNODE
+ help
+ Say Y here to enable support for the BCM283x/BCM271x CSI-2 receiver.
+ This is a V4L2 driver that controls the CSI-2 receiver directly,
+ independently from the VC4 firmware.
+ This driver is mutually exclusive with the use of bcm2835-camera. The
+ firmware will disable all access to the peripheral from within the
+ firmware if it finds a DT node using it, and bcm2835-camera will
+ therefore fail to probe.
+
+ To compile this driver as a module, choose M here. The module will be
+ called bcm2835-unicam.
new file mode 100644
@@ -0,0 +1,3 @@
+# Makefile for BCM2835 Unicam driver
+
+obj-$(CONFIG_VIDEO_BCM2835_UNICAM) += bcm2835-unicam.o
new file mode 100644
@@ -0,0 +1,2694 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * BCM283x / BCM271x Unicam Capture Driver
+ *
+ * Copyright (C) 2017-2020 - Raspberry Pi (Trading) Ltd.
+ *
+ * Dave Stevenson <dave.stevenson@raspberrypi.com>
+ *
+ * Based on TI am437x driver by
+ * Benoit Parrot <bparrot@ti.com>
+ * Lad, Prabhakar <prabhakar.csengg@gmail.com>
+ *
+ * and TI CAL camera interface driver by
+ * Benoit Parrot <bparrot@ti.com>
+ *
+ *
+ * There are two camera drivers in the kernel for BCM283x - this one
+ * and bcm2835-camera (currently in staging).
+ *
+ * This driver directly controls the Unicam peripheral - there is no
+ * involvement with the VideoCore firmware. Unicam receives CSI-2 or
+ * CCP2 data and writes it into SDRAM.
+ * The only potential processing options are to repack Bayer data into an
+ * alternate format, and applying windowing.
+ * The repacking does not shift the data, so can repack V4L2_PIX_FMT_Sxxxx10P
+ * to V4L2_PIX_FMT_Sxxxx10, or V4L2_PIX_FMT_Sxxxx12P to V4L2_PIX_FMT_Sxxxx12,
+ * but not generically up to V4L2_PIX_FMT_Sxxxx16. The driver will add both
+ * formats where the relevant formats are defined, and will automatically
+ * configure the repacking as required.
+ * Support for windowing may be added later.
+ *
+ * It should be possible to connect this driver to any sensor with a
+ * suitable output interface and V4L2 subdevice driver.
+ *
+ * bcm2835-camera uses the VideoCore firmware to control the sensor,
+ * Unicam, ISP, and all tuner control loops. Fully processed frames are
+ * delivered to the driver by the firmware. It only has sensor drivers
+ * for Omnivision OV5647, and Sony IMX219 sensors.
+ *
+ * The two drivers are mutually exclusive for the same Unicam instance.
+ * The VideoCore firmware checks the device tree configuration during boot.
+ * If it finds device tree nodes called csi0 or csi1 it will block the
+ * firmware from accessing the peripheral, and bcm2835-camera will
+ * not be able to stream data.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of_graph.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+#include <linux/videodev2.h>
+
+#include <media/v4l2-common.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-dev.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-dv-timings.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-ioctl.h>
+#include <media/v4l2-fwnode.h>
+#include <media/videobuf2-dma-contig.h>
+
+#include <media/v4l2-async.h>
+#define v4l2_async_nf_add_subdev __v4l2_async_nf_add_subdev
+
+#include "vc4-regs-unicam.h"
+
+#define UNICAM_MODULE_NAME "unicam"
+#define UNICAM_VERSION "0.1.0"
+
+static int debug;
+module_param(debug, int, 0644);
+MODULE_PARM_DESC(debug, "Debug level 0-3");
+
+#define unicam_dbg(level, dev, fmt, arg...) \
+ v4l2_dbg(level, debug, &(dev)->v4l2_dev, fmt, ##arg)
+#define unicam_info(dev, fmt, arg...) \
+ v4l2_info(&(dev)->v4l2_dev, fmt, ##arg)
+#define unicam_err(dev, fmt, arg...) \
+ v4l2_err(&(dev)->v4l2_dev, fmt, ##arg)
+
+/*
+ * Unicam must request a minimum of 250Mhz from the VPU clock.
+ * Otherwise the input FIFOs overrun and cause image corruption.
+ */
+#define MIN_VPU_CLOCK_RATE (250 * 1000 * 1000)
+/*
+ * To protect against a dodgy sensor driver never returning an error from
+ * enum_mbus_code, set a maximum index value to be used.
+ */
+#define MAX_ENUM_MBUS_CODE 128
+
+/*
+ * Stride is a 16 bit register, but also has to be a multiple of 32.
+ */
+#define BPL_ALIGNMENT 32
+#define MAX_BYTESPERLINE ((1 << 16) - BPL_ALIGNMENT)
+/*
+ * Max width is therefore determined by the max stride divided by
+ * the number of bits per pixel. Take 32bpp as a
+ * worst case.
+ * No imposed limit on the height, so adopt a square image for want
+ * of anything better.
+ */
+#define MAX_WIDTH (MAX_BYTESPERLINE / 4)
+#define MAX_HEIGHT MAX_WIDTH
+/* Define a nominal minimum image size */
+#define MIN_WIDTH 16
+#define MIN_HEIGHT 16
+/* Default size of the embedded buffer */
+#define UNICAM_EMBEDDED_SIZE 16384
+
+/*
+ * Size of the dummy buffer. Can be any size really, but the DMA
+ * allocation works in units of page sizes.
+ */
+#define DUMMY_BUF_SIZE (PAGE_SIZE)
+
+#define UNICAM_SD_PAD_SINK 0
+#define UNICAM_SD_PAD_FIRST_SOURCE 1
+#define UNICAM_SD_NUM_SOURCE_PADS 2
+#define UNICAM_SD_NUM_PADS (1 + UNICAM_SD_NUM_SOURCE_PADS)
+
+static inline bool unicam_sd_pad_is_sink(u32 pad)
+{
+ /* Camera RX has 1 sink pad, and N source pads */
+ return pad == 0;
+}
+
+static inline bool unicam_sd_pad_is_source(u32 pad)
+{
+ /* Camera RX has 1 sink pad, and N source pads */
+ return pad >= UNICAM_SD_PAD_FIRST_SOURCE &&
+ pad <= UNICAM_SD_NUM_SOURCE_PADS;
+}
+
+enum node_types {
+ IMAGE_NODE,
+ METADATA_NODE,
+ MAX_NODES
+};
+
+#define MASK_CS_DEFAULT BIT(V4L2_COLORSPACE_DEFAULT)
+#define MASK_CS_SMPTE170M BIT(V4L2_COLORSPACE_SMPTE170M)
+#define MASK_CS_SMPTE240M BIT(V4L2_COLORSPACE_SMPTE240M)
+#define MASK_CS_REC709 BIT(V4L2_COLORSPACE_REC709)
+#define MASK_CS_BT878 BIT(V4L2_COLORSPACE_BT878)
+#define MASK_CS_470_M BIT(V4L2_COLORSPACE_470_SYSTEM_M)
+#define MASK_CS_470_BG BIT(V4L2_COLORSPACE_470_SYSTEM_BG)
+#define MASK_CS_JPEG BIT(V4L2_COLORSPACE_JPEG)
+#define MASK_CS_SRGB BIT(V4L2_COLORSPACE_SRGB)
+#define MASK_CS_OPRGB BIT(V4L2_COLORSPACE_OPRGB)
+#define MASK_CS_BT2020 BIT(V4L2_COLORSPACE_BT2020)
+#define MASK_CS_RAW BIT(V4L2_COLORSPACE_RAW)
+#define MASK_CS_DCI_P3 BIT(V4L2_COLORSPACE_DCI_P3)
+
+#define MAX_COLORSPACE 32
+
+/*
+ * struct unicam_fmt - Unicam media bus format information
+ * @pixelformat: V4L2 pixel format FCC identifier. 0 if n/a.
+ * @repacked_fourcc: V4L2 pixel format FCC identifier if the data is expanded
+ * out to 16bpp. 0 if n/a.
+ * @code: V4L2 media bus format code.
+ * @depth: Bits per pixel as delivered from the source.
+ * @csi_dt: CSI data type.
+ * @valid_colorspaces: Bitmask of valid colorspaces so that the Media Controller
+ * centric try_fmt can validate the colorspace and pass
+ * v4l2-compliance.
+ * @check_variants: Flag to denote that there are multiple mediabus formats
+ * still in the list that could match this V4L2 format.
+ * @mc_skip: Media Controller shouldn't list this format via ENUM_FMT as it is
+ * a duplicate of an earlier format.
+ * @metadata_fmt: This format only applies to the metadata pad.
+ */
+struct unicam_fmt {
+ u32 fourcc;
+ u32 repacked_fourcc;
+ u32 code;
+ u8 depth;
+ u8 csi_dt;
+ u32 valid_colorspaces;
+ u8 check_variants:1;
+ u8 mc_skip:1;
+ u8 metadata_fmt:1;
+};
+
+static const struct unicam_fmt formats[] = {
+ /* YUV Formats */
+ {
+ .fourcc = V4L2_PIX_FMT_YUYV,
+ .code = MEDIA_BUS_FMT_YUYV8_2X8,
+ .depth = 16,
+ .csi_dt = 0x1e,
+ .check_variants = 1,
+ .valid_colorspaces = MASK_CS_SMPTE170M | MASK_CS_REC709 |
+ MASK_CS_JPEG,
+ }, {
+ .fourcc = V4L2_PIX_FMT_UYVY,
+ .code = MEDIA_BUS_FMT_UYVY8_2X8,
+ .depth = 16,
+ .csi_dt = 0x1e,
+ .check_variants = 1,
+ .valid_colorspaces = MASK_CS_SMPTE170M | MASK_CS_REC709 |
+ MASK_CS_JPEG,
+ }, {
+ .fourcc = V4L2_PIX_FMT_YVYU,
+ .code = MEDIA_BUS_FMT_YVYU8_2X8,
+ .depth = 16,
+ .csi_dt = 0x1e,
+ .check_variants = 1,
+ .valid_colorspaces = MASK_CS_SMPTE170M | MASK_CS_REC709 |
+ MASK_CS_JPEG,
+ }, {
+ .fourcc = V4L2_PIX_FMT_VYUY,
+ .code = MEDIA_BUS_FMT_VYUY8_2X8,
+ .depth = 16,
+ .csi_dt = 0x1e,
+ .check_variants = 1,
+ .valid_colorspaces = MASK_CS_SMPTE170M | MASK_CS_REC709 |
+ MASK_CS_JPEG,
+ }, {
+ .fourcc = V4L2_PIX_FMT_YUYV,
+ .code = MEDIA_BUS_FMT_YUYV8_1X16,
+ .depth = 16,
+ .csi_dt = 0x1e,
+ .mc_skip = 1,
+ .valid_colorspaces = MASK_CS_SMPTE170M | MASK_CS_REC709 |
+ MASK_CS_JPEG,
+ }, {
+ .fourcc = V4L2_PIX_FMT_UYVY,
+ .code = MEDIA_BUS_FMT_UYVY8_1X16,
+ .depth = 16,
+ .csi_dt = 0x1e,
+ .mc_skip = 1,
+ .valid_colorspaces = MASK_CS_SMPTE170M | MASK_CS_REC709 |
+ MASK_CS_JPEG,
+ }, {
+ .fourcc = V4L2_PIX_FMT_YVYU,
+ .code = MEDIA_BUS_FMT_YVYU8_1X16,
+ .depth = 16,
+ .csi_dt = 0x1e,
+ .mc_skip = 1,
+ .valid_colorspaces = MASK_CS_SMPTE170M | MASK_CS_REC709 |
+ MASK_CS_JPEG,
+ }, {
+ .fourcc = V4L2_PIX_FMT_VYUY,
+ .code = MEDIA_BUS_FMT_VYUY8_1X16,
+ .depth = 16,
+ .csi_dt = 0x1e,
+ .mc_skip = 1,
+ .valid_colorspaces = MASK_CS_SMPTE170M | MASK_CS_REC709 |
+ MASK_CS_JPEG,
+ }, {
+ /* RGB Formats */
+ .fourcc = V4L2_PIX_FMT_RGB565, /* gggbbbbb rrrrrggg */
+ .code = MEDIA_BUS_FMT_RGB565_2X8_LE,
+ .depth = 16,
+ .csi_dt = 0x22,
+ .valid_colorspaces = MASK_CS_SRGB,
+ }, {
+ .fourcc = V4L2_PIX_FMT_RGB565X, /* rrrrrggg gggbbbbb */
+ .code = MEDIA_BUS_FMT_RGB565_2X8_BE,
+ .depth = 16,
+ .csi_dt = 0x22,
+ .valid_colorspaces = MASK_CS_SRGB,
+ }, {
+ .fourcc = V4L2_PIX_FMT_RGB555, /* gggbbbbb arrrrrgg */
+ .code = MEDIA_BUS_FMT_RGB555_2X8_PADHI_LE,
+ .depth = 16,
+ .csi_dt = 0x21,
+ .valid_colorspaces = MASK_CS_SRGB,
+ }, {
+ .fourcc = V4L2_PIX_FMT_RGB555X, /* arrrrrgg gggbbbbb */
+ .code = MEDIA_BUS_FMT_RGB555_2X8_PADHI_BE,
+ .depth = 16,
+ .csi_dt = 0x21,
+ .valid_colorspaces = MASK_CS_SRGB,
+ }, {
+ .fourcc = V4L2_PIX_FMT_RGB24, /* rgb */
+ .code = MEDIA_BUS_FMT_RGB888_1X24,
+ .depth = 24,
+ .csi_dt = 0x24,
+ .valid_colorspaces = MASK_CS_SRGB,
+ }, {
+ .fourcc = V4L2_PIX_FMT_BGR24, /* bgr */
+ .code = MEDIA_BUS_FMT_BGR888_1X24,
+ .depth = 24,
+ .csi_dt = 0x24,
+ .valid_colorspaces = MASK_CS_SRGB,
+ }, {
+ .fourcc = V4L2_PIX_FMT_RGB32, /* argb */
+ .code = MEDIA_BUS_FMT_ARGB8888_1X32,
+ .depth = 32,
+ .csi_dt = 0x0,
+ .valid_colorspaces = MASK_CS_SRGB,
+ }, {
+ /* Bayer Formats */
+ .fourcc = V4L2_PIX_FMT_SBGGR8,
+ .code = MEDIA_BUS_FMT_SBGGR8_1X8,
+ .depth = 8,
+ .csi_dt = 0x2a,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGBRG8,
+ .code = MEDIA_BUS_FMT_SGBRG8_1X8,
+ .depth = 8,
+ .csi_dt = 0x2a,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGRBG8,
+ .code = MEDIA_BUS_FMT_SGRBG8_1X8,
+ .depth = 8,
+ .csi_dt = 0x2a,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SRGGB8,
+ .code = MEDIA_BUS_FMT_SRGGB8_1X8,
+ .depth = 8,
+ .csi_dt = 0x2a,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SBGGR10P,
+ .repacked_fourcc = V4L2_PIX_FMT_SBGGR10,
+ .code = MEDIA_BUS_FMT_SBGGR10_1X10,
+ .depth = 10,
+ .csi_dt = 0x2b,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGBRG10P,
+ .repacked_fourcc = V4L2_PIX_FMT_SGBRG10,
+ .code = MEDIA_BUS_FMT_SGBRG10_1X10,
+ .depth = 10,
+ .csi_dt = 0x2b,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGRBG10P,
+ .repacked_fourcc = V4L2_PIX_FMT_SGRBG10,
+ .code = MEDIA_BUS_FMT_SGRBG10_1X10,
+ .depth = 10,
+ .csi_dt = 0x2b,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SRGGB10P,
+ .repacked_fourcc = V4L2_PIX_FMT_SRGGB10,
+ .code = MEDIA_BUS_FMT_SRGGB10_1X10,
+ .depth = 10,
+ .csi_dt = 0x2b,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SBGGR12P,
+ .repacked_fourcc = V4L2_PIX_FMT_SBGGR12,
+ .code = MEDIA_BUS_FMT_SBGGR12_1X12,
+ .depth = 12,
+ .csi_dt = 0x2c,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGBRG12P,
+ .repacked_fourcc = V4L2_PIX_FMT_SGBRG12,
+ .code = MEDIA_BUS_FMT_SGBRG12_1X12,
+ .depth = 12,
+ .csi_dt = 0x2c,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGRBG12P,
+ .repacked_fourcc = V4L2_PIX_FMT_SGRBG12,
+ .code = MEDIA_BUS_FMT_SGRBG12_1X12,
+ .depth = 12,
+ .csi_dt = 0x2c,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SRGGB12P,
+ .repacked_fourcc = V4L2_PIX_FMT_SRGGB12,
+ .code = MEDIA_BUS_FMT_SRGGB12_1X12,
+ .depth = 12,
+ .csi_dt = 0x2c,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SBGGR14P,
+ .repacked_fourcc = V4L2_PIX_FMT_SBGGR14,
+ .code = MEDIA_BUS_FMT_SBGGR14_1X14,
+ .depth = 14,
+ .csi_dt = 0x2d,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGBRG14P,
+ .repacked_fourcc = V4L2_PIX_FMT_SGBRG14,
+ .code = MEDIA_BUS_FMT_SGBRG14_1X14,
+ .depth = 14,
+ .csi_dt = 0x2d,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SGRBG14P,
+ .repacked_fourcc = V4L2_PIX_FMT_SGRBG14,
+ .code = MEDIA_BUS_FMT_SGRBG14_1X14,
+ .depth = 14,
+ .csi_dt = 0x2d,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_SRGGB14P,
+ .repacked_fourcc = V4L2_PIX_FMT_SRGGB14,
+ .code = MEDIA_BUS_FMT_SRGGB14_1X14,
+ .depth = 14,
+ .csi_dt = 0x2d,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ /*
+ * 16 bit Bayer formats could be supported, but there is no CSI2
+ * data_type defined for raw 16, and no sensors that produce it at
+ * present.
+ */
+
+ /* Greyscale formats */
+ .fourcc = V4L2_PIX_FMT_GREY,
+ .code = MEDIA_BUS_FMT_Y8_1X8,
+ .depth = 8,
+ .csi_dt = 0x2a,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_Y10P,
+ .repacked_fourcc = V4L2_PIX_FMT_Y10,
+ .code = MEDIA_BUS_FMT_Y10_1X10,
+ .depth = 10,
+ .csi_dt = 0x2b,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_Y12P,
+ .repacked_fourcc = V4L2_PIX_FMT_Y12,
+ .code = MEDIA_BUS_FMT_Y12_1X12,
+ .depth = 12,
+ .csi_dt = 0x2c,
+ .valid_colorspaces = MASK_CS_RAW,
+ }, {
+ .fourcc = V4L2_PIX_FMT_Y14P,
+ .repacked_fourcc = V4L2_PIX_FMT_Y14,
+ .code = MEDIA_BUS_FMT_Y14_1X14,
+ .depth = 14,
+ .csi_dt = 0x2d,
+ .valid_colorspaces = MASK_CS_RAW,
+ },
+ /* Embedded data format */
+ {
+ .fourcc = V4L2_META_FMT_8,
+ .code = MEDIA_BUS_FMT_METADATA_8,
+ .depth = 8,
+ .metadata_fmt = 1,
+ }
+};
+
+struct unicam_buffer {
+ struct vb2_v4l2_buffer vb;
+ struct list_head list;
+};
+
+static inline struct unicam_buffer *to_unicam_buffer(struct vb2_buffer *vb)
+{
+ return container_of(vb, struct unicam_buffer, vb.vb2_buf);
+}
+
+struct unicam_node {
+ bool registered;
+ int open;
+ bool streaming;
+ unsigned int node_id;
+ /* Source pad id on the sensor for this node */
+ unsigned int src_pad_id;
+ /* Pointer pointing to current v4l2_buffer */
+ struct unicam_buffer *cur_frm;
+ /* Pointer pointing to next v4l2_buffer */
+ struct unicam_buffer *next_frm;
+ /* video capture */
+ const struct unicam_fmt *fmt;
+ /* Used to store current pixel format */
+ struct v4l2_format v_fmt;
+ /* Used to store current mbus frame format */
+ struct v4l2_mbus_framefmt m_fmt;
+ /* Buffer queue used in video-buf */
+ struct vb2_queue buffer_queue;
+ /* Queue of filled frames */
+ struct list_head dma_queue;
+ /* IRQ lock for DMA queue */
+ spinlock_t dma_queue_lock;
+ /* lock used to access this structure */
+ struct mutex lock;
+ /* Identifies video device for this channel */
+ struct video_device video_dev;
+ /* Pointer to the parent handle */
+ struct unicam_device *dev;
+ struct media_pad pad;
+ unsigned int embedded_lines;
+ struct media_pipeline pipe;
+ /*
+ * Dummy buffer intended to be used by unicam
+ * if we have no other queued buffers to swap to.
+ */
+ void *dummy_buf_cpu_addr;
+ dma_addr_t dummy_buf_dma_addr;
+};
+
+struct unicam_device {
+ struct kref kref;
+
+ /* V4l2 specific parameters */
+ struct v4l2_async_subdev asd;
+
+ /* peripheral base address */
+ void __iomem *base;
+ /* clock gating base address */
+ void __iomem *clk_gate_base;
+ /* lp clock handle */
+ struct clk *clock;
+ /* vpu clock handle */
+ struct clk *vpu_clock;
+ /* vpu clock request */
+ struct clk_request *vpu_req;
+ /* clock status for error handling */
+ bool clocks_enabled;
+ /* V4l2 device */
+ struct v4l2_device v4l2_dev;
+ struct media_device mdev;
+
+ /* parent device */
+ struct platform_device *pdev;
+ /* subdevice async Notifier */
+ struct v4l2_async_notifier notifier;
+ unsigned int sequence;
+
+ /* ptr to sub device */
+ struct v4l2_subdev *sensor;
+ /* Pad config for the sensor */
+ struct v4l2_subdev_state *sensor_state;
+
+ /* Internal subdev */
+ struct v4l2_subdev sd;
+ struct media_pad pads[UNICAM_SD_NUM_PADS];
+
+ bool streaming;
+
+ enum v4l2_mbus_type bus_type;
+ /*
+ * Stores bus.mipi_csi2.flags for CSI2 sensors, or
+ * bus.mipi_csi1.strobe for CCP2.
+ */
+ unsigned int bus_flags;
+ unsigned int max_data_lanes;
+ unsigned int active_data_lanes;
+ bool sensor_embedded_data;
+
+ struct unicam_node node[MAX_NODES];
+ struct v4l2_ctrl_handler ctrl_handler;
+
+ bool mc_api;
+};
+
+static inline struct unicam_device *
+to_unicam_device(struct v4l2_device *v4l2_dev)
+{
+ return container_of(v4l2_dev, struct unicam_device, v4l2_dev);
+}
+
+static inline struct unicam_device *
+sd_to_unicam_device(struct v4l2_subdev *sd)
+{
+ return container_of(sd, struct unicam_device, sd);
+}
+
+static inline bool is_metadata_node(struct unicam_node *node)
+{
+ return node->video_dev.device_caps & V4L2_CAP_META_CAPTURE;
+}
+
+static inline bool is_image_node(struct unicam_node *node)
+{
+ return node->video_dev.device_caps & V4L2_CAP_VIDEO_CAPTURE;
+}
+
+/* Hardware access */
+static inline void clk_write(struct unicam_device *dev, u32 val)
+{
+ writel(val | 0x5a000000, dev->clk_gate_base);
+}
+
+static inline u32 reg_read(struct unicam_device *dev, u32 offset)
+{
+ return readl(dev->base + offset);
+}
+
+static inline void reg_write(struct unicam_device *dev, u32 offset, u32 val)
+{
+ writel(val, dev->base + offset);
+}
+
+static inline int get_field(u32 value, u32 mask)
+{
+ return (value & mask) >> __ffs(mask);
+}
+
+static inline void set_field(u32 *valp, u32 field, u32 mask)
+{
+ u32 val = *valp;
+
+ val &= ~mask;
+ val |= (field << __ffs(mask)) & mask;
+ *valp = val;
+}
+
+static inline u32 reg_read_field(struct unicam_device *dev, u32 offset,
+ u32 mask)
+{
+ return get_field(reg_read(dev, offset), mask);
+}
+
+static inline void reg_write_field(struct unicam_device *dev, u32 offset,
+ u32 field, u32 mask)
+{
+ u32 val = reg_read(dev, offset);
+
+ set_field(&val, field, mask);
+ reg_write(dev, offset, val);
+}
+
+/* Power management functions */
+static inline int unicam_runtime_get(struct unicam_device *dev)
+{
+ return pm_runtime_get_sync(&dev->pdev->dev);
+}
+
+static inline void unicam_runtime_put(struct unicam_device *dev)
+{
+ pm_runtime_put_sync(&dev->pdev->dev);
+}
+
+/* Format setup functions */
+static const struct unicam_fmt *find_format_by_code(u32 code)
+{
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(formats); i++) {
+ if (formats[i].code == code)
+ return &formats[i];
+ }
+
+ return NULL;
+}
+
+static const struct unicam_fmt *find_format_by_fourcc(u32 fourcc)
+{
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(formats); ++i) {
+ if (formats[i].fourcc == fourcc)
+ return &formats[i];
+ }
+
+ return NULL;
+}
+
+static unsigned int bytes_per_line(u32 width, const struct unicam_fmt *fmt,
+ u32 v4l2_fourcc)
+{
+ if (v4l2_fourcc == fmt->repacked_fourcc)
+ /* Repacking always goes to 16bpp */
+ return ALIGN(width << 1, BPL_ALIGNMENT);
+ else
+ return ALIGN((width * fmt->depth) >> 3, BPL_ALIGNMENT);
+}
+
+static int unicam_calc_format_size_bpl(struct unicam_device *dev,
+ const struct unicam_fmt *fmt,
+ struct v4l2_format *f)
+{
+ unsigned int min_bytesperline;
+
+ v4l_bound_align_image(&f->fmt.pix.width, MIN_WIDTH, MAX_WIDTH, 2,
+ &f->fmt.pix.height, MIN_HEIGHT, MAX_HEIGHT, 0,
+ 0);
+
+ min_bytesperline = bytes_per_line(f->fmt.pix.width, fmt,
+ f->fmt.pix.pixelformat);
+
+ if (f->fmt.pix.bytesperline > min_bytesperline &&
+ f->fmt.pix.bytesperline <= MAX_BYTESPERLINE)
+ f->fmt.pix.bytesperline = ALIGN(f->fmt.pix.bytesperline,
+ BPL_ALIGNMENT);
+ else
+ f->fmt.pix.bytesperline = min_bytesperline;
+
+ f->fmt.pix.sizeimage = f->fmt.pix.height * f->fmt.pix.bytesperline;
+
+ unicam_dbg(3, dev, "%s: fourcc: %08X size: %dx%d bpl:%d img_size:%d\n",
+ __func__,
+ f->fmt.pix.pixelformat,
+ f->fmt.pix.width, f->fmt.pix.height,
+ f->fmt.pix.bytesperline, f->fmt.pix.sizeimage);
+
+ return 0;
+}
+
+static void unicam_wr_dma_addr(struct unicam_device *dev, dma_addr_t dmaaddr,
+ unsigned int buffer_size, int node_id)
+{
+ dma_addr_t endaddr = dmaaddr + buffer_size;
+
+ if (node_id == IMAGE_NODE) {
+ reg_write(dev, UNICAM_IBSA0, dmaaddr);
+ reg_write(dev, UNICAM_IBEA0, endaddr);
+ } else {
+ reg_write(dev, UNICAM_DBSA0, dmaaddr);
+ reg_write(dev, UNICAM_DBEA0, endaddr);
+ }
+}
+
+static unsigned int unicam_get_lines_done(struct unicam_device *dev)
+{
+ dma_addr_t start_addr, cur_addr;
+ unsigned int stride = dev->node[IMAGE_NODE].v_fmt.fmt.pix.bytesperline;
+ struct unicam_buffer *frm = dev->node[IMAGE_NODE].cur_frm;
+
+ if (!frm)
+ return 0;
+
+ start_addr = vb2_dma_contig_plane_dma_addr(&frm->vb.vb2_buf, 0);
+ cur_addr = reg_read(dev, UNICAM_IBWP);
+ return (unsigned int)(cur_addr - start_addr) / stride;
+}
+
+static void unicam_schedule_next_buffer(struct unicam_node *node)
+{
+ struct unicam_device *dev = node->dev;
+ struct unicam_buffer *buf;
+ unsigned int size;
+ dma_addr_t addr;
+
+ buf = list_first_entry(&node->dma_queue, struct unicam_buffer, list);
+ node->next_frm = buf;
+ list_del(&buf->list);
+
+ addr = vb2_dma_contig_plane_dma_addr(&buf->vb.vb2_buf, 0);
+ if (is_image_node(node)) {
+ size = node->v_fmt.fmt.pix.sizeimage;
+ unicam_wr_dma_addr(dev, addr, size, IMAGE_NODE);
+ } else {
+ size = node->v_fmt.fmt.meta.buffersize;
+ unicam_wr_dma_addr(dev, addr, size, METADATA_NODE);
+ }
+}
+
+static void unicam_schedule_dummy_buffer(struct unicam_node *node)
+{
+ struct unicam_device *dev = node->dev;
+ int node_id = is_image_node(node) ? IMAGE_NODE : METADATA_NODE;
+
+ unicam_dbg(3, dev, "Scheduling dummy buffer for node %d\n", node_id);
+
+ unicam_wr_dma_addr(dev, node->dummy_buf_dma_addr, DUMMY_BUF_SIZE,
+ node_id);
+ node->next_frm = NULL;
+}
+
+static void unicam_process_buffer_complete(struct unicam_node *node,
+ unsigned int sequence)
+{
+ node->cur_frm->vb.field = node->m_fmt.field;
+ node->cur_frm->vb.sequence = sequence;
+
+ vb2_buffer_done(&node->cur_frm->vb.vb2_buf, VB2_BUF_STATE_DONE);
+}
+
+static void unicam_queue_event_sof(struct unicam_device *unicam)
+{
+ struct v4l2_event event = {
+ .type = V4L2_EVENT_FRAME_SYNC,
+ .u.frame_sync.frame_sequence = unicam->sequence,
+ };
+
+ v4l2_event_queue(&unicam->node[IMAGE_NODE].video_dev, &event);
+}
+
+/*
+ * unicam_isr : ISR handler for unicam capture
+ * @irq: irq number
+ * @dev_id: dev_id ptr
+ *
+ * It changes status of the captured buffer, takes next buffer from the queue
+ * and sets its address in unicam registers
+ */
+static irqreturn_t unicam_isr(int irq, void *dev)
+{
+ struct unicam_device *unicam = dev;
+ unsigned int lines_done = unicam_get_lines_done(dev);
+ unsigned int sequence = unicam->sequence;
+ unsigned int i;
+ u32 ista, sta;
+ bool fe;
+ u64 ts;
+
+ sta = reg_read(unicam, UNICAM_STA);
+ /* Write value back to clear the interrupts */
+ reg_write(unicam, UNICAM_STA, sta);
+
+ ista = reg_read(unicam, UNICAM_ISTA);
+ /* Write value back to clear the interrupts */
+ reg_write(unicam, UNICAM_ISTA, ista);
+
+ unicam_dbg(3, unicam, "ISR: ISTA: 0x%X, STA: 0x%X, sequence %d, lines done %d",
+ ista, sta, sequence, lines_done);
+
+ if (!(sta & (UNICAM_IS | UNICAM_PI0)))
+ return IRQ_HANDLED;
+
+ /*
+ * Look for either the Frame End interrupt or the Packet Capture status
+ * to signal a frame end.
+ */
+ fe = (ista & UNICAM_FEI || sta & UNICAM_PI0);
+
+ /*
+ * We must run the frame end handler first. If we have a valid next_frm
+ * and we get a simultaneout FE + FS interrupt, running the FS handler
+ * first would null out the next_frm ptr and we would have lost the
+ * buffer forever.
+ */
+ if (fe) {
+ /*
+ * Ensure we have swapped buffers already as we can't
+ * stop the peripheral. If no buffer is available, use a
+ * dummy buffer to dump out frames until we get a new buffer
+ * to use.
+ */
+ for (i = 0; i < ARRAY_SIZE(unicam->node); i++) {
+ if (!unicam->node[i].streaming)
+ continue;
+
+ /*
+ * If cur_frm == next_frm, it means we have not had
+ * a chance to swap buffers, likely due to having
+ * multiple interrupts occurring simultaneously (like FE
+ * + FS + LS). In this case, we cannot signal the buffer
+ * as complete, as the HW will reuse that buffer.
+ */
+ if (unicam->node[i].cur_frm &&
+ unicam->node[i].cur_frm != unicam->node[i].next_frm)
+ unicam_process_buffer_complete(&unicam->node[i],
+ sequence);
+ unicam->node[i].cur_frm = unicam->node[i].next_frm;
+ }
+ unicam->sequence++;
+ }
+
+ if (ista & UNICAM_FSI) {
+ /*
+ * Timestamp is to be when the first data byte was captured,
+ * aka frame start.
+ */
+ ts = ktime_get_ns();
+ for (i = 0; i < ARRAY_SIZE(unicam->node); i++) {
+ if (!unicam->node[i].streaming)
+ continue;
+
+ if (unicam->node[i].cur_frm)
+ unicam->node[i].cur_frm->vb.vb2_buf.timestamp =
+ ts;
+ else
+ unicam_dbg(2, unicam, "ISR: [%d] Dropping frame, buffer not available at FS\n",
+ i);
+ /*
+ * Set the next frame output to go to a dummy frame
+ * if we have not managed to obtain another frame
+ * from the queue.
+ */
+ unicam_schedule_dummy_buffer(&unicam->node[i]);
+ }
+
+ unicam_queue_event_sof(unicam);
+ }
+
+ /*
+ * Cannot swap buffer at frame end, there may be a race condition
+ * where the HW does not actually swap it if the new frame has
+ * already started.
+ */
+ if (ista & (UNICAM_FSI | UNICAM_LCI) && !fe) {
+ for (i = 0; i < ARRAY_SIZE(unicam->node); i++) {
+ if (!unicam->node[i].streaming)
+ continue;
+
+ spin_lock(&unicam->node[i].dma_queue_lock);
+ if (!list_empty(&unicam->node[i].dma_queue) &&
+ !unicam->node[i].next_frm)
+ unicam_schedule_next_buffer(&unicam->node[i]);
+ spin_unlock(&unicam->node[i].dma_queue_lock);
+ }
+ }
+
+ if (reg_read(unicam, UNICAM_ICTL) & UNICAM_FCM) {
+ /* Switch out of trigger mode if selected */
+ reg_write_field(unicam, UNICAM_ICTL, 1, UNICAM_TFC);
+ reg_write_field(unicam, UNICAM_ICTL, 0, UNICAM_FCM);
+ }
+ return IRQ_HANDLED;
+}
+
+/* V4L2 Common IOCTLs */
+static int unicam_querycap(struct file *file, void *priv,
+ struct v4l2_capability *cap)
+{
+ struct unicam_node *node = video_drvdata(file);
+ struct unicam_device *dev = node->dev;
+
+ strscpy(cap->driver, UNICAM_MODULE_NAME, sizeof(cap->driver));
+ strscpy(cap->card, UNICAM_MODULE_NAME, sizeof(cap->card));
+
+ snprintf(cap->bus_info, sizeof(cap->bus_info),
+ "platform:%s", dev_name(&dev->pdev->dev));
+
+ cap->capabilities |= V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_META_CAPTURE;
+
+ return 0;
+}
+
+static int unicam_log_status(struct file *file, void *fh)
+{
+ struct unicam_node *node = video_drvdata(file);
+ struct unicam_device *dev = node->dev;
+ u32 reg;
+
+ /* status for sub devices */
+ v4l2_device_call_all(&dev->v4l2_dev, 0, core, log_status);
+
+ unicam_info(dev, "-----Receiver status-----\n");
+ unicam_info(dev, "V4L2 width/height: %ux%u\n",
+ node->v_fmt.fmt.pix.width, node->v_fmt.fmt.pix.height);
+ unicam_info(dev, "Mediabus format: %08x\n", node->fmt->code);
+ unicam_info(dev, "V4L2 format: %08x\n",
+ node->v_fmt.fmt.pix.pixelformat);
+ reg = reg_read(dev, UNICAM_IPIPE);
+ unicam_info(dev, "Unpacking/packing: %u / %u\n",
+ get_field(reg, UNICAM_PUM_MASK),
+ get_field(reg, UNICAM_PPM_MASK));
+ unicam_info(dev, "----Live data----\n");
+ unicam_info(dev, "Programmed stride: %4u\n",
+ reg_read(dev, UNICAM_IBLS));
+ unicam_info(dev, "Detected resolution: %ux%u\n",
+ reg_read(dev, UNICAM_IHSTA),
+ reg_read(dev, UNICAM_IVSTA));
+ unicam_info(dev, "Write pointer: %08x\n",
+ reg_read(dev, UNICAM_IBWP));
+
+ return 0;
+}
+
+static int unicam_subscribe_event(struct v4l2_fh *fh,
+ const struct v4l2_event_subscription *sub)
+{
+ switch (sub->type) {
+ case V4L2_EVENT_FRAME_SYNC:
+ return v4l2_event_subscribe(fh, sub, 2, NULL);
+ case V4L2_EVENT_SOURCE_CHANGE:
+ return v4l2_event_subscribe(fh, sub, 4, NULL);
+ }
+
+ return v4l2_ctrl_subscribe_event(fh, sub);
+}
+
+static void unicam_notify(struct v4l2_subdev *sd,
+ unsigned int notification, void *arg)
+{
+ struct unicam_device *dev = to_unicam_device(sd->v4l2_dev);
+
+ switch (notification) {
+ case V4L2_DEVICE_NOTIFY_EVENT:
+ v4l2_event_queue(&dev->node[IMAGE_NODE].video_dev, arg);
+ break;
+ default:
+ break;
+ }
+}
+
+/* V4L2 Media Controller Centric IOCTLs */
+
+static int unicam_mc_enum_fmt_vid_cap(struct file *file, void *priv,
+ struct v4l2_fmtdesc *f)
+{
+ int i, j;
+
+ for (i = 0, j = 0; i < ARRAY_SIZE(formats); i++) {
+ if (f->mbus_code && formats[i].code != f->mbus_code)
+ continue;
+ if (formats[i].mc_skip || formats[i].metadata_fmt)
+ continue;
+
+ if (formats[i].fourcc) {
+ if (j == f->index) {
+ f->pixelformat = formats[i].fourcc;
+ f->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
+ return 0;
+ }
+ j++;
+ }
+ if (formats[i].repacked_fourcc) {
+ if (j == f->index) {
+ f->pixelformat = formats[i].repacked_fourcc;
+ f->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
+ return 0;
+ }
+ j++;
+ }
+ }
+
+ return -EINVAL;
+}
+
+static int unicam_mc_g_fmt_vid_cap(struct file *file, void *priv,
+ struct v4l2_format *f)
+{
+ struct unicam_node *node = video_drvdata(file);
+
+ if (!is_image_node(node))
+ return -EINVAL;
+
+ *f = node->v_fmt;
+
+ return 0;
+}
+
+static void unicam_mc_try_fmt(struct unicam_node *node, struct v4l2_format *f,
+ const struct unicam_fmt **ret_fmt)
+{
+ struct v4l2_pix_format *v4l2_format = &f->fmt.pix;
+ struct unicam_device *dev = node->dev;
+ const struct unicam_fmt *fmt;
+ int is_rgb;
+
+ /*
+ * Default to the first format if the requested pixel format code isn't
+ * supported.
+ */
+ fmt = find_format_by_fourcc(v4l2_format->pixelformat);
+ if (!fmt) {
+ fmt = &formats[0];
+ v4l2_format->pixelformat = fmt->fourcc;
+ }
+
+ unicam_calc_format_size_bpl(dev, fmt, f);
+
+ if (v4l2_format->field == V4L2_FIELD_ANY)
+ v4l2_format->field = V4L2_FIELD_NONE;
+
+ if (v4l2_format->colorspace >= MAX_COLORSPACE ||
+ !(fmt->valid_colorspaces & (1 << v4l2_format->colorspace))) {
+ v4l2_format->colorspace = __ffs(fmt->valid_colorspaces);
+
+ v4l2_format->xfer_func =
+ V4L2_MAP_XFER_FUNC_DEFAULT(v4l2_format->colorspace);
+ v4l2_format->ycbcr_enc =
+ V4L2_MAP_YCBCR_ENC_DEFAULT(v4l2_format->colorspace);
+ is_rgb = v4l2_format->colorspace == V4L2_COLORSPACE_SRGB;
+ v4l2_format->quantization =
+ V4L2_MAP_QUANTIZATION_DEFAULT(is_rgb,
+ v4l2_format->colorspace,
+ v4l2_format->ycbcr_enc);
+ }
+
+ if (ret_fmt)
+ *ret_fmt = fmt;
+
+ unicam_dbg(3, dev, "%s: %08x %ux%u (bytesperline %u sizeimage %u)\n",
+ __func__, v4l2_format->pixelformat,
+ v4l2_format->width, v4l2_format->height,
+ v4l2_format->bytesperline, v4l2_format->sizeimage);
+}
+
+static int unicam_mc_try_fmt_vid_cap(struct file *file, void *priv,
+ struct v4l2_format *f)
+{
+ struct unicam_node *node = video_drvdata(file);
+
+ unicam_mc_try_fmt(node, f, NULL);
+ return 0;
+}
+
+static int unicam_mc_s_fmt_vid_cap(struct file *file, void *priv,
+ struct v4l2_format *f)
+{
+ struct unicam_node *node = video_drvdata(file);
+ struct unicam_device *dev = node->dev;
+ const struct unicam_fmt *fmt;
+
+ if (vb2_is_busy(&node->buffer_queue)) {
+ unicam_dbg(3, dev, "%s device busy\n", __func__);
+ return -EBUSY;
+ }
+
+ unicam_mc_try_fmt(node, f, &fmt);
+
+ node->v_fmt = *f;
+ node->fmt = fmt;
+
+ return 0;
+}
+
+static int unicam_mc_enum_framesizes(struct file *file, void *fh,
+ struct v4l2_frmsizeenum *fsize)
+{
+ struct unicam_node *node = video_drvdata(file);
+ struct unicam_device *dev = node->dev;
+
+ if (fsize->index > 0)
+ return -EINVAL;
+
+ if (!find_format_by_fourcc(fsize->pixel_format)) {
+ unicam_dbg(3, dev, "Invalid pixel format 0x%08x\n",
+ fsize->pixel_format);
+ return -EINVAL;
+ }
+
+ fsize->type = V4L2_FRMSIZE_TYPE_STEPWISE;
+ fsize->stepwise.min_width = MIN_WIDTH;
+ fsize->stepwise.max_width = MAX_WIDTH;
+ fsize->stepwise.step_width = 1;
+ fsize->stepwise.min_height = MIN_HEIGHT;
+ fsize->stepwise.max_height = MAX_HEIGHT;
+ fsize->stepwise.step_height = 1;
+
+ return 0;
+}
+
+static int unicam_mc_enum_fmt_meta_cap(struct file *file, void *priv,
+ struct v4l2_fmtdesc *f)
+{
+ struct unicam_node *node = video_drvdata(file);
+ int i, j;
+
+ if (!is_metadata_node(node))
+ return -EINVAL;
+
+ for (i = 0, j = 0; i < ARRAY_SIZE(formats); i++) {
+ if (f->mbus_code && formats[i].code != f->mbus_code)
+ continue;
+ if (!formats[i].metadata_fmt)
+ continue;
+
+ if (formats[i].fourcc) {
+ if (j == f->index) {
+ f->pixelformat = formats[i].fourcc;
+ f->type = V4L2_BUF_TYPE_META_CAPTURE;
+ return 0;
+ }
+ j++;
+ }
+ }
+
+ return -EINVAL;
+}
+
+static int unicam_mc_g_fmt_meta_cap(struct file *file, void *priv,
+ struct v4l2_format *f)
+{
+ struct unicam_node *node = video_drvdata(file);
+
+ if (!is_metadata_node(node))
+ return -EINVAL;
+
+ *f = node->v_fmt;
+
+ return 0;
+}
+
+static int unicam_mc_try_fmt_meta_cap(struct file *file, void *priv,
+ struct v4l2_format *f)
+{
+ struct unicam_node *node = video_drvdata(file);
+
+ if (!is_metadata_node(node))
+ return -EINVAL;
+
+ f->fmt.meta.dataformat = V4L2_META_FMT_8;
+
+ return 0;
+}
+
+static int unicam_mc_s_fmt_meta_cap(struct file *file, void *priv,
+ struct v4l2_format *f)
+{
+ struct unicam_node *node = video_drvdata(file);
+
+ if (!is_metadata_node(node))
+ return -EINVAL;
+
+ unicam_mc_try_fmt_meta_cap(file, priv, f);
+
+ node->v_fmt = *f;
+
+ return 0;
+}
+
+static const struct v4l2_ioctl_ops unicam_mc_ioctl_ops = {
+ .vidioc_querycap = unicam_querycap,
+ .vidioc_enum_fmt_vid_cap = unicam_mc_enum_fmt_vid_cap,
+ .vidioc_g_fmt_vid_cap = unicam_mc_g_fmt_vid_cap,
+ .vidioc_try_fmt_vid_cap = unicam_mc_try_fmt_vid_cap,
+ .vidioc_s_fmt_vid_cap = unicam_mc_s_fmt_vid_cap,
+
+ .vidioc_enum_fmt_meta_cap = unicam_mc_enum_fmt_meta_cap,
+ .vidioc_g_fmt_meta_cap = unicam_mc_g_fmt_meta_cap,
+ .vidioc_try_fmt_meta_cap = unicam_mc_try_fmt_meta_cap,
+ .vidioc_s_fmt_meta_cap = unicam_mc_s_fmt_meta_cap,
+
+ .vidioc_enum_framesizes = unicam_mc_enum_framesizes,
+ .vidioc_reqbufs = vb2_ioctl_reqbufs,
+ .vidioc_create_bufs = vb2_ioctl_create_bufs,
+ .vidioc_prepare_buf = vb2_ioctl_prepare_buf,
+ .vidioc_querybuf = vb2_ioctl_querybuf,
+ .vidioc_qbuf = vb2_ioctl_qbuf,
+ .vidioc_dqbuf = vb2_ioctl_dqbuf,
+ .vidioc_expbuf = vb2_ioctl_expbuf,
+ .vidioc_streamon = vb2_ioctl_streamon,
+ .vidioc_streamoff = vb2_ioctl_streamoff,
+
+ .vidioc_log_status = unicam_log_status,
+ .vidioc_subscribe_event = unicam_subscribe_event,
+ .vidioc_unsubscribe_event = v4l2_event_unsubscribe,
+};
+
+static const struct media_entity_operations unicam_mc_entity_ops = {
+ .link_validate = v4l2_subdev_link_validate,
+ .has_route = v4l2_subdev_has_route,
+};
+
+/* videobuf2 Operations */
+
+static int unicam_queue_setup(struct vb2_queue *vq,
+ unsigned int *nbuffers,
+ unsigned int *nplanes,
+ unsigned int sizes[],
+ struct device *alloc_devs[])
+{
+ struct unicam_node *node = vb2_get_drv_priv(vq);
+ struct unicam_device *dev = node->dev;
+ unsigned int size = is_image_node(node) ?
+ node->v_fmt.fmt.pix.sizeimage :
+ node->v_fmt.fmt.meta.buffersize;
+
+ if (vq->num_buffers + *nbuffers < 3)
+ *nbuffers = 3 - vq->num_buffers;
+
+ if (*nplanes) {
+ if (sizes[0] < size) {
+ unicam_err(dev, "sizes[0] %i < size %u\n", sizes[0],
+ size);
+ return -EINVAL;
+ }
+ size = sizes[0];
+ }
+
+ *nplanes = 1;
+ sizes[0] = size;
+
+ return 0;
+}
+
+static int unicam_buffer_prepare(struct vb2_buffer *vb)
+{
+ struct unicam_node *node = vb2_get_drv_priv(vb->vb2_queue);
+ struct unicam_device *dev = node->dev;
+ struct unicam_buffer *buf = to_unicam_buffer(vb);
+ unsigned long size;
+
+ if (WARN_ON(!node->fmt))
+ return -EINVAL;
+
+ size = is_image_node(node) ? node->v_fmt.fmt.pix.sizeimage :
+ node->v_fmt.fmt.meta.buffersize;
+ if (vb2_plane_size(vb, 0) < size) {
+ unicam_err(dev, "data will not fit into plane (%lu < %lu)\n",
+ vb2_plane_size(vb, 0), size);
+ return -EINVAL;
+ }
+
+ vb2_set_plane_payload(&buf->vb.vb2_buf, 0, size);
+ return 0;
+}
+
+static void unicam_buffer_queue(struct vb2_buffer *vb)
+{
+ struct unicam_node *node = vb2_get_drv_priv(vb->vb2_queue);
+ struct unicam_buffer *buf = to_unicam_buffer(vb);
+ unsigned long flags;
+
+ spin_lock_irqsave(&node->dma_queue_lock, flags);
+ list_add_tail(&buf->list, &node->dma_queue);
+ spin_unlock_irqrestore(&node->dma_queue_lock, flags);
+}
+
+static void unicam_set_packing_config(struct unicam_device *dev)
+{
+ u32 pack, unpack;
+ u32 val;
+
+ if (dev->node[IMAGE_NODE].v_fmt.fmt.pix.pixelformat ==
+ dev->node[IMAGE_NODE].fmt->fourcc) {
+ unpack = UNICAM_PUM_NONE;
+ pack = UNICAM_PPM_NONE;
+ } else {
+ switch (dev->node[IMAGE_NODE].fmt->depth) {
+ case 8:
+ unpack = UNICAM_PUM_UNPACK8;
+ break;
+ case 10:
+ unpack = UNICAM_PUM_UNPACK10;
+ break;
+ case 12:
+ unpack = UNICAM_PUM_UNPACK12;
+ break;
+ case 14:
+ unpack = UNICAM_PUM_UNPACK14;
+ break;
+ case 16:
+ unpack = UNICAM_PUM_UNPACK16;
+ break;
+ default:
+ unpack = UNICAM_PUM_NONE;
+ break;
+ }
+
+ /* Repacking is always to 16bpp */
+ pack = UNICAM_PPM_PACK16;
+ }
+
+ val = 0;
+ set_field(&val, unpack, UNICAM_PUM_MASK);
+ set_field(&val, pack, UNICAM_PPM_MASK);
+ reg_write(dev, UNICAM_IPIPE, val);
+}
+
+static void unicam_cfg_image_id(struct unicam_device *dev)
+{
+ if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) {
+ /* CSI2 mode, hardcode VC 0 for now. */
+ reg_write(dev, UNICAM_IDI0,
+ (0 << 6) | dev->node[IMAGE_NODE].fmt->csi_dt);
+ } else {
+ /* CCP2 mode */
+ reg_write(dev, UNICAM_IDI0,
+ 0x80 | dev->node[IMAGE_NODE].fmt->csi_dt);
+ }
+}
+
+static void unicam_enable_ed(struct unicam_device *dev)
+{
+ u32 val = reg_read(dev, UNICAM_DCS);
+
+ set_field(&val, 2, UNICAM_EDL_MASK);
+ /* Do not wrap at the end of the embedded data buffer */
+ set_field(&val, 0, UNICAM_DBOB);
+
+ reg_write(dev, UNICAM_DCS, val);
+}
+
+static void unicam_start_rx(struct unicam_device *dev, dma_addr_t *addr)
+{
+ int line_int_freq = dev->node[IMAGE_NODE].v_fmt.fmt.pix.height >> 2;
+ unsigned int size, i;
+ u32 val;
+
+ if (line_int_freq < 128)
+ line_int_freq = 128;
+
+ /* Enable lane clocks */
+ val = 1;
+ for (i = 0; i < dev->active_data_lanes; i++)
+ val = val << 2 | 1;
+ clk_write(dev, val);
+
+ /* Basic init */
+ reg_write(dev, UNICAM_CTRL, UNICAM_MEM);
+
+ /* Enable analogue control, and leave in reset. */
+ val = UNICAM_AR;
+ set_field(&val, 7, UNICAM_CTATADJ_MASK);
+ set_field(&val, 7, UNICAM_PTATADJ_MASK);
+ reg_write(dev, UNICAM_ANA, val);
+ usleep_range(1000, 2000);
+
+ /* Come out of reset */
+ reg_write_field(dev, UNICAM_ANA, 0, UNICAM_AR);
+
+ /* Peripheral reset */
+ reg_write_field(dev, UNICAM_CTRL, 1, UNICAM_CPR);
+ reg_write_field(dev, UNICAM_CTRL, 0, UNICAM_CPR);
+
+ reg_write_field(dev, UNICAM_CTRL, 0, UNICAM_CPE);
+
+ /* Enable Rx control. */
+ val = reg_read(dev, UNICAM_CTRL);
+ if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) {
+ set_field(&val, UNICAM_CPM_CSI2, UNICAM_CPM_MASK);
+ set_field(&val, UNICAM_DCM_STROBE, UNICAM_DCM_MASK);
+ } else {
+ set_field(&val, UNICAM_CPM_CCP2, UNICAM_CPM_MASK);
+ set_field(&val, dev->bus_flags, UNICAM_DCM_MASK);
+ }
+ /* Packet framer timeout */
+ set_field(&val, 0xf, UNICAM_PFT_MASK);
+ set_field(&val, 128, UNICAM_OET_MASK);
+ reg_write(dev, UNICAM_CTRL, val);
+
+ reg_write(dev, UNICAM_IHWIN, 0);
+ reg_write(dev, UNICAM_IVWIN, 0);
+
+ /* AXI bus access QoS setup */
+ val = reg_read(dev, UNICAM_PRI);
+ set_field(&val, 0, UNICAM_BL_MASK);
+ set_field(&val, 0, UNICAM_BS_MASK);
+ set_field(&val, 0xe, UNICAM_PP_MASK);
+ set_field(&val, 8, UNICAM_NP_MASK);
+ set_field(&val, 2, UNICAM_PT_MASK);
+ set_field(&val, 1, UNICAM_PE);
+ reg_write(dev, UNICAM_PRI, val);
+
+ reg_write_field(dev, UNICAM_ANA, 0, UNICAM_DDL);
+
+ /* Always start in trigger frame capture mode (UNICAM_FCM set) */
+ val = UNICAM_FSIE | UNICAM_FEIE | UNICAM_FCM | UNICAM_IBOB;
+ set_field(&val, line_int_freq, UNICAM_LCIE_MASK);
+ reg_write(dev, UNICAM_ICTL, val);
+ reg_write(dev, UNICAM_STA, UNICAM_STA_MASK_ALL);
+ reg_write(dev, UNICAM_ISTA, UNICAM_ISTA_MASK_ALL);
+
+ /* tclk_term_en */
+ reg_write_field(dev, UNICAM_CLT, 2, UNICAM_CLT1_MASK);
+ /* tclk_settle */
+ reg_write_field(dev, UNICAM_CLT, 6, UNICAM_CLT2_MASK);
+ /* td_term_en */
+ reg_write_field(dev, UNICAM_DLT, 2, UNICAM_DLT1_MASK);
+ /* ths_settle */
+ reg_write_field(dev, UNICAM_DLT, 6, UNICAM_DLT2_MASK);
+ /* trx_enable */
+ reg_write_field(dev, UNICAM_DLT, 0, UNICAM_DLT3_MASK);
+
+ reg_write_field(dev, UNICAM_CTRL, 0, UNICAM_SOE);
+
+ /* Packet compare setup - required to avoid missing frame ends */
+ val = 0;
+ set_field(&val, 1, UNICAM_PCE);
+ set_field(&val, 1, UNICAM_GI);
+ set_field(&val, 1, UNICAM_CPH);
+ set_field(&val, 0, UNICAM_PCVC_MASK);
+ set_field(&val, 1, UNICAM_PCDT_MASK);
+ reg_write(dev, UNICAM_CMP0, val);
+
+ /* Enable clock lane and set up terminations */
+ val = 0;
+ if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) {
+ /* CSI2 */
+ set_field(&val, 1, UNICAM_CLE);
+ set_field(&val, 1, UNICAM_CLLPE);
+ if (dev->bus_flags & V4L2_MBUS_CSI2_CONTINUOUS_CLOCK) {
+ set_field(&val, 1, UNICAM_CLTRE);
+ set_field(&val, 1, UNICAM_CLHSE);
+ }
+ } else {
+ /* CCP2 */
+ set_field(&val, 1, UNICAM_CLE);
+ set_field(&val, 1, UNICAM_CLHSE);
+ set_field(&val, 1, UNICAM_CLTRE);
+ }
+ reg_write(dev, UNICAM_CLK, val);
+
+ /*
+ * Enable required data lanes with appropriate terminations.
+ * The same value needs to be written to UNICAM_DATn registers for
+ * the active lanes, and 0 for inactive ones.
+ */
+ val = 0;
+ if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) {
+ /* CSI2 */
+ set_field(&val, 1, UNICAM_DLE);
+ set_field(&val, 1, UNICAM_DLLPE);
+ if (dev->bus_flags & V4L2_MBUS_CSI2_CONTINUOUS_CLOCK) {
+ set_field(&val, 1, UNICAM_DLTRE);
+ set_field(&val, 1, UNICAM_DLHSE);
+ }
+ } else {
+ /* CCP2 */
+ set_field(&val, 1, UNICAM_DLE);
+ set_field(&val, 1, UNICAM_DLHSE);
+ set_field(&val, 1, UNICAM_DLTRE);
+ }
+ reg_write(dev, UNICAM_DAT0, val);
+
+ if (dev->active_data_lanes == 1)
+ val = 0;
+ reg_write(dev, UNICAM_DAT1, val);
+
+ if (dev->max_data_lanes > 2) {
+ /*
+ * Registers UNICAM_DAT2 and UNICAM_DAT3 only valid if the
+ * instance supports more than 2 data lanes.
+ */
+ if (dev->active_data_lanes == 2)
+ val = 0;
+ reg_write(dev, UNICAM_DAT2, val);
+
+ if (dev->active_data_lanes == 3)
+ val = 0;
+ reg_write(dev, UNICAM_DAT3, val);
+ }
+
+ reg_write(dev, UNICAM_IBLS,
+ dev->node[IMAGE_NODE].v_fmt.fmt.pix.bytesperline);
+ size = dev->node[IMAGE_NODE].v_fmt.fmt.pix.sizeimage;
+ unicam_wr_dma_addr(dev, addr[IMAGE_NODE], size, IMAGE_NODE);
+ unicam_set_packing_config(dev);
+ unicam_cfg_image_id(dev);
+
+ val = reg_read(dev, UNICAM_MISC);
+ set_field(&val, 1, UNICAM_FL0);
+ set_field(&val, 1, UNICAM_FL1);
+ reg_write(dev, UNICAM_MISC, val);
+
+ if (dev->node[METADATA_NODE].streaming && dev->sensor_embedded_data) {
+ unicam_dbg(3, dev, "enable metadata dma\n");
+ size = dev->node[METADATA_NODE].v_fmt.fmt.meta.buffersize;
+ unicam_enable_ed(dev);
+ unicam_wr_dma_addr(dev, addr[METADATA_NODE], size, METADATA_NODE);
+ }
+
+ /* Enable peripheral */
+ reg_write_field(dev, UNICAM_CTRL, 1, UNICAM_CPE);
+
+ /* Load image pointers */
+ reg_write_field(dev, UNICAM_ICTL, 1, UNICAM_LIP_MASK);
+
+ /* Load embedded data buffer pointers if needed */
+ if (dev->node[METADATA_NODE].streaming && dev->sensor_embedded_data)
+ reg_write_field(dev, UNICAM_DCS, 1, UNICAM_LDP);
+
+ /*
+ * Enable trigger only for the first frame to
+ * sync correctly to the FS from the source.
+ */
+ reg_write_field(dev, UNICAM_ICTL, 1, UNICAM_TFC);
+}
+
+static void unicam_disable(struct unicam_device *dev)
+{
+ /* Analogue lane control disable */
+ reg_write_field(dev, UNICAM_ANA, 1, UNICAM_DDL);
+
+ /* Stop the output engine */
+ reg_write_field(dev, UNICAM_CTRL, 1, UNICAM_SOE);
+
+ /* Disable the data lanes. */
+ reg_write(dev, UNICAM_DAT0, 0);
+ reg_write(dev, UNICAM_DAT1, 0);
+
+ if (dev->max_data_lanes > 2) {
+ reg_write(dev, UNICAM_DAT2, 0);
+ reg_write(dev, UNICAM_DAT3, 0);
+ }
+
+ /* Peripheral reset */
+ reg_write_field(dev, UNICAM_CTRL, 1, UNICAM_CPR);
+ usleep_range(50, 100);
+ reg_write_field(dev, UNICAM_CTRL, 0, UNICAM_CPR);
+
+ /* Disable peripheral */
+ reg_write_field(dev, UNICAM_CTRL, 0, UNICAM_CPE);
+
+ /* Clear ED setup */
+ reg_write(dev, UNICAM_DCS, 0);
+
+ /* Disable all lane clocks */
+ clk_write(dev, 0);
+}
+
+static void unicam_return_buffers(struct unicam_node *node,
+ enum vb2_buffer_state state)
+{
+ struct unicam_buffer *buf, *tmp;
+ unsigned long flags;
+
+ spin_lock_irqsave(&node->dma_queue_lock, flags);
+ list_for_each_entry_safe(buf, tmp, &node->dma_queue, list) {
+ list_del(&buf->list);
+ vb2_buffer_done(&buf->vb.vb2_buf, state);
+ }
+
+ if (node->cur_frm)
+ vb2_buffer_done(&node->cur_frm->vb.vb2_buf,
+ state);
+ if (node->next_frm && node->cur_frm != node->next_frm)
+ vb2_buffer_done(&node->next_frm->vb.vb2_buf,
+ state);
+
+ node->cur_frm = NULL;
+ node->next_frm = NULL;
+ spin_unlock_irqrestore(&node->dma_queue_lock, flags);
+}
+
+static int unicam_video_check_format(struct unicam_node *node)
+{
+ const struct v4l2_mbus_framefmt *format;
+ struct media_pad *remote_pad;
+ struct v4l2_subdev_state *state;
+ int ret = 0;
+
+ remote_pad = media_entity_remote_pad(&node->pad);
+ if (!remote_pad)
+ return -ENODEV;
+
+ state = v4l2_subdev_lock_active_state(node->dev->sensor);
+
+ format = v4l2_state_get_stream_format(state,
+ remote_pad->index, 0);
+ if (!format) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ if (node->fmt->code != format->code ||
+ node->v_fmt.fmt.pix.height != format->height ||
+ node->v_fmt.fmt.pix.width != format->width ||
+ node->v_fmt.fmt.pix.field != format->field) {
+ ret = -EPIPE;
+ goto out;
+ }
+
+out:
+ v4l2_subdev_unlock_state(state);
+
+ return ret;
+}
+
+static int unicam_start_streaming(struct vb2_queue *vq, unsigned int count)
+{
+ struct unicam_node *node = vb2_get_drv_priv(vq);
+ struct unicam_device *dev = node->dev;
+ dma_addr_t buffer_addr[MAX_NODES] = { 0 };
+ struct unicam_buffer *buf;
+ unsigned long flags;
+ unsigned int i;
+ int ret;
+
+ node->streaming = true;
+
+ dev->sequence = 0;
+ ret = unicam_runtime_get(dev);
+ if (ret < 0) {
+ unicam_dbg(3, dev, "unicam_runtime_get failed\n");
+ goto err_streaming;
+ }
+
+ ret = media_pipeline_start(node->video_dev.entity.pads, &node->pipe);
+ if (ret < 0) {
+ unicam_err(dev, "Failed to start media pipeline: %d\n", ret);
+ goto err_pm_put;
+ }
+
+ dev->active_data_lanes = dev->max_data_lanes;
+
+ unicam_video_check_format(node);
+
+ unicam_dbg(1, dev, "Running with %u data lanes\n",
+ dev->active_data_lanes);
+
+ ret = clk_set_min_rate(dev->vpu_clock, MIN_VPU_CLOCK_RATE);
+ if (ret) {
+ unicam_err(dev, "failed to set up VPU clock\n");
+ goto error_pipeline;
+ }
+
+ ret = clk_prepare_enable(dev->vpu_clock);
+ if (ret) {
+ unicam_err(dev, "Failed to enable VPU clock: %d\n", ret);
+ goto error_pipeline;
+ }
+
+ ret = clk_set_rate(dev->clock, 100 * 1000 * 1000);
+ if (ret) {
+ unicam_err(dev, "failed to set up CSI clock\n");
+ goto err_vpu_clock;
+ }
+
+ ret = clk_prepare_enable(dev->clock);
+ if (ret) {
+ unicam_err(dev, "Failed to enable CSI clock: %d\n", ret);
+ goto err_vpu_clock;
+ }
+
+ unicam_dbg(3, dev, "node %s\n", node->video_dev.name);
+
+ spin_lock_irqsave(&node->dma_queue_lock, flags);
+ buf = list_first_entry(&node->dma_queue,
+ struct unicam_buffer, list);
+ node->cur_frm = buf;
+ node->next_frm = buf;
+ list_del(&buf->list);
+ spin_unlock_irqrestore(&node->dma_queue_lock, flags);
+
+ buffer_addr[i] =
+ vb2_dma_contig_plane_dma_addr(&buf->vb.vb2_buf, 0);
+
+ unicam_start_rx(dev, buffer_addr);
+
+ ret = v4l2_subdev_call(&dev->sd, video, s_stream, 1);
+ if (ret < 0) {
+ unicam_err(dev, "stream on failed in subdev\n");
+ goto err_disable_unicam;
+ }
+
+ dev->clocks_enabled = true;
+ return 0;
+
+err_disable_unicam:
+ unicam_disable(dev);
+ clk_disable_unprepare(dev->clock);
+err_vpu_clock:
+ if (clk_set_min_rate(dev->vpu_clock, 0))
+ unicam_err(dev, "failed to reset the VPU clock\n");
+ clk_disable_unprepare(dev->vpu_clock);
+error_pipeline:
+ media_pipeline_stop(node->video_dev.entity.pads);
+err_pm_put:
+ unicam_runtime_put(dev);
+err_streaming:
+ unicam_return_buffers(node, VB2_BUF_STATE_QUEUED);
+ node->streaming = false;
+
+ return ret;
+}
+
+static void unicam_stop_streaming(struct vb2_queue *vq)
+{
+ struct unicam_node *node = vb2_get_drv_priv(vq);
+ struct unicam_device *dev = node->dev;
+
+ node->streaming = false;
+ /*
+ * Stop streaming the sensor and disable the peripheral.
+ * We cannot continue streaming embedded data with the
+ * image pad disabled.
+ */
+ if (v4l2_subdev_call(dev->sensor, video, s_stream, 0) < 0)
+ unicam_err(dev, "stream off failed in subdev\n");
+
+ unicam_disable(dev);
+
+ media_pipeline_stop(node->video_dev.entity.pads);
+
+ if (dev->clocks_enabled) {
+ if (clk_set_min_rate(dev->vpu_clock, 0))
+ unicam_err(dev, "failed to reset the VPU clock\n");
+ clk_disable_unprepare(dev->vpu_clock);
+ clk_disable_unprepare(dev->clock);
+ dev->clocks_enabled = false;
+ }
+ unicam_runtime_put(dev);
+
+ if (is_metadata_node(node)) {
+ /*
+ * Allow the hardware to spin in the dummy buffer.
+ * This is only really needed if the embedded data pad is
+ * disabled before the image pad.
+ */
+ unicam_wr_dma_addr(dev, node->dummy_buf_dma_addr,
+ DUMMY_BUF_SIZE, METADATA_NODE);
+ }
+
+ /* Clear all queued buffers for the node */
+ unicam_return_buffers(node, VB2_BUF_STATE_ERROR);
+}
+
+static const struct vb2_ops unicam_video_qops = {
+ .wait_prepare = vb2_ops_wait_prepare,
+ .wait_finish = vb2_ops_wait_finish,
+ .queue_setup = unicam_queue_setup,
+ .buf_prepare = unicam_buffer_prepare,
+ .buf_queue = unicam_buffer_queue,
+ .start_streaming = unicam_start_streaming,
+ .stop_streaming = unicam_stop_streaming,
+};
+
+/* unicam capture driver file operations */
+static const struct v4l2_file_operations unicam_fops = {
+ .owner = THIS_MODULE,
+ .open = v4l2_fh_open,
+ .release = vb2_fop_release,
+ .poll = vb2_fop_poll,
+ .unlocked_ioctl = video_ioctl2, /* V4L2 ioctl handler */
+ .mmap = vb2_fop_mmap,
+};
+
+static int
+unicam_async_bound(struct v4l2_async_notifier *notifier,
+ struct v4l2_subdev *subdev,
+ struct v4l2_async_subdev *asd)
+{
+ struct unicam_device *unicam = to_unicam_device(notifier->v4l2_dev);
+
+ if (unicam->sensor) {
+ unicam_info(unicam, "Rejecting subdev %s (Already set!!)",
+ subdev->name);
+ return 0;
+ }
+
+ unicam->sensor = subdev;
+ unicam_dbg(1, unicam, "Using sensor %s for capture\n", subdev->name);
+
+ return 0;
+}
+
+static void unicam_release(struct kref *kref)
+{
+ struct unicam_device *unicam =
+ container_of(kref, struct unicam_device, kref);
+
+ v4l2_ctrl_handler_free(&unicam->ctrl_handler);
+ media_device_cleanup(&unicam->mdev);
+
+ if (unicam->sensor_state)
+ __v4l2_subdev_state_free(unicam->sensor_state);
+
+ kfree(unicam);
+}
+
+static void unicam_put(struct unicam_device *unicam)
+{
+ kref_put(&unicam->kref, unicam_release);
+}
+
+static void unicam_get(struct unicam_device *unicam)
+{
+ kref_get(&unicam->kref);
+}
+
+static void unicam_node_release(struct video_device *vdev)
+{
+ struct unicam_node *node = video_get_drvdata(vdev);
+
+ unicam_put(node->dev);
+}
+
+static void unicam_mc_set_default_format(struct unicam_node *node)
+{
+ unicam_dbg(3, node->dev, "Set default format for %s node\n",
+ node->node_id == IMAGE_NODE ? "image" : "metadata");
+
+ if (is_image_node(node)) {
+ struct v4l2_pix_format *pix_fmt = &node->v_fmt.fmt.pix;
+
+ pix_fmt->width = 640;
+ pix_fmt->height = 480;
+ pix_fmt->field = V4L2_FIELD_NONE;
+ pix_fmt->colorspace = V4L2_COLORSPACE_SRGB;
+ pix_fmt->ycbcr_enc = V4L2_YCBCR_ENC_601;
+ pix_fmt->quantization = V4L2_QUANTIZATION_LIM_RANGE;
+ pix_fmt->xfer_func = V4L2_XFER_FUNC_SRGB;
+ pix_fmt->pixelformat = formats[0].fourcc;
+ unicam_calc_format_size_bpl(node->dev, &formats[0],
+ &node->v_fmt);
+ node->v_fmt.type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
+
+ node->fmt = &formats[0];
+ } else {
+ const struct unicam_fmt *fmt;
+
+ /* Fix this node format as embedded data. */
+ fmt = find_format_by_code(MEDIA_BUS_FMT_METADATA_8);
+ node->v_fmt.fmt.meta.dataformat = fmt->fourcc;
+ node->fmt = fmt;
+ node->v_fmt.fmt.meta.buffersize = UNICAM_EMBEDDED_SIZE;
+ node->embedded_lines = 1;
+ node->v_fmt.type = V4L2_BUF_TYPE_META_CAPTURE;
+ }
+}
+
+static int register_node(struct unicam_device *unicam, struct unicam_node *node,
+ enum v4l2_buf_type type)
+{
+ struct video_device *vdev;
+ struct vb2_queue *q;
+ int ret;
+
+ node->dev = unicam;
+ node->node_id = type == V4L2_BUF_TYPE_VIDEO_CAPTURE ?
+ IMAGE_NODE :
+ METADATA_NODE;
+
+ spin_lock_init(&node->dma_queue_lock);
+ mutex_init(&node->lock);
+
+ vdev = &node->video_dev;
+ /*
+ * If the sensor subdevice has any controls, associate the node
+ * with the ctrl handler to allow access from userland.
+ */
+ if (!list_empty(&unicam->ctrl_handler.ctrls))
+ vdev->ctrl_handler = &unicam->ctrl_handler;
+
+ q = &node->buffer_queue;
+ q->type = type;
+ q->io_modes = VB2_MMAP | VB2_DMABUF | VB2_READ;
+ q->drv_priv = node;
+ q->ops = &unicam_video_qops;
+ q->mem_ops = &vb2_dma_contig_memops;
+ q->buf_struct_size = sizeof(struct unicam_buffer);
+ q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC;
+ q->lock = &node->lock;
+ q->min_buffers_needed = 1;
+ q->dev = &unicam->pdev->dev;
+
+ ret = vb2_queue_init(q);
+ if (ret) {
+ unicam_err(unicam, "vb2_queue_init() failed\n");
+ return ret;
+ }
+
+ INIT_LIST_HEAD(&node->dma_queue);
+
+ vdev->release = unicam_node_release;
+ vdev->fops = &unicam_fops;
+ vdev->ioctl_ops = &unicam_mc_ioctl_ops;
+ vdev->v4l2_dev = &unicam->v4l2_dev;
+ vdev->vfl_dir = VFL_DIR_RX;
+ vdev->queue = q;
+ vdev->lock = &node->lock;
+ vdev->device_caps = (type == V4L2_BUF_TYPE_VIDEO_CAPTURE) ?
+ V4L2_CAP_VIDEO_CAPTURE : V4L2_CAP_META_CAPTURE;
+ vdev->device_caps |= V4L2_CAP_READWRITE | V4L2_CAP_STREAMING | V4L2_CAP_IO_MC;
+ vdev->entity.ops = &unicam_mc_entity_ops;
+
+ /* Define the device names */
+ snprintf(vdev->name, sizeof(vdev->name), "%s-%s", UNICAM_MODULE_NAME,
+ type == V4L2_BUF_TYPE_VIDEO_CAPTURE ? "image" : "embedded");
+
+ video_set_drvdata(vdev, node);
+ if (type == V4L2_BUF_TYPE_VIDEO_CAPTURE)
+ vdev->entity.flags |= MEDIA_ENT_FL_DEFAULT;
+ node->pad.flags = MEDIA_PAD_FL_SINK;
+ media_entity_pads_init(&vdev->entity, 1, &node->pad);
+
+ node->dummy_buf_cpu_addr = dma_alloc_coherent(&unicam->pdev->dev,
+ DUMMY_BUF_SIZE,
+ &node->dummy_buf_dma_addr,
+ GFP_KERNEL);
+ if (!node->dummy_buf_cpu_addr) {
+ unicam_err(unicam, "Unable to allocate dummy buffer.\n");
+ return -ENOMEM;
+ }
+
+ ret = video_register_device(vdev, VFL_TYPE_VIDEO, -1);
+ if (ret) {
+ unicam_err(unicam, "Unable to register video device %s\n",
+ vdev->name);
+ return ret;
+ }
+
+ /*
+ * Acquire a reference to unicam, which will be released when the video
+ * device will be unregistered and userspace will have closed all open
+ * file handles.
+ */
+ unicam_get(unicam);
+ node->registered = true;
+
+ ret = media_create_pad_link(&unicam->sd.entity,
+ node->src_pad_id,
+ &node->video_dev.entity,
+ 0,
+ MEDIA_LNK_FL_ENABLED |
+ MEDIA_LNK_FL_IMMUTABLE);
+ if (ret)
+ unicam_err(unicam, "Unable to create pad link for %s",
+ unicam->sensor->name);
+
+ unicam_mc_set_default_format(node);
+
+ return ret;
+}
+
+static void unregister_nodes(struct unicam_device *unicam)
+{
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(unicam->node); i++) {
+ struct unicam_node *node = &unicam->node[i];
+
+ if (node->dummy_buf_cpu_addr) {
+ dma_free_coherent(&unicam->pdev->dev, DUMMY_BUF_SIZE,
+ node->dummy_buf_cpu_addr,
+ node->dummy_buf_dma_addr);
+ }
+
+ if (node->registered) {
+ node->registered = false;
+ video_unregister_device(&node->video_dev);
+ }
+ }
+}
+
+static int unicam_async_complete(struct v4l2_async_notifier *notifier)
+{
+ struct unicam_device *unicam = to_unicam_device(notifier->v4l2_dev);
+ unsigned int i, source_pads = 0;
+ int ret;
+ static struct lock_class_key key;
+
+ unicam->v4l2_dev.notify = unicam_notify;
+
+ unicam->sensor_state = __v4l2_subdev_state_alloc(unicam->sensor,
+ "unicam:state->lock",
+ &key);
+ if (!unicam->sensor_state)
+ return -ENOMEM;
+
+ for (i = 0; i < unicam->sd.entity.num_pads; i++) {
+ if (unicam->sd.entity.pads[i].flags & MEDIA_PAD_FL_SOURCE) {
+ if (source_pads < MAX_NODES) {
+ unicam->node[source_pads].src_pad_id = i;
+ unicam_dbg(3, unicam, "source pad %u is index %u\n",
+ source_pads, i);
+ }
+ source_pads++;
+ }
+ }
+ if (!source_pads) {
+ unicam_err(unicam, "No source pads on sensor.\n");
+ goto unregister;
+ }
+
+ ret = register_node(unicam, &unicam->node[IMAGE_NODE],
+ V4L2_BUF_TYPE_VIDEO_CAPTURE);
+ if (ret) {
+ unicam_err(unicam, "Unable to register image video device.\n");
+ goto unregister;
+ }
+
+ /* \todo: check before :-) */
+ unicam->sensor_embedded_data = true;
+
+ ret = register_node(unicam, &unicam->node[METADATA_NODE],
+ V4L2_BUF_TYPE_META_CAPTURE);
+ if (ret) {
+ unicam_err(unicam, "Unable to register metadata video device.\n");
+ goto unregister;
+ }
+
+ ret = media_create_pad_link(&unicam->sensor->entity,
+ 0,
+ &unicam->sd.entity,
+ UNICAM_SD_PAD_SINK,
+ MEDIA_LNK_FL_ENABLED |
+ MEDIA_LNK_FL_IMMUTABLE);
+ if (ret)
+ unicam_err(unicam, "Unable to create pad link for %s",
+ unicam->sensor->name);
+
+ ret = v4l2_device_register_subdev_nodes(&unicam->v4l2_dev);
+ if (ret) {
+ unicam_err(unicam, "Unable to register subdev nodes.\n");
+ goto unregister;
+ }
+
+ /*
+ * Release the initial reference, all references are now owned by the
+ * video devices.
+ */
+ unicam_put(unicam);
+ return 0;
+
+unregister:
+ unregister_nodes(unicam);
+ unicam_put(unicam);
+
+ return ret;
+}
+
+static const struct v4l2_async_notifier_operations unicam_async_ops = {
+ .bound = unicam_async_bound,
+ .complete = unicam_async_complete,
+};
+
+static int of_unicam_connect_subdevs(struct unicam_device *dev)
+{
+ struct platform_device *pdev = dev->pdev;
+ struct v4l2_fwnode_endpoint ep = { };
+ struct device_node *ep_node;
+ struct device_node *sensor_node;
+ unsigned int lane;
+ int ret = -EINVAL;
+
+ if (of_property_read_u32(pdev->dev.of_node, "brcm,num-data-lanes",
+ &dev->max_data_lanes) < 0) {
+ unicam_err(dev, "number of data lanes not set\n");
+ return -EINVAL;
+ }
+
+ /* Get the local endpoint and remote device. */
+ ep_node = of_graph_get_next_endpoint(pdev->dev.of_node, NULL);
+ if (!ep_node) {
+ unicam_dbg(3, dev, "can't get next endpoint\n");
+ return -EINVAL;
+ }
+
+ unicam_dbg(3, dev, "ep_node is %pOF\n", ep_node);
+
+ sensor_node = of_graph_get_remote_port_parent(ep_node);
+ if (!sensor_node) {
+ unicam_dbg(3, dev, "can't get remote parent\n");
+ goto cleanup_exit;
+ }
+
+ unicam_dbg(1, dev, "found subdevice %pOF\n", sensor_node);
+
+ /* Parse the local endpoint and validate its configuration. */
+ v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep_node), &ep);
+
+ unicam_dbg(3, dev, "parsed local endpoint, bus_type %u\n",
+ ep.bus_type);
+
+ dev->bus_type = ep.bus_type;
+
+ switch (ep.bus_type) {
+ case V4L2_MBUS_CSI2_DPHY:
+ switch (ep.bus.mipi_csi2.num_data_lanes) {
+ case 1:
+ case 2:
+ case 4:
+ break;
+
+ default:
+ unicam_err(dev, "subdevice %pOF: %u data lanes not supported\n",
+ sensor_node,
+ ep.bus.mipi_csi2.num_data_lanes);
+ goto cleanup_exit;
+ }
+
+ for (lane = 0; lane < ep.bus.mipi_csi2.num_data_lanes; lane++) {
+ if (ep.bus.mipi_csi2.data_lanes[lane] != lane + 1) {
+ unicam_err(dev, "subdevice %pOF: data lanes reordering not supported\n",
+ sensor_node);
+ goto cleanup_exit;
+ }
+ }
+
+ if (ep.bus.mipi_csi2.num_data_lanes > dev->max_data_lanes) {
+ unicam_err(dev, "subdevice requires %u data lanes when %u are supported\n",
+ ep.bus.mipi_csi2.num_data_lanes,
+ dev->max_data_lanes);
+ }
+
+ dev->max_data_lanes = ep.bus.mipi_csi2.num_data_lanes;
+ dev->bus_flags = ep.bus.mipi_csi2.flags;
+
+ break;
+
+ case V4L2_MBUS_CCP2:
+ if (ep.bus.mipi_csi1.clock_lane != 0 ||
+ ep.bus.mipi_csi1.data_lane != 1) {
+ unicam_err(dev, "subdevice %pOF: unsupported lanes configuration\n",
+ sensor_node);
+ goto cleanup_exit;
+ }
+
+ dev->max_data_lanes = 1;
+ dev->bus_flags = ep.bus.mipi_csi1.strobe;
+ break;
+
+ default:
+ /* Unsupported bus type */
+ unicam_err(dev, "subdevice %pOF: unsupported bus type %u\n",
+ sensor_node, ep.bus_type);
+ goto cleanup_exit;
+ }
+
+ unicam_dbg(3, dev, "subdevice %pOF: %s bus, %u data lanes, flags=0x%08x\n",
+ sensor_node,
+ dev->bus_type == V4L2_MBUS_CSI2_DPHY ? "CSI-2" : "CCP2",
+ dev->max_data_lanes, dev->bus_flags);
+
+ /* Initialize and register the async notifier. */
+ v4l2_async_nf_init(&dev->notifier);
+ dev->notifier.ops = &unicam_async_ops;
+
+ dev->asd.match_type = V4L2_ASYNC_MATCH_FWNODE;
+ dev->asd.match.fwnode = fwnode_graph_get_remote_endpoint(of_fwnode_handle(ep_node));
+ ret = v4l2_async_nf_add_subdev(&dev->notifier, &dev->asd);
+ if (ret) {
+ unicam_err(dev, "Error adding subdevice: %d\n", ret);
+ goto cleanup_exit;
+ }
+
+ ret = v4l2_async_nf_register(&dev->v4l2_dev, &dev->notifier);
+ if (ret) {
+ unicam_err(dev, "Error registering async notifier: %d\n", ret);
+ ret = -EINVAL;
+ }
+
+cleanup_exit:
+ of_node_put(sensor_node);
+ of_node_put(ep_node);
+
+ return ret;
+}
+
+static int bcm2835_media_dev_init(struct unicam_device *unicam,
+ struct platform_device *pdev)
+{
+ int ret = 0;
+
+ unicam->mdev.dev = &pdev->dev;
+ strscpy(unicam->mdev.model, UNICAM_MODULE_NAME,
+ sizeof(unicam->mdev.model));
+ strscpy(unicam->mdev.serial, "", sizeof(unicam->mdev.serial));
+ snprintf(unicam->mdev.bus_info, sizeof(unicam->mdev.bus_info),
+ "platform:%s", dev_name(&pdev->dev));
+ unicam->mdev.hw_revision = 0;
+
+ media_device_init(&unicam->mdev);
+
+ unicam->v4l2_dev.mdev = &unicam->mdev;
+
+ ret = v4l2_device_register(&pdev->dev, &unicam->v4l2_dev);
+
+ return ret;
+}
+
+/* Internal subdev */
+
+static int _unicam_subdev_set_routing(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_krouting *routing)
+{
+ static const struct v4l2_mbus_framefmt format = {
+ .width = 640,
+ .height = 480,
+ .code = MEDIA_BUS_FMT_UYVY8_2X8,
+ .field = V4L2_FIELD_NONE,
+ .colorspace = V4L2_COLORSPACE_SRGB,
+ .ycbcr_enc = V4L2_YCBCR_ENC_601,
+ .quantization = V4L2_QUANTIZATION_LIM_RANGE,
+ .xfer_func = V4L2_XFER_FUNC_SRGB,
+ .flags = 0,
+ };
+ int ret;
+
+ ret = v4l2_subdev_routing_validate_1_to_1(routing);
+ if (ret)
+ return ret;
+
+ v4l2_subdev_lock_state(state);
+
+ ret = v4l2_subdev_set_routing_with_fmt(sd, state, routing, &format);
+
+ v4l2_subdev_unlock_state(state);
+
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int unicam_subdev_set_routing(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ enum v4l2_subdev_format_whence which,
+ struct v4l2_subdev_krouting *routing)
+{
+ struct unicam_device *unicam = sd_to_unicam_device(sd);
+
+ if (which == V4L2_SUBDEV_FORMAT_ACTIVE && unicam->streaming)
+ return -EBUSY;
+
+ return _unicam_subdev_set_routing(sd, state, routing);
+}
+
+static int unicam_subdev_init_cfg(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state)
+{
+ struct v4l2_subdev_route routes[] = {
+ {
+ .sink_pad = 0,
+ .sink_stream = 0,
+ .source_pad = 1,
+ .source_stream = 0,
+ .flags = V4L2_SUBDEV_ROUTE_FL_ACTIVE,
+ },
+ };
+
+ struct v4l2_subdev_krouting routing = {
+ .num_routes = ARRAY_SIZE(routes),
+ .routes = routes,
+ };
+
+ /* Initialize routing to single route to the fist source pad */
+ return _unicam_subdev_set_routing(sd, state, &routing);
+}
+
+static int unicam_subdev_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ int ret = 0;
+
+ v4l2_subdev_lock_state(state);
+
+ /* No transcoding, source and sink codes must match. */
+ if (unicam_sd_pad_is_source(code->pad)) {
+ struct v4l2_mbus_framefmt *fmt;
+
+ if (code->index > 0) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ fmt = v4l2_subdev_state_get_opposite_stream_format(state,
+ code->pad,
+ code->stream);
+ if (!fmt) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ code->code = fmt->code;
+ } else {
+ if (code->index >= ARRAY_SIZE(formats)) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ code->code = formats[code->index].code;
+ }
+
+out:
+ v4l2_subdev_unlock_state(state);
+
+ return ret;
+}
+
+static int unicam_subdev_start_streaming(struct unicam_device *unicam)
+{
+ const struct v4l2_subdev_krouting *routing;
+ struct v4l2_subdev_state *state;
+ int ret = 0;
+
+ state = v4l2_subdev_lock_active_state(&unicam->sd);
+
+ routing = &state->routing;
+
+ v4l2_subdev_unlock_state(state);
+
+ unicam->streaming = true;
+
+ ret = v4l2_subdev_call(unicam->sensor, video, s_stream, 1);
+ if (ret) {
+ v4l2_subdev_call(unicam->sensor, video, s_stream, 0);
+ unicam->streaming = false;
+ return ret;
+ }
+
+ return 0;
+}
+
+static int unicam_subdev_stop_streaming(struct unicam_device *unicam)
+{
+ v4l2_subdev_call(unicam->sensor, video, s_stream, 0);
+
+ unicam->streaming = false;
+
+ return 0;
+}
+
+static int unicam_subdev_s_stream(struct v4l2_subdev *sd, int enable)
+{
+ struct unicam_device *unicam = sd_to_unicam_device(sd);
+
+ if (enable)
+ return unicam_subdev_start_streaming(unicam);
+ else
+ return unicam_subdev_stop_streaming(unicam);
+ return 0;
+}
+
+static int unicam_subdev_set_pad_format(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_format *format)
+{
+ struct unicam_device *unicam = sd_to_unicam_device(sd);
+ struct v4l2_mbus_framefmt *fmt;
+ int ret = 0;
+
+ if (format->which == V4L2_SUBDEV_FORMAT_ACTIVE && unicam->streaming)
+ return -EBUSY;
+
+ /* No transcoding, source and sink formats must match. */
+ if (unicam_sd_pad_is_source(format->pad))
+ return v4l2_subdev_get_fmt(sd, state, format);
+
+ // TODO: implement fmt validation
+
+ v4l2_subdev_lock_state(state);
+
+ fmt = v4l2_state_get_stream_format(state, format->pad, format->stream);
+ if (!fmt) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ *fmt = format->format;
+
+ fmt = v4l2_subdev_state_get_opposite_stream_format(state, format->pad,
+ format->stream);
+ if (!fmt) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ *fmt = format->format;
+
+out:
+ v4l2_subdev_unlock_state(state);
+
+ return ret;
+}
+
+static int unicam_subdev_enum_frame_size(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_frame_size_enum *fse)
+{
+ const struct unicam_fmt *fmtinfo;
+ int ret = 0;
+
+ if (fse->index > 0)
+ return -EINVAL;
+
+ v4l2_subdev_lock_state(state);
+
+ /* No transcoding, source and sink formats must match. */
+ if (unicam_sd_pad_is_source(fse->pad)) {
+ struct v4l2_mbus_framefmt *fmt;
+
+ fmt = v4l2_subdev_state_get_opposite_stream_format(state,
+ fse->pad,
+ fse->stream);
+
+ if (!fmt) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ if (fse->code != fmt->code) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ fse->min_width = fmt->width;
+ fse->max_width = fmt->width;
+ fse->min_height = fmt->height;
+ fse->max_height = fmt->height;
+ } else {
+ fmtinfo = find_format_by_code(fse->code);
+ if (!fmtinfo) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ fse->min_width = MIN_WIDTH * 8 / ALIGN(fmtinfo->depth, 8);
+ fse->max_width = MAX_WIDTH * 8 / ALIGN(fmtinfo->depth, 8);
+ fse->min_height = MIN_HEIGHT;
+ fse->max_height = MAX_HEIGHT;
+ }
+
+out:
+ v4l2_subdev_unlock_state(state);
+
+ return ret;
+}
+
+static const struct v4l2_subdev_video_ops unicam_subdev_video_ops = {
+ .s_stream = unicam_subdev_s_stream,
+};
+
+static const struct v4l2_subdev_pad_ops unicam_subdev_pad_ops = {
+ .init_cfg = unicam_subdev_init_cfg,
+ .enum_mbus_code = unicam_subdev_enum_mbus_code,
+ .get_fmt = v4l2_subdev_get_fmt,
+ .set_fmt = unicam_subdev_set_pad_format,
+ .set_routing = unicam_subdev_set_routing,
+ .enum_frame_size = unicam_subdev_enum_frame_size,
+};
+
+static const struct v4l2_subdev_ops unicam_subdev_ops = {
+ .video = &unicam_subdev_video_ops,
+ .pad = &unicam_subdev_pad_ops,
+};
+
+static struct media_entity_operations unicam_subdev_media_ops = {
+ .link_validate = v4l2_subdev_link_validate,
+ .has_route = v4l2_subdev_has_route,
+};
+
+static int unicam_probe(struct platform_device *pdev)
+{
+ struct unicam_device *unicam;
+ int ret = 0;
+ int i;
+
+ unicam = kzalloc(sizeof(*unicam), GFP_KERNEL);
+ if (!unicam)
+ return -ENOMEM;
+
+ kref_init(&unicam->kref);
+ unicam->pdev = pdev;
+
+ /*
+ * Adopt the current setting of the module parameter, and check if
+ * device tree requests it.
+ */
+ if (!of_property_read_bool(pdev->dev.of_node, "brcm,media-controller")) {
+ unicam_err(unicam, "Failed to find media-controller node\n");
+ goto err_unicam_put;
+ }
+
+ unicam->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(unicam->base)) {
+ unicam_err(unicam, "Failed to get main io block\n");
+ ret = PTR_ERR(unicam->base);
+ goto err_unicam_put;
+ }
+
+ unicam->clk_gate_base = devm_platform_ioremap_resource(pdev, 1);
+ if (IS_ERR(unicam->clk_gate_base)) {
+ unicam_err(unicam, "Failed to get 2nd io block\n");
+ ret = PTR_ERR(unicam->clk_gate_base);
+ goto err_unicam_put;
+ }
+
+ unicam->clock = devm_clk_get(&pdev->dev, "lp");
+ if (IS_ERR(unicam->clock)) {
+ unicam_err(unicam, "Failed to get lp clock\n");
+ ret = PTR_ERR(unicam->clock);
+ goto err_unicam_put;
+ }
+
+ unicam->vpu_clock = devm_clk_get(&pdev->dev, "vpu");
+ if (IS_ERR(unicam->vpu_clock)) {
+ unicam_err(unicam, "Failed to get vpu clock\n");
+ ret = PTR_ERR(unicam->vpu_clock);
+ goto err_unicam_put;
+ }
+
+ ret = platform_get_irq(pdev, 0);
+ if (ret <= 0) {
+ dev_err(&pdev->dev, "No IRQ resource\n");
+ ret = -EINVAL;
+ goto err_unicam_put;
+ }
+
+ ret = devm_request_irq(&pdev->dev, ret, unicam_isr, 0,
+ "unicam_capture0", unicam);
+ if (ret) {
+ dev_err(&pdev->dev, "Unable to request interrupt\n");
+ ret = -EINVAL;
+ goto err_unicam_put;
+ }
+
+ ret = bcm2835_media_dev_init(unicam, pdev);
+ if (ret) {
+ unicam_err(unicam,
+ "Unable to register v4l2 device.\n");
+ goto err_unicam_put;
+ }
+
+ ret = media_device_register(&unicam->mdev);
+ if (ret < 0) {
+ unicam_err(unicam,
+ "Unable to register media-controller device.\n");
+ goto err_v4l2_unregister;
+ }
+
+ /* Reserve space for the controls */
+ ret = v4l2_ctrl_handler_init(&unicam->ctrl_handler, 16);
+ if (ret < 0)
+ goto err_media_unregister;
+
+ /* set the driver data in platform device */
+ platform_set_drvdata(pdev, unicam);
+
+ unicam_dbg(3, unicam, "Initialize internal subdev");
+ v4l2_subdev_init(&unicam->sd, &unicam_subdev_ops);
+ v4l2_set_subdevdata(&unicam->sd, unicam);
+ unicam->sd.entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
+ unicam->sd.dev = &pdev->dev;
+ unicam->sd.owner = THIS_MODULE;
+ unicam->sd.flags = V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_MULTIPLEXED;
+ snprintf(unicam->sd.name, sizeof(unicam->sd.name), "unicam-subdev");
+
+ unicam->pads[UNICAM_SD_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
+
+ for (i = UNICAM_SD_PAD_FIRST_SOURCE; i < UNICAM_SD_NUM_PADS; ++i)
+ unicam->pads[i].flags = MEDIA_PAD_FL_SOURCE;
+ unicam->sd.entity.ops = &unicam_subdev_media_ops;
+ ret = media_entity_pads_init(&unicam->sd.entity,
+ ARRAY_SIZE(unicam->pads), unicam->pads);
+ if (ret) {
+ unicam_err(unicam, "Could not init media controller for subdev");
+ goto err_subdev_unregister;
+ }
+
+ ret = v4l2_subdev_init_finalize(&unicam->sd);
+ if (ret) {
+ unicam_err(unicam, "Could not finalize init for subdev");
+ goto err_entity_cleanup;
+ }
+
+ ret = v4l2_device_register_subdev(&unicam->v4l2_dev, &unicam->sd);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to register internal subdev\n");
+ goto err_subdev_unregister;
+ }
+
+ ret = of_unicam_connect_subdevs(unicam);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to connect subdevs\n");
+ goto err_subdev_unregister;
+ }
+
+ /* Enable the block power domain */
+ pm_runtime_enable(&pdev->dev);
+
+ return 0;
+
+err_subdev_unregister:
+ v4l2_subdev_cleanup(&unicam->sd);
+err_entity_cleanup:
+ media_entity_cleanup(&unicam->sd.entity);
+err_media_unregister:
+ media_device_unregister(&unicam->mdev);
+err_v4l2_unregister:
+ v4l2_device_unregister(&unicam->v4l2_dev);
+err_unicam_put:
+ unicam_put(unicam);
+
+ return ret;
+}
+
+static int unicam_remove(struct platform_device *pdev)
+{
+ struct unicam_device *unicam = platform_get_drvdata(pdev);
+
+ v4l2_async_nf_unregister(&unicam->notifier);
+ v4l2_device_unregister(&unicam->v4l2_dev);
+ media_device_unregister(&unicam->mdev);
+ unregister_nodes(unicam);
+
+ pm_runtime_disable(&pdev->dev);
+
+ return 0;
+}
+
+static const struct of_device_id unicam_of_match[] = {
+ { .compatible = "brcm,bcm2835-unicam", },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, unicam_of_match);
+
+static struct platform_driver unicam_driver = {
+ .probe = unicam_probe,
+ .remove = unicam_remove,
+ .driver = {
+ .name = UNICAM_MODULE_NAME,
+ .of_match_table = of_match_ptr(unicam_of_match),
+ },
+};
+
+module_platform_driver(unicam_driver);
+
+MODULE_AUTHOR("Dave Stevenson <dave.stevenson@raspberrypi.com>");
+MODULE_DESCRIPTION("BCM2835 Unicam driver");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(UNICAM_VERSION);
new file mode 100644
@@ -0,0 +1,253 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+/*
+ * Copyright (C) 2017-2020 Raspberry Pi Trading.
+ * Dave Stevenson <dave.stevenson@raspberrypi.com>
+ */
+
+#ifndef VC4_REGS_UNICAM_H
+#define VC4_REGS_UNICAM_H
+
+/*
+ * The following values are taken from files found within the code drop
+ * made by Broadcom for the BCM21553 Graphics Driver, predominantly in
+ * brcm_usrlib/dag/vmcsx/vcinclude/hardware_vc4.h.
+ * They have been modified to be only the register offset.
+ */
+#define UNICAM_CTRL 0x000
+#define UNICAM_STA 0x004
+#define UNICAM_ANA 0x008
+#define UNICAM_PRI 0x00c
+#define UNICAM_CLK 0x010
+#define UNICAM_CLT 0x014
+#define UNICAM_DAT0 0x018
+#define UNICAM_DAT1 0x01c
+#define UNICAM_DAT2 0x020
+#define UNICAM_DAT3 0x024
+#define UNICAM_DLT 0x028
+#define UNICAM_CMP0 0x02c
+#define UNICAM_CMP1 0x030
+#define UNICAM_CAP0 0x034
+#define UNICAM_CAP1 0x038
+#define UNICAM_ICTL 0x100
+#define UNICAM_ISTA 0x104
+#define UNICAM_IDI0 0x108
+#define UNICAM_IPIPE 0x10c
+#define UNICAM_IBSA0 0x110
+#define UNICAM_IBEA0 0x114
+#define UNICAM_IBLS 0x118
+#define UNICAM_IBWP 0x11c
+#define UNICAM_IHWIN 0x120
+#define UNICAM_IHSTA 0x124
+#define UNICAM_IVWIN 0x128
+#define UNICAM_IVSTA 0x12c
+#define UNICAM_ICC 0x130
+#define UNICAM_ICS 0x134
+#define UNICAM_IDC 0x138
+#define UNICAM_IDPO 0x13c
+#define UNICAM_IDCA 0x140
+#define UNICAM_IDCD 0x144
+#define UNICAM_IDS 0x148
+#define UNICAM_DCS 0x200
+#define UNICAM_DBSA0 0x204
+#define UNICAM_DBEA0 0x208
+#define UNICAM_DBWP 0x20c
+#define UNICAM_DBCTL 0x300
+#define UNICAM_IBSA1 0x304
+#define UNICAM_IBEA1 0x308
+#define UNICAM_IDI1 0x30c
+#define UNICAM_DBSA1 0x310
+#define UNICAM_DBEA1 0x314
+#define UNICAM_MISC 0x400
+
+/*
+ * The following bitmasks are from the kernel released by Broadcom
+ * for Android - https://android.googlesource.com/kernel/bcm/
+ * The Rhea, Hawaii, and Java chips all contain the same VideoCore4
+ * Unicam block as BCM2835, as defined in eg
+ * arch/arm/mach-rhea/include/mach/rdb_A0/brcm_rdb_cam.h and similar.
+ * Values reworked to use the kernel BIT and GENMASK macros.
+ *
+ * Some of the bit mnenomics have been amended to match the datasheet.
+ */
+/* UNICAM_CTRL Register */
+#define UNICAM_CPE BIT(0)
+#define UNICAM_MEM BIT(1)
+#define UNICAM_CPR BIT(2)
+#define UNICAM_CPM_MASK GENMASK(3, 3)
+#define UNICAM_CPM_CSI2 0
+#define UNICAM_CPM_CCP2 1
+#define UNICAM_SOE BIT(4)
+#define UNICAM_DCM_MASK GENMASK(5, 5)
+#define UNICAM_DCM_STROBE 0
+#define UNICAM_DCM_DATA 1
+#define UNICAM_SLS BIT(6)
+#define UNICAM_PFT_MASK GENMASK(11, 8)
+#define UNICAM_OET_MASK GENMASK(20, 12)
+
+/* UNICAM_STA Register */
+#define UNICAM_SYN BIT(0)
+#define UNICAM_CS BIT(1)
+#define UNICAM_SBE BIT(2)
+#define UNICAM_PBE BIT(3)
+#define UNICAM_HOE BIT(4)
+#define UNICAM_PLE BIT(5)
+#define UNICAM_SSC BIT(6)
+#define UNICAM_CRCE BIT(7)
+#define UNICAM_OES BIT(8)
+#define UNICAM_IFO BIT(9)
+#define UNICAM_OFO BIT(10)
+#define UNICAM_BFO BIT(11)
+#define UNICAM_DL BIT(12)
+#define UNICAM_PS BIT(13)
+#define UNICAM_IS BIT(14)
+#define UNICAM_PI0 BIT(15)
+#define UNICAM_PI1 BIT(16)
+#define UNICAM_FSI_S BIT(17)
+#define UNICAM_FEI_S BIT(18)
+#define UNICAM_LCI_S BIT(19)
+#define UNICAM_BUF0_RDY BIT(20)
+#define UNICAM_BUF0_NO BIT(21)
+#define UNICAM_BUF1_RDY BIT(22)
+#define UNICAM_BUF1_NO BIT(23)
+#define UNICAM_DI BIT(24)
+
+#define UNICAM_STA_MASK_ALL \
+ (UNICAM_DL + \
+ UNICAM_SBE + \
+ UNICAM_PBE + \
+ UNICAM_HOE + \
+ UNICAM_PLE + \
+ UNICAM_SSC + \
+ UNICAM_CRCE + \
+ UNICAM_IFO + \
+ UNICAM_OFO + \
+ UNICAM_PS + \
+ UNICAM_PI0 + \
+ UNICAM_PI1)
+
+/* UNICAM_ANA Register */
+#define UNICAM_APD BIT(0)
+#define UNICAM_BPD BIT(1)
+#define UNICAM_AR BIT(2)
+#define UNICAM_DDL BIT(3)
+#define UNICAM_CTATADJ_MASK GENMASK(7, 4)
+#define UNICAM_PTATADJ_MASK GENMASK(11, 8)
+
+/* UNICAM_PRI Register */
+#define UNICAM_PE BIT(0)
+#define UNICAM_PT_MASK GENMASK(2, 1)
+#define UNICAM_NP_MASK GENMASK(7, 4)
+#define UNICAM_PP_MASK GENMASK(11, 8)
+#define UNICAM_BS_MASK GENMASK(15, 12)
+#define UNICAM_BL_MASK GENMASK(17, 16)
+
+/* UNICAM_CLK Register */
+#define UNICAM_CLE BIT(0)
+#define UNICAM_CLPD BIT(1)
+#define UNICAM_CLLPE BIT(2)
+#define UNICAM_CLHSE BIT(3)
+#define UNICAM_CLTRE BIT(4)
+#define UNICAM_CLAC_MASK GENMASK(8, 5)
+#define UNICAM_CLSTE BIT(29)
+
+/* UNICAM_CLT Register */
+#define UNICAM_CLT1_MASK GENMASK(7, 0)
+#define UNICAM_CLT2_MASK GENMASK(15, 8)
+
+/* UNICAM_DATn Registers */
+#define UNICAM_DLE BIT(0)
+#define UNICAM_DLPD BIT(1)
+#define UNICAM_DLLPE BIT(2)
+#define UNICAM_DLHSE BIT(3)
+#define UNICAM_DLTRE BIT(4)
+#define UNICAM_DLSM BIT(5)
+#define UNICAM_DLFO BIT(28)
+#define UNICAM_DLSTE BIT(29)
+
+#define UNICAM_DAT_MASK_ALL (UNICAM_DLSTE + UNICAM_DLFO)
+
+/* UNICAM_DLT Register */
+#define UNICAM_DLT1_MASK GENMASK(7, 0)
+#define UNICAM_DLT2_MASK GENMASK(15, 8)
+#define UNICAM_DLT3_MASK GENMASK(23, 16)
+
+/* UNICAM_ICTL Register */
+#define UNICAM_FSIE BIT(0)
+#define UNICAM_FEIE BIT(1)
+#define UNICAM_IBOB BIT(2)
+#define UNICAM_FCM BIT(3)
+#define UNICAM_TFC BIT(4)
+#define UNICAM_LIP_MASK GENMASK(6, 5)
+#define UNICAM_LCIE_MASK GENMASK(28, 16)
+
+/* UNICAM_IDI0/1 Register */
+#define UNICAM_ID0_MASK GENMASK(7, 0)
+#define UNICAM_ID1_MASK GENMASK(15, 8)
+#define UNICAM_ID2_MASK GENMASK(23, 16)
+#define UNICAM_ID3_MASK GENMASK(31, 24)
+
+/* UNICAM_ISTA Register */
+#define UNICAM_FSI BIT(0)
+#define UNICAM_FEI BIT(1)
+#define UNICAM_LCI BIT(2)
+
+#define UNICAM_ISTA_MASK_ALL (UNICAM_FSI + UNICAM_FEI + UNICAM_LCI)
+
+/* UNICAM_IPIPE Register */
+#define UNICAM_PUM_MASK GENMASK(2, 0)
+ /* Unpacking modes */
+ #define UNICAM_PUM_NONE 0
+ #define UNICAM_PUM_UNPACK6 1
+ #define UNICAM_PUM_UNPACK7 2
+ #define UNICAM_PUM_UNPACK8 3
+ #define UNICAM_PUM_UNPACK10 4
+ #define UNICAM_PUM_UNPACK12 5
+ #define UNICAM_PUM_UNPACK14 6
+ #define UNICAM_PUM_UNPACK16 7
+#define UNICAM_DDM_MASK GENMASK(6, 3)
+#define UNICAM_PPM_MASK GENMASK(9, 7)
+ /* Packing modes */
+ #define UNICAM_PPM_NONE 0
+ #define UNICAM_PPM_PACK8 1
+ #define UNICAM_PPM_PACK10 2
+ #define UNICAM_PPM_PACK12 3
+ #define UNICAM_PPM_PACK14 4
+ #define UNICAM_PPM_PACK16 5
+#define UNICAM_DEM_MASK GENMASK(11, 10)
+#define UNICAM_DEBL_MASK GENMASK(14, 12)
+#define UNICAM_ICM_MASK GENMASK(16, 15)
+#define UNICAM_IDM_MASK GENMASK(17, 17)
+
+/* UNICAM_ICC Register */
+#define UNICAM_ICFL_MASK GENMASK(4, 0)
+#define UNICAM_ICFH_MASK GENMASK(9, 5)
+#define UNICAM_ICST_MASK GENMASK(12, 10)
+#define UNICAM_ICLT_MASK GENMASK(15, 13)
+#define UNICAM_ICLL_MASK GENMASK(31, 16)
+
+/* UNICAM_DCS Register */
+#define UNICAM_DIE BIT(0)
+#define UNICAM_DIM BIT(1)
+#define UNICAM_DBOB BIT(3)
+#define UNICAM_FDE BIT(4)
+#define UNICAM_LDP BIT(5)
+#define UNICAM_EDL_MASK GENMASK(15, 8)
+
+/* UNICAM_DBCTL Register */
+#define UNICAM_DBEN BIT(0)
+#define UNICAM_BUF0_IE BIT(1)
+#define UNICAM_BUF1_IE BIT(2)
+
+/* UNICAM_CMP[0,1] register */
+#define UNICAM_PCE BIT(31)
+#define UNICAM_GI BIT(9)
+#define UNICAM_CPH BIT(8)
+#define UNICAM_PCVC_MASK GENMASK(7, 6)
+#define UNICAM_PCDT_MASK GENMASK(5, 0)
+
+/* UNICAM_MISC register */
+#define UNICAM_FL0 BIT(6)
+#define UNICAM_FL1 BIT(9)
+
+#endif