| Message ID | 20220121142904.4091481-12-p.yadav@ti.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | CSI2RX support on J721E | expand |
Hi Pratyush, Thank you for the patch. On Fri, Jan 21, 2022 at 07:59:01PM +0530, Pratyush Yadav wrote: > TI's J721E uses the Cadence CSI2RX and DPHY peripherals to facilitate > capture over a CSI-2 bus. > > The Cadence CSI2RX IP acts as a bridge between the TI specific parts and > the CSI-2 protocol parts. TI then has a wrapper on top of this bridge > called the SHIM layer. It takes in data from stream 0, repacks it, and > sends it to memory over PSI-L DMA. > > This driver acts as the "front end" to V4L2 client applications. It > implements the required ioctls and buffer operations, passes the > necessary calls on to the bridge, programs the SHIM layer, and performs > DMA via the dmaengine API to finally return the data to a buffer > supplied by the application. > > Signed-off-by: Pratyush Yadav <p.yadav@ti.com> > > --- > > (no changes since v5) > > Changes in v5: > - Add dependency on PHY_CADENCE_DPHY_RX instead of PHY_CADENCE_DPHY > since the Rx mode DPHY now has a separate driver. > - Drop ti_csi2rx_validate_pipeline(). Pipeline validation should be done > at media_pipeline_start(). > - Do not assign flags. > - Fix error handling in ti_csi2rx_start_streaming(). Free up vb2 buffers > when media_pipeline_start() fails. > > Changes in v4: > - Acquire the media device's graph_mutex before starting the graph walk. > - Call media_graph_walk_init() and media_graph_walk_cleanup() when > starting and ending the graph walk respectively. > - Reduce max frame height and width in enum_framesizes. Currently they > are set to UINT_MAX but they must be a multiple of step_width, so they > need to be rounded down. Also, these values are absurdly large which > causes some userspace applications like gstreamer to trip up. While it > is not generally right to change the kernel for an application bug, it > is not such a big deal here. This change is replacing one set of > absurdly large arbitrary values with another set of smaller but still > absurdly large arbitrary values. Both limits are unlikely to be hit in > practice. > > Changes in v3: > - Move DMA related fields in struct ti_csi2rx_dma. > - Protect DMA buffer queue with a spinlock to make sure the queue buffer > and DMA callback don't race on it. > - Track the current DMA state. It might go idle because of a lack of > buffers. This state can be used to restart it if needed. > - Do not include the current buffer in the pending queue. It is slightly > better modelling than leaving it at the head of the pending queue. > - Use the buffer as the callback argument, and add a reference to csi in it. > - If queueing a buffer to DMA fails, the buffer gets leaked and DMA gets > stalled with. Instead, report the error to vb2 and queue the next > buffer in the pending queue. > - DMA gets stalled if we run out of buffers since the callback is the > only one that fires subsequent transfers and it is no longer being > called. Check for that when queueing buffers and restart DMA if > needed. > - Do not put of node until we are done using the fwnode. > - Set inital format to UYVY 640x480. > > Changes in v2: > - Use dmaengine_get_dma_device() instead of directly accessing > dma->device->dev. > - Do not set dst_addr_width when configuring slave DMA. > - Move to a separate subdir and rename to j721e-csi2rx.c > - Convert compatible to ti,j721e-csi2rx. > - Move to use Media Controller centric APIs. > - Improve cleanup in probe when one of the steps fails. > - Add colorspace to formats database. > - Set hw_revision on media_device. > - Move video device initialization to probe time instead of register time. > > MAINTAINERS | 6 + > drivers/media/platform/Kconfig | 12 + > drivers/media/platform/ti/Makefile | 1 + > .../media/platform/ti/j721e-csi2rx/Makefile | 2 + > .../platform/ti/j721e-csi2rx/j721e-csi2rx.c | 913 ++++++++++++++++++ > 5 files changed, 934 insertions(+) > create mode 100644 drivers/media/platform/ti/j721e-csi2rx/Makefile > create mode 100644 drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c > > diff --git a/MAINTAINERS b/MAINTAINERS > index 3b8fa4e5047f..2a8ebf17462e 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -19181,6 +19181,12 @@ S: Odd Fixes > F: drivers/clk/ti/ > F: include/linux/clk/ti.h > > +TI J721E CSI2RX DRIVER > +M: Pratyush Yadav <p.yadav@ti.com> > +L: linux-media@vger.kernel.org > +S: Supported > +F: drivers/media/platform/ti/j721e-csi2rx/ > + > TI DAVINCI MACHINE SUPPORT > M: Sekhar Nori <nsekhar@ti.com> > R: Bartosz Golaszewski <brgl@bgdev.pl> > diff --git a/drivers/media/platform/Kconfig b/drivers/media/platform/Kconfig > index 9fbdba0fd1e7..0fa58563d93b 100644 > --- a/drivers/media/platform/Kconfig > +++ b/drivers/media/platform/Kconfig > @@ -216,6 +216,18 @@ config VIDEO_RCAR_ISP > To compile this driver as a module, choose M here: the > module will be called rcar-isp. > > +config VIDEO_TI_J721E_CSI2RX > + tristate "TI J721E CSI2RX wrapper layer driver" > + depends on VIDEO_DEV && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API > + depends on MEDIA_SUPPORT && MEDIA_CONTROLLER > + depends on PHY_CADENCE_DPHY_RX && VIDEO_CADENCE_CSI2RX > + depends on ARCH_K3 || COMPILE_TEST > + select VIDEOBUF2_DMA_CONTIG > + select V4L2_FWNODE > + help > + Support for TI CSI2RX wrapper layer. This just enables the wrapper driver. > + The Cadence CSI2RX bridge driver needs to be enabled separately. > + > endif # V4L_PLATFORM_DRIVERS > > menuconfig V4L_MEM2MEM_DRIVERS > diff --git a/drivers/media/platform/ti/Makefile b/drivers/media/platform/ti/Makefile > index bbc737ccbbea..17c9cfb74f66 100644 > --- a/drivers/media/platform/ti/Makefile > +++ b/drivers/media/platform/ti/Makefile > @@ -1,3 +1,4 @@ > # SPDX-License-Identifier: GPL-2.0 > obj-y += cal/ > obj-y += vpe/ > +obj-y += j721e-csi2rx/ Alphabetical order maybe ? > diff --git a/drivers/media/platform/ti/j721e-csi2rx/Makefile b/drivers/media/platform/ti/j721e-csi2rx/Makefile > new file mode 100644 > index 000000000000..377afc1d6280 > --- /dev/null > +++ b/drivers/media/platform/ti/j721e-csi2rx/Makefile > @@ -0,0 +1,2 @@ > +# SPDX-License-Identifier: GPL-2.0 > +obj-$(CONFIG_VIDEO_TI_J721E_CSI2RX) += j721e-csi2rx.o > diff --git a/drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c b/drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c > new file mode 100644 > index 000000000000..43f31f161f43 > --- /dev/null > +++ b/drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c > @@ -0,0 +1,913 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* > + * TI CSI2 RX driver. > + * > + * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/ > + * > + * Author: Pratyush Yadav <p.yadav@ti.com> > + */ > + > +#include <linux/bitfield.h> > +#include <linux/module.h> > +#include <linux/platform_device.h> > +#include <linux/dmaengine.h> > +#include <linux/of_platform.h> Alphabetical order would be nice here too. > + > +#include <media/v4l2-device.h> > +#include <media/v4l2-ioctl.h> > +#include <media/videobuf2-dma-contig.h> > + > +#define TI_CSI2RX_MODULE_NAME "j721e-csi2rx" > + > +#define SHIM_CNTL 0x10 > +#define SHIM_CNTL_PIX_RST BIT(0) > + > +#define SHIM_DMACNTX 0x20 > +#define SHIM_DMACNTX_EN BIT(31) > +#define SHIM_DMACNTX_YUV422 GENMASK(27, 26) > +#define SHIM_DMACNTX_FMT GENMASK(5, 0) > +#define SHIM_DMACNTX_UYVY 0 > +#define SHIM_DMACNTX_VYUY 1 > +#define SHIM_DMACNTX_YUYV 2 > +#define SHIM_DMACNTX_YVYU 3 > + > +#define SHIM_PSI_CFG0 0x24 > +#define SHIM_PSI_CFG0_SRC_TAG GENMASK(15, 0) > +#define SHIM_PSI_CFG0_DST_TAG GENMASK(31, 15) > + > +#define CSI_DF_YUV420 0x18 > +#define CSI_DF_YUV422 0x1e > +#define CSI_DF_RGB444 0x20 > +#define CSI_DF_RGB888 0x24 https://lore.kernel.org/linux-media/20220123160857.24161-2-laurent.pinchart+renesas@ideasonboard.com/ :-) > + > +#define PSIL_WORD_SIZE_BYTES 16 > +/* > + * There are no hard limits on the width or height. The DMA engine can handle > + * all sizes. The max width and height are arbitrary numbers for this driver. > + * Use 16M * 16M as the arbitrary limit. It is large enough that it is unlikely > + * the limit will be hit in practice. > + */ > +#define MAX_WIDTH_BYTES SZ_16M > +#define MAX_HEIGHT_BYTES SZ_16M > + > +struct ti_csi2rx_fmt { > + u32 fourcc; /* Four character code. */ > + u32 code; /* Mbus code. */ > + enum v4l2_colorspace colorspace; > + u32 csi_df; /* CSI Data format. */ It's called data type in CSI-2, not data format. > + u8 bpp; /* Bits per pixel. */ > +}; > + > +struct ti_csi2rx_buffer { > + /* Common v4l2 buffer. Must be first. */ > + struct vb2_v4l2_buffer vb; > + struct list_head list; > + struct ti_csi2rx_dev *csi; > +}; > + > +enum ti_csi2rx_dma_state { > + TI_CSI2RX_DMA_STOPPED, /* Streaming not started yet. */ > + TI_CSI2RX_DMA_IDLE, /* Streaming but no pending DMA operation. */ > + TI_CSI2RX_DMA_ACTIVE, /* Streaming and pending DMA operation. */ > +}; > + > +struct ti_csi2rx_dma { > + /* Protects all fields in this struct. */ > + spinlock_t lock; > + struct dma_chan *chan; > + /* Buffers queued to the driver, waiting to be processed by DMA. */ > + struct list_head queue; > + enum ti_csi2rx_dma_state state; > + /* > + * Current buffer being processed by DMA. NULL if no buffer is being > + * processed. > + */ > + struct ti_csi2rx_buffer *curr; > +}; > + > +struct ti_csi2rx_dev { > + struct device *dev; > + void __iomem *shim; > + struct v4l2_device v4l2_dev; > + struct video_device vdev; > + struct media_device mdev; > + struct media_pipeline pipe; > + struct media_pad pad; > + struct v4l2_async_notifier notifier; > + struct v4l2_subdev *subdev; > + struct vb2_queue vidq; > + struct mutex mutex; /* To serialize ioctls. */ > + struct v4l2_format v_fmt; > + struct ti_csi2rx_dma dma; > + u32 sequence; > +}; > + > +static const struct ti_csi2rx_fmt formats[] = { > + { > + .fourcc = V4L2_PIX_FMT_YUYV, > + .code = MEDIA_BUS_FMT_YUYV8_2X8, > + .colorspace = V4L2_COLORSPACE_SRGB, > + .csi_df = CSI_DF_YUV422, > + .bpp = 16, > + }, { > + .fourcc = V4L2_PIX_FMT_UYVY, > + .code = MEDIA_BUS_FMT_UYVY8_2X8, > + .colorspace = V4L2_COLORSPACE_SRGB, > + .csi_df = CSI_DF_YUV422, > + .bpp = 16, > + }, { > + .fourcc = V4L2_PIX_FMT_YVYU, > + .code = MEDIA_BUS_FMT_YVYU8_2X8, > + .colorspace = V4L2_COLORSPACE_SRGB, > + .csi_df = CSI_DF_YUV422, > + .bpp = 16, > + }, { > + .fourcc = V4L2_PIX_FMT_VYUY, > + .code = MEDIA_BUS_FMT_VYUY8_2X8, > + .colorspace = V4L2_COLORSPACE_SRGB, > + .csi_df = CSI_DF_YUV422, > + .bpp = 16, > + }, > + > + /* More formats can be supported but they are not listed for now. */ > +}; > + > +static const unsigned int num_formats = ARRAY_SIZE(formats); > + > +/* Forward declaration needed by ti_csi2rx_dma_callback. */ > +static int ti_csi2rx_start_dma(struct ti_csi2rx_dev *csi, > + struct ti_csi2rx_buffer *buf); > + > +static const struct ti_csi2rx_fmt *find_format_by_pix(u32 pixelformat) > +{ > + unsigned int i; > + > + for (i = 0; i < num_formats; i++) { > + if (formats[i].fourcc == pixelformat) > + return &formats[i]; > + } > + > + return NULL; > +} > + > +static void ti_csi2rx_fill_fmt(const struct ti_csi2rx_fmt *csi_fmt, > + struct v4l2_format *v4l2_fmt) > +{ > + struct v4l2_pix_format *pix = &v4l2_fmt->fmt.pix; > + u32 bpl; > + > + v4l2_fmt->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; > + pix->pixelformat = csi_fmt->fourcc; > + pix->colorspace = csi_fmt->colorspace; I'd drop this (and the colorspace field in ti_csi2rx_fmt). This driver doesn't care about colorspaces, it should accept any value set by userspace, which should match the colorspace produced by the source subdev. ti_csi2rx_v4l2_init() will have to set a default colorspace explicitly. > + pix->sizeimage = pix->height * pix->width * (csi_fmt->bpp / 8); > + > + bpl = (pix->width * ALIGN(csi_fmt->bpp, 8)) >> 3; > + pix->bytesperline = ALIGN(bpl, 16); > +} > + > +static int ti_csi2rx_querycap(struct file *file, void *priv, > + struct v4l2_capability *cap) > +{ > + struct ti_csi2rx_dev *csi = video_drvdata(file); > + > + strscpy(cap->driver, TI_CSI2RX_MODULE_NAME, sizeof(cap->driver)); > + strscpy(cap->card, TI_CSI2RX_MODULE_NAME, sizeof(cap->card)); > + > + snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s", > + dev_name(csi->dev)); Depending on which series gets merged, you can drop this line: https://lore.kernel.org/linux-media/20220122163656.168440-1-sakari.ailus@linux.intel.com/ > + return 0; > +} > + > +static int ti_csi2rx_enum_fmt_vid_cap(struct file *file, void *priv, > + struct v4l2_fmtdesc *f) > +{ > + if (f->index >= num_formats) > + return -EINVAL; > + > + memset(f->reserved, 0, sizeof(f->reserved)); > + f->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; > + f->pixelformat = formats[f->index].fourcc; > + > + return 0; > +} > + > +static int ti_csi2rx_g_fmt_vid_cap(struct file *file, void *prov, > + struct v4l2_format *f) > +{ > + struct ti_csi2rx_dev *csi = video_drvdata(file); > + > + *f = csi->v_fmt; > + > + return 0; > +} > + > +static int ti_csi2rx_try_fmt_vid_cap(struct file *file, void *priv, > + struct v4l2_format *f) > +{ > + const struct ti_csi2rx_fmt *fmt; > + > + /* > + * Default to the first format if the requested pixel format code isn't > + * supported. > + */ > + fmt = find_format_by_pix(f->fmt.pix.pixelformat); > + if (!fmt) > + fmt = &formats[0]; > + > + if (f->fmt.pix.field == V4L2_FIELD_ANY) > + f->fmt.pix.field = V4L2_FIELD_NONE; > + > + if (f->fmt.pix.field != V4L2_FIELD_NONE) > + return -EINVAL; You should adjust the field, not return an error, so this can just become /* Interlaced formats are not supported. */ f->fmt.pix.field = V4L2_FIELD_NONE; > + > + ti_csi2rx_fill_fmt(fmt, f); > + > + return 0; > +} > + > +static int ti_csi2rx_s_fmt_vid_cap(struct file *file, void *priv, > + struct v4l2_format *f) > +{ > + struct ti_csi2rx_dev *csi = video_drvdata(file); > + struct vb2_queue *q = &csi->vidq; > + int ret; > + > + if (vb2_is_busy(q)) > + return -EBUSY; > + > + ret = ti_csi2rx_try_fmt_vid_cap(file, priv, f); > + if (ret < 0) > + return ret; > + > + csi->v_fmt = *f; > + > + return 0; > +} > + > +static int ti_csi2rx_enum_framesizes(struct file *file, void *fh, > + struct v4l2_frmsizeenum *fsize) > +{ > + const struct ti_csi2rx_fmt *fmt; > + unsigned int pixels_in_word; > + u8 bpp; > + > + fmt = find_format_by_pix(fsize->pixel_format); > + if (!fmt) > + return -EINVAL; > + > + bpp = ALIGN(fmt->bpp, 8); > + > + /* > + * Number of pixels in one PSI-L word. The transfer happens in multiples > + * of PSI-L word sizes. > + */ > + pixels_in_word = PSIL_WORD_SIZE_BYTES * 8 / bpp; > + > + fsize->type = V4L2_FRMSIZE_TYPE_STEPWISE; > + fsize->stepwise.min_width = pixels_in_word; > + fsize->stepwise.max_width = rounddown(MAX_WIDTH_BYTES, pixels_in_word); > + fsize->stepwise.step_width = pixels_in_word; > + fsize->stepwise.min_height = 1; > + fsize->stepwise.max_height = MAX_HEIGHT_BYTES; > + fsize->stepwise.step_height = 1; > + > + return 0; > +} > + > +static const struct v4l2_ioctl_ops csi_ioctl_ops = { > + .vidioc_querycap = ti_csi2rx_querycap, > + .vidioc_enum_fmt_vid_cap = ti_csi2rx_enum_fmt_vid_cap, > + .vidioc_try_fmt_vid_cap = ti_csi2rx_try_fmt_vid_cap, > + .vidioc_g_fmt_vid_cap = ti_csi2rx_g_fmt_vid_cap, > + .vidioc_s_fmt_vid_cap = ti_csi2rx_s_fmt_vid_cap, > + .vidioc_enum_framesizes = ti_csi2rx_enum_framesizes, > + .vidioc_reqbufs = vb2_ioctl_reqbufs, > + .vidioc_create_bufs = vb2_ioctl_create_bufs, > + .vidioc_prepare_buf = vb2_ioctl_prepare_buf, > + .vidioc_querybuf = vb2_ioctl_querybuf, > + .vidioc_qbuf = vb2_ioctl_qbuf, > + .vidioc_dqbuf = vb2_ioctl_dqbuf, > + .vidioc_expbuf = vb2_ioctl_expbuf, > + .vidioc_streamon = vb2_ioctl_streamon, > + .vidioc_streamoff = vb2_ioctl_streamoff, > +}; > + > +static const struct v4l2_file_operations csi_fops = { > + .owner = THIS_MODULE, > + .open = v4l2_fh_open, > + .release = vb2_fop_release, > + .read = vb2_fop_read, > + .poll = vb2_fop_poll, > + .unlocked_ioctl = video_ioctl2, > + .mmap = vb2_fop_mmap, > +}; > + > +static int ti_csi2rx_video_register(struct ti_csi2rx_dev *csi) > +{ > + struct video_device *vdev = &csi->vdev; > + int ret, src_pad; > + > + ret = video_register_device(vdev, VFL_TYPE_VIDEO, -1); > + if (ret) > + return ret; > + > + src_pad = media_entity_get_fwnode_pad(&csi->subdev->entity, > + csi->subdev->fwnode, > + MEDIA_PAD_FL_SOURCE); > + if (src_pad < 0) { > + dev_err(csi->dev, "Couldn't find source pad for subdev\n"); > + return src_pad; > + } > + > + ret = media_create_pad_link(&csi->subdev->entity, src_pad, > + &vdev->entity, 0, > + MEDIA_LNK_FL_IMMUTABLE | > + MEDIA_LNK_FL_ENABLED); > + if (ret) { > + video_unregister_device(vdev); > + return ret; > + } This can be simplified by using v4l2_create_fwnode_links_to_pad(). > + > + return 0; > +} > + > +static int csi_async_notifier_bound(struct v4l2_async_notifier *notifier, > + struct v4l2_subdev *subdev, > + struct v4l2_async_subdev *asd) > +{ > + struct ti_csi2rx_dev *csi = dev_get_drvdata(notifier->v4l2_dev->dev); > + > + csi->subdev = subdev; > + > + return 0; > +} > + > +static int csi_async_notifier_complete(struct v4l2_async_notifier *notifier) > +{ > + struct ti_csi2rx_dev *csi = dev_get_drvdata(notifier->v4l2_dev->dev); > + int ret; > + > + ret = ti_csi2rx_video_register(csi); I would inline the ti_csi2rx_video_register() function here, it's not large, and it's only called in a single place. > + if (ret) > + return ret; > + > + return v4l2_device_register_subdev_nodes(&csi->v4l2_dev); > +} > + > +static const struct v4l2_async_notifier_operations csi_async_notifier_ops = { > + .bound = csi_async_notifier_bound, > + .complete = csi_async_notifier_complete, > +}; > + > +static int ti_csi2rx_init_subdev(struct ti_csi2rx_dev *csi) > +{ > + struct fwnode_handle *fwnode; > + struct v4l2_async_subdev *asd; > + struct device_node *node; > + int ret; > + > + node = of_get_child_by_name(csi->dev->of_node, "csi-bridge"); > + if (!node) > + return -EINVAL; > + > + fwnode = of_fwnode_handle(node); > + if (!fwnode) { > + of_node_put(node); > + return -EINVAL; > + } > + > + v4l2_async_nf_init(&csi->notifier); > + csi->notifier.ops = &csi_async_notifier_ops; > + > + asd = v4l2_async_nf_add_fwnode(&csi->notifier, fwnode, > + struct v4l2_async_subdev); > + of_node_put(node); > + if (IS_ERR(asd)) { > + v4l2_async_nf_cleanup(&csi->notifier); > + return PTR_ERR(asd); > + } > + > + ret = v4l2_async_nf_register(&csi->v4l2_dev, &csi->notifier); > + if (ret) { > + v4l2_async_nf_cleanup(&csi->notifier); > + return ret; > + } > + > + return 0; > +} > + > +static void ti_csi2rx_setup_shim(struct ti_csi2rx_dev *csi) > +{ > + const struct ti_csi2rx_fmt *fmt; > + unsigned int reg; > + > + fmt = find_format_by_pix(csi->v_fmt.fmt.pix.pixelformat); > + if (!fmt) { > + dev_err(csi->dev, "Unknown format\n"); > + return; > + } > + > + /* De-assert the pixel interface reset. */ > + reg = SHIM_CNTL_PIX_RST; > + writel(reg, csi->shim + SHIM_CNTL); > + > + reg = SHIM_DMACNTX_EN; > + reg |= FIELD_PREP(SHIM_DMACNTX_FMT, fmt->csi_df); > + > + /* > + * Using the values from the documentation gives incorrect ordering for > + * the luma and chroma components. In practice, the "reverse" format > + * gives the correct image. So for example, if the image is in UYVY, the > + * reverse would be YVYU. Are you sure this is an issue in the documentation, not in the implementation of the source subdev ? > + */ > + switch (fmt->fourcc) { > + case V4L2_PIX_FMT_UYVY: > + reg |= FIELD_PREP(SHIM_DMACNTX_YUV422, > + SHIM_DMACNTX_YVYU); > + break; > + case V4L2_PIX_FMT_VYUY: > + reg |= FIELD_PREP(SHIM_DMACNTX_YUV422, > + SHIM_DMACNTX_YUYV); > + break; > + case V4L2_PIX_FMT_YUYV: > + reg |= FIELD_PREP(SHIM_DMACNTX_YUV422, > + SHIM_DMACNTX_VYUY); > + break; > + case V4L2_PIX_FMT_YVYU: > + reg |= FIELD_PREP(SHIM_DMACNTX_YUV422, > + SHIM_DMACNTX_UYVY); > + break; > + default: > + /* Ignore if not YUV 4:2:2 */ > + break; > + } > + > + writel(reg, csi->shim + SHIM_DMACNTX); > + > + reg = FIELD_PREP(SHIM_PSI_CFG0_SRC_TAG, 0) | > + FIELD_PREP(SHIM_PSI_CFG0_DST_TAG, 1); > + writel(reg, csi->shim + SHIM_PSI_CFG0); > +} > + > +static void ti_csi2rx_dma_callback(void *param) > +{ > + struct ti_csi2rx_buffer *buf = param; > + struct ti_csi2rx_dev *csi = buf->csi; > + struct ti_csi2rx_dma *dma = &csi->dma; > + unsigned long flags = 0; No need to initialize flags to 0. > + > + buf->vb.vb2_buf.timestamp = ktime_get_ns(); > + buf->vb.sequence = csi->sequence++; Is there any hardware frame counter that could be used, to detect dropped frames ? Or maybe a SOF hardware interrupt somewhere (either in the SHIM or the CSI-2 receiver) ? > + > + spin_lock_irqsave(&dma->lock, flags); > + > + WARN_ON(dma->curr != buf); > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_DONE); > + > + /* If there are more buffers to process then start their transfer. */ > + dma->curr = NULL; > + while (!list_empty(&dma->queue)) { > + buf = list_entry(dma->queue.next, struct ti_csi2rx_buffer, list); > + list_del(&buf->list); > + > + if (ti_csi2rx_start_dma(csi, buf)) { > + dev_err(csi->dev, "Failed to queue the next buffer for DMA\n"); > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR); If this buffer fails to be queued, do you expect that the next buffer in the list would succeed ? It seems to be a fatal error to me. > + } else { > + dma->curr = buf; > + break; Shouldn't all pending buffers be queued to the DMA engine ? It seems that you're queuing one buffer at a time, which would cause an underrun if the system is too slow to queue the next buffer during vertical blanking. It defeats the point of having multiple buffers in the V4L2 queue. You should instead queue the buffers to the DMA engine as soon as they're received by the driver. > + } > + } > + > + if (!dma->curr) > + dma->state = TI_CSI2RX_DMA_IDLE; > + > + spin_unlock_irqrestore(&dma->lock, flags); > +} > + > +static int ti_csi2rx_start_dma(struct ti_csi2rx_dev *csi, > + struct ti_csi2rx_buffer *buf) > +{ > + unsigned long addr; > + struct dma_async_tx_descriptor *desc; > + size_t len = csi->v_fmt.fmt.pix.sizeimage; > + dma_cookie_t cookie; > + int ret = 0; > + > + addr = vb2_dma_contig_plane_dma_addr(&buf->vb.vb2_buf, 0); > + desc = dmaengine_prep_slave_single(csi->dma.chan, addr, len, > + DMA_DEV_TO_MEM, > + DMA_PREP_INTERRUPT | DMA_CTRL_ACK); > + if (!desc) > + return -EIO; > + > + desc->callback = ti_csi2rx_dma_callback; > + desc->callback_param = buf; > + > + cookie = dmaengine_submit(desc); > + ret = dma_submit_error(cookie); > + if (ret) > + return ret; > + > + dma_async_issue_pending(csi->dma.chan); > + > + return 0; > +} > + > +static int ti_csi2rx_queue_setup(struct vb2_queue *q, unsigned int *nbuffers, > + unsigned int *nplanes, unsigned int sizes[], > + struct device *alloc_devs[]) > +{ > + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(q); > + unsigned int size = csi->v_fmt.fmt.pix.sizeimage; > + > + if (*nplanes) { > + if (sizes[0] < size) > + return -EINVAL; > + size = sizes[0]; > + } > + > + *nplanes = 1; > + sizes[0] = size; > + > + return 0; > +} > + > +static int ti_csi2rx_buffer_prepare(struct vb2_buffer *vb) > +{ > + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(vb->vb2_queue); > + unsigned long size = csi->v_fmt.fmt.pix.sizeimage; > + > + if (vb2_plane_size(vb, 0) < size) { > + dev_err(csi->dev, "Data will not fit into plane\n"); > + return -EINVAL; > + } > + > + vb2_set_plane_payload(vb, 0, size); > + return 0; > +} > + > +static void ti_csi2rx_buffer_queue(struct vb2_buffer *vb) > +{ > + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(vb->vb2_queue); > + struct ti_csi2rx_buffer *buf; > + struct ti_csi2rx_dma *dma = &csi->dma; > + unsigned long flags = 0; > + int ret; > + > + buf = container_of(vb, struct ti_csi2rx_buffer, vb.vb2_buf); > + buf->csi = csi; > + > + spin_lock_irqsave(&dma->lock, flags); > + /* > + * Usually the DMA callback takes care of queueing the pending buffers. > + * But if DMA has stalled due to lack of buffers, restart it now. > + */ > + if (dma->state == TI_CSI2RX_DMA_IDLE) { > + ret = ti_csi2rx_start_dma(csi, buf); > + if (ret) { > + dev_err(csi->dev, "Failed to start DMA: %d\n", ret); > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED); > + goto unlock; > + } > + > + dma->curr = buf; > + dma->state = TI_CSI2RX_DMA_ACTIVE; > + } else { > + list_add_tail(&buf->list, &dma->queue); > + } > + > +unlock: > + spin_unlock_irqrestore(&dma->lock, flags); > +} > + > +static int ti_csi2rx_start_streaming(struct vb2_queue *vq, unsigned int count) > +{ > + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(vq); > + struct ti_csi2rx_dma *dma = &csi->dma; > + struct ti_csi2rx_buffer *buf, *tmp; > + unsigned long flags; > + int ret = 0; > + > + spin_lock_irqsave(&dma->lock, flags); > + if (list_empty(&dma->queue)) > + ret = -EIO; > + spin_unlock_irqrestore(&dma->lock, flags); > + if (ret) > + return ret; > + > + ret = media_pipeline_start(&csi->vdev.entity, &csi->pipe); > + if (ret) > + goto err; > + > + ti_csi2rx_setup_shim(csi); > + > + ret = v4l2_subdev_call(csi->subdev, video, s_stream, 1); > + if (ret) > + goto err_pipeline; > + > + csi->sequence = 0; > + > + spin_lock_irqsave(&dma->lock, flags); > + buf = list_entry(dma->queue.next, struct ti_csi2rx_buffer, list); > + list_del(&buf->list); > + dma->state = TI_CSI2RX_DMA_ACTIVE; > + > + ret = ti_csi2rx_start_dma(csi, buf); Shouldn't you start DMA before starting the source subdev ? You may miss the first frame otherwise. > + if (ret) { > + dev_err(csi->dev, "Failed to start DMA: %d\n", ret); > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED); > + spin_unlock_irqrestore(&dma->lock, flags); > + goto err_stream; > + } > + > + dma->curr = buf; > + spin_unlock_irqrestore(&dma->lock, flags); > + > + return 0; > + > +err_stream: > + v4l2_subdev_call(csi->subdev, video, s_stream, 0); > +err_pipeline: > + media_pipeline_stop(&csi->vdev.entity); > +err: > + spin_lock_irqsave(&dma->lock, flags); > + list_for_each_entry_safe(buf, tmp, &dma->queue, list) { > + list_del(&buf->list); > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED); > + } > + csi->dma.state = TI_CSI2RX_DMA_STOPPED; > + spin_unlock_irqrestore(&dma->lock, flags); > + > + return ret; > +} > + > +static void ti_csi2rx_stop_streaming(struct vb2_queue *vq) > +{ > + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(vq); > + struct ti_csi2rx_buffer *buf = NULL, *tmp; > + struct ti_csi2rx_dma *dma = &csi->dma; > + unsigned long flags = 0; > + int ret; > + > + media_pipeline_stop(&csi->vdev.entity); > + > + ret = v4l2_subdev_call(csi->subdev, video, s_stream, 0); > + if (ret) > + dev_err(csi->dev, "Failed to stop subdev stream\n"); > + > + writel(0, csi->shim + SHIM_CNTL); > + > + ret = dmaengine_terminate_sync(csi->dma.chan); > + if (ret) > + dev_err(csi->dev, "Failed to stop DMA\n"); > + > + writel(0, csi->shim + SHIM_DMACNTX); > + Code from here... > + spin_lock_irqsave(&dma->lock, flags); > + list_for_each_entry_safe(buf, tmp, &csi->dma.queue, list) { > + list_del(&buf->list); > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR); > + } > + > + if (dma->curr) > + vb2_buffer_done(&dma->curr->vb.vb2_buf, VB2_BUF_STATE_ERROR); > + > + dma->curr = NULL; ... to here could be moved to a separate function that takes a VB2 buf state parameter, to be also used in the error path of ti_csi2rx_start_streaming(). > + dma->state = TI_CSI2RX_DMA_STOPPED; > + spin_unlock_irqrestore(&dma->lock, flags); > +} > + > +static const struct vb2_ops csi_vb2_qops = { > + .queue_setup = ti_csi2rx_queue_setup, > + .buf_prepare = ti_csi2rx_buffer_prepare, > + .buf_queue = ti_csi2rx_buffer_queue, > + .start_streaming = ti_csi2rx_start_streaming, > + .stop_streaming = ti_csi2rx_stop_streaming, > + .wait_prepare = vb2_ops_wait_prepare, > + .wait_finish = vb2_ops_wait_finish, > +}; > + > +static int ti_csi2rx_init_vb2q(struct ti_csi2rx_dev *csi) > +{ > + struct vb2_queue *q = &csi->vidq; > + int ret; > + > + q->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; > + q->io_modes = VB2_MMAP | VB2_USERPTR | VB2_DMABUF | VB2_READ; Usage of USERPTR and READ is not recommended, I'd drop them from the driver. > + q->drv_priv = csi; > + q->buf_struct_size = sizeof(struct ti_csi2rx_buffer); > + q->ops = &csi_vb2_qops; > + q->mem_ops = &vb2_dma_contig_memops; > + q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC; > + q->dev = dmaengine_get_dma_device(csi->dma.chan); That's interesting, why do you use the dmaengine device and not csi->dev ? > + q->lock = &csi->mutex; > + > + ret = vb2_queue_init(q); > + if (ret) > + return ret; > + > + csi->vdev.queue = q; > + > + return 0; > +} > + > +static int ti_csi2rx_init_dma(struct ti_csi2rx_dev *csi) > +{ > + struct dma_slave_config cfg; struct dma_slave_config cfg = { }; and you can drop the memset below. Or possibly even better, struct dma_slave_config cfg = { .src_addr_with = DMA_SLAVE_BUSWIDTH_16_BYTES, }; > + int ret; > + > + INIT_LIST_HEAD(&csi->dma.queue); > + spin_lock_init(&csi->dma.lock); > + > + csi->dma.state = TI_CSI2RX_DMA_STOPPED; > + > + csi->dma.chan = dma_request_chan(csi->dev, "rx0"); > + if (IS_ERR(csi->dma.chan)) > + return PTR_ERR(csi->dma.chan); > + > + memset(&cfg, 0, sizeof(cfg)); > + > + cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_16_BYTES; > + > + ret = dmaengine_slave_config(csi->dma.chan, &cfg); > + if (ret) > + return ret; > + > + return 0; > +} > + > +static int ti_csi2rx_v4l2_init(struct ti_csi2rx_dev *csi) > +{ > + struct media_device *mdev = &csi->mdev; > + struct video_device *vdev = &csi->vdev; > + const struct ti_csi2rx_fmt *fmt; > + struct v4l2_pix_format *pix_fmt = &csi->v_fmt.fmt.pix; > + int ret; > + > + fmt = find_format_by_pix(V4L2_PIX_FMT_UYVY); > + if (!fmt) > + return -EINVAL; > + > + pix_fmt->width = 640; > + pix_fmt->height = 480; Should you initialize ->field too ? > + > + ti_csi2rx_fill_fmt(fmt, &csi->v_fmt); > + > + mdev->dev = csi->dev; > + mdev->hw_revision = 1; > + strscpy(mdev->model, "TI-CSI2RX", sizeof(mdev->model)); > + snprintf(mdev->bus_info, sizeof(mdev->bus_info), "platform:%s", > + dev_name(mdev->dev)); > + > + media_device_init(mdev); > + > + strscpy(vdev->name, TI_CSI2RX_MODULE_NAME, sizeof(vdev->name)); > + vdev->v4l2_dev = &csi->v4l2_dev; > + vdev->vfl_dir = VFL_DIR_RX; > + vdev->fops = &csi_fops; > + vdev->ioctl_ops = &csi_ioctl_ops; > + vdev->release = video_device_release_empty; > + vdev->device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_READWRITE | You can also drop V4L2_CAP_READWRITE if you drop VB2_READ above. > + V4L2_CAP_STREAMING | V4L2_CAP_IO_MC; > + vdev->lock = &csi->mutex; > + video_set_drvdata(vdev, csi); > + > + csi->pad.flags = MEDIA_PAD_FL_SINK; > + ret = media_entity_pads_init(&csi->vdev.entity, 1, &csi->pad); > + if (ret) > + return ret; > + > + csi->v4l2_dev.mdev = mdev; > + > + ret = v4l2_device_register(csi->dev, &csi->v4l2_dev); > + if (ret) > + return ret; > + > + ret = media_device_register(mdev); > + if (ret) { > + v4l2_device_unregister(&csi->v4l2_dev); > + media_device_cleanup(mdev); > + return ret; > + } > + > + return 0; > +} > + > +static void ti_csi2rx_cleanup_dma(struct ti_csi2rx_dev *csi) > +{ > + dma_release_channel(csi->dma.chan); > +} > + > +static void ti_csi2rx_cleanup_v4l2(struct ti_csi2rx_dev *csi) > +{ > + media_device_unregister(&csi->mdev); > + v4l2_device_unregister(&csi->v4l2_dev); > + media_device_cleanup(&csi->mdev); > +} > + > +static void ti_csi2rx_cleanup_subdev(struct ti_csi2rx_dev *csi) > +{ > + v4l2_async_nf_unregister(&csi->notifier); > + v4l2_async_nf_cleanup(&csi->notifier); > +} > + > +static void ti_csi2rx_cleanup_vb2q(struct ti_csi2rx_dev *csi) > +{ > + vb2_queue_release(&csi->vidq); > +} > + > +static int ti_csi2rx_probe(struct platform_device *pdev) > +{ > + struct ti_csi2rx_dev *csi; > + struct resource *res; > + int ret; > + > + csi = devm_kzalloc(&pdev->dev, sizeof(*csi), GFP_KERNEL); Don't use devm_kzalloc() here (see the explanation in the remove function). > + if (!csi) > + return -ENOMEM; > + > + csi->dev = &pdev->dev; > + platform_set_drvdata(pdev, csi); > + > + mutex_init(&csi->mutex); > + > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > + csi->shim = devm_ioremap_resource(&pdev->dev, res); > + if (IS_ERR(csi->shim)) > + return PTR_ERR(csi->shim); > + > + ret = ti_csi2rx_init_dma(csi); > + if (ret) > + return ret; > + > + ret = ti_csi2rx_v4l2_init(csi); > + if (ret) > + goto err_dma; > + > + ret = ti_csi2rx_init_vb2q(csi); > + if (ret) > + goto err_v4l2; > + > + ret = ti_csi2rx_init_subdev(csi); > + if (ret) > + goto err_vb2q; > + > + ret = of_platform_populate(csi->dev->of_node, NULL, NULL, csi->dev); > + if (ret) { > + dev_err(csi->dev, "Failed to create children: %d\n", ret); > + goto err_subdev; > + } > + > + return 0; > + > +err_subdev: > + ti_csi2rx_cleanup_subdev(csi); > +err_vb2q: > + ti_csi2rx_cleanup_vb2q(csi); > +err_v4l2: > + ti_csi2rx_cleanup_v4l2(csi); > +err_dma: > + ti_csi2rx_cleanup_dma(csi); > + return ret; > +} > + > +static int ti_csi2rx_remove(struct platform_device *pdev) > +{ > + struct ti_csi2rx_dev *csi = platform_get_drvdata(pdev); > + > + if (vb2_is_busy(&csi->vidq)) > + return -EBUSY; That's not right, capture should instead be stopped. The right way to handle this is to call all the unregister functions here, but not the cleanup functions, and to implement a real vdev->release handler that will perform all the cleanup and kfree() the ti_csi2rx_dev. > + > + video_unregister_device(&csi->vdev); > + > + ti_csi2rx_cleanup_vb2q(csi); > + ti_csi2rx_cleanup_subdev(csi); > + ti_csi2rx_cleanup_v4l2(csi); > + ti_csi2rx_cleanup_dma(csi); > + > + return 0; > +} > + > +static const struct of_device_id ti_csi2rx_of_match[] = { > + { .compatible = "ti,j721e-csi2rx", }, > + { }, > +}; > +MODULE_DEVICE_TABLE(of, ti_csi2rx_of_match); > + > +static struct platform_driver ti_csi2rx_pdrv = { > + .probe = ti_csi2rx_probe, > + .remove = ti_csi2rx_remove, > + .driver = { > + .name = TI_CSI2RX_MODULE_NAME, > + .of_match_table = ti_csi2rx_of_match, > + }, > +}; > + > +module_platform_driver(ti_csi2rx_pdrv); > + > +MODULE_DESCRIPTION("TI J721E CSI2 RX Driver"); > +MODULE_AUTHOR("Pratyush Yadav <p.yadav@ti.com>"); > +MODULE_LICENSE("GPL v2"); > +MODULE_VERSION("1.0"); I'd drop the version, it will never change, so it's quite pointless. If userspace needs to know if the driver implements a particular feature or includes a bug fix, it can use the kernel version.
Hi Pratyush, On Fri, Jan 21, 2022 at 07:59:01PM +0530, Pratyush Yadav wrote: > TI's J721E uses the Cadence CSI2RX and DPHY peripherals to facilitate > capture over a CSI-2 bus. > > The Cadence CSI2RX IP acts as a bridge between the TI specific parts and > the CSI-2 protocol parts. TI then has a wrapper on top of this bridge > called the SHIM layer. It takes in data from stream 0, repacks it, and > sends it to memory over PSI-L DMA. > > This driver acts as the "front end" to V4L2 client applications. It > implements the required ioctls and buffer operations, passes the > necessary calls on to the bridge, programs the SHIM layer, and performs > DMA via the dmaengine API to finally return the data to a buffer > supplied by the application. > > Signed-off-by: Pratyush Yadav <p.yadav@ti.com> > > --- > > (no changes since v5) > > Changes in v5: > - Add dependency on PHY_CADENCE_DPHY_RX instead of PHY_CADENCE_DPHY > since the Rx mode DPHY now has a separate driver. > - Drop ti_csi2rx_validate_pipeline(). Pipeline validation should be done > at media_pipeline_start(). > - Do not assign flags. > - Fix error handling in ti_csi2rx_start_streaming(). Free up vb2 buffers > when media_pipeline_start() fails. > > Changes in v4: > - Acquire the media device's graph_mutex before starting the graph walk. > - Call media_graph_walk_init() and media_graph_walk_cleanup() when > starting and ending the graph walk respectively. > - Reduce max frame height and width in enum_framesizes. Currently they > are set to UINT_MAX but they must be a multiple of step_width, so they > need to be rounded down. Also, these values are absurdly large which > causes some userspace applications like gstreamer to trip up. While it > is not generally right to change the kernel for an application bug, it > is not such a big deal here. This change is replacing one set of > absurdly large arbitrary values with another set of smaller but still > absurdly large arbitrary values. Both limits are unlikely to be hit in > practice. > > Changes in v3: > - Move DMA related fields in struct ti_csi2rx_dma. > - Protect DMA buffer queue with a spinlock to make sure the queue buffer > and DMA callback don't race on it. > - Track the current DMA state. It might go idle because of a lack of > buffers. This state can be used to restart it if needed. > - Do not include the current buffer in the pending queue. It is slightly > better modelling than leaving it at the head of the pending queue. > - Use the buffer as the callback argument, and add a reference to csi in it. > - If queueing a buffer to DMA fails, the buffer gets leaked and DMA gets > stalled with. Instead, report the error to vb2 and queue the next > buffer in the pending queue. > - DMA gets stalled if we run out of buffers since the callback is the > only one that fires subsequent transfers and it is no longer being > called. Check for that when queueing buffers and restart DMA if > needed. > - Do not put of node until we are done using the fwnode. > - Set inital format to UYVY 640x480. > > Changes in v2: > - Use dmaengine_get_dma_device() instead of directly accessing > dma->device->dev. > - Do not set dst_addr_width when configuring slave DMA. > - Move to a separate subdir and rename to j721e-csi2rx.c > - Convert compatible to ti,j721e-csi2rx. > - Move to use Media Controller centric APIs. > - Improve cleanup in probe when one of the steps fails. > - Add colorspace to formats database. > - Set hw_revision on media_device. > - Move video device initialization to probe time instead of register time. > > MAINTAINERS | 6 + > drivers/media/platform/Kconfig | 12 + > drivers/media/platform/ti/Makefile | 1 + > .../media/platform/ti/j721e-csi2rx/Makefile | 2 + > .../platform/ti/j721e-csi2rx/j721e-csi2rx.c | 913 ++++++++++++++++++ > 5 files changed, 934 insertions(+) > create mode 100644 drivers/media/platform/ti/j721e-csi2rx/Makefile > create mode 100644 drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c > > diff --git a/MAINTAINERS b/MAINTAINERS > index 3b8fa4e5047f..2a8ebf17462e 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -19181,6 +19181,12 @@ S: Odd Fixes > F: drivers/clk/ti/ > F: include/linux/clk/ti.h > > +TI J721E CSI2RX DRIVER > +M: Pratyush Yadav <p.yadav@ti.com> > +L: linux-media@vger.kernel.org > +S: Supported > +F: drivers/media/platform/ti/j721e-csi2rx/ > + > TI DAVINCI MACHINE SUPPORT > M: Sekhar Nori <nsekhar@ti.com> > R: Bartosz Golaszewski <brgl@bgdev.pl> > diff --git a/drivers/media/platform/Kconfig b/drivers/media/platform/Kconfig > index 9fbdba0fd1e7..0fa58563d93b 100644 > --- a/drivers/media/platform/Kconfig > +++ b/drivers/media/platform/Kconfig > @@ -216,6 +216,18 @@ config VIDEO_RCAR_ISP > To compile this driver as a module, choose M here: the > module will be called rcar-isp. > > +config VIDEO_TI_J721E_CSI2RX > + tristate "TI J721E CSI2RX wrapper layer driver" > + depends on VIDEO_DEV && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API > + depends on MEDIA_SUPPORT && MEDIA_CONTROLLER > + depends on PHY_CADENCE_DPHY_RX && VIDEO_CADENCE_CSI2RX > + depends on ARCH_K3 || COMPILE_TEST > + select VIDEOBUF2_DMA_CONTIG > + select V4L2_FWNODE > + help > + Support for TI CSI2RX wrapper layer. This just enables the wrapper driver. > + The Cadence CSI2RX bridge driver needs to be enabled separately. > + > endif # V4L_PLATFORM_DRIVERS > > menuconfig V4L_MEM2MEM_DRIVERS > diff --git a/drivers/media/platform/ti/Makefile b/drivers/media/platform/ti/Makefile > index bbc737ccbbea..17c9cfb74f66 100644 > --- a/drivers/media/platform/ti/Makefile > +++ b/drivers/media/platform/ti/Makefile > @@ -1,3 +1,4 @@ > # SPDX-License-Identifier: GPL-2.0 > obj-y += cal/ > obj-y += vpe/ > +obj-y += j721e-csi2rx/ > diff --git a/drivers/media/platform/ti/j721e-csi2rx/Makefile b/drivers/media/platform/ti/j721e-csi2rx/Makefile > new file mode 100644 > index 000000000000..377afc1d6280 > --- /dev/null > +++ b/drivers/media/platform/ti/j721e-csi2rx/Makefile > @@ -0,0 +1,2 @@ > +# SPDX-License-Identifier: GPL-2.0 > +obj-$(CONFIG_VIDEO_TI_J721E_CSI2RX) += j721e-csi2rx.o > diff --git a/drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c b/drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c > new file mode 100644 > index 000000000000..43f31f161f43 > --- /dev/null > +++ b/drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c > @@ -0,0 +1,913 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* > + * TI CSI2 RX driver. > + * > + * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/ > + * > + * Author: Pratyush Yadav <p.yadav@ti.com> > + */ > + > +#include <linux/bitfield.h> > +#include <linux/module.h> > +#include <linux/platform_device.h> > +#include <linux/dmaengine.h> > +#include <linux/of_platform.h> > + > +#include <media/v4l2-device.h> > +#include <media/v4l2-ioctl.h> > +#include <media/videobuf2-dma-contig.h> > + > +#define TI_CSI2RX_MODULE_NAME "j721e-csi2rx" > + > +#define SHIM_CNTL 0x10 > +#define SHIM_CNTL_PIX_RST BIT(0) > + > +#define SHIM_DMACNTX 0x20 > +#define SHIM_DMACNTX_EN BIT(31) > +#define SHIM_DMACNTX_YUV422 GENMASK(27, 26) > +#define SHIM_DMACNTX_FMT GENMASK(5, 0) > +#define SHIM_DMACNTX_UYVY 0 > +#define SHIM_DMACNTX_VYUY 1 > +#define SHIM_DMACNTX_YUYV 2 > +#define SHIM_DMACNTX_YVYU 3 > + > +#define SHIM_PSI_CFG0 0x24 > +#define SHIM_PSI_CFG0_SRC_TAG GENMASK(15, 0) > +#define SHIM_PSI_CFG0_DST_TAG GENMASK(31, 15) > + > +#define CSI_DF_YUV420 0x18 > +#define CSI_DF_YUV422 0x1e > +#define CSI_DF_RGB444 0x20 > +#define CSI_DF_RGB888 0x24 > + > +#define PSIL_WORD_SIZE_BYTES 16 > +/* > + * There are no hard limits on the width or height. The DMA engine can handle > + * all sizes. The max width and height are arbitrary numbers for this driver. > + * Use 16M * 16M as the arbitrary limit. It is large enough that it is unlikely > + * the limit will be hit in practice. > + */ > +#define MAX_WIDTH_BYTES SZ_16M > +#define MAX_HEIGHT_BYTES SZ_16M > + > +struct ti_csi2rx_fmt { > + u32 fourcc; /* Four character code. */ > + u32 code; /* Mbus code. */ > + enum v4l2_colorspace colorspace; > + u32 csi_df; /* CSI Data format. */ > + u8 bpp; /* Bits per pixel. */ > +}; > + > +struct ti_csi2rx_buffer { > + /* Common v4l2 buffer. Must be first. */ > + struct vb2_v4l2_buffer vb; > + struct list_head list; > + struct ti_csi2rx_dev *csi; > +}; > + > +enum ti_csi2rx_dma_state { > + TI_CSI2RX_DMA_STOPPED, /* Streaming not started yet. */ > + TI_CSI2RX_DMA_IDLE, /* Streaming but no pending DMA operation. */ > + TI_CSI2RX_DMA_ACTIVE, /* Streaming and pending DMA operation. */ > +}; > + > +struct ti_csi2rx_dma { > + /* Protects all fields in this struct. */ > + spinlock_t lock; > + struct dma_chan *chan; > + /* Buffers queued to the driver, waiting to be processed by DMA. */ > + struct list_head queue; > + enum ti_csi2rx_dma_state state; > + /* > + * Current buffer being processed by DMA. NULL if no buffer is being > + * processed. > + */ > + struct ti_csi2rx_buffer *curr; > +}; > + > +struct ti_csi2rx_dev { > + struct device *dev; > + void __iomem *shim; > + struct v4l2_device v4l2_dev; > + struct video_device vdev; > + struct media_device mdev; > + struct media_pipeline pipe; > + struct media_pad pad; > + struct v4l2_async_notifier notifier; > + struct v4l2_subdev *subdev; > + struct vb2_queue vidq; > + struct mutex mutex; /* To serialize ioctls. */ > + struct v4l2_format v_fmt; > + struct ti_csi2rx_dma dma; > + u32 sequence; > +}; > + > +static const struct ti_csi2rx_fmt formats[] = { > + { > + .fourcc = V4L2_PIX_FMT_YUYV, > + .code = MEDIA_BUS_FMT_YUYV8_2X8, > + .colorspace = V4L2_COLORSPACE_SRGB, > + .csi_df = CSI_DF_YUV422, > + .bpp = 16, > + }, { > + .fourcc = V4L2_PIX_FMT_UYVY, > + .code = MEDIA_BUS_FMT_UYVY8_2X8, > + .colorspace = V4L2_COLORSPACE_SRGB, > + .csi_df = CSI_DF_YUV422, > + .bpp = 16, > + }, { > + .fourcc = V4L2_PIX_FMT_YVYU, > + .code = MEDIA_BUS_FMT_YVYU8_2X8, > + .colorspace = V4L2_COLORSPACE_SRGB, > + .csi_df = CSI_DF_YUV422, > + .bpp = 16, > + }, { > + .fourcc = V4L2_PIX_FMT_VYUY, > + .code = MEDIA_BUS_FMT_VYUY8_2X8, > + .colorspace = V4L2_COLORSPACE_SRGB, > + .csi_df = CSI_DF_YUV422, > + .bpp = 16, > + }, > + > + /* More formats can be supported but they are not listed for now. */ > +}; > + > +static const unsigned int num_formats = ARRAY_SIZE(formats); > + > +/* Forward declaration needed by ti_csi2rx_dma_callback. */ > +static int ti_csi2rx_start_dma(struct ti_csi2rx_dev *csi, > + struct ti_csi2rx_buffer *buf); > + > +static const struct ti_csi2rx_fmt *find_format_by_pix(u32 pixelformat) > +{ > + unsigned int i; > + > + for (i = 0; i < num_formats; i++) { > + if (formats[i].fourcc == pixelformat) > + return &formats[i]; > + } > + > + return NULL; > +} > + > +static void ti_csi2rx_fill_fmt(const struct ti_csi2rx_fmt *csi_fmt, > + struct v4l2_format *v4l2_fmt) > +{ > + struct v4l2_pix_format *pix = &v4l2_fmt->fmt.pix; > + u32 bpl; > + > + v4l2_fmt->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; > + pix->pixelformat = csi_fmt->fourcc; > + pix->colorspace = csi_fmt->colorspace; > + pix->sizeimage = pix->height * pix->width * (csi_fmt->bpp / 8); This can overflow. Width and height also aren't checked for the same limits (including step) you have in enum_framesizes. > + > + bpl = (pix->width * ALIGN(csi_fmt->bpp, 8)) >> 3; > + pix->bytesperline = ALIGN(bpl, 16); > +} > + > +static int ti_csi2rx_querycap(struct file *file, void *priv, > + struct v4l2_capability *cap) > +{ > + struct ti_csi2rx_dev *csi = video_drvdata(file); > + > + strscpy(cap->driver, TI_CSI2RX_MODULE_NAME, sizeof(cap->driver)); > + strscpy(cap->card, TI_CSI2RX_MODULE_NAME, sizeof(cap->card)); > + > + snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s", > + dev_name(csi->dev)); > + > + return 0; > +} > + > +static int ti_csi2rx_enum_fmt_vid_cap(struct file *file, void *priv, > + struct v4l2_fmtdesc *f) > +{ > + if (f->index >= num_formats) > + return -EINVAL; > + > + memset(f->reserved, 0, sizeof(f->reserved)); > + f->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; > + f->pixelformat = formats[f->index].fourcc; > + > + return 0; > +} > + > +static int ti_csi2rx_g_fmt_vid_cap(struct file *file, void *prov, > + struct v4l2_format *f) > +{ > + struct ti_csi2rx_dev *csi = video_drvdata(file); > + > + *f = csi->v_fmt; > + > + return 0; > +} > + > +static int ti_csi2rx_try_fmt_vid_cap(struct file *file, void *priv, > + struct v4l2_format *f) > +{ > + const struct ti_csi2rx_fmt *fmt; > + > + /* > + * Default to the first format if the requested pixel format code isn't > + * supported. > + */ > + fmt = find_format_by_pix(f->fmt.pix.pixelformat); > + if (!fmt) > + fmt = &formats[0]; > + > + if (f->fmt.pix.field == V4L2_FIELD_ANY) > + f->fmt.pix.field = V4L2_FIELD_NONE; > + > + if (f->fmt.pix.field != V4L2_FIELD_NONE) > + return -EINVAL; > + > + ti_csi2rx_fill_fmt(fmt, f); > + > + return 0; > +} > + > +static int ti_csi2rx_s_fmt_vid_cap(struct file *file, void *priv, > + struct v4l2_format *f) > +{ > + struct ti_csi2rx_dev *csi = video_drvdata(file); > + struct vb2_queue *q = &csi->vidq; > + int ret; > + > + if (vb2_is_busy(q)) > + return -EBUSY; > + > + ret = ti_csi2rx_try_fmt_vid_cap(file, priv, f); > + if (ret < 0) > + return ret; > + > + csi->v_fmt = *f; > + > + return 0; > +} > + > +static int ti_csi2rx_enum_framesizes(struct file *file, void *fh, > + struct v4l2_frmsizeenum *fsize) > +{ > + const struct ti_csi2rx_fmt *fmt; > + unsigned int pixels_in_word; > + u8 bpp; > + > + fmt = find_format_by_pix(fsize->pixel_format); > + if (!fmt) > + return -EINVAL; > + > + bpp = ALIGN(fmt->bpp, 8); > + > + /* > + * Number of pixels in one PSI-L word. The transfer happens in multiples > + * of PSI-L word sizes. > + */ > + pixels_in_word = PSIL_WORD_SIZE_BYTES * 8 / bpp; > + > + fsize->type = V4L2_FRMSIZE_TYPE_STEPWISE; > + fsize->stepwise.min_width = pixels_in_word; > + fsize->stepwise.max_width = rounddown(MAX_WIDTH_BYTES, pixels_in_word); > + fsize->stepwise.step_width = pixels_in_word; > + fsize->stepwise.min_height = 1; > + fsize->stepwise.max_height = MAX_HEIGHT_BYTES; > + fsize->stepwise.step_height = 1; > + > + return 0; > +} > + > +static const struct v4l2_ioctl_ops csi_ioctl_ops = { > + .vidioc_querycap = ti_csi2rx_querycap, > + .vidioc_enum_fmt_vid_cap = ti_csi2rx_enum_fmt_vid_cap, > + .vidioc_try_fmt_vid_cap = ti_csi2rx_try_fmt_vid_cap, > + .vidioc_g_fmt_vid_cap = ti_csi2rx_g_fmt_vid_cap, > + .vidioc_s_fmt_vid_cap = ti_csi2rx_s_fmt_vid_cap, > + .vidioc_enum_framesizes = ti_csi2rx_enum_framesizes, > + .vidioc_reqbufs = vb2_ioctl_reqbufs, > + .vidioc_create_bufs = vb2_ioctl_create_bufs, > + .vidioc_prepare_buf = vb2_ioctl_prepare_buf, > + .vidioc_querybuf = vb2_ioctl_querybuf, > + .vidioc_qbuf = vb2_ioctl_qbuf, > + .vidioc_dqbuf = vb2_ioctl_dqbuf, > + .vidioc_expbuf = vb2_ioctl_expbuf, > + .vidioc_streamon = vb2_ioctl_streamon, > + .vidioc_streamoff = vb2_ioctl_streamoff, > +}; > + > +static const struct v4l2_file_operations csi_fops = { > + .owner = THIS_MODULE, > + .open = v4l2_fh_open, > + .release = vb2_fop_release, > + .read = vb2_fop_read, > + .poll = vb2_fop_poll, > + .unlocked_ioctl = video_ioctl2, > + .mmap = vb2_fop_mmap, > +}; > + > +static int ti_csi2rx_video_register(struct ti_csi2rx_dev *csi) > +{ > + struct video_device *vdev = &csi->vdev; > + int ret, src_pad; > + > + ret = video_register_device(vdev, VFL_TYPE_VIDEO, -1); > + if (ret) > + return ret; > + > + src_pad = media_entity_get_fwnode_pad(&csi->subdev->entity, > + csi->subdev->fwnode, > + MEDIA_PAD_FL_SOURCE); > + if (src_pad < 0) { > + dev_err(csi->dev, "Couldn't find source pad for subdev\n"); > + return src_pad; > + } > + > + ret = media_create_pad_link(&csi->subdev->entity, src_pad, > + &vdev->entity, 0, > + MEDIA_LNK_FL_IMMUTABLE | > + MEDIA_LNK_FL_ENABLED); > + if (ret) { > + video_unregister_device(vdev); > + return ret; > + } > + > + return 0; > +} > + > +static int csi_async_notifier_bound(struct v4l2_async_notifier *notifier, > + struct v4l2_subdev *subdev, > + struct v4l2_async_subdev *asd) > +{ > + struct ti_csi2rx_dev *csi = dev_get_drvdata(notifier->v4l2_dev->dev); > + > + csi->subdev = subdev; > + > + return 0; > +} > + > +static int csi_async_notifier_complete(struct v4l2_async_notifier *notifier) > +{ > + struct ti_csi2rx_dev *csi = dev_get_drvdata(notifier->v4l2_dev->dev); > + int ret; > + > + ret = ti_csi2rx_video_register(csi); > + if (ret) > + return ret; > + > + return v4l2_device_register_subdev_nodes(&csi->v4l2_dev); > +} > + > +static const struct v4l2_async_notifier_operations csi_async_notifier_ops = { > + .bound = csi_async_notifier_bound, > + .complete = csi_async_notifier_complete, > +}; > + > +static int ti_csi2rx_init_subdev(struct ti_csi2rx_dev *csi) > +{ > + struct fwnode_handle *fwnode; > + struct v4l2_async_subdev *asd; > + struct device_node *node; > + int ret; > + > + node = of_get_child_by_name(csi->dev->of_node, "csi-bridge"); > + if (!node) > + return -EINVAL; > + > + fwnode = of_fwnode_handle(node); > + if (!fwnode) { > + of_node_put(node); > + return -EINVAL; > + } > + > + v4l2_async_nf_init(&csi->notifier); > + csi->notifier.ops = &csi_async_notifier_ops; > + > + asd = v4l2_async_nf_add_fwnode(&csi->notifier, fwnode, > + struct v4l2_async_subdev); > + of_node_put(node); > + if (IS_ERR(asd)) { > + v4l2_async_nf_cleanup(&csi->notifier); > + return PTR_ERR(asd); > + } > + > + ret = v4l2_async_nf_register(&csi->v4l2_dev, &csi->notifier); > + if (ret) { > + v4l2_async_nf_cleanup(&csi->notifier); > + return ret; > + } > + > + return 0; > +} > + > +static void ti_csi2rx_setup_shim(struct ti_csi2rx_dev *csi) > +{ > + const struct ti_csi2rx_fmt *fmt; > + unsigned int reg; > + > + fmt = find_format_by_pix(csi->v_fmt.fmt.pix.pixelformat); > + if (!fmt) { > + dev_err(csi->dev, "Unknown format\n"); > + return; > + } > + > + /* De-assert the pixel interface reset. */ > + reg = SHIM_CNTL_PIX_RST; > + writel(reg, csi->shim + SHIM_CNTL); > + > + reg = SHIM_DMACNTX_EN; > + reg |= FIELD_PREP(SHIM_DMACNTX_FMT, fmt->csi_df); > + > + /* > + * Using the values from the documentation gives incorrect ordering for > + * the luma and chroma components. In practice, the "reverse" format > + * gives the correct image. So for example, if the image is in UYVY, the > + * reverse would be YVYU. > + */ > + switch (fmt->fourcc) { > + case V4L2_PIX_FMT_UYVY: > + reg |= FIELD_PREP(SHIM_DMACNTX_YUV422, > + SHIM_DMACNTX_YVYU); > + break; > + case V4L2_PIX_FMT_VYUY: > + reg |= FIELD_PREP(SHIM_DMACNTX_YUV422, > + SHIM_DMACNTX_YUYV); > + break; > + case V4L2_PIX_FMT_YUYV: > + reg |= FIELD_PREP(SHIM_DMACNTX_YUV422, > + SHIM_DMACNTX_VYUY); > + break; > + case V4L2_PIX_FMT_YVYU: > + reg |= FIELD_PREP(SHIM_DMACNTX_YUV422, > + SHIM_DMACNTX_UYVY); > + break; > + default: > + /* Ignore if not YUV 4:2:2 */ > + break; > + } > + > + writel(reg, csi->shim + SHIM_DMACNTX); > + > + reg = FIELD_PREP(SHIM_PSI_CFG0_SRC_TAG, 0) | > + FIELD_PREP(SHIM_PSI_CFG0_DST_TAG, 1); > + writel(reg, csi->shim + SHIM_PSI_CFG0); > +} > + > +static void ti_csi2rx_dma_callback(void *param) > +{ > + struct ti_csi2rx_buffer *buf = param; > + struct ti_csi2rx_dev *csi = buf->csi; > + struct ti_csi2rx_dma *dma = &csi->dma; > + unsigned long flags = 0; > + > + buf->vb.vb2_buf.timestamp = ktime_get_ns(); > + buf->vb.sequence = csi->sequence++; > + > + spin_lock_irqsave(&dma->lock, flags); > + > + WARN_ON(dma->curr != buf); > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_DONE); > + > + /* If there are more buffers to process then start their transfer. */ > + dma->curr = NULL; > + while (!list_empty(&dma->queue)) { > + buf = list_entry(dma->queue.next, struct ti_csi2rx_buffer, list); > + list_del(&buf->list); > + > + if (ti_csi2rx_start_dma(csi, buf)) { > + dev_err(csi->dev, "Failed to queue the next buffer for DMA\n"); > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR); > + } else { > + dma->curr = buf; > + break; > + } > + } > + > + if (!dma->curr) > + dma->state = TI_CSI2RX_DMA_IDLE; > + > + spin_unlock_irqrestore(&dma->lock, flags); > +} > + > +static int ti_csi2rx_start_dma(struct ti_csi2rx_dev *csi, > + struct ti_csi2rx_buffer *buf) > +{ > + unsigned long addr; > + struct dma_async_tx_descriptor *desc; > + size_t len = csi->v_fmt.fmt.pix.sizeimage; > + dma_cookie_t cookie; > + int ret = 0; > + > + addr = vb2_dma_contig_plane_dma_addr(&buf->vb.vb2_buf, 0); > + desc = dmaengine_prep_slave_single(csi->dma.chan, addr, len, > + DMA_DEV_TO_MEM, > + DMA_PREP_INTERRUPT | DMA_CTRL_ACK); > + if (!desc) > + return -EIO; > + > + desc->callback = ti_csi2rx_dma_callback; > + desc->callback_param = buf; > + > + cookie = dmaengine_submit(desc); > + ret = dma_submit_error(cookie); > + if (ret) > + return ret; > + > + dma_async_issue_pending(csi->dma.chan); > + > + return 0; > +} > + > +static int ti_csi2rx_queue_setup(struct vb2_queue *q, unsigned int *nbuffers, > + unsigned int *nplanes, unsigned int sizes[], > + struct device *alloc_devs[]) > +{ > + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(q); > + unsigned int size = csi->v_fmt.fmt.pix.sizeimage; > + > + if (*nplanes) { > + if (sizes[0] < size) > + return -EINVAL; > + size = sizes[0]; > + } > + > + *nplanes = 1; > + sizes[0] = size; > + > + return 0; > +} > + > +static int ti_csi2rx_buffer_prepare(struct vb2_buffer *vb) > +{ > + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(vb->vb2_queue); > + unsigned long size = csi->v_fmt.fmt.pix.sizeimage; > + > + if (vb2_plane_size(vb, 0) < size) { > + dev_err(csi->dev, "Data will not fit into plane\n"); > + return -EINVAL; > + } > + > + vb2_set_plane_payload(vb, 0, size); > + return 0; > +} > + > +static void ti_csi2rx_buffer_queue(struct vb2_buffer *vb) > +{ > + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(vb->vb2_queue); > + struct ti_csi2rx_buffer *buf; > + struct ti_csi2rx_dma *dma = &csi->dma; > + unsigned long flags = 0; > + int ret; > + > + buf = container_of(vb, struct ti_csi2rx_buffer, vb.vb2_buf); > + buf->csi = csi; > + > + spin_lock_irqsave(&dma->lock, flags); > + /* > + * Usually the DMA callback takes care of queueing the pending buffers. > + * But if DMA has stalled due to lack of buffers, restart it now. > + */ > + if (dma->state == TI_CSI2RX_DMA_IDLE) { > + ret = ti_csi2rx_start_dma(csi, buf); > + if (ret) { > + dev_err(csi->dev, "Failed to start DMA: %d\n", ret); > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED); > + goto unlock; > + } > + > + dma->curr = buf; > + dma->state = TI_CSI2RX_DMA_ACTIVE; > + } else { > + list_add_tail(&buf->list, &dma->queue); > + } > + > +unlock: > + spin_unlock_irqrestore(&dma->lock, flags); > +} > + > +static int ti_csi2rx_start_streaming(struct vb2_queue *vq, unsigned int count) > +{ > + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(vq); > + struct ti_csi2rx_dma *dma = &csi->dma; > + struct ti_csi2rx_buffer *buf, *tmp; > + unsigned long flags; > + int ret = 0; > + > + spin_lock_irqsave(&dma->lock, flags); > + if (list_empty(&dma->queue)) > + ret = -EIO; > + spin_unlock_irqrestore(&dma->lock, flags); > + if (ret) > + return ret; > + > + ret = media_pipeline_start(&csi->vdev.entity, &csi->pipe); > + if (ret) > + goto err; > + > + ti_csi2rx_setup_shim(csi); > + > + ret = v4l2_subdev_call(csi->subdev, video, s_stream, 1); > + if (ret) > + goto err_pipeline; > + > + csi->sequence = 0; > + > + spin_lock_irqsave(&dma->lock, flags); > + buf = list_entry(dma->queue.next, struct ti_csi2rx_buffer, list); > + list_del(&buf->list); > + dma->state = TI_CSI2RX_DMA_ACTIVE; > + > + ret = ti_csi2rx_start_dma(csi, buf); > + if (ret) { > + dev_err(csi->dev, "Failed to start DMA: %d\n", ret); > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED); > + spin_unlock_irqrestore(&dma->lock, flags); > + goto err_stream; > + } > + > + dma->curr = buf; > + spin_unlock_irqrestore(&dma->lock, flags); > + > + return 0; > + > +err_stream: > + v4l2_subdev_call(csi->subdev, video, s_stream, 0); > +err_pipeline: > + media_pipeline_stop(&csi->vdev.entity); > +err: > + spin_lock_irqsave(&dma->lock, flags); > + list_for_each_entry_safe(buf, tmp, &dma->queue, list) { > + list_del(&buf->list); > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED); > + } > + csi->dma.state = TI_CSI2RX_DMA_STOPPED; > + spin_unlock_irqrestore(&dma->lock, flags); > + > + return ret; > +} > + > +static void ti_csi2rx_stop_streaming(struct vb2_queue *vq) > +{ > + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(vq); > + struct ti_csi2rx_buffer *buf = NULL, *tmp; > + struct ti_csi2rx_dma *dma = &csi->dma; > + unsigned long flags = 0; > + int ret; > + > + media_pipeline_stop(&csi->vdev.entity); > + > + ret = v4l2_subdev_call(csi->subdev, video, s_stream, 0); > + if (ret) > + dev_err(csi->dev, "Failed to stop subdev stream\n"); > + > + writel(0, csi->shim + SHIM_CNTL); > + > + ret = dmaengine_terminate_sync(csi->dma.chan); > + if (ret) > + dev_err(csi->dev, "Failed to stop DMA\n"); > + > + writel(0, csi->shim + SHIM_DMACNTX); > + > + spin_lock_irqsave(&dma->lock, flags); > + list_for_each_entry_safe(buf, tmp, &csi->dma.queue, list) { > + list_del(&buf->list); > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR); > + } > + > + if (dma->curr) > + vb2_buffer_done(&dma->curr->vb.vb2_buf, VB2_BUF_STATE_ERROR); > + > + dma->curr = NULL; > + dma->state = TI_CSI2RX_DMA_STOPPED; > + spin_unlock_irqrestore(&dma->lock, flags); > +} > + > +static const struct vb2_ops csi_vb2_qops = { > + .queue_setup = ti_csi2rx_queue_setup, > + .buf_prepare = ti_csi2rx_buffer_prepare, > + .buf_queue = ti_csi2rx_buffer_queue, > + .start_streaming = ti_csi2rx_start_streaming, > + .stop_streaming = ti_csi2rx_stop_streaming, > + .wait_prepare = vb2_ops_wait_prepare, > + .wait_finish = vb2_ops_wait_finish, > +}; > + > +static int ti_csi2rx_init_vb2q(struct ti_csi2rx_dev *csi) > +{ > + struct vb2_queue *q = &csi->vidq; > + int ret; > + > + q->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; > + q->io_modes = VB2_MMAP | VB2_USERPTR | VB2_DMABUF | VB2_READ; > + q->drv_priv = csi; > + q->buf_struct_size = sizeof(struct ti_csi2rx_buffer); > + q->ops = &csi_vb2_qops; > + q->mem_ops = &vb2_dma_contig_memops; > + q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC; > + q->dev = dmaengine_get_dma_device(csi->dma.chan); > + q->lock = &csi->mutex; > + > + ret = vb2_queue_init(q); > + if (ret) > + return ret; > + > + csi->vdev.queue = q; > + > + return 0; > +} > + > +static int ti_csi2rx_init_dma(struct ti_csi2rx_dev *csi) > +{ > + struct dma_slave_config cfg; > + int ret; > + > + INIT_LIST_HEAD(&csi->dma.queue); > + spin_lock_init(&csi->dma.lock); > + > + csi->dma.state = TI_CSI2RX_DMA_STOPPED; > + > + csi->dma.chan = dma_request_chan(csi->dev, "rx0"); > + if (IS_ERR(csi->dma.chan)) > + return PTR_ERR(csi->dma.chan); > + > + memset(&cfg, 0, sizeof(cfg)); > + > + cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_16_BYTES; You could do this when you declare cfg, and omit the memset. > + > + ret = dmaengine_slave_config(csi->dma.chan, &cfg); > + if (ret) dma_release_chan() ? > + return ret; > + > + return 0; > +} > + > +static int ti_csi2rx_v4l2_init(struct ti_csi2rx_dev *csi) > +{ > + struct media_device *mdev = &csi->mdev; > + struct video_device *vdev = &csi->vdev; > + const struct ti_csi2rx_fmt *fmt; > + struct v4l2_pix_format *pix_fmt = &csi->v_fmt.fmt.pix; > + int ret; > + > + fmt = find_format_by_pix(V4L2_PIX_FMT_UYVY); > + if (!fmt) > + return -EINVAL; > + > + pix_fmt->width = 640; > + pix_fmt->height = 480; > + > + ti_csi2rx_fill_fmt(fmt, &csi->v_fmt); > + > + mdev->dev = csi->dev; > + mdev->hw_revision = 1; > + strscpy(mdev->model, "TI-CSI2RX", sizeof(mdev->model)); > + snprintf(mdev->bus_info, sizeof(mdev->bus_info), "platform:%s", > + dev_name(mdev->dev)); > + > + media_device_init(mdev); > + > + strscpy(vdev->name, TI_CSI2RX_MODULE_NAME, sizeof(vdev->name)); > + vdev->v4l2_dev = &csi->v4l2_dev; > + vdev->vfl_dir = VFL_DIR_RX; > + vdev->fops = &csi_fops; > + vdev->ioctl_ops = &csi_ioctl_ops; > + vdev->release = video_device_release_empty; > + vdev->device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_READWRITE | > + V4L2_CAP_STREAMING | V4L2_CAP_IO_MC; > + vdev->lock = &csi->mutex; > + video_set_drvdata(vdev, csi); > + > + csi->pad.flags = MEDIA_PAD_FL_SINK; You'll need to provide entity ops for the vdev entity with at least link_validate assigned. See e.g. drivers/media/pci/intel/ipu3/ipu3-cio2-main.cdrivers/media/pci/intel/ipu3/ipu3-cio2-main.c . > + ret = media_entity_pads_init(&csi->vdev.entity, 1, &csi->pad); > + if (ret) > + return ret; > + > + csi->v4l2_dev.mdev = mdev; > + > + ret = v4l2_device_register(csi->dev, &csi->v4l2_dev); > + if (ret) > + return ret; > + > + ret = media_device_register(mdev); > + if (ret) { > + v4l2_device_unregister(&csi->v4l2_dev); > + media_device_cleanup(mdev); > + return ret; > + } > + > + return 0; > +} > + > +static void ti_csi2rx_cleanup_dma(struct ti_csi2rx_dev *csi) > +{ > + dma_release_channel(csi->dma.chan); > +} > + > +static void ti_csi2rx_cleanup_v4l2(struct ti_csi2rx_dev *csi) > +{ > + media_device_unregister(&csi->mdev); > + v4l2_device_unregister(&csi->v4l2_dev); > + media_device_cleanup(&csi->mdev); > +} > + > +static void ti_csi2rx_cleanup_subdev(struct ti_csi2rx_dev *csi) > +{ > + v4l2_async_nf_unregister(&csi->notifier); > + v4l2_async_nf_cleanup(&csi->notifier); > +} > + > +static void ti_csi2rx_cleanup_vb2q(struct ti_csi2rx_dev *csi) > +{ > + vb2_queue_release(&csi->vidq); > +} > + > +static int ti_csi2rx_probe(struct platform_device *pdev) > +{ > + struct ti_csi2rx_dev *csi; > + struct resource *res; > + int ret; > + > + csi = devm_kzalloc(&pdev->dev, sizeof(*csi), GFP_KERNEL); > + if (!csi) > + return -ENOMEM; > + > + csi->dev = &pdev->dev; > + platform_set_drvdata(pdev, csi); > + > + mutex_init(&csi->mutex); > + > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > + csi->shim = devm_ioremap_resource(&pdev->dev, res); > + if (IS_ERR(csi->shim)) Remember mutex_destroy(). I'd add one more label below. > + return PTR_ERR(csi->shim); > + > + ret = ti_csi2rx_init_dma(csi); > + if (ret) > + return ret; > + > + ret = ti_csi2rx_v4l2_init(csi); > + if (ret) > + goto err_dma; > + > + ret = ti_csi2rx_init_vb2q(csi); > + if (ret) > + goto err_v4l2; > + > + ret = ti_csi2rx_init_subdev(csi); > + if (ret) > + goto err_vb2q; > + > + ret = of_platform_populate(csi->dev->of_node, NULL, NULL, csi->dev); > + if (ret) { > + dev_err(csi->dev, "Failed to create children: %d\n", ret); > + goto err_subdev; > + } > + > + return 0; > + > +err_subdev: > + ti_csi2rx_cleanup_subdev(csi); > +err_vb2q: > + ti_csi2rx_cleanup_vb2q(csi); > +err_v4l2: > + ti_csi2rx_cleanup_v4l2(csi); > +err_dma: > + ti_csi2rx_cleanup_dma(csi); > + return ret; > +} > + > +static int ti_csi2rx_remove(struct platform_device *pdev) > +{ > + struct ti_csi2rx_dev *csi = platform_get_drvdata(pdev); > + > + if (vb2_is_busy(&csi->vidq)) > + return -EBUSY; Hmm. I don't think this is useful. Unbinding MC-enabled devices is broken at the moment, so I think you can safely ignore this bit in drivers. > + > + video_unregister_device(&csi->vdev); > + > + ti_csi2rx_cleanup_vb2q(csi); > + ti_csi2rx_cleanup_subdev(csi); > + ti_csi2rx_cleanup_v4l2(csi); > + ti_csi2rx_cleanup_dma(csi); mutex_destroy() here, too. > + > + return 0; > +} > + > +static const struct of_device_id ti_csi2rx_of_match[] = { > + { .compatible = "ti,j721e-csi2rx", }, > + { }, > +}; > +MODULE_DEVICE_TABLE(of, ti_csi2rx_of_match); > + > +static struct platform_driver ti_csi2rx_pdrv = { > + .probe = ti_csi2rx_probe, > + .remove = ti_csi2rx_remove, > + .driver = { > + .name = TI_CSI2RX_MODULE_NAME, > + .of_match_table = ti_csi2rx_of_match, > + }, > +}; > + > +module_platform_driver(ti_csi2rx_pdrv); > + > +MODULE_DESCRIPTION("TI J721E CSI2 RX Driver"); > +MODULE_AUTHOR("Pratyush Yadav <p.yadav@ti.com>"); > +MODULE_LICENSE("GPL v2"); > +MODULE_VERSION("1.0");
Hi Laurent, Thanks for your review and sorry for the late reply. On 23/01/22 08:25PM, Laurent Pinchart wrote: > Hi Pratyush, > > Thank you for the patch. > > On Fri, Jan 21, 2022 at 07:59:01PM +0530, Pratyush Yadav wrote: > > TI's J721E uses the Cadence CSI2RX and DPHY peripherals to facilitate > > capture over a CSI-2 bus. > > > > The Cadence CSI2RX IP acts as a bridge between the TI specific parts and > > the CSI-2 protocol parts. TI then has a wrapper on top of this bridge > > called the SHIM layer. It takes in data from stream 0, repacks it, and > > sends it to memory over PSI-L DMA. > > > > This driver acts as the "front end" to V4L2 client applications. It > > implements the required ioctls and buffer operations, passes the > > necessary calls on to the bridge, programs the SHIM layer, and performs > > DMA via the dmaengine API to finally return the data to a buffer > > supplied by the application. > > > > Signed-off-by: Pratyush Yadav <p.yadav@ti.com> > > > > --- > > > > (no changes since v5) > > > > Changes in v5: > > - Add dependency on PHY_CADENCE_DPHY_RX instead of PHY_CADENCE_DPHY > > since the Rx mode DPHY now has a separate driver. > > - Drop ti_csi2rx_validate_pipeline(). Pipeline validation should be done > > at media_pipeline_start(). > > - Do not assign flags. > > - Fix error handling in ti_csi2rx_start_streaming(). Free up vb2 buffers > > when media_pipeline_start() fails. > > > > Changes in v4: > > - Acquire the media device's graph_mutex before starting the graph walk. > > - Call media_graph_walk_init() and media_graph_walk_cleanup() when > > starting and ending the graph walk respectively. > > - Reduce max frame height and width in enum_framesizes. Currently they > > are set to UINT_MAX but they must be a multiple of step_width, so they > > need to be rounded down. Also, these values are absurdly large which > > causes some userspace applications like gstreamer to trip up. While it > > is not generally right to change the kernel for an application bug, it > > is not such a big deal here. This change is replacing one set of > > absurdly large arbitrary values with another set of smaller but still > > absurdly large arbitrary values. Both limits are unlikely to be hit in > > practice. > > > > Changes in v3: > > - Move DMA related fields in struct ti_csi2rx_dma. > > - Protect DMA buffer queue with a spinlock to make sure the queue buffer > > and DMA callback don't race on it. > > - Track the current DMA state. It might go idle because of a lack of > > buffers. This state can be used to restart it if needed. > > - Do not include the current buffer in the pending queue. It is slightly > > better modelling than leaving it at the head of the pending queue. > > - Use the buffer as the callback argument, and add a reference to csi in it. > > - If queueing a buffer to DMA fails, the buffer gets leaked and DMA gets > > stalled with. Instead, report the error to vb2 and queue the next > > buffer in the pending queue. > > - DMA gets stalled if we run out of buffers since the callback is the > > only one that fires subsequent transfers and it is no longer being > > called. Check for that when queueing buffers and restart DMA if > > needed. > > - Do not put of node until we are done using the fwnode. > > - Set inital format to UYVY 640x480. > > > > Changes in v2: > > - Use dmaengine_get_dma_device() instead of directly accessing > > dma->device->dev. > > - Do not set dst_addr_width when configuring slave DMA. > > - Move to a separate subdir and rename to j721e-csi2rx.c > > - Convert compatible to ti,j721e-csi2rx. > > - Move to use Media Controller centric APIs. > > - Improve cleanup in probe when one of the steps fails. > > - Add colorspace to formats database. > > - Set hw_revision on media_device. > > - Move video device initialization to probe time instead of register time. > > > > MAINTAINERS | 6 + > > drivers/media/platform/Kconfig | 12 + > > drivers/media/platform/ti/Makefile | 1 + > > .../media/platform/ti/j721e-csi2rx/Makefile | 2 + > > .../platform/ti/j721e-csi2rx/j721e-csi2rx.c | 913 ++++++++++++++++++ > > 5 files changed, 934 insertions(+) > > create mode 100644 drivers/media/platform/ti/j721e-csi2rx/Makefile > > create mode 100644 drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c > > > > diff --git a/MAINTAINERS b/MAINTAINERS > > index 3b8fa4e5047f..2a8ebf17462e 100644 > > --- a/MAINTAINERS > > +++ b/MAINTAINERS > > @@ -19181,6 +19181,12 @@ S: Odd Fixes > > F: drivers/clk/ti/ > > F: include/linux/clk/ti.h > > > > +TI J721E CSI2RX DRIVER > > +M: Pratyush Yadav <p.yadav@ti.com> > > +L: linux-media@vger.kernel.org > > +S: Supported > > +F: drivers/media/platform/ti/j721e-csi2rx/ > > + > > TI DAVINCI MACHINE SUPPORT > > M: Sekhar Nori <nsekhar@ti.com> > > R: Bartosz Golaszewski <brgl@bgdev.pl> > > diff --git a/drivers/media/platform/Kconfig b/drivers/media/platform/Kconfig > > index 9fbdba0fd1e7..0fa58563d93b 100644 > > --- a/drivers/media/platform/Kconfig > > +++ b/drivers/media/platform/Kconfig > > @@ -216,6 +216,18 @@ config VIDEO_RCAR_ISP > > To compile this driver as a module, choose M here: the > > module will be called rcar-isp. > > > > +config VIDEO_TI_J721E_CSI2RX > > + tristate "TI J721E CSI2RX wrapper layer driver" > > + depends on VIDEO_DEV && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API > > + depends on MEDIA_SUPPORT && MEDIA_CONTROLLER > > + depends on PHY_CADENCE_DPHY_RX && VIDEO_CADENCE_CSI2RX > > + depends on ARCH_K3 || COMPILE_TEST > > + select VIDEOBUF2_DMA_CONTIG > > + select V4L2_FWNODE > > + help > > + Support for TI CSI2RX wrapper layer. This just enables the wrapper driver. > > + The Cadence CSI2RX bridge driver needs to be enabled separately. > > + > > endif # V4L_PLATFORM_DRIVERS > > > > menuconfig V4L_MEM2MEM_DRIVERS > > diff --git a/drivers/media/platform/ti/Makefile b/drivers/media/platform/ti/Makefile > > index bbc737ccbbea..17c9cfb74f66 100644 > > --- a/drivers/media/platform/ti/Makefile > > +++ b/drivers/media/platform/ti/Makefile > > @@ -1,3 +1,4 @@ > > # SPDX-License-Identifier: GPL-2.0 > > obj-y += cal/ > > obj-y += vpe/ > > +obj-y += j721e-csi2rx/ > > Alphabetical order maybe ? > > > diff --git a/drivers/media/platform/ti/j721e-csi2rx/Makefile b/drivers/media/platform/ti/j721e-csi2rx/Makefile > > new file mode 100644 > > index 000000000000..377afc1d6280 > > --- /dev/null > > +++ b/drivers/media/platform/ti/j721e-csi2rx/Makefile > > @@ -0,0 +1,2 @@ > > +# SPDX-License-Identifier: GPL-2.0 > > +obj-$(CONFIG_VIDEO_TI_J721E_CSI2RX) += j721e-csi2rx.o > > diff --git a/drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c b/drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c > > new file mode 100644 > > index 000000000000..43f31f161f43 > > --- /dev/null > > +++ b/drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c > > @@ -0,0 +1,913 @@ > > +// SPDX-License-Identifier: GPL-2.0-only > > +/* > > + * TI CSI2 RX driver. > > + * > > + * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/ > > + * > > + * Author: Pratyush Yadav <p.yadav@ti.com> > > + */ > > + > > +#include <linux/bitfield.h> > > +#include <linux/module.h> > > +#include <linux/platform_device.h> > > +#include <linux/dmaengine.h> > > +#include <linux/of_platform.h> > > Alphabetical order would be nice here too. > > > + > > +#include <media/v4l2-device.h> > > +#include <media/v4l2-ioctl.h> > > +#include <media/videobuf2-dma-contig.h> > > + > > +#define TI_CSI2RX_MODULE_NAME "j721e-csi2rx" > > + > > +#define SHIM_CNTL 0x10 > > +#define SHIM_CNTL_PIX_RST BIT(0) > > + > > +#define SHIM_DMACNTX 0x20 > > +#define SHIM_DMACNTX_EN BIT(31) > > +#define SHIM_DMACNTX_YUV422 GENMASK(27, 26) > > +#define SHIM_DMACNTX_FMT GENMASK(5, 0) > > +#define SHIM_DMACNTX_UYVY 0 > > +#define SHIM_DMACNTX_VYUY 1 > > +#define SHIM_DMACNTX_YUYV 2 > > +#define SHIM_DMACNTX_YVYU 3 > > + > > +#define SHIM_PSI_CFG0 0x24 > > +#define SHIM_PSI_CFG0_SRC_TAG GENMASK(15, 0) > > +#define SHIM_PSI_CFG0_DST_TAG GENMASK(31, 15) > > + > > +#define CSI_DF_YUV420 0x18 > > +#define CSI_DF_YUV422 0x1e > > +#define CSI_DF_RGB444 0x20 > > +#define CSI_DF_RGB888 0x24 > > https://lore.kernel.org/linux-media/20220123160857.24161-2-laurent.pinchart+renesas@ideasonboard.com/ > > :-) > > > + > > +#define PSIL_WORD_SIZE_BYTES 16 > > +/* > > + * There are no hard limits on the width or height. The DMA engine can handle > > + * all sizes. The max width and height are arbitrary numbers for this driver. > > + * Use 16M * 16M as the arbitrary limit. It is large enough that it is unlikely > > + * the limit will be hit in practice. > > + */ > > +#define MAX_WIDTH_BYTES SZ_16M > > +#define MAX_HEIGHT_BYTES SZ_16M > > + > > +struct ti_csi2rx_fmt { > > + u32 fourcc; /* Four character code. */ > > + u32 code; /* Mbus code. */ > > + enum v4l2_colorspace colorspace; > > + u32 csi_df; /* CSI Data format. */ > > It's called data type in CSI-2, not data format. > > > + u8 bpp; /* Bits per pixel. */ > > +}; > > + > > +struct ti_csi2rx_buffer { > > + /* Common v4l2 buffer. Must be first. */ > > + struct vb2_v4l2_buffer vb; > > + struct list_head list; > > + struct ti_csi2rx_dev *csi; > > +}; > > + > > +enum ti_csi2rx_dma_state { > > + TI_CSI2RX_DMA_STOPPED, /* Streaming not started yet. */ > > + TI_CSI2RX_DMA_IDLE, /* Streaming but no pending DMA operation. */ > > + TI_CSI2RX_DMA_ACTIVE, /* Streaming and pending DMA operation. */ > > +}; > > + > > +struct ti_csi2rx_dma { > > + /* Protects all fields in this struct. */ > > + spinlock_t lock; > > + struct dma_chan *chan; > > + /* Buffers queued to the driver, waiting to be processed by DMA. */ > > + struct list_head queue; > > + enum ti_csi2rx_dma_state state; > > + /* > > + * Current buffer being processed by DMA. NULL if no buffer is being > > + * processed. > > + */ > > + struct ti_csi2rx_buffer *curr; > > +}; > > + > > +struct ti_csi2rx_dev { > > + struct device *dev; > > + void __iomem *shim; > > + struct v4l2_device v4l2_dev; > > + struct video_device vdev; > > + struct media_device mdev; > > + struct media_pipeline pipe; > > + struct media_pad pad; > > + struct v4l2_async_notifier notifier; > > + struct v4l2_subdev *subdev; > > + struct vb2_queue vidq; > > + struct mutex mutex; /* To serialize ioctls. */ > > + struct v4l2_format v_fmt; > > + struct ti_csi2rx_dma dma; > > + u32 sequence; > > +}; > > + > > +static const struct ti_csi2rx_fmt formats[] = { > > + { > > + .fourcc = V4L2_PIX_FMT_YUYV, > > + .code = MEDIA_BUS_FMT_YUYV8_2X8, > > + .colorspace = V4L2_COLORSPACE_SRGB, > > + .csi_df = CSI_DF_YUV422, > > + .bpp = 16, > > + }, { > > + .fourcc = V4L2_PIX_FMT_UYVY, > > + .code = MEDIA_BUS_FMT_UYVY8_2X8, > > + .colorspace = V4L2_COLORSPACE_SRGB, > > + .csi_df = CSI_DF_YUV422, > > + .bpp = 16, > > + }, { > > + .fourcc = V4L2_PIX_FMT_YVYU, > > + .code = MEDIA_BUS_FMT_YVYU8_2X8, > > + .colorspace = V4L2_COLORSPACE_SRGB, > > + .csi_df = CSI_DF_YUV422, > > + .bpp = 16, > > + }, { > > + .fourcc = V4L2_PIX_FMT_VYUY, > > + .code = MEDIA_BUS_FMT_VYUY8_2X8, > > + .colorspace = V4L2_COLORSPACE_SRGB, > > + .csi_df = CSI_DF_YUV422, > > + .bpp = 16, > > + }, > > + > > + /* More formats can be supported but they are not listed for now. */ > > +}; > > + > > +static const unsigned int num_formats = ARRAY_SIZE(formats); > > + > > +/* Forward declaration needed by ti_csi2rx_dma_callback. */ > > +static int ti_csi2rx_start_dma(struct ti_csi2rx_dev *csi, > > + struct ti_csi2rx_buffer *buf); > > + > > +static const struct ti_csi2rx_fmt *find_format_by_pix(u32 pixelformat) > > +{ > > + unsigned int i; > > + > > + for (i = 0; i < num_formats; i++) { > > + if (formats[i].fourcc == pixelformat) > > + return &formats[i]; > > + } > > + > > + return NULL; > > +} > > + > > +static void ti_csi2rx_fill_fmt(const struct ti_csi2rx_fmt *csi_fmt, > > + struct v4l2_format *v4l2_fmt) > > +{ > > + struct v4l2_pix_format *pix = &v4l2_fmt->fmt.pix; > > + u32 bpl; > > + > > + v4l2_fmt->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; > > + pix->pixelformat = csi_fmt->fourcc; > > + pix->colorspace = csi_fmt->colorspace; > > I'd drop this (and the colorspace field in ti_csi2rx_fmt). This driver > doesn't care about colorspaces, it should accept any value set by > userspace, which should match the colorspace produced by the source > subdev. > > ti_csi2rx_v4l2_init() will have to set a default colorspace explicitly. > > > + pix->sizeimage = pix->height * pix->width * (csi_fmt->bpp / 8); > > + > > + bpl = (pix->width * ALIGN(csi_fmt->bpp, 8)) >> 3; > > + pix->bytesperline = ALIGN(bpl, 16); > > +} > > + > > +static int ti_csi2rx_querycap(struct file *file, void *priv, > > + struct v4l2_capability *cap) > > +{ > > + struct ti_csi2rx_dev *csi = video_drvdata(file); > > + > > + strscpy(cap->driver, TI_CSI2RX_MODULE_NAME, sizeof(cap->driver)); > > + strscpy(cap->card, TI_CSI2RX_MODULE_NAME, sizeof(cap->card)); > > + > > + snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s", > > + dev_name(csi->dev)); > > Depending on which series gets merged, you can drop this line: > > https://lore.kernel.org/linux-media/20220122163656.168440-1-sakari.ailus@linux.intel.com/ I don't see it merged yet, so leaving this as-is. > > > + return 0; > > +} > > + > > +static int ti_csi2rx_enum_fmt_vid_cap(struct file *file, void *priv, > > + struct v4l2_fmtdesc *f) > > +{ > > + if (f->index >= num_formats) > > + return -EINVAL; > > + > > + memset(f->reserved, 0, sizeof(f->reserved)); > > + f->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; > > + f->pixelformat = formats[f->index].fourcc; > > + > > + return 0; > > +} > > + > > +static int ti_csi2rx_g_fmt_vid_cap(struct file *file, void *prov, > > + struct v4l2_format *f) > > +{ > > + struct ti_csi2rx_dev *csi = video_drvdata(file); > > + > > + *f = csi->v_fmt; > > + > > + return 0; > > +} > > + > > +static int ti_csi2rx_try_fmt_vid_cap(struct file *file, void *priv, > > + struct v4l2_format *f) > > +{ > > + const struct ti_csi2rx_fmt *fmt; > > + > > + /* > > + * Default to the first format if the requested pixel format code isn't > > + * supported. > > + */ > > + fmt = find_format_by_pix(f->fmt.pix.pixelformat); > > + if (!fmt) > > + fmt = &formats[0]; > > + > > + if (f->fmt.pix.field == V4L2_FIELD_ANY) > > + f->fmt.pix.field = V4L2_FIELD_NONE; > > + > > + if (f->fmt.pix.field != V4L2_FIELD_NONE) > > + return -EINVAL; > > You should adjust the field, not return an error, so this can just > become > > /* Interlaced formats are not supported. */ > f->fmt.pix.field = V4L2_FIELD_NONE; > > > + > > + ti_csi2rx_fill_fmt(fmt, f); > > + > > + return 0; > > +} > > + > > +static int ti_csi2rx_s_fmt_vid_cap(struct file *file, void *priv, > > + struct v4l2_format *f) > > +{ > > + struct ti_csi2rx_dev *csi = video_drvdata(file); > > + struct vb2_queue *q = &csi->vidq; > > + int ret; > > + > > + if (vb2_is_busy(q)) > > + return -EBUSY; > > + > > + ret = ti_csi2rx_try_fmt_vid_cap(file, priv, f); > > + if (ret < 0) > > + return ret; > > + > > + csi->v_fmt = *f; > > + > > + return 0; > > +} > > + > > +static int ti_csi2rx_enum_framesizes(struct file *file, void *fh, > > + struct v4l2_frmsizeenum *fsize) > > +{ > > + const struct ti_csi2rx_fmt *fmt; > > + unsigned int pixels_in_word; > > + u8 bpp; > > + > > + fmt = find_format_by_pix(fsize->pixel_format); > > + if (!fmt) > > + return -EINVAL; > > + > > + bpp = ALIGN(fmt->bpp, 8); > > + > > + /* > > + * Number of pixels in one PSI-L word. The transfer happens in multiples > > + * of PSI-L word sizes. > > + */ > > + pixels_in_word = PSIL_WORD_SIZE_BYTES * 8 / bpp; > > + > > + fsize->type = V4L2_FRMSIZE_TYPE_STEPWISE; > > + fsize->stepwise.min_width = pixels_in_word; > > + fsize->stepwise.max_width = rounddown(MAX_WIDTH_BYTES, pixels_in_word); > > + fsize->stepwise.step_width = pixels_in_word; > > + fsize->stepwise.min_height = 1; > > + fsize->stepwise.max_height = MAX_HEIGHT_BYTES; > > + fsize->stepwise.step_height = 1; > > + > > + return 0; > > +} > > + > > +static const struct v4l2_ioctl_ops csi_ioctl_ops = { > > + .vidioc_querycap = ti_csi2rx_querycap, > > + .vidioc_enum_fmt_vid_cap = ti_csi2rx_enum_fmt_vid_cap, > > + .vidioc_try_fmt_vid_cap = ti_csi2rx_try_fmt_vid_cap, > > + .vidioc_g_fmt_vid_cap = ti_csi2rx_g_fmt_vid_cap, > > + .vidioc_s_fmt_vid_cap = ti_csi2rx_s_fmt_vid_cap, > > + .vidioc_enum_framesizes = ti_csi2rx_enum_framesizes, > > + .vidioc_reqbufs = vb2_ioctl_reqbufs, > > + .vidioc_create_bufs = vb2_ioctl_create_bufs, > > + .vidioc_prepare_buf = vb2_ioctl_prepare_buf, > > + .vidioc_querybuf = vb2_ioctl_querybuf, > > + .vidioc_qbuf = vb2_ioctl_qbuf, > > + .vidioc_dqbuf = vb2_ioctl_dqbuf, > > + .vidioc_expbuf = vb2_ioctl_expbuf, > > + .vidioc_streamon = vb2_ioctl_streamon, > > + .vidioc_streamoff = vb2_ioctl_streamoff, > > +}; > > + > > +static const struct v4l2_file_operations csi_fops = { > > + .owner = THIS_MODULE, > > + .open = v4l2_fh_open, > > + .release = vb2_fop_release, > > + .read = vb2_fop_read, > > + .poll = vb2_fop_poll, > > + .unlocked_ioctl = video_ioctl2, > > + .mmap = vb2_fop_mmap, > > +}; > > + > > +static int ti_csi2rx_video_register(struct ti_csi2rx_dev *csi) > > +{ > > + struct video_device *vdev = &csi->vdev; > > + int ret, src_pad; > > + > > + ret = video_register_device(vdev, VFL_TYPE_VIDEO, -1); > > + if (ret) > > + return ret; > > + > > + src_pad = media_entity_get_fwnode_pad(&csi->subdev->entity, > > + csi->subdev->fwnode, > > + MEDIA_PAD_FL_SOURCE); > > + if (src_pad < 0) { > > + dev_err(csi->dev, "Couldn't find source pad for subdev\n"); > > + return src_pad; > > + } > > + > > + ret = media_create_pad_link(&csi->subdev->entity, src_pad, > > + &vdev->entity, 0, > > + MEDIA_LNK_FL_IMMUTABLE | > > + MEDIA_LNK_FL_ENABLED); > > + if (ret) { > > + video_unregister_device(vdev); > > + return ret; > > + } > > This can be simplified by using v4l2_create_fwnode_links_to_pad(). I don't think it can. v4l2_create_fwnode_links_to_pad() expects the sink pad to be backed by a v4l2 subdev. But in this case, the sink pad is backed by a video device instead. > > > + > > + return 0; > > +} > > + > > +static int csi_async_notifier_bound(struct v4l2_async_notifier *notifier, > > + struct v4l2_subdev *subdev, > > + struct v4l2_async_subdev *asd) > > +{ > > + struct ti_csi2rx_dev *csi = dev_get_drvdata(notifier->v4l2_dev->dev); > > + > > + csi->subdev = subdev; > > + > > + return 0; > > +} > > + > > +static int csi_async_notifier_complete(struct v4l2_async_notifier *notifier) > > +{ > > + struct ti_csi2rx_dev *csi = dev_get_drvdata(notifier->v4l2_dev->dev); > > + int ret; > > + > > + ret = ti_csi2rx_video_register(csi); > > I would inline the ti_csi2rx_video_register() function here, it's not > large, and it's only called in a single place. I'd guess the compiler would do it anyway but ok. > > > + if (ret) > > + return ret; > > + > > + return v4l2_device_register_subdev_nodes(&csi->v4l2_dev); > > +} > > + > > +static const struct v4l2_async_notifier_operations csi_async_notifier_ops = { > > + .bound = csi_async_notifier_bound, > > + .complete = csi_async_notifier_complete, > > +}; > > + > > +static int ti_csi2rx_init_subdev(struct ti_csi2rx_dev *csi) > > +{ > > + struct fwnode_handle *fwnode; > > + struct v4l2_async_subdev *asd; > > + struct device_node *node; > > + int ret; > > + > > + node = of_get_child_by_name(csi->dev->of_node, "csi-bridge"); > > + if (!node) > > + return -EINVAL; > > + > > + fwnode = of_fwnode_handle(node); > > + if (!fwnode) { > > + of_node_put(node); > > + return -EINVAL; > > + } > > + > > + v4l2_async_nf_init(&csi->notifier); > > + csi->notifier.ops = &csi_async_notifier_ops; > > + > > + asd = v4l2_async_nf_add_fwnode(&csi->notifier, fwnode, > > + struct v4l2_async_subdev); > > + of_node_put(node); > > + if (IS_ERR(asd)) { > > + v4l2_async_nf_cleanup(&csi->notifier); > > + return PTR_ERR(asd); > > + } > > + > > + ret = v4l2_async_nf_register(&csi->v4l2_dev, &csi->notifier); > > + if (ret) { > > + v4l2_async_nf_cleanup(&csi->notifier); > > + return ret; > > + } > > + > > + return 0; > > +} > > + > > +static void ti_csi2rx_setup_shim(struct ti_csi2rx_dev *csi) > > +{ > > + const struct ti_csi2rx_fmt *fmt; > > + unsigned int reg; > > + > > + fmt = find_format_by_pix(csi->v_fmt.fmt.pix.pixelformat); > > + if (!fmt) { > > + dev_err(csi->dev, "Unknown format\n"); > > + return; > > + } > > + > > + /* De-assert the pixel interface reset. */ > > + reg = SHIM_CNTL_PIX_RST; > > + writel(reg, csi->shim + SHIM_CNTL); > > + > > + reg = SHIM_DMACNTX_EN; > > + reg |= FIELD_PREP(SHIM_DMACNTX_FMT, fmt->csi_df); > > + > > + /* > > + * Using the values from the documentation gives incorrect ordering for > > + * the luma and chroma components. In practice, the "reverse" format > > + * gives the correct image. So for example, if the image is in UYVY, the > > + * reverse would be YVYU. > > Are you sure this is an issue in the documentation, not in the > implementation of the source subdev ? I have not probed the data lines or anything, but I see that on AM65x the same camera module and driver produce the output in the correct order. So I would guess that the source subdev is not the problem here. I do not have any other YUV cameras to double-check this with though. > > > + */ > > + switch (fmt->fourcc) { > > + case V4L2_PIX_FMT_UYVY: > > + reg |= FIELD_PREP(SHIM_DMACNTX_YUV422, > > + SHIM_DMACNTX_YVYU); > > + break; > > + case V4L2_PIX_FMT_VYUY: > > + reg |= FIELD_PREP(SHIM_DMACNTX_YUV422, > > + SHIM_DMACNTX_YUYV); > > + break; > > + case V4L2_PIX_FMT_YUYV: > > + reg |= FIELD_PREP(SHIM_DMACNTX_YUV422, > > + SHIM_DMACNTX_VYUY); > > + break; > > + case V4L2_PIX_FMT_YVYU: > > + reg |= FIELD_PREP(SHIM_DMACNTX_YUV422, > > + SHIM_DMACNTX_UYVY); > > + break; > > + default: > > + /* Ignore if not YUV 4:2:2 */ > > + break; > > + } > > + > > + writel(reg, csi->shim + SHIM_DMACNTX); > > + > > + reg = FIELD_PREP(SHIM_PSI_CFG0_SRC_TAG, 0) | > > + FIELD_PREP(SHIM_PSI_CFG0_DST_TAG, 1); > > + writel(reg, csi->shim + SHIM_PSI_CFG0); > > +} > > + > > +static void ti_csi2rx_dma_callback(void *param) > > +{ > > + struct ti_csi2rx_buffer *buf = param; > > + struct ti_csi2rx_dev *csi = buf->csi; > > + struct ti_csi2rx_dma *dma = &csi->dma; > > + unsigned long flags = 0; > > No need to initialize flags to 0. > > > + > > + buf->vb.vb2_buf.timestamp = ktime_get_ns(); > > + buf->vb.sequence = csi->sequence++; > > Is there any hardware frame counter that could be used, to detect > dropped frames ? Or maybe a SOF hardware interrupt somewhere (either in > the SHIM or the CSI-2 receiver) ? There is a register in the Cadence CSI2RX core (driven by drivers/media/platform/cadence/cdns-csi2rx.c) that tells the frame number. But I don't see any easy way to get that information into this driver. > > > + > > + spin_lock_irqsave(&dma->lock, flags); > > + > > + WARN_ON(dma->curr != buf); > > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_DONE); > > + > > + /* If there are more buffers to process then start their transfer. */ > > + dma->curr = NULL; > > + while (!list_empty(&dma->queue)) { > > + buf = list_entry(dma->queue.next, struct ti_csi2rx_buffer, list); > > + list_del(&buf->list); > > + > > + if (ti_csi2rx_start_dma(csi, buf)) { > > + dev_err(csi->dev, "Failed to queue the next buffer for DMA\n"); > > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR); > > If this buffer fails to be queued, do you expect that the next buffer in > the list would succeed ? It seems to be a fatal error to me. Not always. For example, ti_csi2rx_start_dma() calls dmaengine_prep_slave_single(). This would go to udma_prep_slave_sg(). This function makes some malloc() calls for example. Under memory pressure, those calls might fail. But on subsequent runs they might succeed if more memory is available. I admit this is very unlikely to happen in practice. I don't know the UDMA driver well enough to comment on whether or not it can fail due to some resource constraints under stress. But I don't think it is this driver's place to decide what DMA error is recoverable and which is not. > > > + } else { > > + dma->curr = buf; > > + break; > > Shouldn't all pending buffers be queued to the DMA engine ? It seems > that you're queuing one buffer at a time, which would cause an underrun > if the system is too slow to queue the next buffer during vertical > blanking. It defeats the point of having multiple buffers in the V4L2 > queue. You should instead queue the buffers to the DMA engine as soon as > they're received by the driver. Okay, I can do that in this driver. But one point to note here is that the UDMA driver does not currently support pushing multiple buffers for processing at the same time. It pushes one buffer and once it gets an interrupt for its completion, it pushes the next one. Queuing multiple buffers from CSI driver side would still be a bit faster since the next buffer would be pushed to the hardware ring in the interrupt handler, instead of having to wait for the callback to execute. But at the end of the day we would not end up pushing multiple buffers to the _hardware_. That of course is a limitation of the TI UDMA driver that needs to be fixed, but I can at least queue all the buffer from the CSI driver side. > > > + } > > + } > > + > > + if (!dma->curr) > > + dma->state = TI_CSI2RX_DMA_IDLE; > > + > > + spin_unlock_irqrestore(&dma->lock, flags); > > +} > > + > > +static int ti_csi2rx_start_dma(struct ti_csi2rx_dev *csi, > > + struct ti_csi2rx_buffer *buf) > > +{ > > + unsigned long addr; > > + struct dma_async_tx_descriptor *desc; > > + size_t len = csi->v_fmt.fmt.pix.sizeimage; > > + dma_cookie_t cookie; > > + int ret = 0; > > + > > + addr = vb2_dma_contig_plane_dma_addr(&buf->vb.vb2_buf, 0); > > + desc = dmaengine_prep_slave_single(csi->dma.chan, addr, len, > > + DMA_DEV_TO_MEM, > > + DMA_PREP_INTERRUPT | DMA_CTRL_ACK); > > + if (!desc) > > + return -EIO; > > + > > + desc->callback = ti_csi2rx_dma_callback; > > + desc->callback_param = buf; > > + > > + cookie = dmaengine_submit(desc); > > + ret = dma_submit_error(cookie); > > + if (ret) > > + return ret; > > + > > + dma_async_issue_pending(csi->dma.chan); > > + > > + return 0; > > +} > > + > > +static int ti_csi2rx_queue_setup(struct vb2_queue *q, unsigned int *nbuffers, > > + unsigned int *nplanes, unsigned int sizes[], > > + struct device *alloc_devs[]) > > +{ > > + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(q); > > + unsigned int size = csi->v_fmt.fmt.pix.sizeimage; > > + > > + if (*nplanes) { > > + if (sizes[0] < size) > > + return -EINVAL; > > + size = sizes[0]; > > + } > > + > > + *nplanes = 1; > > + sizes[0] = size; > > + > > + return 0; > > +} > > + > > +static int ti_csi2rx_buffer_prepare(struct vb2_buffer *vb) > > +{ > > + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(vb->vb2_queue); > > + unsigned long size = csi->v_fmt.fmt.pix.sizeimage; > > + > > + if (vb2_plane_size(vb, 0) < size) { > > + dev_err(csi->dev, "Data will not fit into plane\n"); > > + return -EINVAL; > > + } > > + > > + vb2_set_plane_payload(vb, 0, size); > > + return 0; > > +} > > + > > +static void ti_csi2rx_buffer_queue(struct vb2_buffer *vb) > > +{ > > + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(vb->vb2_queue); > > + struct ti_csi2rx_buffer *buf; > > + struct ti_csi2rx_dma *dma = &csi->dma; > > + unsigned long flags = 0; > > + int ret; > > + > > + buf = container_of(vb, struct ti_csi2rx_buffer, vb.vb2_buf); > > + buf->csi = csi; > > + > > + spin_lock_irqsave(&dma->lock, flags); > > + /* > > + * Usually the DMA callback takes care of queueing the pending buffers. > > + * But if DMA has stalled due to lack of buffers, restart it now. > > + */ > > + if (dma->state == TI_CSI2RX_DMA_IDLE) { > > + ret = ti_csi2rx_start_dma(csi, buf); > > + if (ret) { > > + dev_err(csi->dev, "Failed to start DMA: %d\n", ret); > > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED); > > + goto unlock; > > + } > > + > > + dma->curr = buf; > > + dma->state = TI_CSI2RX_DMA_ACTIVE; > > + } else { > > + list_add_tail(&buf->list, &dma->queue); > > + } > > + > > +unlock: > > + spin_unlock_irqrestore(&dma->lock, flags); > > +} > > + > > +static int ti_csi2rx_start_streaming(struct vb2_queue *vq, unsigned int count) > > +{ > > + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(vq); > > + struct ti_csi2rx_dma *dma = &csi->dma; > > + struct ti_csi2rx_buffer *buf, *tmp; > > + unsigned long flags; > > + int ret = 0; > > + > > + spin_lock_irqsave(&dma->lock, flags); > > + if (list_empty(&dma->queue)) > > + ret = -EIO; > > + spin_unlock_irqrestore(&dma->lock, flags); > > + if (ret) > > + return ret; > > + > > + ret = media_pipeline_start(&csi->vdev.entity, &csi->pipe); > > + if (ret) > > + goto err; > > + > > + ti_csi2rx_setup_shim(csi); > > + > > + ret = v4l2_subdev_call(csi->subdev, video, s_stream, 1); > > + if (ret) > > + goto err_pipeline; > > + > > + csi->sequence = 0; > > + > > + spin_lock_irqsave(&dma->lock, flags); > > + buf = list_entry(dma->queue.next, struct ti_csi2rx_buffer, list); > > + list_del(&buf->list); > > + dma->state = TI_CSI2RX_DMA_ACTIVE; > > + > > + ret = ti_csi2rx_start_dma(csi, buf); > > Shouldn't you start DMA before starting the source subdev ? You may miss > the first frame otherwise. Okay, I will do that. > > > + if (ret) { > > + dev_err(csi->dev, "Failed to start DMA: %d\n", ret); > > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED); > > + spin_unlock_irqrestore(&dma->lock, flags); > > + goto err_stream; > > + } > > + > > + dma->curr = buf; > > + spin_unlock_irqrestore(&dma->lock, flags); > > + > > + return 0; > > + > > +err_stream: > > + v4l2_subdev_call(csi->subdev, video, s_stream, 0); > > +err_pipeline: > > + media_pipeline_stop(&csi->vdev.entity); > > +err: > > + spin_lock_irqsave(&dma->lock, flags); > > + list_for_each_entry_safe(buf, tmp, &dma->queue, list) { > > + list_del(&buf->list); > > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED); > > + } > > + csi->dma.state = TI_CSI2RX_DMA_STOPPED; > > + spin_unlock_irqrestore(&dma->lock, flags); > > + > > + return ret; > > +} > > + > > +static void ti_csi2rx_stop_streaming(struct vb2_queue *vq) > > +{ > > + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(vq); > > + struct ti_csi2rx_buffer *buf = NULL, *tmp; > > + struct ti_csi2rx_dma *dma = &csi->dma; > > + unsigned long flags = 0; > > + int ret; > > + > > + media_pipeline_stop(&csi->vdev.entity); > > + > > + ret = v4l2_subdev_call(csi->subdev, video, s_stream, 0); > > + if (ret) > > + dev_err(csi->dev, "Failed to stop subdev stream\n"); > > + > > + writel(0, csi->shim + SHIM_CNTL); > > + > > + ret = dmaengine_terminate_sync(csi->dma.chan); > > + if (ret) > > + dev_err(csi->dev, "Failed to stop DMA\n"); > > + > > + writel(0, csi->shim + SHIM_DMACNTX); > > + > > Code from here... > > > + spin_lock_irqsave(&dma->lock, flags); > > + list_for_each_entry_safe(buf, tmp, &csi->dma.queue, list) { > > + list_del(&buf->list); > > + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR); > > + } > > + > > + if (dma->curr) > > + vb2_buffer_done(&dma->curr->vb.vb2_buf, VB2_BUF_STATE_ERROR); > > + > > + dma->curr = NULL; > > ... to here could be moved to a separate function that takes a VB2 buf > state parameter, to be also used in the error path of > ti_csi2rx_start_streaming(). Ok. > > > + dma->state = TI_CSI2RX_DMA_STOPPED; > > + spin_unlock_irqrestore(&dma->lock, flags); > > +} > > + > > +static const struct vb2_ops csi_vb2_qops = { > > + .queue_setup = ti_csi2rx_queue_setup, > > + .buf_prepare = ti_csi2rx_buffer_prepare, > > + .buf_queue = ti_csi2rx_buffer_queue, > > + .start_streaming = ti_csi2rx_start_streaming, > > + .stop_streaming = ti_csi2rx_stop_streaming, > > + .wait_prepare = vb2_ops_wait_prepare, > > + .wait_finish = vb2_ops_wait_finish, > > +}; > > + > > +static int ti_csi2rx_init_vb2q(struct ti_csi2rx_dev *csi) > > +{ > > + struct vb2_queue *q = &csi->vidq; > > + int ret; > > + > > + q->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; > > + q->io_modes = VB2_MMAP | VB2_USERPTR | VB2_DMABUF | VB2_READ; > > Usage of USERPTR and READ is not recommended, I'd drop them from the > driver. > > > + q->drv_priv = csi; > > + q->buf_struct_size = sizeof(struct ti_csi2rx_buffer); > > + q->ops = &csi_vb2_qops; > > + q->mem_ops = &vb2_dma_contig_memops; > > + q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC; > > + q->dev = dmaengine_get_dma_device(csi->dma.chan); > > That's interesting, why do you use the dmaengine device and not csi->dev > ? Because it is the dmaengine device that transfers the data from CSI. CSI has no built in DMA. > > > + q->lock = &csi->mutex; > > + > > + ret = vb2_queue_init(q); > > + if (ret) > > + return ret; > > + > > + csi->vdev.queue = q; > > + > > + return 0; > > +} > > + > > +static int ti_csi2rx_init_dma(struct ti_csi2rx_dev *csi) > > +{ > > + struct dma_slave_config cfg; > > struct dma_slave_config cfg = { }; > > and you can drop the memset below. Or possibly even better, > > struct dma_slave_config cfg = { > .src_addr_with = DMA_SLAVE_BUSWIDTH_16_BYTES, > }; > > > + int ret; > > + > > + INIT_LIST_HEAD(&csi->dma.queue); > > + spin_lock_init(&csi->dma.lock); > > + > > + csi->dma.state = TI_CSI2RX_DMA_STOPPED; > > + > > + csi->dma.chan = dma_request_chan(csi->dev, "rx0"); > > + if (IS_ERR(csi->dma.chan)) > > + return PTR_ERR(csi->dma.chan); > > + > > + memset(&cfg, 0, sizeof(cfg)); > > + > > + cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_16_BYTES; > > + > > + ret = dmaengine_slave_config(csi->dma.chan, &cfg); > > + if (ret) > > + return ret; > > + > > + return 0; > > +} > > + > > +static int ti_csi2rx_v4l2_init(struct ti_csi2rx_dev *csi) > > +{ > > + struct media_device *mdev = &csi->mdev; > > + struct video_device *vdev = &csi->vdev; > > + const struct ti_csi2rx_fmt *fmt; > > + struct v4l2_pix_format *pix_fmt = &csi->v_fmt.fmt.pix; > > + int ret; > > + > > + fmt = find_format_by_pix(V4L2_PIX_FMT_UYVY); > > + if (!fmt) > > + return -EINVAL; > > + > > + pix_fmt->width = 640; > > + pix_fmt->height = 480; > > Should you initialize ->field too ? > > > + > > + ti_csi2rx_fill_fmt(fmt, &csi->v_fmt); > > + > > + mdev->dev = csi->dev; > > + mdev->hw_revision = 1; > > + strscpy(mdev->model, "TI-CSI2RX", sizeof(mdev->model)); > > + snprintf(mdev->bus_info, sizeof(mdev->bus_info), "platform:%s", > > + dev_name(mdev->dev)); > > + > > + media_device_init(mdev); > > + > > + strscpy(vdev->name, TI_CSI2RX_MODULE_NAME, sizeof(vdev->name)); > > + vdev->v4l2_dev = &csi->v4l2_dev; > > + vdev->vfl_dir = VFL_DIR_RX; > > + vdev->fops = &csi_fops; > > + vdev->ioctl_ops = &csi_ioctl_ops; > > + vdev->release = video_device_release_empty; > > + vdev->device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_READWRITE | > > You can also drop V4L2_CAP_READWRITE if you drop VB2_READ above. > > > + V4L2_CAP_STREAMING | V4L2_CAP_IO_MC; > > + vdev->lock = &csi->mutex; > > + video_set_drvdata(vdev, csi); > > + > > + csi->pad.flags = MEDIA_PAD_FL_SINK; > > + ret = media_entity_pads_init(&csi->vdev.entity, 1, &csi->pad); > > + if (ret) > > + return ret; > > + > > + csi->v4l2_dev.mdev = mdev; > > + > > + ret = v4l2_device_register(csi->dev, &csi->v4l2_dev); > > + if (ret) > > + return ret; > > + > > + ret = media_device_register(mdev); > > + if (ret) { > > + v4l2_device_unregister(&csi->v4l2_dev); > > + media_device_cleanup(mdev); > > + return ret; > > + } > > + > > + return 0; > > +} > > + > > +static void ti_csi2rx_cleanup_dma(struct ti_csi2rx_dev *csi) > > +{ > > + dma_release_channel(csi->dma.chan); > > +} > > + > > +static void ti_csi2rx_cleanup_v4l2(struct ti_csi2rx_dev *csi) > > +{ > > + media_device_unregister(&csi->mdev); > > + v4l2_device_unregister(&csi->v4l2_dev); > > + media_device_cleanup(&csi->mdev); > > +} > > + > > +static void ti_csi2rx_cleanup_subdev(struct ti_csi2rx_dev *csi) > > +{ > > + v4l2_async_nf_unregister(&csi->notifier); > > + v4l2_async_nf_cleanup(&csi->notifier); > > +} > > + > > +static void ti_csi2rx_cleanup_vb2q(struct ti_csi2rx_dev *csi) > > +{ > > + vb2_queue_release(&csi->vidq); > > +} > > + > > +static int ti_csi2rx_probe(struct platform_device *pdev) > > +{ > > + struct ti_csi2rx_dev *csi; > > + struct resource *res; > > + int ret; > > + > > + csi = devm_kzalloc(&pdev->dev, sizeof(*csi), GFP_KERNEL); > > Don't use devm_kzalloc() here (see the explanation in the remove > function). > > > + if (!csi) > > + return -ENOMEM; > > + > > + csi->dev = &pdev->dev; > > + platform_set_drvdata(pdev, csi); > > + > > + mutex_init(&csi->mutex); > > + > > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > > + csi->shim = devm_ioremap_resource(&pdev->dev, res); > > + if (IS_ERR(csi->shim)) > > + return PTR_ERR(csi->shim); > > + > > + ret = ti_csi2rx_init_dma(csi); > > + if (ret) > > + return ret; > > + > > + ret = ti_csi2rx_v4l2_init(csi); > > + if (ret) > > + goto err_dma; > > + > > + ret = ti_csi2rx_init_vb2q(csi); > > + if (ret) > > + goto err_v4l2; > > + > > + ret = ti_csi2rx_init_subdev(csi); > > + if (ret) > > + goto err_vb2q; > > + > > + ret = of_platform_populate(csi->dev->of_node, NULL, NULL, csi->dev); > > + if (ret) { > > + dev_err(csi->dev, "Failed to create children: %d\n", ret); > > + goto err_subdev; > > + } > > + > > + return 0; > > + > > +err_subdev: > > + ti_csi2rx_cleanup_subdev(csi); > > +err_vb2q: > > + ti_csi2rx_cleanup_vb2q(csi); > > +err_v4l2: > > + ti_csi2rx_cleanup_v4l2(csi); > > +err_dma: > > + ti_csi2rx_cleanup_dma(csi); > > + return ret; > > +} > > + > > +static int ti_csi2rx_remove(struct platform_device *pdev) > > +{ > > + struct ti_csi2rx_dev *csi = platform_get_drvdata(pdev); > > + > > + if (vb2_is_busy(&csi->vidq)) > > + return -EBUSY; > > That's not right, capture should instead be stopped. Do you mean it should forcibly stop the ongoing capture by running ti_csi2rx_stop_streaming()? > > The right way to handle this is to call all the unregister functions > here, but not the cleanup functions, and to implement a real > vdev->release handler that will perform all the cleanup and kfree() the > ti_csi2rx_dev. Is this some new convention? I see most drivers setting vdev->release to either video_device_release_empty or video_device_release. No one is freeing driver specific data in vdev->release. And what if we have multiple video devices, like we would once multiplexed streams are supported. Which vdev->release would free ti_csi2rx_dev then? > > > + > > + video_unregister_device(&csi->vdev); > > + > > + ti_csi2rx_cleanup_vb2q(csi); > > + ti_csi2rx_cleanup_subdev(csi); > > + ti_csi2rx_cleanup_v4l2(csi); > > + ti_csi2rx_cleanup_dma(csi); > > + > > + return 0; > > +} > > + > > +static const struct of_device_id ti_csi2rx_of_match[] = { > > + { .compatible = "ti,j721e-csi2rx", }, > > + { }, > > +}; > > +MODULE_DEVICE_TABLE(of, ti_csi2rx_of_match); > > + > > +static struct platform_driver ti_csi2rx_pdrv = { > > + .probe = ti_csi2rx_probe, > > + .remove = ti_csi2rx_remove, > > + .driver = { > > + .name = TI_CSI2RX_MODULE_NAME, > > + .of_match_table = ti_csi2rx_of_match, > > + }, > > +}; > > + > > +module_platform_driver(ti_csi2rx_pdrv); > > + > > +MODULE_DESCRIPTION("TI J721E CSI2 RX Driver"); > > +MODULE_AUTHOR("Pratyush Yadav <p.yadav@ti.com>"); > > +MODULE_LICENSE("GPL v2"); > > +MODULE_VERSION("1.0"); > > I'd drop the version, it will never change, so it's quite pointless. If > userspace needs to know if the driver implements a particular feature or > includes a bug fix, it can use the kernel version.
diff --git a/MAINTAINERS b/MAINTAINERS index 3b8fa4e5047f..2a8ebf17462e 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -19181,6 +19181,12 @@ S: Odd Fixes F: drivers/clk/ti/ F: include/linux/clk/ti.h +TI J721E CSI2RX DRIVER +M: Pratyush Yadav <p.yadav@ti.com> +L: linux-media@vger.kernel.org +S: Supported +F: drivers/media/platform/ti/j721e-csi2rx/ + TI DAVINCI MACHINE SUPPORT M: Sekhar Nori <nsekhar@ti.com> R: Bartosz Golaszewski <brgl@bgdev.pl> diff --git a/drivers/media/platform/Kconfig b/drivers/media/platform/Kconfig index 9fbdba0fd1e7..0fa58563d93b 100644 --- a/drivers/media/platform/Kconfig +++ b/drivers/media/platform/Kconfig @@ -216,6 +216,18 @@ config VIDEO_RCAR_ISP To compile this driver as a module, choose M here: the module will be called rcar-isp. +config VIDEO_TI_J721E_CSI2RX + tristate "TI J721E CSI2RX wrapper layer driver" + depends on VIDEO_DEV && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API + depends on MEDIA_SUPPORT && MEDIA_CONTROLLER + depends on PHY_CADENCE_DPHY_RX && VIDEO_CADENCE_CSI2RX + depends on ARCH_K3 || COMPILE_TEST + select VIDEOBUF2_DMA_CONTIG + select V4L2_FWNODE + help + Support for TI CSI2RX wrapper layer. This just enables the wrapper driver. + The Cadence CSI2RX bridge driver needs to be enabled separately. + endif # V4L_PLATFORM_DRIVERS menuconfig V4L_MEM2MEM_DRIVERS diff --git a/drivers/media/platform/ti/Makefile b/drivers/media/platform/ti/Makefile index bbc737ccbbea..17c9cfb74f66 100644 --- a/drivers/media/platform/ti/Makefile +++ b/drivers/media/platform/ti/Makefile @@ -1,3 +1,4 @@ # SPDX-License-Identifier: GPL-2.0 obj-y += cal/ obj-y += vpe/ +obj-y += j721e-csi2rx/ diff --git a/drivers/media/platform/ti/j721e-csi2rx/Makefile b/drivers/media/platform/ti/j721e-csi2rx/Makefile new file mode 100644 index 000000000000..377afc1d6280 --- /dev/null +++ b/drivers/media/platform/ti/j721e-csi2rx/Makefile @@ -0,0 +1,2 @@ +# SPDX-License-Identifier: GPL-2.0 +obj-$(CONFIG_VIDEO_TI_J721E_CSI2RX) += j721e-csi2rx.o diff --git a/drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c b/drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c new file mode 100644 index 000000000000..43f31f161f43 --- /dev/null +++ b/drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c @@ -0,0 +1,913 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * TI CSI2 RX driver. + * + * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/ + * + * Author: Pratyush Yadav <p.yadav@ti.com> + */ + +#include <linux/bitfield.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/dmaengine.h> +#include <linux/of_platform.h> + +#include <media/v4l2-device.h> +#include <media/v4l2-ioctl.h> +#include <media/videobuf2-dma-contig.h> + +#define TI_CSI2RX_MODULE_NAME "j721e-csi2rx" + +#define SHIM_CNTL 0x10 +#define SHIM_CNTL_PIX_RST BIT(0) + +#define SHIM_DMACNTX 0x20 +#define SHIM_DMACNTX_EN BIT(31) +#define SHIM_DMACNTX_YUV422 GENMASK(27, 26) +#define SHIM_DMACNTX_FMT GENMASK(5, 0) +#define SHIM_DMACNTX_UYVY 0 +#define SHIM_DMACNTX_VYUY 1 +#define SHIM_DMACNTX_YUYV 2 +#define SHIM_DMACNTX_YVYU 3 + +#define SHIM_PSI_CFG0 0x24 +#define SHIM_PSI_CFG0_SRC_TAG GENMASK(15, 0) +#define SHIM_PSI_CFG0_DST_TAG GENMASK(31, 15) + +#define CSI_DF_YUV420 0x18 +#define CSI_DF_YUV422 0x1e +#define CSI_DF_RGB444 0x20 +#define CSI_DF_RGB888 0x24 + +#define PSIL_WORD_SIZE_BYTES 16 +/* + * There are no hard limits on the width or height. The DMA engine can handle + * all sizes. The max width and height are arbitrary numbers for this driver. + * Use 16M * 16M as the arbitrary limit. It is large enough that it is unlikely + * the limit will be hit in practice. + */ +#define MAX_WIDTH_BYTES SZ_16M +#define MAX_HEIGHT_BYTES SZ_16M + +struct ti_csi2rx_fmt { + u32 fourcc; /* Four character code. */ + u32 code; /* Mbus code. */ + enum v4l2_colorspace colorspace; + u32 csi_df; /* CSI Data format. */ + u8 bpp; /* Bits per pixel. */ +}; + +struct ti_csi2rx_buffer { + /* Common v4l2 buffer. Must be first. */ + struct vb2_v4l2_buffer vb; + struct list_head list; + struct ti_csi2rx_dev *csi; +}; + +enum ti_csi2rx_dma_state { + TI_CSI2RX_DMA_STOPPED, /* Streaming not started yet. */ + TI_CSI2RX_DMA_IDLE, /* Streaming but no pending DMA operation. */ + TI_CSI2RX_DMA_ACTIVE, /* Streaming and pending DMA operation. */ +}; + +struct ti_csi2rx_dma { + /* Protects all fields in this struct. */ + spinlock_t lock; + struct dma_chan *chan; + /* Buffers queued to the driver, waiting to be processed by DMA. */ + struct list_head queue; + enum ti_csi2rx_dma_state state; + /* + * Current buffer being processed by DMA. NULL if no buffer is being + * processed. + */ + struct ti_csi2rx_buffer *curr; +}; + +struct ti_csi2rx_dev { + struct device *dev; + void __iomem *shim; + struct v4l2_device v4l2_dev; + struct video_device vdev; + struct media_device mdev; + struct media_pipeline pipe; + struct media_pad pad; + struct v4l2_async_notifier notifier; + struct v4l2_subdev *subdev; + struct vb2_queue vidq; + struct mutex mutex; /* To serialize ioctls. */ + struct v4l2_format v_fmt; + struct ti_csi2rx_dma dma; + u32 sequence; +}; + +static const struct ti_csi2rx_fmt formats[] = { + { + .fourcc = V4L2_PIX_FMT_YUYV, + .code = MEDIA_BUS_FMT_YUYV8_2X8, + .colorspace = V4L2_COLORSPACE_SRGB, + .csi_df = CSI_DF_YUV422, + .bpp = 16, + }, { + .fourcc = V4L2_PIX_FMT_UYVY, + .code = MEDIA_BUS_FMT_UYVY8_2X8, + .colorspace = V4L2_COLORSPACE_SRGB, + .csi_df = CSI_DF_YUV422, + .bpp = 16, + }, { + .fourcc = V4L2_PIX_FMT_YVYU, + .code = MEDIA_BUS_FMT_YVYU8_2X8, + .colorspace = V4L2_COLORSPACE_SRGB, + .csi_df = CSI_DF_YUV422, + .bpp = 16, + }, { + .fourcc = V4L2_PIX_FMT_VYUY, + .code = MEDIA_BUS_FMT_VYUY8_2X8, + .colorspace = V4L2_COLORSPACE_SRGB, + .csi_df = CSI_DF_YUV422, + .bpp = 16, + }, + + /* More formats can be supported but they are not listed for now. */ +}; + +static const unsigned int num_formats = ARRAY_SIZE(formats); + +/* Forward declaration needed by ti_csi2rx_dma_callback. */ +static int ti_csi2rx_start_dma(struct ti_csi2rx_dev *csi, + struct ti_csi2rx_buffer *buf); + +static const struct ti_csi2rx_fmt *find_format_by_pix(u32 pixelformat) +{ + unsigned int i; + + for (i = 0; i < num_formats; i++) { + if (formats[i].fourcc == pixelformat) + return &formats[i]; + } + + return NULL; +} + +static void ti_csi2rx_fill_fmt(const struct ti_csi2rx_fmt *csi_fmt, + struct v4l2_format *v4l2_fmt) +{ + struct v4l2_pix_format *pix = &v4l2_fmt->fmt.pix; + u32 bpl; + + v4l2_fmt->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; + pix->pixelformat = csi_fmt->fourcc; + pix->colorspace = csi_fmt->colorspace; + pix->sizeimage = pix->height * pix->width * (csi_fmt->bpp / 8); + + bpl = (pix->width * ALIGN(csi_fmt->bpp, 8)) >> 3; + pix->bytesperline = ALIGN(bpl, 16); +} + +static int ti_csi2rx_querycap(struct file *file, void *priv, + struct v4l2_capability *cap) +{ + struct ti_csi2rx_dev *csi = video_drvdata(file); + + strscpy(cap->driver, TI_CSI2RX_MODULE_NAME, sizeof(cap->driver)); + strscpy(cap->card, TI_CSI2RX_MODULE_NAME, sizeof(cap->card)); + + snprintf(cap->bus_info, sizeof(cap->bus_info), "platform:%s", + dev_name(csi->dev)); + + return 0; +} + +static int ti_csi2rx_enum_fmt_vid_cap(struct file *file, void *priv, + struct v4l2_fmtdesc *f) +{ + if (f->index >= num_formats) + return -EINVAL; + + memset(f->reserved, 0, sizeof(f->reserved)); + f->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; + f->pixelformat = formats[f->index].fourcc; + + return 0; +} + +static int ti_csi2rx_g_fmt_vid_cap(struct file *file, void *prov, + struct v4l2_format *f) +{ + struct ti_csi2rx_dev *csi = video_drvdata(file); + + *f = csi->v_fmt; + + return 0; +} + +static int ti_csi2rx_try_fmt_vid_cap(struct file *file, void *priv, + struct v4l2_format *f) +{ + const struct ti_csi2rx_fmt *fmt; + + /* + * Default to the first format if the requested pixel format code isn't + * supported. + */ + fmt = find_format_by_pix(f->fmt.pix.pixelformat); + if (!fmt) + fmt = &formats[0]; + + if (f->fmt.pix.field == V4L2_FIELD_ANY) + f->fmt.pix.field = V4L2_FIELD_NONE; + + if (f->fmt.pix.field != V4L2_FIELD_NONE) + return -EINVAL; + + ti_csi2rx_fill_fmt(fmt, f); + + return 0; +} + +static int ti_csi2rx_s_fmt_vid_cap(struct file *file, void *priv, + struct v4l2_format *f) +{ + struct ti_csi2rx_dev *csi = video_drvdata(file); + struct vb2_queue *q = &csi->vidq; + int ret; + + if (vb2_is_busy(q)) + return -EBUSY; + + ret = ti_csi2rx_try_fmt_vid_cap(file, priv, f); + if (ret < 0) + return ret; + + csi->v_fmt = *f; + + return 0; +} + +static int ti_csi2rx_enum_framesizes(struct file *file, void *fh, + struct v4l2_frmsizeenum *fsize) +{ + const struct ti_csi2rx_fmt *fmt; + unsigned int pixels_in_word; + u8 bpp; + + fmt = find_format_by_pix(fsize->pixel_format); + if (!fmt) + return -EINVAL; + + bpp = ALIGN(fmt->bpp, 8); + + /* + * Number of pixels in one PSI-L word. The transfer happens in multiples + * of PSI-L word sizes. + */ + pixels_in_word = PSIL_WORD_SIZE_BYTES * 8 / bpp; + + fsize->type = V4L2_FRMSIZE_TYPE_STEPWISE; + fsize->stepwise.min_width = pixels_in_word; + fsize->stepwise.max_width = rounddown(MAX_WIDTH_BYTES, pixels_in_word); + fsize->stepwise.step_width = pixels_in_word; + fsize->stepwise.min_height = 1; + fsize->stepwise.max_height = MAX_HEIGHT_BYTES; + fsize->stepwise.step_height = 1; + + return 0; +} + +static const struct v4l2_ioctl_ops csi_ioctl_ops = { + .vidioc_querycap = ti_csi2rx_querycap, + .vidioc_enum_fmt_vid_cap = ti_csi2rx_enum_fmt_vid_cap, + .vidioc_try_fmt_vid_cap = ti_csi2rx_try_fmt_vid_cap, + .vidioc_g_fmt_vid_cap = ti_csi2rx_g_fmt_vid_cap, + .vidioc_s_fmt_vid_cap = ti_csi2rx_s_fmt_vid_cap, + .vidioc_enum_framesizes = ti_csi2rx_enum_framesizes, + .vidioc_reqbufs = vb2_ioctl_reqbufs, + .vidioc_create_bufs = vb2_ioctl_create_bufs, + .vidioc_prepare_buf = vb2_ioctl_prepare_buf, + .vidioc_querybuf = vb2_ioctl_querybuf, + .vidioc_qbuf = vb2_ioctl_qbuf, + .vidioc_dqbuf = vb2_ioctl_dqbuf, + .vidioc_expbuf = vb2_ioctl_expbuf, + .vidioc_streamon = vb2_ioctl_streamon, + .vidioc_streamoff = vb2_ioctl_streamoff, +}; + +static const struct v4l2_file_operations csi_fops = { + .owner = THIS_MODULE, + .open = v4l2_fh_open, + .release = vb2_fop_release, + .read = vb2_fop_read, + .poll = vb2_fop_poll, + .unlocked_ioctl = video_ioctl2, + .mmap = vb2_fop_mmap, +}; + +static int ti_csi2rx_video_register(struct ti_csi2rx_dev *csi) +{ + struct video_device *vdev = &csi->vdev; + int ret, src_pad; + + ret = video_register_device(vdev, VFL_TYPE_VIDEO, -1); + if (ret) + return ret; + + src_pad = media_entity_get_fwnode_pad(&csi->subdev->entity, + csi->subdev->fwnode, + MEDIA_PAD_FL_SOURCE); + if (src_pad < 0) { + dev_err(csi->dev, "Couldn't find source pad for subdev\n"); + return src_pad; + } + + ret = media_create_pad_link(&csi->subdev->entity, src_pad, + &vdev->entity, 0, + MEDIA_LNK_FL_IMMUTABLE | + MEDIA_LNK_FL_ENABLED); + if (ret) { + video_unregister_device(vdev); + return ret; + } + + return 0; +} + +static int csi_async_notifier_bound(struct v4l2_async_notifier *notifier, + struct v4l2_subdev *subdev, + struct v4l2_async_subdev *asd) +{ + struct ti_csi2rx_dev *csi = dev_get_drvdata(notifier->v4l2_dev->dev); + + csi->subdev = subdev; + + return 0; +} + +static int csi_async_notifier_complete(struct v4l2_async_notifier *notifier) +{ + struct ti_csi2rx_dev *csi = dev_get_drvdata(notifier->v4l2_dev->dev); + int ret; + + ret = ti_csi2rx_video_register(csi); + if (ret) + return ret; + + return v4l2_device_register_subdev_nodes(&csi->v4l2_dev); +} + +static const struct v4l2_async_notifier_operations csi_async_notifier_ops = { + .bound = csi_async_notifier_bound, + .complete = csi_async_notifier_complete, +}; + +static int ti_csi2rx_init_subdev(struct ti_csi2rx_dev *csi) +{ + struct fwnode_handle *fwnode; + struct v4l2_async_subdev *asd; + struct device_node *node; + int ret; + + node = of_get_child_by_name(csi->dev->of_node, "csi-bridge"); + if (!node) + return -EINVAL; + + fwnode = of_fwnode_handle(node); + if (!fwnode) { + of_node_put(node); + return -EINVAL; + } + + v4l2_async_nf_init(&csi->notifier); + csi->notifier.ops = &csi_async_notifier_ops; + + asd = v4l2_async_nf_add_fwnode(&csi->notifier, fwnode, + struct v4l2_async_subdev); + of_node_put(node); + if (IS_ERR(asd)) { + v4l2_async_nf_cleanup(&csi->notifier); + return PTR_ERR(asd); + } + + ret = v4l2_async_nf_register(&csi->v4l2_dev, &csi->notifier); + if (ret) { + v4l2_async_nf_cleanup(&csi->notifier); + return ret; + } + + return 0; +} + +static void ti_csi2rx_setup_shim(struct ti_csi2rx_dev *csi) +{ + const struct ti_csi2rx_fmt *fmt; + unsigned int reg; + + fmt = find_format_by_pix(csi->v_fmt.fmt.pix.pixelformat); + if (!fmt) { + dev_err(csi->dev, "Unknown format\n"); + return; + } + + /* De-assert the pixel interface reset. */ + reg = SHIM_CNTL_PIX_RST; + writel(reg, csi->shim + SHIM_CNTL); + + reg = SHIM_DMACNTX_EN; + reg |= FIELD_PREP(SHIM_DMACNTX_FMT, fmt->csi_df); + + /* + * Using the values from the documentation gives incorrect ordering for + * the luma and chroma components. In practice, the "reverse" format + * gives the correct image. So for example, if the image is in UYVY, the + * reverse would be YVYU. + */ + switch (fmt->fourcc) { + case V4L2_PIX_FMT_UYVY: + reg |= FIELD_PREP(SHIM_DMACNTX_YUV422, + SHIM_DMACNTX_YVYU); + break; + case V4L2_PIX_FMT_VYUY: + reg |= FIELD_PREP(SHIM_DMACNTX_YUV422, + SHIM_DMACNTX_YUYV); + break; + case V4L2_PIX_FMT_YUYV: + reg |= FIELD_PREP(SHIM_DMACNTX_YUV422, + SHIM_DMACNTX_VYUY); + break; + case V4L2_PIX_FMT_YVYU: + reg |= FIELD_PREP(SHIM_DMACNTX_YUV422, + SHIM_DMACNTX_UYVY); + break; + default: + /* Ignore if not YUV 4:2:2 */ + break; + } + + writel(reg, csi->shim + SHIM_DMACNTX); + + reg = FIELD_PREP(SHIM_PSI_CFG0_SRC_TAG, 0) | + FIELD_PREP(SHIM_PSI_CFG0_DST_TAG, 1); + writel(reg, csi->shim + SHIM_PSI_CFG0); +} + +static void ti_csi2rx_dma_callback(void *param) +{ + struct ti_csi2rx_buffer *buf = param; + struct ti_csi2rx_dev *csi = buf->csi; + struct ti_csi2rx_dma *dma = &csi->dma; + unsigned long flags = 0; + + buf->vb.vb2_buf.timestamp = ktime_get_ns(); + buf->vb.sequence = csi->sequence++; + + spin_lock_irqsave(&dma->lock, flags); + + WARN_ON(dma->curr != buf); + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_DONE); + + /* If there are more buffers to process then start their transfer. */ + dma->curr = NULL; + while (!list_empty(&dma->queue)) { + buf = list_entry(dma->queue.next, struct ti_csi2rx_buffer, list); + list_del(&buf->list); + + if (ti_csi2rx_start_dma(csi, buf)) { + dev_err(csi->dev, "Failed to queue the next buffer for DMA\n"); + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR); + } else { + dma->curr = buf; + break; + } + } + + if (!dma->curr) + dma->state = TI_CSI2RX_DMA_IDLE; + + spin_unlock_irqrestore(&dma->lock, flags); +} + +static int ti_csi2rx_start_dma(struct ti_csi2rx_dev *csi, + struct ti_csi2rx_buffer *buf) +{ + unsigned long addr; + struct dma_async_tx_descriptor *desc; + size_t len = csi->v_fmt.fmt.pix.sizeimage; + dma_cookie_t cookie; + int ret = 0; + + addr = vb2_dma_contig_plane_dma_addr(&buf->vb.vb2_buf, 0); + desc = dmaengine_prep_slave_single(csi->dma.chan, addr, len, + DMA_DEV_TO_MEM, + DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + if (!desc) + return -EIO; + + desc->callback = ti_csi2rx_dma_callback; + desc->callback_param = buf; + + cookie = dmaengine_submit(desc); + ret = dma_submit_error(cookie); + if (ret) + return ret; + + dma_async_issue_pending(csi->dma.chan); + + return 0; +} + +static int ti_csi2rx_queue_setup(struct vb2_queue *q, unsigned int *nbuffers, + unsigned int *nplanes, unsigned int sizes[], + struct device *alloc_devs[]) +{ + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(q); + unsigned int size = csi->v_fmt.fmt.pix.sizeimage; + + if (*nplanes) { + if (sizes[0] < size) + return -EINVAL; + size = sizes[0]; + } + + *nplanes = 1; + sizes[0] = size; + + return 0; +} + +static int ti_csi2rx_buffer_prepare(struct vb2_buffer *vb) +{ + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(vb->vb2_queue); + unsigned long size = csi->v_fmt.fmt.pix.sizeimage; + + if (vb2_plane_size(vb, 0) < size) { + dev_err(csi->dev, "Data will not fit into plane\n"); + return -EINVAL; + } + + vb2_set_plane_payload(vb, 0, size); + return 0; +} + +static void ti_csi2rx_buffer_queue(struct vb2_buffer *vb) +{ + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(vb->vb2_queue); + struct ti_csi2rx_buffer *buf; + struct ti_csi2rx_dma *dma = &csi->dma; + unsigned long flags = 0; + int ret; + + buf = container_of(vb, struct ti_csi2rx_buffer, vb.vb2_buf); + buf->csi = csi; + + spin_lock_irqsave(&dma->lock, flags); + /* + * Usually the DMA callback takes care of queueing the pending buffers. + * But if DMA has stalled due to lack of buffers, restart it now. + */ + if (dma->state == TI_CSI2RX_DMA_IDLE) { + ret = ti_csi2rx_start_dma(csi, buf); + if (ret) { + dev_err(csi->dev, "Failed to start DMA: %d\n", ret); + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED); + goto unlock; + } + + dma->curr = buf; + dma->state = TI_CSI2RX_DMA_ACTIVE; + } else { + list_add_tail(&buf->list, &dma->queue); + } + +unlock: + spin_unlock_irqrestore(&dma->lock, flags); +} + +static int ti_csi2rx_start_streaming(struct vb2_queue *vq, unsigned int count) +{ + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(vq); + struct ti_csi2rx_dma *dma = &csi->dma; + struct ti_csi2rx_buffer *buf, *tmp; + unsigned long flags; + int ret = 0; + + spin_lock_irqsave(&dma->lock, flags); + if (list_empty(&dma->queue)) + ret = -EIO; + spin_unlock_irqrestore(&dma->lock, flags); + if (ret) + return ret; + + ret = media_pipeline_start(&csi->vdev.entity, &csi->pipe); + if (ret) + goto err; + + ti_csi2rx_setup_shim(csi); + + ret = v4l2_subdev_call(csi->subdev, video, s_stream, 1); + if (ret) + goto err_pipeline; + + csi->sequence = 0; + + spin_lock_irqsave(&dma->lock, flags); + buf = list_entry(dma->queue.next, struct ti_csi2rx_buffer, list); + list_del(&buf->list); + dma->state = TI_CSI2RX_DMA_ACTIVE; + + ret = ti_csi2rx_start_dma(csi, buf); + if (ret) { + dev_err(csi->dev, "Failed to start DMA: %d\n", ret); + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED); + spin_unlock_irqrestore(&dma->lock, flags); + goto err_stream; + } + + dma->curr = buf; + spin_unlock_irqrestore(&dma->lock, flags); + + return 0; + +err_stream: + v4l2_subdev_call(csi->subdev, video, s_stream, 0); +err_pipeline: + media_pipeline_stop(&csi->vdev.entity); +err: + spin_lock_irqsave(&dma->lock, flags); + list_for_each_entry_safe(buf, tmp, &dma->queue, list) { + list_del(&buf->list); + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED); + } + csi->dma.state = TI_CSI2RX_DMA_STOPPED; + spin_unlock_irqrestore(&dma->lock, flags); + + return ret; +} + +static void ti_csi2rx_stop_streaming(struct vb2_queue *vq) +{ + struct ti_csi2rx_dev *csi = vb2_get_drv_priv(vq); + struct ti_csi2rx_buffer *buf = NULL, *tmp; + struct ti_csi2rx_dma *dma = &csi->dma; + unsigned long flags = 0; + int ret; + + media_pipeline_stop(&csi->vdev.entity); + + ret = v4l2_subdev_call(csi->subdev, video, s_stream, 0); + if (ret) + dev_err(csi->dev, "Failed to stop subdev stream\n"); + + writel(0, csi->shim + SHIM_CNTL); + + ret = dmaengine_terminate_sync(csi->dma.chan); + if (ret) + dev_err(csi->dev, "Failed to stop DMA\n"); + + writel(0, csi->shim + SHIM_DMACNTX); + + spin_lock_irqsave(&dma->lock, flags); + list_for_each_entry_safe(buf, tmp, &csi->dma.queue, list) { + list_del(&buf->list); + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR); + } + + if (dma->curr) + vb2_buffer_done(&dma->curr->vb.vb2_buf, VB2_BUF_STATE_ERROR); + + dma->curr = NULL; + dma->state = TI_CSI2RX_DMA_STOPPED; + spin_unlock_irqrestore(&dma->lock, flags); +} + +static const struct vb2_ops csi_vb2_qops = { + .queue_setup = ti_csi2rx_queue_setup, + .buf_prepare = ti_csi2rx_buffer_prepare, + .buf_queue = ti_csi2rx_buffer_queue, + .start_streaming = ti_csi2rx_start_streaming, + .stop_streaming = ti_csi2rx_stop_streaming, + .wait_prepare = vb2_ops_wait_prepare, + .wait_finish = vb2_ops_wait_finish, +}; + +static int ti_csi2rx_init_vb2q(struct ti_csi2rx_dev *csi) +{ + struct vb2_queue *q = &csi->vidq; + int ret; + + q->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; + q->io_modes = VB2_MMAP | VB2_USERPTR | VB2_DMABUF | VB2_READ; + q->drv_priv = csi; + q->buf_struct_size = sizeof(struct ti_csi2rx_buffer); + q->ops = &csi_vb2_qops; + q->mem_ops = &vb2_dma_contig_memops; + q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC; + q->dev = dmaengine_get_dma_device(csi->dma.chan); + q->lock = &csi->mutex; + + ret = vb2_queue_init(q); + if (ret) + return ret; + + csi->vdev.queue = q; + + return 0; +} + +static int ti_csi2rx_init_dma(struct ti_csi2rx_dev *csi) +{ + struct dma_slave_config cfg; + int ret; + + INIT_LIST_HEAD(&csi->dma.queue); + spin_lock_init(&csi->dma.lock); + + csi->dma.state = TI_CSI2RX_DMA_STOPPED; + + csi->dma.chan = dma_request_chan(csi->dev, "rx0"); + if (IS_ERR(csi->dma.chan)) + return PTR_ERR(csi->dma.chan); + + memset(&cfg, 0, sizeof(cfg)); + + cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_16_BYTES; + + ret = dmaengine_slave_config(csi->dma.chan, &cfg); + if (ret) + return ret; + + return 0; +} + +static int ti_csi2rx_v4l2_init(struct ti_csi2rx_dev *csi) +{ + struct media_device *mdev = &csi->mdev; + struct video_device *vdev = &csi->vdev; + const struct ti_csi2rx_fmt *fmt; + struct v4l2_pix_format *pix_fmt = &csi->v_fmt.fmt.pix; + int ret; + + fmt = find_format_by_pix(V4L2_PIX_FMT_UYVY); + if (!fmt) + return -EINVAL; + + pix_fmt->width = 640; + pix_fmt->height = 480; + + ti_csi2rx_fill_fmt(fmt, &csi->v_fmt); + + mdev->dev = csi->dev; + mdev->hw_revision = 1; + strscpy(mdev->model, "TI-CSI2RX", sizeof(mdev->model)); + snprintf(mdev->bus_info, sizeof(mdev->bus_info), "platform:%s", + dev_name(mdev->dev)); + + media_device_init(mdev); + + strscpy(vdev->name, TI_CSI2RX_MODULE_NAME, sizeof(vdev->name)); + vdev->v4l2_dev = &csi->v4l2_dev; + vdev->vfl_dir = VFL_DIR_RX; + vdev->fops = &csi_fops; + vdev->ioctl_ops = &csi_ioctl_ops; + vdev->release = video_device_release_empty; + vdev->device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_READWRITE | + V4L2_CAP_STREAMING | V4L2_CAP_IO_MC; + vdev->lock = &csi->mutex; + video_set_drvdata(vdev, csi); + + csi->pad.flags = MEDIA_PAD_FL_SINK; + ret = media_entity_pads_init(&csi->vdev.entity, 1, &csi->pad); + if (ret) + return ret; + + csi->v4l2_dev.mdev = mdev; + + ret = v4l2_device_register(csi->dev, &csi->v4l2_dev); + if (ret) + return ret; + + ret = media_device_register(mdev); + if (ret) { + v4l2_device_unregister(&csi->v4l2_dev); + media_device_cleanup(mdev); + return ret; + } + + return 0; +} + +static void ti_csi2rx_cleanup_dma(struct ti_csi2rx_dev *csi) +{ + dma_release_channel(csi->dma.chan); +} + +static void ti_csi2rx_cleanup_v4l2(struct ti_csi2rx_dev *csi) +{ + media_device_unregister(&csi->mdev); + v4l2_device_unregister(&csi->v4l2_dev); + media_device_cleanup(&csi->mdev); +} + +static void ti_csi2rx_cleanup_subdev(struct ti_csi2rx_dev *csi) +{ + v4l2_async_nf_unregister(&csi->notifier); + v4l2_async_nf_cleanup(&csi->notifier); +} + +static void ti_csi2rx_cleanup_vb2q(struct ti_csi2rx_dev *csi) +{ + vb2_queue_release(&csi->vidq); +} + +static int ti_csi2rx_probe(struct platform_device *pdev) +{ + struct ti_csi2rx_dev *csi; + struct resource *res; + int ret; + + csi = devm_kzalloc(&pdev->dev, sizeof(*csi), GFP_KERNEL); + if (!csi) + return -ENOMEM; + + csi->dev = &pdev->dev; + platform_set_drvdata(pdev, csi); + + mutex_init(&csi->mutex); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + csi->shim = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(csi->shim)) + return PTR_ERR(csi->shim); + + ret = ti_csi2rx_init_dma(csi); + if (ret) + return ret; + + ret = ti_csi2rx_v4l2_init(csi); + if (ret) + goto err_dma; + + ret = ti_csi2rx_init_vb2q(csi); + if (ret) + goto err_v4l2; + + ret = ti_csi2rx_init_subdev(csi); + if (ret) + goto err_vb2q; + + ret = of_platform_populate(csi->dev->of_node, NULL, NULL, csi->dev); + if (ret) { + dev_err(csi->dev, "Failed to create children: %d\n", ret); + goto err_subdev; + } + + return 0; + +err_subdev: + ti_csi2rx_cleanup_subdev(csi); +err_vb2q: + ti_csi2rx_cleanup_vb2q(csi); +err_v4l2: + ti_csi2rx_cleanup_v4l2(csi); +err_dma: + ti_csi2rx_cleanup_dma(csi); + return ret; +} + +static int ti_csi2rx_remove(struct platform_device *pdev) +{ + struct ti_csi2rx_dev *csi = platform_get_drvdata(pdev); + + if (vb2_is_busy(&csi->vidq)) + return -EBUSY; + + video_unregister_device(&csi->vdev); + + ti_csi2rx_cleanup_vb2q(csi); + ti_csi2rx_cleanup_subdev(csi); + ti_csi2rx_cleanup_v4l2(csi); + ti_csi2rx_cleanup_dma(csi); + + return 0; +} + +static const struct of_device_id ti_csi2rx_of_match[] = { + { .compatible = "ti,j721e-csi2rx", }, + { }, +}; +MODULE_DEVICE_TABLE(of, ti_csi2rx_of_match); + +static struct platform_driver ti_csi2rx_pdrv = { + .probe = ti_csi2rx_probe, + .remove = ti_csi2rx_remove, + .driver = { + .name = TI_CSI2RX_MODULE_NAME, + .of_match_table = ti_csi2rx_of_match, + }, +}; + +module_platform_driver(ti_csi2rx_pdrv); + +MODULE_DESCRIPTION("TI J721E CSI2 RX Driver"); +MODULE_AUTHOR("Pratyush Yadav <p.yadav@ti.com>"); +MODULE_LICENSE("GPL v2"); +MODULE_VERSION("1.0");
TI's J721E uses the Cadence CSI2RX and DPHY peripherals to facilitate capture over a CSI-2 bus. The Cadence CSI2RX IP acts as a bridge between the TI specific parts and the CSI-2 protocol parts. TI then has a wrapper on top of this bridge called the SHIM layer. It takes in data from stream 0, repacks it, and sends it to memory over PSI-L DMA. This driver acts as the "front end" to V4L2 client applications. It implements the required ioctls and buffer operations, passes the necessary calls on to the bridge, programs the SHIM layer, and performs DMA via the dmaengine API to finally return the data to a buffer supplied by the application. Signed-off-by: Pratyush Yadav <p.yadav@ti.com> --- (no changes since v5) Changes in v5: - Add dependency on PHY_CADENCE_DPHY_RX instead of PHY_CADENCE_DPHY since the Rx mode DPHY now has a separate driver. - Drop ti_csi2rx_validate_pipeline(). Pipeline validation should be done at media_pipeline_start(). - Do not assign flags. - Fix error handling in ti_csi2rx_start_streaming(). Free up vb2 buffers when media_pipeline_start() fails. Changes in v4: - Acquire the media device's graph_mutex before starting the graph walk. - Call media_graph_walk_init() and media_graph_walk_cleanup() when starting and ending the graph walk respectively. - Reduce max frame height and width in enum_framesizes. Currently they are set to UINT_MAX but they must be a multiple of step_width, so they need to be rounded down. Also, these values are absurdly large which causes some userspace applications like gstreamer to trip up. While it is not generally right to change the kernel for an application bug, it is not such a big deal here. This change is replacing one set of absurdly large arbitrary values with another set of smaller but still absurdly large arbitrary values. Both limits are unlikely to be hit in practice. Changes in v3: - Move DMA related fields in struct ti_csi2rx_dma. - Protect DMA buffer queue with a spinlock to make sure the queue buffer and DMA callback don't race on it. - Track the current DMA state. It might go idle because of a lack of buffers. This state can be used to restart it if needed. - Do not include the current buffer in the pending queue. It is slightly better modelling than leaving it at the head of the pending queue. - Use the buffer as the callback argument, and add a reference to csi in it. - If queueing a buffer to DMA fails, the buffer gets leaked and DMA gets stalled with. Instead, report the error to vb2 and queue the next buffer in the pending queue. - DMA gets stalled if we run out of buffers since the callback is the only one that fires subsequent transfers and it is no longer being called. Check for that when queueing buffers and restart DMA if needed. - Do not put of node until we are done using the fwnode. - Set inital format to UYVY 640x480. Changes in v2: - Use dmaengine_get_dma_device() instead of directly accessing dma->device->dev. - Do not set dst_addr_width when configuring slave DMA. - Move to a separate subdir and rename to j721e-csi2rx.c - Convert compatible to ti,j721e-csi2rx. - Move to use Media Controller centric APIs. - Improve cleanup in probe when one of the steps fails. - Add colorspace to formats database. - Set hw_revision on media_device. - Move video device initialization to probe time instead of register time. MAINTAINERS | 6 + drivers/media/platform/Kconfig | 12 + drivers/media/platform/ti/Makefile | 1 + .../media/platform/ti/j721e-csi2rx/Makefile | 2 + .../platform/ti/j721e-csi2rx/j721e-csi2rx.c | 913 ++++++++++++++++++ 5 files changed, 934 insertions(+) create mode 100644 drivers/media/platform/ti/j721e-csi2rx/Makefile create mode 100644 drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c