new file mode 100644
@@ -0,0 +1,533 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2013 - 2023 Intel Corporation
+ */
+
+#include <linux/bitfield.h>
+#include <linux/delay.h>
+#include <linux/iopoll.h>
+
+#include "ipu6-isys.h"
+#include "ipu6-platform-isys-csi2-reg.h"
+#include "ipu6-platform-regs.h"
+
+#define IPU6_DWC_DPHY_BASE(i) (0x238038 + 0x34 * (i))
+#define IPU6_DWC_DPHY_RSTZ 0x00
+#define IPU6_DWC_DPHY_SHUTDOWNZ 0x04
+#define IPU6_DWC_DPHY_HSFREQRANGE 0x08
+#define IPU6_DWC_DPHY_CFGCLKFREQRANGE 0x0c
+#define IPU6_DWC_DPHY_TEST_IFC_ACCESS_MODE 0x10
+#define IPU6_DWC_DPHY_TEST_IFC_REQ 0x14
+#define IPU6_DWC_DPHY_TEST_IFC_REQ_COMPLETION 0x18
+#define IPU6_DWC_DPHY_DFT_CTRL0 0x28
+#define IPU6_DWC_DPHY_DFT_CTRL1 0x2c
+#define IPU6_DWC_DPHY_DFT_CTRL2 0x30
+
+/*
+ * test IFC request definition:
+ * - req: 0 for read, 1 for write
+ * - 12 bits address
+ * - 8bits data (will ignore for read)
+ * --24----16------4-----0
+ * --|-data-|-addr-|-req-|
+ */
+#define IFC_REQ(req, addr, data) (FIELD_PREP(GENMASK(23, 16), data) | \
+ FIELD_PREP(GENMASK(15, 4), addr) | \
+ FIELD_PREP(GENMASK(1, 0), req))
+
+#define TEST_IFC_REQ_READ 0
+#define TEST_IFC_REQ_WRITE 1
+#define TEST_IFC_REQ_RESET 2
+
+#define TEST_IFC_ACCESS_MODE_FSM 0
+#define TEST_IFC_ACCESS_MODE_IFC_CTL 1
+
+enum phy_fsm_state {
+ PHY_FSM_STATE_POWERON = 0,
+ PHY_FSM_STATE_BGPON = 1,
+ PHY_FSM_STATE_CAL_TYPE = 2,
+ PHY_FSM_STATE_BURNIN_CAL = 3,
+ PHY_FSM_STATE_TERMCAL = 4,
+ PHY_FSM_STATE_OFFSETCAL = 5,
+ PHY_FSM_STATE_OFFSET_LANE = 6,
+ PHY_FSM_STATE_IDLE = 7,
+ PHY_FSM_STATE_ULP = 8,
+ PHY_FSM_STATE_DDLTUNNING = 9,
+ PHY_FSM_STATE_SKEW_BACKWARD = 10,
+ PHY_FSM_STATE_INVALID,
+};
+
+static void dwc_dphy_write(struct ipu6_isys *isys, u32 phy_id, u32 addr,
+ u32 data)
+{
+ struct device *dev = &isys->adev->auxdev.dev;
+ void __iomem *isys_base = isys->pdata->base;
+ void __iomem *base = isys_base + IPU6_DWC_DPHY_BASE(phy_id);
+
+ dev_dbg(dev, "write: reg 0x%lx = data 0x%x", base + addr - isys_base,
+ data);
+ writel(data, base + addr);
+}
+
+static u32 dwc_dphy_read(struct ipu6_isys *isys, u32 phy_id, u32 addr)
+{
+ struct device *dev = &isys->adev->auxdev.dev;
+ void __iomem *isys_base = isys->pdata->base;
+ void __iomem *base = isys_base + IPU6_DWC_DPHY_BASE(phy_id);
+ u32 data;
+
+ data = readl(base + addr);
+ dev_dbg(dev, "read: reg 0x%lx = data 0x%x", base + addr - isys_base,
+ data);
+
+ return data;
+}
+
+static void dwc_dphy_write_mask(struct ipu6_isys *isys, u32 phy_id, u32 addr,
+ u32 data, u8 shift, u8 width)
+{
+ u32 temp;
+ u32 mask;
+
+ mask = (1 << width) - 1;
+ temp = dwc_dphy_read(isys, phy_id, addr);
+ temp &= ~(mask << shift);
+ temp |= (data & mask) << shift;
+ dwc_dphy_write(isys, phy_id, addr, temp);
+}
+
+static u32 __maybe_unused dwc_dphy_read_mask(struct ipu6_isys *isys, u32 phy_id,
+ u32 addr, u8 shift, u8 width)
+{
+ u32 val;
+
+ val = dwc_dphy_read(isys, phy_id, addr) >> shift;
+ return val & ((1 << width) - 1);
+}
+
+#define DWC_DPHY_TIMEOUT (5 * USEC_PER_SEC)
+static int dwc_dphy_ifc_read(struct ipu6_isys *isys, u32 phy_id, u32 addr,
+ u32 *val)
+{
+ struct device *dev = &isys->adev->auxdev.dev;
+ void __iomem *isys_base = isys->pdata->base;
+ void __iomem *base = isys_base + IPU6_DWC_DPHY_BASE(phy_id);
+ void __iomem *reg;
+ u32 completion;
+ int ret;
+
+ dwc_dphy_write(isys, phy_id, IPU6_DWC_DPHY_TEST_IFC_REQ,
+ IFC_REQ(TEST_IFC_REQ_READ, addr, 0));
+ reg = base + IPU6_DWC_DPHY_TEST_IFC_REQ_COMPLETION;
+ ret = readl_poll_timeout(reg, completion, !(completion & BIT(0)),
+ 10, DWC_DPHY_TIMEOUT);
+ if (ret) {
+ dev_err(dev, "DWC ifc request read timeout\n");
+ return ret;
+ }
+
+ *val = completion >> 8 & 0xff;
+ *val = FIELD_GET(GENMASK(15, 8), completion);
+ dev_dbg(dev, "DWC ifc read 0x%x = 0x%x", addr, *val);
+
+ return 0;
+}
+
+static int dwc_dphy_ifc_write(struct ipu6_isys *isys, u32 phy_id, u32 addr,
+ u32 data)
+{
+ struct device *dev = &isys->adev->auxdev.dev;
+ void __iomem *isys_base = isys->pdata->base;
+ void __iomem *base = isys_base + IPU6_DWC_DPHY_BASE(phy_id);
+ void __iomem *reg;
+ u32 completion;
+ int ret;
+
+ dwc_dphy_write(isys, phy_id, IPU6_DWC_DPHY_TEST_IFC_REQ,
+ IFC_REQ(TEST_IFC_REQ_WRITE, addr, data));
+ completion = readl(base + IPU6_DWC_DPHY_TEST_IFC_REQ_COMPLETION);
+ reg = base + IPU6_DWC_DPHY_TEST_IFC_REQ_COMPLETION;
+ ret = readl_poll_timeout(reg, completion, !(completion & BIT(0)),
+ 10, DWC_DPHY_TIMEOUT);
+ if (ret)
+ dev_err(dev, "DWC ifc request write timeout\n");
+
+ return ret;
+}
+
+static void dwc_dphy_ifc_write_mask(struct ipu6_isys *isys, u32 phy_id,
+ u32 addr, u32 data, u8 shift, u8 width)
+{
+ u32 temp, mask;
+ int ret;
+
+ ret = dwc_dphy_ifc_read(isys, phy_id, addr, &temp);
+ if (ret)
+ return;
+
+ mask = (1 << width) - 1;
+ temp &= ~(mask << shift);
+ temp |= (data & mask) << shift;
+ dwc_dphy_ifc_write(isys, phy_id, addr, temp);
+}
+
+static u32 dwc_dphy_ifc_read_mask(struct ipu6_isys *isys, u32 phy_id, u32 addr,
+ u8 shift, u8 width)
+{
+ int ret;
+ u32 val;
+
+ ret = dwc_dphy_ifc_read(isys, phy_id, addr, &val);
+ if (ret)
+ return 0;
+
+ return ((val >> shift) & ((1 << width) - 1));
+}
+
+static int dwc_dphy_pwr_up(struct ipu6_isys *isys, u32 phy_id)
+{
+ struct device *dev = &isys->adev->auxdev.dev;
+ u32 fsm_state;
+ int ret;
+
+ dwc_dphy_write(isys, phy_id, IPU6_DWC_DPHY_RSTZ, 1);
+ usleep_range(10, 20);
+ dwc_dphy_write(isys, phy_id, IPU6_DWC_DPHY_SHUTDOWNZ, 1);
+
+ ret = read_poll_timeout(dwc_dphy_ifc_read_mask, fsm_state,
+ (fsm_state == PHY_FSM_STATE_IDLE ||
+ fsm_state == PHY_FSM_STATE_ULP),
+ 100, DWC_DPHY_TIMEOUT, false, isys,
+ phy_id, 0x1e, 0, 4);
+
+ if (ret)
+ dev_err(dev, "Dphy %d power up failed, state 0x%x", phy_id,
+ fsm_state);
+
+ return ret;
+}
+
+struct dwc_dphy_freq_range {
+ u8 hsfreq;
+ u16 min;
+ u16 max;
+ u16 default_mbps;
+ u16 osc_freq_target;
+};
+
+#define DPHY_FREQ_RANGE_NUM (63)
+#define DPHY_FREQ_RANGE_INVALID_INDEX (0xff)
+static const struct dwc_dphy_freq_range freqranges[DPHY_FREQ_RANGE_NUM] = {
+ {0x00, 80, 97, 80, 335},
+ {0x10, 80, 107, 90, 335},
+ {0x20, 84, 118, 100, 335},
+ {0x30, 93, 128, 110, 335},
+ {0x01, 103, 139, 120, 335},
+ {0x11, 112, 149, 130, 335},
+ {0x21, 122, 160, 140, 335},
+ {0x31, 131, 170, 150, 335},
+ {0x02, 141, 181, 160, 335},
+ {0x12, 150, 191, 170, 335},
+ {0x22, 160, 202, 180, 335},
+ {0x32, 169, 212, 190, 335},
+ {0x03, 183, 228, 205, 335},
+ {0x13, 198, 244, 220, 335},
+ {0x23, 212, 259, 235, 335},
+ {0x33, 226, 275, 250, 335},
+ {0x04, 250, 301, 275, 335},
+ {0x14, 274, 328, 300, 335},
+ {0x25, 297, 354, 325, 335},
+ {0x35, 321, 380, 350, 335},
+ {0x05, 369, 433, 400, 335},
+ {0x16, 416, 485, 450, 335},
+ {0x26, 464, 538, 500, 335},
+ {0x37, 511, 590, 550, 335},
+ {0x07, 559, 643, 600, 335},
+ {0x18, 606, 695, 650, 335},
+ {0x28, 654, 748, 700, 335},
+ {0x39, 701, 800, 750, 335},
+ {0x09, 749, 853, 800, 335},
+ {0x19, 796, 905, 850, 335},
+ {0x29, 844, 958, 900, 335},
+ {0x3a, 891, 1010, 950, 335},
+ {0x0a, 939, 1063, 1000, 335},
+ {0x1a, 986, 1115, 1050, 335},
+ {0x2a, 1034, 1168, 1100, 335},
+ {0x3b, 1081, 1220, 1150, 335},
+ {0x0b, 1129, 1273, 1200, 335},
+ {0x1b, 1176, 1325, 1250, 335},
+ {0x2b, 1224, 1378, 1300, 335},
+ {0x3c, 1271, 1430, 1350, 335},
+ {0x0c, 1319, 1483, 1400, 335},
+ {0x1c, 1366, 1535, 1450, 335},
+ {0x2c, 1414, 1588, 1500, 335},
+ {0x3d, 1461, 1640, 1550, 208},
+ {0x0d, 1509, 1693, 1600, 214},
+ {0x1d, 1556, 1745, 1650, 221},
+ {0x2e, 1604, 1798, 1700, 228},
+ {0x3e, 1651, 1850, 1750, 234},
+ {0x0e, 1699, 1903, 1800, 241},
+ {0x1e, 1746, 1955, 1850, 248},
+ {0x2f, 1794, 2008, 1900, 255},
+ {0x3f, 1841, 2060, 1950, 261},
+ {0x0f, 1889, 2113, 2000, 268},
+ {0x40, 1936, 2165, 2050, 275},
+ {0x41, 1984, 2218, 2100, 281},
+ {0x42, 2031, 2270, 2150, 288},
+ {0x43, 2079, 2323, 2200, 294},
+ {0x44, 2126, 2375, 2250, 302},
+ {0x45, 2174, 2428, 2300, 308},
+ {0x46, 2221, 2480, 2350, 315},
+ {0x47, 2269, 2500, 2400, 321},
+ {0x48, 2316, 2500, 2450, 328},
+ {0x49, 2364, 2500, 2500, 335}
+};
+
+static u16 get_hsfreq_by_mbps(u32 mbps)
+{
+ unsigned int i = DPHY_FREQ_RANGE_NUM;
+
+ while (i--) {
+ if (freqranges[i].default_mbps == mbps ||
+ (mbps >= freqranges[i].min && mbps <= freqranges[i].max))
+ return i;
+ }
+
+ return DPHY_FREQ_RANGE_INVALID_INDEX;
+}
+
+static int ipu6_isys_dwc_phy_config(struct ipu6_isys *isys,
+ u32 phy_id, u32 mbps)
+{
+ struct ipu6_bus_device *adev = isys->adev;
+ struct device *dev = &adev->auxdev.dev;
+ struct ipu6_device *isp = adev->isp;
+ u32 cfg_clk_freqrange;
+ u32 osc_freq_target;
+ u32 index;
+
+ dev_dbg(dev, "config Dphy %u with %u mbps", phy_id, mbps);
+
+ index = get_hsfreq_by_mbps(mbps);
+ if (index == DPHY_FREQ_RANGE_INVALID_INDEX) {
+ dev_err(dev, "link freq not found for mbps %u", mbps);
+ return -EINVAL;
+ }
+
+ dwc_dphy_write_mask(isys, phy_id, IPU6_DWC_DPHY_HSFREQRANGE,
+ freqranges[index].hsfreq, 0, 7);
+
+ /* Force termination Calibration */
+ if (isys->phy_termcal_val) {
+ dwc_dphy_ifc_write_mask(isys, phy_id, 0x20a, 0x1, 0, 1);
+ dwc_dphy_ifc_write_mask(isys, phy_id, 0x209, 0x3, 0, 2);
+ dwc_dphy_ifc_write_mask(isys, phy_id, 0x209,
+ isys->phy_termcal_val, 4, 4);
+ }
+
+ /*
+ * Enable override to configure the DDL target oscillation
+ * frequency on bit 0 of register 0xe4
+ */
+ dwc_dphy_ifc_write_mask(isys, phy_id, 0xe4, 0x1, 0, 1);
+ /*
+ * configure registers 0xe2, 0xe3 with the
+ * appropriate DDL target oscillation frequency
+ * 0x1cc(460)
+ */
+ osc_freq_target = freqranges[index].osc_freq_target;
+ dwc_dphy_ifc_write_mask(isys, phy_id, 0xe2,
+ osc_freq_target & 0xff, 0, 8);
+ dwc_dphy_ifc_write_mask(isys, phy_id, 0xe3,
+ (osc_freq_target >> 8) & 0xf, 0, 4);
+
+ if (mbps < 1500) {
+ /* deskew_polarity_rw, for < 1.5Gbps */
+ dwc_dphy_ifc_write_mask(isys, phy_id, 0x8, 0x1, 5, 1);
+ }
+
+ /*
+ * Set cfgclkfreqrange[5:0] = round[(Fcfg_clk(MHz)-17)*4]
+ * (38.4 - 17) * 4 = ~85 (0x55)
+ */
+ cfg_clk_freqrange = (isp->buttress.ref_clk - 170) * 4 / 10;
+ dev_dbg(dev, "ref_clk = %u clk_freqrange = %u",
+ isp->buttress.ref_clk, cfg_clk_freqrange);
+ dwc_dphy_write_mask(isys, phy_id, IPU6_DWC_DPHY_CFGCLKFREQRANGE,
+ cfg_clk_freqrange, 0, 8);
+
+ dwc_dphy_write_mask(isys, phy_id, IPU6_DWC_DPHY_DFT_CTRL2, 0x1, 4, 1);
+ dwc_dphy_write_mask(isys, phy_id, IPU6_DWC_DPHY_DFT_CTRL2, 0x1, 8, 1);
+
+ return 0;
+}
+
+static void ipu6_isys_dwc_phy_aggr_setup(struct ipu6_isys *isys, u32 master,
+ u32 slave, u32 mbps)
+{
+ /* Config mastermacro */
+ dwc_dphy_ifc_write_mask(isys, master, 0x133, 0x1, 0, 1);
+ dwc_dphy_ifc_write_mask(isys, slave, 0x133, 0x0, 0, 1);
+
+ /* Config master PHY clk lane to drive long channel clk */
+ dwc_dphy_ifc_write_mask(isys, master, 0x307, 0x1, 2, 1);
+ dwc_dphy_ifc_write_mask(isys, slave, 0x307, 0x0, 2, 1);
+
+ /* Config both PHYs data lanes to get clk from long channel */
+ dwc_dphy_ifc_write_mask(isys, master, 0x508, 0x1, 5, 1);
+ dwc_dphy_ifc_write_mask(isys, slave, 0x508, 0x1, 5, 1);
+ dwc_dphy_ifc_write_mask(isys, master, 0x708, 0x1, 5, 1);
+ dwc_dphy_ifc_write_mask(isys, slave, 0x708, 0x1, 5, 1);
+
+ /* Config slave PHY clk lane to bypass long channel clk to DDR clk */
+ dwc_dphy_ifc_write_mask(isys, master, 0x308, 0x0, 3, 1);
+ dwc_dphy_ifc_write_mask(isys, slave, 0x308, 0x1, 3, 1);
+
+ /* Override slave PHY clk lane enable (DPHYRXCLK_CLL_demux module) */
+ dwc_dphy_ifc_write_mask(isys, slave, 0xe0, 0x3, 0, 2);
+
+ /* Override slave PHY DDR clk lane enable (DPHYHSRX_div124 module) */
+ dwc_dphy_ifc_write_mask(isys, slave, 0xe1, 0x1, 1, 1);
+ dwc_dphy_ifc_write_mask(isys, slave, 0x307, 0x1, 3, 1);
+
+ /* Turn off slave PHY LP-RX clk lane */
+ dwc_dphy_ifc_write_mask(isys, slave, 0x304, 0x1, 7, 1);
+ dwc_dphy_ifc_write_mask(isys, slave, 0x305, 0xa, 0, 5);
+}
+
+#define PHY_E 4
+static int ipu6_isys_dwc_phy_powerup_ack(struct ipu6_isys *isys, u32 phy_id)
+{
+ struct device *dev = &isys->adev->auxdev.dev;
+ u32 rescal_done;
+ int ret;
+
+ ret = dwc_dphy_pwr_up(isys, phy_id);
+ if (ret != 0) {
+ dev_err(dev, "Dphy %u power up failed(%d)", phy_id, ret);
+ return ret;
+ }
+
+ /* reset forcerxmode */
+ dwc_dphy_write_mask(isys, phy_id, IPU6_DWC_DPHY_DFT_CTRL2, 0, 4, 1);
+ dwc_dphy_write_mask(isys, phy_id, IPU6_DWC_DPHY_DFT_CTRL2, 0, 8, 1);
+
+ dev_dbg(dev, "Dphy %u is ready!", phy_id);
+
+ if (phy_id != PHY_E || isys->phy_termcal_val)
+ return 0;
+
+ usleep_range(100, 200);
+ rescal_done = dwc_dphy_ifc_read_mask(isys, phy_id, 0x221, 7, 1);
+ if (rescal_done) {
+ isys->phy_termcal_val = dwc_dphy_ifc_read_mask(isys, phy_id,
+ 0x220, 2, 4);
+ dev_dbg(dev, "termcal done with value = %u",
+ isys->phy_termcal_val);
+ }
+
+ return 0;
+}
+
+static void ipu6_isys_dwc_phy_reset(struct ipu6_isys *isys, u32 phy_id)
+{
+ dev_dbg(&isys->adev->auxdev.dev, "Reset phy %u", phy_id);
+
+ dwc_dphy_write(isys, phy_id, IPU6_DWC_DPHY_SHUTDOWNZ, 0);
+ dwc_dphy_write(isys, phy_id, IPU6_DWC_DPHY_RSTZ, 0);
+ dwc_dphy_write(isys, phy_id, IPU6_DWC_DPHY_TEST_IFC_ACCESS_MODE,
+ TEST_IFC_ACCESS_MODE_FSM);
+ dwc_dphy_write(isys, phy_id, IPU6_DWC_DPHY_TEST_IFC_REQ,
+ TEST_IFC_REQ_RESET);
+}
+
+int ipu6_isys_dwc_phy_set_power(struct ipu6_isys *isys,
+ struct ipu6_isys_csi2_config *cfg,
+ const struct ipu6_isys_csi2_timing *timing,
+ bool on)
+{
+ struct device *dev = &isys->adev->auxdev.dev;
+ void __iomem *isys_base = isys->pdata->base;
+ u32 phy_id, primary, secondary;
+ u32 nlanes, port, mbps;
+ s64 link_freq;
+ int ret;
+
+ port = cfg->port;
+
+ if (!isys_base || port >= isys->pdata->ipdata->csi2.nports) {
+ dev_warn(dev, "invalid port ID %d\n", port);
+ return -EINVAL;
+ }
+
+ nlanes = cfg->nlanes;
+ /* only port 0, 2 and 4 support 4 lanes */
+ if (nlanes == 4 && port % 2) {
+ dev_err(dev, "invalid csi-port %u with %u lanes\n", port,
+ nlanes);
+ return -EINVAL;
+ }
+
+ link_freq = ipu6_isys_csi2_get_link_freq(&isys->csi2[port]);
+ if (link_freq < 0) {
+ dev_err(dev, "get link freq failed(%lld).\n", link_freq);
+ return link_freq;
+ }
+
+ mbps = div_u64(link_freq, 500000);
+
+ phy_id = port;
+ primary = port & ~1;
+ secondary = primary + 1;
+ if (on) {
+ if (nlanes == 4) {
+ dev_dbg(dev, "config phy %u and %u in aggr mode\n",
+ primary, secondary);
+
+ ipu6_isys_dwc_phy_reset(isys, primary);
+ ipu6_isys_dwc_phy_reset(isys, secondary);
+ ipu6_isys_dwc_phy_aggr_setup(isys, primary,
+ secondary, mbps);
+
+ ret = ipu6_isys_dwc_phy_config(isys, primary, mbps);
+ if (ret)
+ return ret;
+ ret = ipu6_isys_dwc_phy_config(isys, secondary, mbps);
+ if (ret)
+ return ret;
+
+ ret = ipu6_isys_dwc_phy_powerup_ack(isys, primary);
+ if (ret)
+ return ret;
+
+ ret = ipu6_isys_dwc_phy_powerup_ack(isys, secondary);
+ return ret;
+ }
+
+ dev_dbg(dev, "config phy %u with %u lanes in non-aggr mode\n",
+ phy_id, nlanes);
+
+ ipu6_isys_dwc_phy_reset(isys, phy_id);
+ ret = ipu6_isys_dwc_phy_config(isys, phy_id, mbps);
+ if (ret)
+ return ret;
+
+ ret = ipu6_isys_dwc_phy_powerup_ack(isys, phy_id);
+ return ret;
+ }
+
+ if (nlanes == 4) {
+ dev_dbg(dev, "Power down phy %u and phy %u for port %u\n",
+ primary, secondary, port);
+ ipu6_isys_dwc_phy_reset(isys, secondary);
+ ipu6_isys_dwc_phy_reset(isys, primary);
+
+ return 0;
+ }
+
+ dev_dbg(dev, "Powerdown phy %u with %u lanes\n", phy_id, nlanes);
+
+ ipu6_isys_dwc_phy_reset(isys, phy_id);
+
+ return 0;
+}
new file mode 100644
@@ -0,0 +1,237 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2013 - 2023 Intel Corporation
+ */
+#include <linux/bitfield.h>
+
+#include "ipu6-isys.h"
+#include "ipu6-platform-isys-csi2-reg.h"
+#include "ipu6-platform-regs.h"
+
+/* only use BB0, BB2, BB4, and BB6 on PHY0 */
+#define IPU6SE_ISYS_PHY_BB_NUM 4
+#define IPU6SE_ISYS_PHY_0_BASE 0x10000
+
+#define PHY_CPHY_DLL_OVRD(x) (0x100 + 0x100 * (x))
+#define PHY_CPHY_RX_CONTROL1(x) (0x110 + 0x100 * (x))
+#define PHY_DPHY_CFG(x) (0x148 + 0x100 * (x))
+#define PHY_BB_AFE_CONFIG(x) (0x174 + 0x100 * (x))
+
+/*
+ * use port_cfg to configure that which data lanes used
+ * +---------+ +------+ +-----+
+ * | port0 x4<-----| | | |
+ * | | | port | | |
+ * | port1 x2<-----| | | |
+ * | | | <-| PHY |
+ * | port2 x4<-----| | | |
+ * | | |config| | |
+ * | port3 x2<-----| | | |
+ * +---------+ +------+ +-----+
+ */
+static const unsigned int csi2_port_cfg[][3] = {
+ {0, 0, 0x1f}, /* no link */
+ {4, 0, 0x10}, /* x4 + x4 config */
+ {2, 0, 0x12}, /* x2 + x2 config */
+ {1, 0, 0x13}, /* x1 + x1 config */
+ {2, 1, 0x15}, /* x2x1 + x2x1 config */
+ {1, 1, 0x16}, /* x1x1 + x1x1 config */
+ {2, 2, 0x18}, /* x2x2 + x2x2 config */
+ {1, 2, 0x19} /* x1x2 + x1x2 config */
+};
+
+/* port, nlanes, bbindex, portcfg */
+static const unsigned int phy_port_cfg[][4] = {
+ /* sip0 */
+ {0, 1, 0, 0x15},
+ {0, 2, 0, 0x15},
+ {0, 4, 0, 0x15},
+ {0, 4, 2, 0x22},
+ /* sip1 */
+ {2, 1, 4, 0x15},
+ {2, 2, 4, 0x15},
+ {2, 4, 4, 0x15},
+ {2, 4, 6, 0x22}
+};
+
+static void ipu6_isys_csi2_phy_config_by_port(struct ipu6_isys *isys,
+ unsigned int port,
+ unsigned int nlanes)
+{
+ struct device *dev = &isys->adev->auxdev.dev;
+ void __iomem *base = isys->adev->isp->base;
+ unsigned int bbnum;
+ u32 val, reg, i;
+
+ dev_dbg(dev, "port %u with %u lanes", port, nlanes);
+
+ /* only support <1.5Gbps */
+ for (i = 0; i < IPU6SE_ISYS_PHY_BB_NUM; i++) {
+ /* cphy_dll_ovrd.crcdc_fsm_dlane0 = 13 */
+ reg = IPU6SE_ISYS_PHY_0_BASE + PHY_CPHY_DLL_OVRD(i);
+ val = readl(base + reg);
+ val |= FIELD_PREP(GENMASK(6, 1), 13);
+ writel(val, base + reg);
+
+ /* cphy_rx_control1.en_crc1 = 1 */
+ reg = IPU6SE_ISYS_PHY_0_BASE + PHY_CPHY_RX_CONTROL1(i);
+ val = readl(base + reg);
+ val |= BIT(31);
+ writel(val, base + reg);
+
+ /* dphy_cfg.reserved = 1, .lden_from_dll_ovrd_0 = 1 */
+ reg = IPU6SE_ISYS_PHY_0_BASE + PHY_DPHY_CFG(i);
+ val = readl(base + reg);
+ val |= BIT(25) | BIT(26);
+ writel(val, base + reg);
+
+ /* cphy_dll_ovrd.lden_crcdc_fsm_dlane0 = 1 */
+ reg = IPU6SE_ISYS_PHY_0_BASE + PHY_CPHY_DLL_OVRD(i);
+ val = readl(base + reg);
+ val |= BIT(0);
+ writel(val, base + reg);
+ }
+
+ /* Front end config, use minimal channel loss */
+ for (i = 0; i < ARRAY_SIZE(phy_port_cfg); i++) {
+ if (phy_port_cfg[i][0] == port &&
+ phy_port_cfg[i][1] == nlanes) {
+ bbnum = phy_port_cfg[i][2] / 2;
+ reg = IPU6SE_ISYS_PHY_0_BASE + PHY_BB_AFE_CONFIG(bbnum);
+ val = readl(base + reg);
+ val |= phy_port_cfg[i][3];
+ writel(val, base + reg);
+ }
+ }
+}
+
+static void ipu6_isys_csi2_rx_control(struct ipu6_isys *isys)
+{
+ void __iomem *base = isys->adev->isp->base;
+ u32 val, reg;
+
+ reg = CSI2_HUB_GPREG_SIP0_CSI_RX_A_CONTROL;
+ val = readl(base + reg);
+ val |= BIT(0);
+ writel(val, base + CSI2_HUB_GPREG_SIP0_CSI_RX_A_CONTROL);
+
+ reg = CSI2_HUB_GPREG_SIP0_CSI_RX_B_CONTROL;
+ val = readl(base + reg);
+ val |= BIT(0);
+ writel(val, base + CSI2_HUB_GPREG_SIP0_CSI_RX_B_CONTROL);
+
+ reg = CSI2_HUB_GPREG_SIP1_CSI_RX_A_CONTROL;
+ val = readl(base + reg);
+ val |= BIT(0);
+ writel(val, base + CSI2_HUB_GPREG_SIP1_CSI_RX_A_CONTROL);
+
+ reg = CSI2_HUB_GPREG_SIP1_CSI_RX_B_CONTROL;
+ val = readl(base + reg);
+ val |= BIT(0);
+ writel(val, base + CSI2_HUB_GPREG_SIP1_CSI_RX_B_CONTROL);
+}
+
+static int ipu6_isys_csi2_set_port_cfg(struct ipu6_isys *isys,
+ unsigned int port, unsigned int nlanes)
+{
+ struct device *dev = &isys->adev->auxdev.dev;
+ unsigned int sip = port / 2;
+ unsigned int index;
+
+ switch (nlanes) {
+ case 1:
+ index = 5;
+ break;
+ case 2:
+ index = 6;
+ break;
+ case 4:
+ index = 1;
+ break;
+ default:
+ dev_err(dev, "lanes nr %u is unsupported\n", nlanes);
+ return -EINVAL;
+ }
+
+ dev_dbg(dev, "port config for port %u with %u lanes\n", port, nlanes);
+
+ writel(csi2_port_cfg[index][2],
+ isys->pdata->base + CSI2_HUB_GPREG_SIP_FB_PORT_CFG(sip));
+
+ return 0;
+}
+
+static void
+ipu6_isys_csi2_set_timing(struct ipu6_isys *isys,
+ const struct ipu6_isys_csi2_timing *timing,
+ unsigned int port, unsigned int nlanes)
+{
+ struct device *dev = &isys->adev->auxdev.dev;
+ void __iomem *reg;
+ u32 port_base;
+ u32 i;
+
+ port_base = (port % 2) ? CSI2_SIP_TOP_CSI_RX_PORT_BASE_1(port) :
+ CSI2_SIP_TOP_CSI_RX_PORT_BASE_0(port);
+
+ dev_dbg(dev, "set timing for port %u with %u lanes\n", port, nlanes);
+
+ reg = isys->pdata->base + port_base;
+ reg += CSI2_SIP_TOP_CSI_RX_DLY_CNT_TERMEN_CLANE;
+
+ writel(timing->ctermen, reg);
+
+ reg = isys->pdata->base + port_base;
+ reg += CSI2_SIP_TOP_CSI_RX_DLY_CNT_SETTLE_CLANE;
+ writel(timing->csettle, reg);
+
+ for (i = 0; i < nlanes; i++) {
+ reg = isys->pdata->base + port_base;
+ reg += CSI2_SIP_TOP_CSI_RX_DLY_CNT_TERMEN_DLANE(i);
+ writel(timing->dtermen, reg);
+
+ reg = isys->pdata->base + port_base;
+ reg += CSI2_SIP_TOP_CSI_RX_DLY_CNT_SETTLE_DLANE(i);
+ writel(timing->dsettle, reg);
+ }
+}
+
+#define DPHY_TIMER_INCR 0x28
+int ipu6_isys_jsl_phy_set_power(struct ipu6_isys *isys,
+ struct ipu6_isys_csi2_config *cfg,
+ const struct ipu6_isys_csi2_timing *timing,
+ bool on)
+{
+ struct device *dev = &isys->adev->auxdev.dev;
+ void __iomem *isys_base = isys->pdata->base;
+ int ret = 0;
+ u32 nlanes;
+ u32 port;
+
+ if (!on)
+ return 0;
+
+ port = cfg->port;
+ nlanes = cfg->nlanes;
+
+ if (!isys_base || port >= isys->pdata->ipdata->csi2.nports) {
+ dev_warn(dev, "invalid port ID %d\n", port);
+ return -EINVAL;
+ }
+
+ ipu6_isys_csi2_phy_config_by_port(isys, port, nlanes);
+
+ writel(DPHY_TIMER_INCR,
+ isys->pdata->base + CSI2_HUB_GPREG_DPHY_TIMER_INCR);
+
+ /* set port cfg and rx timing */
+ ipu6_isys_csi2_set_timing(isys, timing, port, nlanes);
+
+ ret = ipu6_isys_csi2_set_port_cfg(isys, port, nlanes);
+ if (ret)
+ return ret;
+
+ ipu6_isys_csi2_rx_control(isys);
+
+ return 0;
+}
new file mode 100644
@@ -0,0 +1,712 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2013 - 2023 Intel Corporation
+ */
+#include <linux/delay.h>
+#include <linux/iopoll.h>
+
+#include <media/v4l2-async.h>
+
+#include "ipu6-isys.h"
+#include "ipu6-platform-isys-csi2-reg.h"
+#include "ipu6-platform-regs.h"
+
+#define CSI_REG_HUB_GPREG_PHY_CTL(id) (CSI_REG_BASE + 0x18008 + (id) * 0x8)
+#define CSI_REG_HUB_GPREG_PHY_CTL_RESET BIT(4)
+#define CSI_REG_HUB_GPREG_PHY_CTL_PWR_EN BIT(0)
+#define CSI_REG_HUB_GPREG_PHY_STATUS(id) (CSI_REG_BASE + 0x1800c + (id) * 0x8)
+#define CSI_REG_HUB_GPREG_PHY_POWER_ACK BIT(0)
+#define CSI_REG_HUB_GPREG_PHY_READY BIT(4)
+
+#define MCD_PHY_POWER_STATUS_TIMEOUT (200 * USEC_PER_MSEC)
+
+/*
+ * bridge to phy in buttress reg map, each phy has 16 kbytes
+ * only 2 phys for TGL U and Y
+ */
+#define IPU6_ISYS_MCD_PHY_BASE(i) (0x10000 + (i) * 0x4000)
+
+/*
+ * There are 2 MCD DPHY instances on TGL and 1 MCD DPHY instance on ADL.
+ * Each MCD PHY has 12-lanes which has 8 data lanes and 4 clock lanes.
+ * CSI port 1, 3 (5, 7) can support max 2 data lanes.
+ * CSI port 0, 2 (4, 6) can support max 4 data lanes.
+ * PHY configurations are PPI based instead of port.
+ * Left:
+ * +---------+---------+---------+---------+--------+---------+----------+
+ * | | | | | | | |
+ * | PPI | PPI5 | PPI4 | PPI3 | PPI2 | PPI1 | PPI0 |
+ * +---------+---------+---------+---------+--------+---------+----------+
+ * | | | | | | | |
+ * | x4 | unused | D3 | D2 | C0 | D0 | D1 |
+ * |---------+---------+---------+---------+--------+---------+----------+
+ * | | | | | | | |
+ * | x2x2 | C1 | D0 | D1 | C0 | D0 | D1 |
+ * ----------+---------+---------+---------+--------+---------+----------+
+ * | | | | | | | |
+ * | x2x1 | C1 | D0 | unused | C0 | D0 | D1 |
+ * +---------+---------+---------+---------+--------+---------+----------+
+ * | | | | | | | |
+ * | x1x1 | C1 | D0 | unused | C0 | D0 | unused |
+ * +---------+---------+---------+---------+--------+---------+----------+
+ * | | | | | | | |
+ * | x1x2 | C1 | D0 | D1 | C0 | D0 | unused |
+ * +---------+---------+---------+---------+--------+---------+----------+
+ *
+ * Right:
+ * +---------+---------+---------+---------+--------+---------+----------+
+ * | | | | | | | |
+ * | PPI | PPI6 | PPI7 | PPI8 | PPI9 | PPI10 | PPI11 |
+ * +---------+---------+---------+---------+--------+---------+----------+
+ * | | | | | | | |
+ * | x4 | D1 | D0 | C2 | D2 | D3 | unused |
+ * |---------+---------+---------+---------+--------+---------+----------+
+ * | | | | | | | |
+ * | x2x2 | D1 | D0 | C2 | D1 | D0 | C3 |
+ * ----------+---------+---------+---------+--------+---------+----------+
+ * | | | | | | | |
+ * | x2x1 | D1 | D0 | C2 | unused | D0 | C3 |
+ * +---------+---------+---------+---------+--------+---------+----------+
+ * | | | | | | | |
+ * | x1x1 | unused | D0 | C2 | unused | D0 | C3 |
+ * +---------+---------+---------+---------+--------+---------+----------+
+ * | | | | | | | |
+ * | x1x2 | unused | D0 | C2 | D1 | D0 | C3 |
+ * +---------+---------+---------+---------+--------+---------+----------+
+ *
+ * ppi mapping per phy :
+ *
+ * x4 + x4:
+ * Left : port0 - PPI range {0, 1, 2, 3, 4}
+ * Right: port2 - PPI range {6, 7, 8, 9, 10}
+ *
+ * x4 + x2x2:
+ * Left: port0 - PPI range {0, 1, 2, 3, 4}
+ * Right: port2 - PPI range {6, 7, 8}, port3 - PPI range {9, 10, 11}
+ *
+ * x2x2 + x4:
+ * Left: port0 - PPI range {0, 1, 2}, port1 - PPI range {3, 4, 5}
+ * Right: port2 - PPI range {6, 7, 8, 9, 10}
+ *
+ * x2x2 + x2x2:
+ * Left : port0 - PPI range {0, 1, 2}, port1 - PPI range {3, 4, 5}
+ * Right: port2 - PPI range {6, 7, 8}, port3 - PPI range {9, 10, 11}
+ */
+
+struct phy_reg {
+ u32 reg;
+ u32 val;
+};
+
+static const struct phy_reg common_init_regs[] = {
+ /* for TGL-U, use 0x80000000 */
+ {0x00000040, 0x80000000},
+ {0x00000044, 0x00a80880},
+ {0x00000044, 0x00b80880},
+ {0x00000010, 0x0000078c},
+ {0x00000344, 0x2f4401e2},
+ {0x00000544, 0x924401e2},
+ {0x00000744, 0x594401e2},
+ {0x00000944, 0x624401e2},
+ {0x00000b44, 0xfc4401e2},
+ {0x00000d44, 0xc54401e2},
+ {0x00000f44, 0x034401e2},
+ {0x00001144, 0x8f4401e2},
+ {0x00001344, 0x754401e2},
+ {0x00001544, 0xe94401e2},
+ {0x00001744, 0xcb4401e2},
+ {0x00001944, 0xfa4401e2}
+};
+
+static const struct phy_reg x1_port0_config_regs[] = {
+ {0x00000694, 0xc80060fa},
+ {0x00000680, 0x3d4f78ea},
+ {0x00000690, 0x10a0140b},
+ {0x000006a8, 0xdf04010a},
+ {0x00000700, 0x57050060},
+ {0x00000710, 0x0030001c},
+ {0x00000738, 0x5f004444},
+ {0x0000073c, 0x78464204},
+ {0x00000748, 0x7821f940},
+ {0x0000074c, 0xb2000433},
+ {0x00000494, 0xfe6030fa},
+ {0x00000480, 0x29ef5ed0},
+ {0x00000490, 0x10a0540b},
+ {0x000004a8, 0x7a01010a},
+ {0x00000500, 0xef053460},
+ {0x00000510, 0xe030101c},
+ {0x00000538, 0xdf808444},
+ {0x0000053c, 0xc8422204},
+ {0x00000540, 0x0180088c},
+ {0x00000574, 0x00000000},
+ {0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x1_port1_config_regs[] = {
+ {0x00000c94, 0xc80060fa},
+ {0x00000c80, 0xcf47abea},
+ {0x00000c90, 0x10a0840b},
+ {0x00000ca8, 0xdf04010a},
+ {0x00000d00, 0x57050060},
+ {0x00000d10, 0x0030001c},
+ {0x00000d38, 0x5f004444},
+ {0x00000d3c, 0x78464204},
+ {0x00000d48, 0x7821f940},
+ {0x00000d4c, 0xb2000433},
+ {0x00000a94, 0xc91030fa},
+ {0x00000a80, 0x5a166ed0},
+ {0x00000a90, 0x10a0540b},
+ {0x00000aa8, 0x5d060100},
+ {0x00000b00, 0xef053460},
+ {0x00000b10, 0xa030101c},
+ {0x00000b38, 0xdf808444},
+ {0x00000b3c, 0xc8422204},
+ {0x00000b40, 0x0180088c},
+ {0x00000b74, 0x00000000},
+ {0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x1_port2_config_regs[] = {
+ {0x00001294, 0x28f000fa},
+ {0x00001280, 0x08130cea},
+ {0x00001290, 0x10a0140b},
+ {0x000012a8, 0xd704010a},
+ {0x00001300, 0x8d050060},
+ {0x00001310, 0x0030001c},
+ {0x00001338, 0xdf008444},
+ {0x0000133c, 0x78422204},
+ {0x00001348, 0x7821f940},
+ {0x0000134c, 0x5a000433},
+ {0x00001094, 0x2d20b0fa},
+ {0x00001080, 0xade75dd0},
+ {0x00001090, 0x10a0540b},
+ {0x000010a8, 0xb101010a},
+ {0x00001100, 0x33053460},
+ {0x00001110, 0x0030101c},
+ {0x00001138, 0xdf808444},
+ {0x0000113c, 0xc8422204},
+ {0x00001140, 0x8180088c},
+ {0x00001174, 0x00000000},
+ {0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x1_port3_config_regs[] = {
+ {0x00001894, 0xc80060fa},
+ {0x00001880, 0x0f90fd6a},
+ {0x00001890, 0x10a0840b},
+ {0x000018a8, 0xdf04010a},
+ {0x00001900, 0x57050060},
+ {0x00001910, 0x0030001c},
+ {0x00001938, 0x5f004444},
+ {0x0000193c, 0x78464204},
+ {0x00001948, 0x7821f940},
+ {0x0000194c, 0xb2000433},
+ {0x00001694, 0x3050d0fa},
+ {0x00001680, 0x0ef6d050},
+ {0x00001690, 0x10a0540b},
+ {0x000016a8, 0xe301010a},
+ {0x00001700, 0x69053460},
+ {0x00001710, 0xa030101c},
+ {0x00001738, 0xdf808444},
+ {0x0000173c, 0xc8422204},
+ {0x00001740, 0x0180088c},
+ {0x00001774, 0x00000000},
+ {0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x2_port0_config_regs[] = {
+ {0x00000694, 0xc80060fa},
+ {0x00000680, 0x3d4f78ea},
+ {0x00000690, 0x10a0140b},
+ {0x000006a8, 0xdf04010a},
+ {0x00000700, 0x57050060},
+ {0x00000710, 0x0030001c},
+ {0x00000738, 0x5f004444},
+ {0x0000073c, 0x78464204},
+ {0x00000748, 0x7821f940},
+ {0x0000074c, 0xb2000433},
+ {0x00000494, 0xc80060fa},
+ {0x00000480, 0x29ef5ed8},
+ {0x00000490, 0x10a0540b},
+ {0x000004a8, 0x7a01010a},
+ {0x00000500, 0xef053460},
+ {0x00000510, 0xe030101c},
+ {0x00000538, 0xdf808444},
+ {0x0000053c, 0xc8422204},
+ {0x00000540, 0x0180088c},
+ {0x00000574, 0x00000000},
+ {0x00000294, 0xc80060fa},
+ {0x00000280, 0xcb45b950},
+ {0x00000290, 0x10a0540b},
+ {0x000002a8, 0x8c01010a},
+ {0x00000300, 0xef053460},
+ {0x00000310, 0x8030101c},
+ {0x00000338, 0x41808444},
+ {0x0000033c, 0x32422204},
+ {0x00000340, 0x0180088c},
+ {0x00000374, 0x00000000},
+ {0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x2_port1_config_regs[] = {
+ {0x00000c94, 0xc80060fa},
+ {0x00000c80, 0xcf47abea},
+ {0x00000c90, 0x10a0840b},
+ {0x00000ca8, 0xdf04010a},
+ {0x00000d00, 0x57050060},
+ {0x00000d10, 0x0030001c},
+ {0x00000d38, 0x5f004444},
+ {0x00000d3c, 0x78464204},
+ {0x00000d48, 0x7821f940},
+ {0x00000d4c, 0xb2000433},
+ {0x00000a94, 0xc80060fa},
+ {0x00000a80, 0x5a166ed8},
+ {0x00000a90, 0x10a0540b},
+ {0x00000aa8, 0x7a01010a},
+ {0x00000b00, 0xef053460},
+ {0x00000b10, 0xa030101c},
+ {0x00000b38, 0xdf808444},
+ {0x00000b3c, 0xc8422204},
+ {0x00000b40, 0x0180088c},
+ {0x00000b74, 0x00000000},
+ {0x00000894, 0xc80060fa},
+ {0x00000880, 0x4d4f21d0},
+ {0x00000890, 0x10a0540b},
+ {0x000008a8, 0x5601010a},
+ {0x00000900, 0xef053460},
+ {0x00000910, 0x8030101c},
+ {0x00000938, 0xdf808444},
+ {0x0000093c, 0xc8422204},
+ {0x00000940, 0x0180088c},
+ {0x00000974, 0x00000000},
+ {0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x2_port2_config_regs[] = {
+ {0x00001294, 0xc80060fa},
+ {0x00001280, 0x08130cea},
+ {0x00001290, 0x10a0140b},
+ {0x000012a8, 0xd704010a},
+ {0x00001300, 0x8d050060},
+ {0x00001310, 0x0030001c},
+ {0x00001338, 0xdf008444},
+ {0x0000133c, 0x78422204},
+ {0x00001348, 0x7821f940},
+ {0x0000134c, 0x5a000433},
+ {0x00001094, 0xc80060fa},
+ {0x00001080, 0xade75dd8},
+ {0x00001090, 0x10a0540b},
+ {0x000010a8, 0xb101010a},
+ {0x00001100, 0x33053460},
+ {0x00001110, 0x0030101c},
+ {0x00001138, 0xdf808444},
+ {0x0000113c, 0xc8422204},
+ {0x00001140, 0x8180088c},
+ {0x00001174, 0x00000000},
+ {0x00000e94, 0xc80060fa},
+ {0x00000e80, 0x0fbf16d0},
+ {0x00000e90, 0x10a0540b},
+ {0x00000ea8, 0x7a01010a},
+ {0x00000f00, 0xf5053460},
+ {0x00000f10, 0xc030101c},
+ {0x00000f38, 0xdf808444},
+ {0x00000f3c, 0xc8422204},
+ {0x00000f40, 0x8180088c},
+ {0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x2_port3_config_regs[] = {
+ {0x00001894, 0xc80060fa},
+ {0x00001880, 0x0f90fd6a},
+ {0x00001890, 0x10a0840b},
+ {0x000018a8, 0xdf04010a},
+ {0x00001900, 0x57050060},
+ {0x00001910, 0x0030001c},
+ {0x00001938, 0x5f004444},
+ {0x0000193c, 0x78464204},
+ {0x00001948, 0x7821f940},
+ {0x0000194c, 0xb2000433},
+ {0x00001694, 0xc80060fa},
+ {0x00001680, 0x0ef6d058},
+ {0x00001690, 0x10a0540b},
+ {0x000016a8, 0x7a01010a},
+ {0x00001700, 0x69053460},
+ {0x00001710, 0xa030101c},
+ {0x00001738, 0xdf808444},
+ {0x0000173c, 0xc8422204},
+ {0x00001740, 0x0180088c},
+ {0x00001774, 0x00000000},
+ {0x00001494, 0xc80060fa},
+ {0x00001480, 0xf9d34bd0},
+ {0x00001490, 0x10a0540b},
+ {0x000014a8, 0x7a01010a},
+ {0x00001500, 0x1b053460},
+ {0x00001510, 0x0030101c},
+ {0x00001538, 0xdf808444},
+ {0x0000153c, 0xc8422204},
+ {0x00001540, 0x8180088c},
+ {0x00001574, 0x00000000},
+ {0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x4_port0_config_regs[] = {
+ {0x00000694, 0xc80060fa},
+ {0x00000680, 0x3d4f78fa},
+ {0x00000690, 0x10a0140b},
+ {0x000006a8, 0xdf04010a},
+ {0x00000700, 0x57050060},
+ {0x00000710, 0x0030001c},
+ {0x00000738, 0x5f004444},
+ {0x0000073c, 0x78464204},
+ {0x00000748, 0x7821f940},
+ {0x0000074c, 0xb2000433},
+ {0x00000494, 0xfe6030fa},
+ {0x00000480, 0x29ef5ed8},
+ {0x00000490, 0x10a0540b},
+ {0x000004a8, 0x7a01010a},
+ {0x00000500, 0xef053460},
+ {0x00000510, 0xe030101c},
+ {0x00000538, 0xdf808444},
+ {0x0000053c, 0xc8422204},
+ {0x00000540, 0x0180088c},
+ {0x00000574, 0x00000004},
+ {0x00000294, 0x23e030fa},
+ {0x00000280, 0xcb45b950},
+ {0x00000290, 0x10a0540b},
+ {0x000002a8, 0x8c01010a},
+ {0x00000300, 0xef053460},
+ {0x00000310, 0x8030101c},
+ {0x00000338, 0x41808444},
+ {0x0000033c, 0x32422204},
+ {0x00000340, 0x0180088c},
+ {0x00000374, 0x00000004},
+ {0x00000894, 0x5620b0fa},
+ {0x00000880, 0x4d4f21dc},
+ {0x00000890, 0x10a0540b},
+ {0x000008a8, 0x5601010a},
+ {0x00000900, 0xef053460},
+ {0x00000910, 0x8030101c},
+ {0x00000938, 0xdf808444},
+ {0x0000093c, 0xc8422204},
+ {0x00000940, 0x0180088c},
+ {0x00000974, 0x00000004},
+ {0x00000a94, 0xc91030fa},
+ {0x00000a80, 0x5a166ecc},
+ {0x00000a90, 0x10a0540b},
+ {0x00000aa8, 0x5d01010a},
+ {0x00000b00, 0xef053460},
+ {0x00000b10, 0xa030101c},
+ {0x00000b38, 0xdf808444},
+ {0x00000b3c, 0xc8422204},
+ {0x00000b40, 0x0180088c},
+ {0x00000b74, 0x00000004},
+ {0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x4_port1_config_regs[] = {
+ {0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x4_port2_config_regs[] = {
+ {0x00001294, 0x28f000fa},
+ {0x00001280, 0x08130cfa},
+ {0x00001290, 0x10c0140b},
+ {0x000012a8, 0xd704010a},
+ {0x00001300, 0x8d050060},
+ {0x00001310, 0x0030001c},
+ {0x00001338, 0xdf008444},
+ {0x0000133c, 0x78422204},
+ {0x00001348, 0x7821f940},
+ {0x0000134c, 0x5a000433},
+ {0x00001094, 0x2d20b0fa},
+ {0x00001080, 0xade75dd8},
+ {0x00001090, 0x10a0540b},
+ {0x000010a8, 0xb101010a},
+ {0x00001100, 0x33053460},
+ {0x00001110, 0x0030101c},
+ {0x00001138, 0xdf808444},
+ {0x0000113c, 0xc8422204},
+ {0x00001140, 0x8180088c},
+ {0x00001174, 0x00000004},
+ {0x00000e94, 0xd308d0fa},
+ {0x00000e80, 0x0fbf16d0},
+ {0x00000e90, 0x10a0540b},
+ {0x00000ea8, 0x2c01010a},
+ {0x00000f00, 0xf5053460},
+ {0x00000f10, 0xc030101c},
+ {0x00000f38, 0xdf808444},
+ {0x00000f3c, 0xc8422204},
+ {0x00000f40, 0x8180088c},
+ {0x00000f74, 0x00000004},
+ {0x00001494, 0x136850fa},
+ {0x00001480, 0xf9d34bdc},
+ {0x00001490, 0x10a0540b},
+ {0x000014a8, 0x5a01010a},
+ {0x00001500, 0x1b053460},
+ {0x00001510, 0x0030101c},
+ {0x00001538, 0xdf808444},
+ {0x0000153c, 0xc8422204},
+ {0x00001540, 0x8180088c},
+ {0x00001574, 0x00000004},
+ {0x00001694, 0x3050d0fa},
+ {0x00001680, 0x0ef6d04c},
+ {0x00001690, 0x10a0540b},
+ {0x000016a8, 0xe301010a},
+ {0x00001700, 0x69053460},
+ {0x00001710, 0xa030101c},
+ {0x00001738, 0xdf808444},
+ {0x0000173c, 0xc8422204},
+ {0x00001740, 0x0180088c},
+ {0x00001774, 0x00000004},
+ {0x00000000, 0x00000000}
+};
+
+static const struct phy_reg x4_port3_config_regs[] = {
+ {0x00000000, 0x00000000}
+};
+
+static const struct phy_reg *x1_config_regs[4] = {
+ x1_port0_config_regs,
+ x1_port1_config_regs,
+ x1_port2_config_regs,
+ x1_port3_config_regs
+};
+
+static const struct phy_reg *x2_config_regs[4] = {
+ x2_port0_config_regs,
+ x2_port1_config_regs,
+ x2_port2_config_regs,
+ x2_port3_config_regs
+};
+
+static const struct phy_reg *x4_config_regs[4] = {
+ x4_port0_config_regs,
+ x4_port1_config_regs,
+ x4_port2_config_regs,
+ x4_port3_config_regs
+};
+
+static const struct phy_reg **config_regs[3] = {
+ x1_config_regs,
+ x2_config_regs,
+ x4_config_regs
+};
+
+static int ipu6_isys_mcd_phy_powerup_ack(struct ipu6_isys *isys, u8 id)
+{
+ struct device *dev = &isys->adev->auxdev.dev;
+ void __iomem *isys_base = isys->pdata->base;
+ u32 val;
+ int ret;
+
+ val = readl(isys_base + CSI_REG_HUB_GPREG_PHY_CTL(id));
+ val |= CSI_REG_HUB_GPREG_PHY_CTL_PWR_EN;
+ writel(val, isys_base + CSI_REG_HUB_GPREG_PHY_CTL(id));
+
+ ret = readl_poll_timeout(isys_base + CSI_REG_HUB_GPREG_PHY_STATUS(id),
+ val, val & CSI_REG_HUB_GPREG_PHY_POWER_ACK,
+ 200, MCD_PHY_POWER_STATUS_TIMEOUT);
+ if (ret)
+ dev_err(dev, "PHY%d powerup ack timeout", id);
+
+ return ret;
+}
+
+static int ipu6_isys_mcd_phy_powerdown_ack(struct ipu6_isys *isys, u8 id)
+{
+ struct device *dev = &isys->adev->auxdev.dev;
+ void __iomem *isys_base = isys->pdata->base;
+ u32 val;
+ int ret;
+
+ writel(0, isys_base + CSI_REG_HUB_GPREG_PHY_CTL(id));
+ ret = readl_poll_timeout(isys_base + CSI_REG_HUB_GPREG_PHY_STATUS(id),
+ val, !(val & CSI_REG_HUB_GPREG_PHY_POWER_ACK),
+ 200, MCD_PHY_POWER_STATUS_TIMEOUT);
+ if (ret)
+ dev_err(dev, "PHY%d powerdown ack timeout", id);
+
+ return ret;
+}
+
+static void ipu6_isys_mcd_phy_reset(struct ipu6_isys *isys, u8 id, bool assert)
+{
+ void __iomem *isys_base = isys->pdata->base;
+ u32 val;
+
+ val = readl(isys_base + CSI_REG_HUB_GPREG_PHY_CTL(id));
+ if (assert)
+ val |= CSI_REG_HUB_GPREG_PHY_CTL_RESET;
+ else
+ val &= ~(CSI_REG_HUB_GPREG_PHY_CTL_RESET);
+
+ writel(val, isys_base + CSI_REG_HUB_GPREG_PHY_CTL(id));
+}
+
+static int ipu6_isys_mcd_phy_ready(struct ipu6_isys *isys, u8 id)
+{
+ struct device *dev = &isys->adev->auxdev.dev;
+ void __iomem *isys_base = isys->pdata->base;
+ u32 val;
+ int ret;
+
+ ret = readl_poll_timeout(isys_base + CSI_REG_HUB_GPREG_PHY_STATUS(id),
+ val, val & CSI_REG_HUB_GPREG_PHY_READY,
+ 200, MCD_PHY_POWER_STATUS_TIMEOUT);
+ if (ret)
+ dev_err(dev, "PHY%d ready ack timeout", id);
+
+ return ret;
+}
+
+static void ipu6_isys_mcd_phy_common_init(struct ipu6_isys *isys)
+{
+ struct ipu6_bus_device *adev = isys->adev;
+ struct ipu6_device *isp = adev->isp;
+ void __iomem *isp_base = isp->base;
+ struct sensor_async_sd *s_asd;
+ struct v4l2_async_connection *asc;
+ void __iomem *phy_base;
+ unsigned int i;
+ u8 phy_id;
+
+ list_for_each_entry(asc, &isys->notifier.done_list, asc_entry) {
+ s_asd = container_of(asc, struct sensor_async_sd, asc);
+ phy_id = s_asd->csi2.port / 4;
+ phy_base = isp_base + IPU6_ISYS_MCD_PHY_BASE(phy_id);
+
+ for (i = 0; i < ARRAY_SIZE(common_init_regs); i++)
+ writel(common_init_regs[i].val,
+ phy_base + common_init_regs[i].reg);
+ }
+}
+
+static int ipu6_isys_driver_port_to_phy_port(struct ipu6_isys_csi2_config *cfg)
+{
+ int phy_port;
+ int ret;
+
+ if (!(cfg->nlanes == 4 || cfg->nlanes == 2 || cfg->nlanes == 1))
+ return -EINVAL;
+
+ /* B,F -> C0 A,E -> C1 C,G -> C2 D,H -> C4 */
+ /* normalize driver port number */
+ phy_port = cfg->port % 4;
+
+ /* swap port number only for A and B */
+ if (phy_port == 0)
+ phy_port = 1;
+ else if (phy_port == 1)
+ phy_port = 0;
+
+ ret = phy_port;
+
+ /* check validity per lane configuration */
+ if (cfg->nlanes == 4 && !(phy_port == 0 || phy_port == 2))
+ ret = -EINVAL;
+ else if ((cfg->nlanes == 2 || cfg->nlanes == 1) &&
+ !(phy_port >= 0 && phy_port <= 3))
+ ret = -EINVAL;
+
+ return ret;
+}
+
+static int ipu6_isys_mcd_phy_config(struct ipu6_isys *isys)
+{
+ struct device *dev = &isys->adev->auxdev.dev;
+ struct ipu6_bus_device *adev = isys->adev;
+ const struct phy_reg **phy_config_regs;
+ struct ipu6_device *isp = adev->isp;
+ void __iomem *isp_base = isp->base;
+ struct sensor_async_sd *s_asd;
+ struct ipu6_isys_csi2_config cfg;
+ struct v4l2_async_connection *asc;
+ u8 phy_port, phy_id;
+ unsigned int i;
+ void __iomem *phy_base;
+
+ list_for_each_entry(asc, &isys->notifier.done_list, asc_entry) {
+ s_asd = container_of(asc, struct sensor_async_sd, asc);
+ cfg.port = s_asd->csi2.port;
+ cfg.nlanes = s_asd->csi2.nlanes;
+ phy_port = ipu6_isys_driver_port_to_phy_port(&cfg);
+ if (phy_port < 0) {
+ dev_err(dev, "invalid port %d for lane %d", cfg.port,
+ cfg.nlanes);
+ return -ENXIO;
+ }
+
+ phy_id = cfg.port / 4;
+ phy_base = isp_base + IPU6_ISYS_MCD_PHY_BASE(phy_id);
+ dev_dbg(dev, "port%d PHY%u lanes %u\n", cfg.port, phy_id,
+ cfg.nlanes);
+
+ phy_config_regs = config_regs[cfg.nlanes / 2];
+ cfg.port = phy_port;
+ for (i = 0; phy_config_regs[cfg.port][i].reg; i++)
+ writel(phy_config_regs[cfg.port][i].val,
+ phy_base + phy_config_regs[cfg.port][i].reg);
+ }
+
+ return 0;
+}
+
+#define CSI_MCD_PHY_NUM 2
+static refcount_t phy_power_ref_count[CSI_MCD_PHY_NUM];
+
+int ipu6_isys_mcd_phy_set_power(struct ipu6_isys *isys,
+ struct ipu6_isys_csi2_config *cfg,
+ const struct ipu6_isys_csi2_timing *timing,
+ bool on)
+{
+ struct device *dev = &isys->adev->auxdev.dev;
+ void __iomem *isys_base = isys->pdata->base;
+ u8 port, phy_id;
+ refcount_t *ref;
+ int ret;
+
+ port = cfg->port;
+ phy_id = port / 4;
+
+ ref = &phy_power_ref_count[phy_id];
+
+ dev_dbg(dev, "for phy %d port %d, lanes: %d\n", phy_id, port,
+ cfg->nlanes);
+
+ if (!isys_base || port >= isys->pdata->ipdata->csi2.nports) {
+ dev_warn(dev, "invalid port ID %d\n", port);
+ return -EINVAL;
+ }
+
+ if (on) {
+ if (refcount_read(ref)) {
+ dev_dbg(dev, "for phy %d is already UP", phy_id);
+ refcount_inc(ref);
+ return 0;
+ }
+
+ ret = ipu6_isys_mcd_phy_powerup_ack(isys, phy_id);
+ if (ret)
+ return ret;
+
+ ipu6_isys_mcd_phy_reset(isys, phy_id, 0);
+ ipu6_isys_mcd_phy_common_init(isys);
+
+ ret = ipu6_isys_mcd_phy_config(isys);
+ if (ret)
+ return ret;
+
+ ipu6_isys_mcd_phy_reset(isys, phy_id, 1);
+ ret = ipu6_isys_mcd_phy_ready(isys, phy_id);
+ if (ret)
+ return ret;
+
+ refcount_set(ref, 1);
+ return 0;
+ }
+
+ if (!refcount_dec_and_test(ref))
+ return 0;
+
+ return ipu6_isys_mcd_phy_powerdown_ack(isys, phy_id);
+}