[v2] media: ov08x40: Avoid sensor probing in D0 state

Commit Message

Chen, Jason Z Jan. 22, 2024, 2:54 a.m. UTC

From: Jason Chen <[e-mail]>

When the system enters the D0 state and attempt to probe the device,
another component, such as LED, will also be pulled high due to the
hardware design. It's advisable to keep the device being probed in
a different D state.

Signed-off-by: Jason Chen <[e-mail]>
---
 drivers/media/i2c/ov08x40.c | 32 +++++++++++++++++++++-----------
 1 file changed, 21 insertions(+), 11 deletions(-)

Patch

diff --git a/drivers/media/i2c/ov08x40.c b/drivers/media/i2c/ov08x40.c
index ddcb4b6848b..4139efce42f 100644
--- a/drivers/media/i2c/ov08x40.c
+++ b/drivers/media/i2c/ov08x40.c
@@ -2453,6 +2453,9 @@  struct ov08x40 {
 
 	/* Mutex for serialized access */
 	struct mutex mutex;
+
+	/* True if the device has been identified */
+	bool identified;
 };
 
 #define to_ov08x40(_sd)	container_of(_sd, struct ov08x40, sd)
@@ -2997,6 +3000,9 @@  static int ov08x40_identify_module(struct ov08x40 *ov08x)
 	int ret;
 	u32 val;
 
+	if (ov08x->identified)
+		return 0;
+
 	ret = ov08x40_read_reg(ov08x, OV08X40_REG_CHIP_ID,
 			       OV08X40_REG_VALUE_24BIT, &val);
 	if (ret)
@@ -3005,9 +3011,11 @@  static int ov08x40_identify_module(struct ov08x40 *ov08x)
 	if (val != OV08X40_CHIP_ID) {
 		dev_err(&client->dev, "chip id mismatch: %x!=%x\n",
 			OV08X40_CHIP_ID, val);
-		return -EIO;
+		return -ENXIO;
 	}
 
+	ov08x->identified = true;
+
 	return 0;
 }
 
@@ -3225,6 +3233,7 @@  static int ov08x40_probe(struct i2c_client *client)
 {
 	struct ov08x40 *ov08x;
 	int ret;
+	bool full_power;
 
 	/* Check HW config */
 	ret = ov08x40_check_hwcfg(&client->dev);
@@ -3240,11 +3249,14 @@  static int ov08x40_probe(struct i2c_client *client)
 	/* Initialize subdev */
 	v4l2_i2c_subdev_init(&ov08x->sd, client, &ov08x40_subdev_ops);
 
-	/* Check module identity */
-	ret = ov08x40_identify_module(ov08x);
-	if (ret) {
-		dev_err(&client->dev, "failed to find sensor: %d\n", ret);
-		return ret;
+	full_power = acpi_dev_state_d0(&client->dev);
+	if (full_power) {
+		/* Check module identity */
+		ret = ov08x40_identify_module(ov08x);
+		if (ret) {
+			dev_err(&client->dev, "failed to find sensor: %d\n", ret);
+			return ret;
+		}
 	}
 
 	/* Set default mode to max resolution */
@@ -3272,11 +3284,8 @@  static int ov08x40_probe(struct i2c_client *client)
 	if (ret < 0)
 		goto error_media_entity;
 
-	/*
-	 * Device is already turned on by i2c-core with ACPI domain PM.
-	 * Enable runtime PM and turn off the device.
-	 */
-	pm_runtime_set_active(&client->dev);
+	if (full_power)
+		pm_runtime_set_active(&client->dev);
 	pm_runtime_enable(&client->dev);
 	pm_runtime_idle(&client->dev);
 
@@ -3320,6 +3329,7 @@  static struct i2c_driver ov08x40_i2c_driver = {
 	},
 	.probe = ov08x40_probe,
 	.remove = ov08x40_remove,
+	.flags = I2C_DRV_ACPI_WAIVE_D0_PROBE,
 };
 
 module_i2c_driver(ov08x40_i2c_driver);